Bertazzoni PROF486GGASXTLP, BERAMW100 Installation manual

Loading...

BERTAZZONI INSTALLATION MANUAL

FREESTANDING GAS RANGES

3070290

WWW.BERTAZZONI.COM

/ Table of contents

TABLE OF CONTENTS

WARNINGS ___________________________________________________________________

4

DATA RATING LABEL ___________________________________________________________

6

BEFORE INSTALLATION

________________________________________________________

6

VENTILATION PREPARATION ____________________________________________________

7

SPECIFICATIONS ______________________________________________________________

7

CLEARENCE DIMENSIONS ______________________________________________________

9

INSTALLATION REQUIREMENTS _________________________________________________

10

Electrical ___________________________________________________________________

10

Gas ________________________________________________________________________

10

ELECTRICAL CONNECTION _____________________________________________________

10

WIRING DIAGRAM _____________________________________________________________

11

GAS CONNECTION _____________________________________________________________

12

Manual shut-o valve

_________________________________________________________

12

Flexible connections __________________________________________________________

12

Pressure test-point stopper valve _______________________________________________

12

Pressure regulator ____________________________________________________________

13

INSTALLATION ________________________________________________________________

14

Unpackaging the range

________________________________________________________

14

Removing the oven door _______________________________________________________

14

Installing the legs _____________________________________________________________

15

Installing the worktop frontguard ________________________________________________

15

Installing the island trim _______________________________________________________

16

Installing backguard (optional) __________________________________________________

16

INSTALLING THE ANTI-TIP DEVICES ______________________________________________

17

Anti-tip brackets ______________________________________________________________

17

Anti-tilt chain ________________________________________________________________

17

GAS CONVERSION _____________________________________________________________

18

INSTALLATION CHECKLIST ______________________________________________________

22

FINAL PREPARATION ___________________________________________________________

22

BERTAZZONI SERVICE

_________________________________________________________

23

2

/ Models

Models

Models

MAST304GASXV

PROF304GASART

MAST304GASXVLP

PROF304GASBIT

MAST305GASBIE

PROF304GASGIT

MAST305GASNEE

PROF304GASNET

MAST305GASXE

PROF304GASROT

MAST305GASXELP

PROF304GASXT

MAST365GASBIE

PROF304GASXTLP

MAST365GASNEE

PROF366GASART

MAST365GASXE

PROF366GASBIT

MAST365GASXELP

PROF366GASGIT

MAST366GASXT

PROF366GASNET

MAST366GASXTLP

PROF366GASROT

MAST486GGASBIE

PROF366GASXT

MAST486GGASNEE

PROF366GASXTLP

MAST486GGASXE

PROF486GGASART

MAST486GGASXELP

PROF486GGASBIT

MAST486GGASXT

PROF486GGASGIT

MAST486GGASXTLP

PROF486GGASNET

 

PROF486GGASROT

 

PROF486GGASXT

 

PROF486GGASXTLP

3

/ Warnings

WARNINGS

To ensure proper and safe operation, the appliance must be properly installed and grounded by a qualifi ed technician. DO NOT attempt to adjust, repair, service, or replace any part of your appliance unless it is specifi cally recommended in this manual.All other servicing should be referred to a qualifi ed servicer. Have the installer show you the location of the gas shuto valve and how to shut it o in an emergency. A certifi ed technician is required for any adjustments or conversions to Natural or LP gas.

FOR THE INSTALLER: Before installing the Bertazzoni appliance, please read these instructions carefully. This appliance shall be installed in accordance with the manufacturer’s installation instructions. Leave these instructions with the owner, who should save them for local inspector’s use and for future reference. DO NOT remove permanently a xed labels, warnings, or plates from product. This may void the warranty.

Installation must conform with all local codes. In

United States: installation must conform with the National Fuel Gas Code ANSI Z223.1 INFPA54

Massachusetts: All gas products must be installed by a “Massachusetts” licensed plumber or gasfi tter. A “T” type handle manual valve must be installed in the gas supply line to the appliance.

Canada: Installation must be in accordance with the current CAN/CGA B149.1 & 2 Gas Installation codes and/or local codes. Electri-

cal installation must be in accordance with the current CSA C22.1 Canadian Electrical Codesthe absence of codes:

Part 1 and/or local codes.

