0 to 48
Months
Carrying Capacity
up to 20 kg
Babyhug Merlino Cot Bed
Style Code : NUBF020
baby furniture
2 in 1 Cot Bed
Please read the instructions carefully before use and keep this manual for future reference.
3 Level Adjustable Base Height Sturdy Frame
Elegant Look
Assembly Instructions
Contents:
1a Head Board : 1
1b Foot Board : 