This range is NOT designed for installation in manufactured (mobile) homes or recreational park trailers.

DO NOT install this range outdoors.

This appliance must be properly grounded. Grounding reduces the risk of electric shock by providing a safe pathway for electric current in the event of a short circuit.

Warning!

To avoid risk of property damage, personal injury or death; follow information in this manual exactly to prevent a fi re or explosion.

Warning!

To avoid risk of property damage, personal injury or death; follow information in this manual exactly to prevent a fi re or explosion. DO NOT store or use gasoline or other fl ammable vapors and liquids nearbythis or any appliance.

WHAT TO DO IF YOU SMELL GAS: Do not light any appliance. Do not touch any electrical switch. Do not use any phone in your building. Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions. If you cannot reach your gas supplier, call the fire department.

NOTE: Installation and service must be performed by a qualifi ed installer, service agency or the gas supplier.

DANGER!!! ELECTRIC SHOCK HAZARD!!!

To avoid risk of electrical shock, personal injury or death, verify that the appliance has been properly grounded in accordance with local codes or in absence of codes, with the National Electrical Code (NEC). ANSI/NFPA 70latest edition.

DANGER!!! GAS LEAK HAZARD!!!

To avoid risk of personal injury or death, leak-te- sting of the appliance must be conducted according to the manufacturer’s instructions. Before placing appliance in operation, always check for gas leaks with water and soap solution.

DO NOT USE AN OPEN FLAME TO CHECK FOR GAS LEAKS.

Warning - tipping hazard

Children and adults can tip over the range if it has not been secured.This may lead to fatal injuries. To reduce the risk of the appliance tipping, it must be secured and connected using the anti-tip device according to the installation instructions.

4

/ Warnings

Re-engage the anti-tip device if the range is moved. Do not operate the range without te anti-tipdevice in place and engaged. Do not use the range if the anti-tip device has not been properly installed and engaged. See installation instructions for details.

Failure to observe the information contained in the installation instructions can lead to serious or fatal injuries for children and adults.

5

/ Data rating label / Before installation

DATA RATING LABEL

The data rating label shows the model and serial number of the range. It is located under the control panel and in the last page of this manual.

BEFORE INSTALLATION

This appliance shall only be installed by an authorized professional.

This appliance shall be installed in accordance with the manufacturer’s installation instructions.

This appliance must be installed in accordance with the norms & standards of the country where it will be installed.

The installation of this appliance must conform to local codes and ordinances. In the absence of local codes, Installations must conforms to American National Standards, National Fuel Gas Code ANSI Z223.1 – latest edition/NFPA 54 or B149.1.

The appliance, when installed, must be electrically grounded in accordance with local codes or, in the absence of local codes, with the National Electrical Code, ANSI/NFPA 70.

If local codes permit, a fl exible metal appliance connection conduit with the newAGAor CGAcertifi ed design, max. 5 feet (1,5 m) long, ½” I.D. is recommended for connecting this appliance to the gas supply line. Do not bend or damage the fl exible connector when moving the appliance.

This appliance must be used with the pressure regulator provided.

The regulator shall be properly installed in order to be accessible when the appliance is installed in its

nal location. The pressure regulator must be set for the type of gas to be used. The pressure regulator has ½” female pipe thread. The appropriate

tting must be determined based on the size of your gas supply line, the fl exible metal connector and the shuto valve.

The appliance must be isolated from the gas supply piping system by closing its individual manual shuto valve during any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 PSI (13,8” w.c. or 3,5 kPa).

All opening and holes in the wall and fl oor, back and under the appliance shall be sealed before installation of the appliance.

A manual valve shall be installed in an accessible location in the gas line external to the appliance for the purpose of turning on or shutting o gas to the appliance.

Type of gas

This range can be used with Natural or LP/Propane gas. The range is shipped from the factory for use with the gas indicated on the rating label positioned on the lower face of the control panel and in the last page of this manual.Astep by step conversion procedure is also included in this manual and in each conversion kit.

Gas pressure

The maximum inlet gas supply pressure incoming to the gas appliance pressure regulator is 1/2 PSI (13,8’’ w.c. or 3,5 kPa). The minimum gas supply pressure for checking the regulator setting shall be at least 1“ w.c. (249 Pa) above the inlet speci- fi ed manifold pressure to the appliance; this operating pressure is 4” w.c. (1.00 kPa) for Natural Gas and 11” w.c. (2.75 kPa) for LP Gas.

Room ventilation

An exhaust fan may be used with the appliance; in each case it shall be installed in conformity with the appropriate national and local standards. Exhaust hood operation may a ect other vented appliances; in each case it shall be installed in conformity with the appropriate national and local standards.

Warning

This appliance should not be installed with a ventilation system that directs air in a downward direction toward the range. This type of ventilation system may cause ignition and combustion problems with the appliance resulting in personal injury, property damage, or unintended operation. Ventilating systems that direct the air upwards do not have any restriction.

Do not use aerosol sprays in the vicinity of this appliance while it is in operation.

6

/ Ventilation preparation / Specifi cations

VENTILATION PREPARATION

This range will best perform when installed with Bertazzoni exhaust hoods. These hoods have been designed to work in conjunction with the Bertazzoni range and have the same fi nish for a perfect look.

Before installation of the exhaust hood, consult local or regional building and installation codes for additional specifi c clearance requirements.

Refer to the range hood installation instructions provided by the manufacturer for additional information.

Select Hood and Blower Models:

For wall installations, the hood should be equal or larger width than the range. Where space permits, a hood larger than the range may be desirable for improved ventilation performance.

For island installations, the hood width should overhang the range by a minimum of 3” (76 mm) on each side.

Hood Placement:

For best removal of smoke and odors, the lower edge of the hood should be installed between 25 1/2” (65 cm) and 31 1/2” (80 cm) above the range cooking surface.

If the hood contains any combustible materials (i.e. a wood covering), it must be installed at a minimum of 36” (914 mm) above the cooking surface.

Consider Make-Up Air:

Due to the high volume of ventilation air, a source of outside replacement air is recommended. This is particularly important for tightly sealed and insulated homes. A qualifi ed heating and ventilating contractor should be consulted.

SPECIFICATIONS

A

30’’ 36’’ 48’’

7

/ Specifi cations

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Pressure

 

Max Rate

 

 

Min Rate

 

By-pass

 

 

 

Burner

 

 

Injector

 

Gas

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

diam.[mm]

Type

[i.w.c.]

[BTU/h] [W]

[BTU/h]

[W]

diam.[mm]

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Auxiliary

0,90

 

NG

4’’

3500

1025

900

264

Regulated

 

 

 

 

 

0,54

 

LP (Propane)

11’’

3500

1025

900

264

0,29

 

 

 

 

Semi-rapid

1,18

 

NG

4’’

5900

1728

1500

439

Regulated

 

 

 

 

 

0,70

 

LP (Propane)

11’’

5900

1728

1500

439

0,36

 

 

 

 

Rapid

1,55

 

NG

4’’

10400

3046

2500

732

Regulated

 

 

 

 

 

0,92

 

LP (Propane)

11’’

10400

3046

2500

732

0,47

 

 

 

 

Dual burner

0,80+2,10

NG

4’’

19000

5567

1300

381

Regulated

 

 

 

 

 

0,50+1,20

LP (Propane)

11’’

19000

5567

1300

381

0,34/0,65

 

 

 

MAIN oven

1,85

 

NG

4’’

14500

4248

3500

1025

Regulated

 

 

30’’/48’’

1,10

 

LP (Propane)

11’’

14500

4248

3500

1025

0,57

 

 

 

 

Broiler

1,70

 

NG

4’’

12000

3516

only max

only max

No by-pass

 

 

30’’/48’’

0,98

 

LP (Propane)

11’’

12000

3516

only max

only max

No by-pass

 

 

Oven 36’’

2,00

 

NG

4’’

17000

4981

4100

1201

Regulated

 

 

 

 

 

1,16

 

LP (Propane)

11’’

16000

4686

4100

1201

0,62

 

 

 

 

Broiler 36’’

1,60

 

NG

4’’

11000

3222

only max

only max

No by-pass

 

 

 

 

 

 

0,98

 

LP (Propane)

11’’

11500

3369

only max

only max

No by-pass

 

 

AUX. Oven

1,25

 

NG

4’’

7000

2051

2400

703

Regulated

 

 

 

48’’

0,75

 

LP (Propane)

11’’

7000

2051

2400

703

0,49

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

See use and care manual for the layout of the surface burners of your range

8

/ Clearence dimensions

CLEARENCE DIMENSIONS

Installation adjacent to kitchen cabinets

This range may be installed directly adjacent to existing countertop high cabinets (36” or 91.5 cm from the fl oor).

For the best look, the worktop should be level with the cabinet countertop. This can be accomplished by raising the unit using the adjustment spindles on the legs.

ATTENTION: the range CANNOT be installed directly adjacent to kitchen walls, tall cabinets, tall appliances, or other vertical surfaces above 36” (91.4 cm) high. The minimum side clearance in such cases is 6” (15.2 cm).

Wall cabinets with minimum side clearance must be installed 18” (45.7 cm) above the countertop with countertop height between 35 ½” (90.2 cm) and 37 ¼” (94.6 cm). The maximum depth of wall cabinets above the range shall be 13” (33.0 cm).

Cabinet

A30’’ (76,2 cm)

B36’’ (91,5 cm) hood with combustible materials

C13’’ (33,0 cm)

D18’’ (45,7 cm)

E35’’ 1/2(90,2 cm) / 37” 1/4 (94,6 cm)

F6’ (15,2 cm)

G12”(30,50 cm)

Metal hood

A30’’ (76,2 cm)

B25 1/2’’(65 cm) and 31 1/2’’ (80 cm)

C13’’ (33,0 cm)

D18’’ (45,7 cm)

E35’’ 1/2(90,2 cm) / 37” 1/4 (94,6 cm)

F6’ (15,2 cm)

G12”(30,50 cm)

H1” 9/16(4 cm)

Shaded area behind range indicates minimum clearance to combustible surfaces, combustible materials cannot be located within this area.

12” (305 mm) min. to combustible surface with Flush Island Trim

For Flush Island installations, counter surface should have a cantilever edge meeting the back section of the Flush Island Trim accessory.

As defi ned in the “National Fuel Gas Code” (ANSI Z223.1, Current Edition).

Clearances from non-combustible materials are not part of the ANSI Z21.1

scope and are not certifi ed by CSA. Clearances of less than 12” (305 mm)

must be approved by the local codes and/or by the local authority having jurisdiction.

9

/ Installation requirements / Electrical connection

INSTALLATION REQUIREMENTS

ELECTRICAL

Aproperly-groundedhorizontally-mountedelectri- cal receptacle should be installed no higher than 3” (7.6 cm) above the fl oor, no less than 2” (5 cm) and no more than 8” (20,3 cm) from the left side (facing product).

Check all local code requirements.

GAS

An agency-approved, properly-sized manual shut-o valve should be installed no higher than 3” (7.6 cm) above the fl oor and no less than 2” (5 cm) and no more than 8” (20.3 cm) from the right side (facing product).

Toconnectgasbetweenshut-o valveandregulator, use agency-approved, properly sized fl exible or rigid pipe. Check all local code requirements.

installation area for the connection

ELECTRICAL CONNECTION

Warning!

ELECTRICAL SHOCK HAZARD

Disconnect electrical power at the circuit breaker box or fuse box before installing the appliance.

Provide appropriate ground for the appliance. Use copper conductors only.

Failure to follow these instructions could result in serious injury or death.

This unit is manufactured for a polarized, grounded 120 volt/60 Hz, 16 amp system.

Electric power consumption is about 300 W for 30” and 36”, 1200W for 48”

The minimum of 102 VAC is required for proper operation of gas ignition systems.

The circuit must be grounded and properly polarized.

The unit is equipped with a SJT power cord and a NEMA 5-15P plug. In case of replacement, the power cord shall be replaced with one of the same type, size and length.

Electrical grounding

This appliance is equipped with a three-prong plug for your protection against shock hazard and should be plugged directly into a properly grounded socket. Do not cut or remove the grounding prong from this plug.

Caution

Label all wires prior to disconnecting when servicing controls. Wiring errors can cause improper and dangerous operation.

Verify proper operation after servicing.

10

Bertazzoni PROF486GGASXTLP, BERAMW100 Installation manual

/ Wiring diagram

WIRING DIAGRAM

The electric wiring diagrams and schematics are attached behind the range, and should not be removed except by a service technician, then replaced after service.

MAGNET UNITS &

 

 

 

 

 

 

COLOURS

TERMOCOUPLES

 

 

 

 

 

 

Simb.

Description

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

n

 

 

r

Red

J12 J11J10 J9 J8 J7

IGN

 

n

 

 

gr

Green (earth)

 

 

 

 

J13

 

T-Z

 

 

 

 

 

 

v

Violet

 

 

 

 

 

 

 

 

 

 

 

 

 

 

bi

 

 

 

 

 

 

 

 

 

 

 

 

 

 

a

Orange

J1

J2

J3

J4

J5

J6

 

 

 

 

 

 

 

 

 

 

 

n

Black (line)

 

 

 

 

 

 

G

 

 

 

Comm.2+0

 

 

 

 

 

 

 

r

 

bi

White (neutral)

 

 

 

 

 

 

 

 

 

1

1

 

 

 

 

 

 

 

 

 

 

 

 

P

2

 

 

 

 

 

 

 

 

gv

KI

 

 

2

 

a

 

 

 

 

 

 

 

bi

3

a

 

 

 

 

 

 

n

P

 

 

 

 

 

 

 

 

 

 

3

4

 

 

 

 

 

 

 

 

 

 

 

 

P

 

 

 

 

 

 

 

 

 

 

 

 

4

 

 

 

 

 

 

 

 

 

 

 

 

 

P

 

 

 

IGN

 

 

 

 

 

n

 

 

 

COM

 

ILF

 

 

v

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

bi

m

 

 

LF

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

MVT

 

 

 

 

 

 

 

 

 

 

 

 

 

 

gr

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

INV

 

 

 

r

 

LF

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

r

 

 

 

 

 

 

 

 

gv

 

 

 

gv

 

LEGENDA

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Simb.

Description

 

 

 

 

 

 

 

 

 

 

 

IGN

Ignition Micro switches

 

 

 

 

 

 

 

 

 

 

 

INV

Fan Oven Interlock

 

 

 

 

 

 

 

 

 

 

 

 

COM

Oven Function Selector

 

 

 

 

 

 

 

 

 

 

 

G

Spark Generator

 

 

 

 

 

 

MV

MV

 

 

 

 

ILF

Oven lamp switch

 

 

 

 

 

 

 

 

bi

GV

KI

Termal switch

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

LF

Oven lamp

 

 

 

 

 

 

 

 

 

 

n

 

M

Terminal Block

 

 

 

 

 

 

 

 

 

 

 

MV

Fan motor

 

 

 

 

 

 

 

 

 

 

 

M

 

 

 

 

 

 

 

 

 

 

L N

MVT

Cooling fan motor

 

3071063

 

 

 

 

 

 

 

 

 

T-Z T-zero

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

MAGNET UNITS &

 

 

n

 

 

 

 

 

TERMOCOUPLES

IGN

n

 

 

GE

 

 

 

 

 

 

 

 

 

 

 

 

 

 

J12 J11J10 J9

J8

J7

 

 

bi

 

 

1

2 TSS

J13

 

T-Z

 

 

G

 

 

 

 

 

 

 

 

r

 

 

 

bi

 

 

J1

J2

J3

J4

J5

J6

 

 

 

 

bi

 

 

 

 

 

 

 

 

 

 

 

r

 

 

 

gv

 

 

 

 

 

 

 

 

 

S

 

 

 

 

 

 

 

 

 

 

 

r

r

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

IGN

IGN

 

 

 

 

 

 

 

 

 

 

 

 

right

left

 

v

 

 

COLOURS

 

 

 

 

 

 

bi

 

 

 

 

 

Simb.

Description

 

 

 

 

 

 

 

 

 

 

KI

r

Red

 

 

a

n

 

 

 

 

 

 

 

gr

Green (earth)

 

 

 

 

 

 

 

 

 

 

b

Blue

 

 

 

n

 

 

b

 

 

 

 

 

v

Violet

INV

 

n

 

a

 

 

 

 

 

 

 

 

ILF

 

 

 

 

 

 

a

Orange

 

 

right

 

 

 

 

 

 

 

 

n

Black (line)

 

 

 

 

 

 

 

 

 

 

 

 

bi

White (neutral)

 

 

RGR

 

LF

MVT

 

 

 

 

MVT

 

gv

 

 

 

 

 

 

 

 

 

 

 

 

 

 

right

 

 

 

 

 

 

 

 

 

 

 

right

 

 

 

 

left

 

 

 

 

 

 

a

 

 

 

 

 

 

 

 

 

bi

 

 

 

 

 

 

 

 

 

 

MV

MV

 

 

 

 

 

 

 

 

 

 

 

 

 

 

n

3071064

 

 

Comm.2+0

 

 

 

 

1

1

 

 

 

 

P

2

 

 

 

 

2

 

a

bi

 

3

 

 

P

 

a

 

 

3

4

 

 

 

 

P

 

 

 

 

4

 

 

 

 

 

P

 

 

 

 

 

COM

 

 

ILF

 

 

 

 

 

left

bi

 

 

 

 

LF

 

 

 

 

 

left

gv

 

 

 

 

 

 

 

 

r

r

LF

 

 

 

 

 

 

 

 

left

 

 

 

 

 

 

 

 

 

 

LEGENDA

 

 

gv

Simb.

 

Description

 

 

IGN

 

Ignition Micro switches

 

 

 

INV

 

Fan Oven Interlock

 

 

 

COM

 

Oven Function Selector

 

 

 

G

 

Spark Generator

 

 

 

GE

 

Griddle Thermostat

 

 

 

ILF

 

Oven lamp switch

 

 

 

KI

 

Termal switch

 

bi

GV

LF

 

Oven lamp

n

 

M

 

Terminal Block

 

 

MV

 

Fan motor

 

 

M

MVT

 

Cooling fan motor

L

N

RGR

 

Griddle element

 

 

 

TSS

 

Safety Thermostat

 

 

 

T-Z

 

T-zero

11

/ Gas connection

GAS CONNECTION

Warning!

DO NOT USE AN OPEN FLAME WHEN CHECKING FOR LEAKS!

Leak testing of the appliance shall be conducted according to the manufacturer’s instructions. Before placing the oven into operation, always check for leaks with soapy water solution or other acceptable method.

Checkforgasleakagewithsoapywatersolutionor other acceptable methods in all gas connections installed between inlet gas pipe of the appliance, gas regulator, till to the manual shut-o valve.

Allgasconnectionsmustcomplywithnationaland local codes. The gas supply line (service) must be the same size or greater than the inlet line of the appliance. This range uses a 1/2” NPT inlet (see drawing below for details of gas connection). On all pipe joints use appropriate sealant resistant to gas to joint the adapter to range manifold use only the blue gasket supplied.

If necessary, the appliance must be converted by the dealer, by a factory-trained professional or by a qualifi ed licensed plumber or gas service company.

Gas conversion is important for safe and e ective use of the appliance. It is the responsibility of the dealer and the owner of the range to perform the appropriate gas conversion following the directions of the manufacturer.

THE GAS CONVERSION PROCEDURE IS DESCRIBED IN THIS MANUAL AND IN THE PACKAGE CONTAINING THE CONVERSION NOZZLES SHIPPED WITH EVERY RANGE.

Please provide the service person with this manual before work is started on the range.

MANUAL SHUT-OFF VALVE

THIS VALVE IS NOT SHIPPED WITH THE APPLIANC AND MUST BE SUPPLIED BY THE INSTALLER.

The manual shut-o valve must be installed in the gas service line between the gas hook-up on the wall and the appliance inlet, in a position where it can be reached quickly in the event of an emergency.

In Massachusetts: A ‘T’ handle type manual gas valve must be installed in the gas supply line to this appliance.

FLEXIBLE CONNECTIONS

In case of installation with fl exible couplings and/ or quick-disconnect fi ttings, the installer must use a heavy-duty, AGA design-certifi ed commercial fl exible connector of at least 1/2” (1.3 cm) ID NPT (with suitable strain reliefs) in compliance with ANSI Z21.41 and Z21.69 standards.

In Massachusetts: The unit must be installed with a 36” (3-foot) long fl exible gas connector.

In Canada: use CAN 1-6.10-88 metal connectors for gas appliances and CAN 1-6.9 M79 quick disconnect device for use with gas fuel.

PRESSURE TEST-POINT STOPPER VALVE

To avoid gas leaks, the pressure test-point stopper valve and gasket supplied with the range must be installed on the gas fi tting at the back of the range according to the diagram below.

GAS PIPE

BASKET

GAS CONNECTION ADAPTOR 1/2’’NPT WITH PRESSURE TEST POINT 1/8’’ NPT (TO BE FIXED TOWARD EXTERNAL SIDE OF THE APPLIANCE)

PRESSURE TEST-POINT

STOPPER

12

/ Gas connection

PRESSURE REGULATOR

Since service pressure may fl uctuate with local demand, every gas cooking appliance must be equipped with a pressure regulator on the incoming service line for safe and e cient operation. The pressure regulator shipped with the appliance has two female threads ½” NPT. The regulator shallbeinstalledproperlyinordertobeaccessible when the appliance is installed in its fi nal position.

Manifold pressure should be checked with a manometer and comply with the values indicated below:

Natural gas 4.0” W.c.P. LP/Propane 11.0” W.C.P.

Incoming line pressure upstream from the regulator must be 1” W.c.P. higher than the manifold pressure in order to check the regulator.

The regulator used on this range can withstand a maximum input pressure of 1/2 PSI (13,8” w.c. or 3,5 kPa) If the line pressure exceeds that amount, a stepdown regulator is required.

The appliance, its individual shut-o valve, and the pressure regulator must be disconnected from the gas line during any pressure testing of that system at pressures in excess of 1/2 PSI (13,8” w.c. or 3,5 kPa).

The individuaL manual shut-o valve must be in the OFF position during any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 PSI (13,8” w.c. or 3,5 kPa).

Warning

Before carrying out any servicing operation disconnect the appliance from gas and electric supply and extra appliance from fi nal installation place in order to have access to the appliance for proper servicing intervention.

13

/ Installation

INSTALLATION

APPLIANCE INSTALLATION

Unpacking the range

Remove all packing materials from the shipping pallet but leave the adhesive-backed foam layer over brushed-metal surfaces to protect it from scratches until the range is installed in its fi nalposition. Only the fi lm on the side panels should be removed before inserting the range between the cabinets.

Examine the appliance after unpacking it. In the event of transport damage, do not plug it. Take pictures of the damage and report it immediately to the freight forwarder.

Remove the oven door(s). This will reduce the weight of the range.

Thegrates,griddleplate,burnercaps,andoven racks should be removed to facilitate handling.

Before moving the range, protect the fl oor to prevent damage.

REMOVING THE OVEN DOOR

Prepare the door for removal. Flip up the locking clamps on each door hinge. Slowly shut the door until the protruding clamps stop the movement.

Pull oven door upwards and remove.

Do not lift or carry the oven door by its handle!

This may damage the hinges.

1

2

3

14

/ Installation

INSTALLING THE LEGS

Bertazzoni ranges must be used only with the legs properly installed.

Four height-adjustable legs are supplied with the range in the polysterene container situated over the appliance.

Before installing the legs, position the appliance near its fi nal location as the legs are not suitable for moving the appliance over long distances.

After unpacking the range, raise it enough to insert the legs in the appropriate receptacles situated on the lower part of the appliance. Lower the range gently to keep any undue strain from legs and mounting hardware. If possible use a pallet or lift jack instead of tilting the unit.

Adjust leg height to the desired level by twisting the inside portion of the leg assembly until the proper height is reached. Check with a level that the cooktop is perfectly level.

1

2

3

4

INSTALLING THE WORKTOP FRONTGUARD

To increase the clearance between the front edge of the worktop and the burners it is possible to install the worktop frontguard shipped with the appliance.

Locate the two fi xing holes on the end of the frontguard

Locate the two fi xing holes in the bottom side of the worktop

Fix the frontguard with the 2 supplied screwTo install the front guard,

15

+ 33 hidden pages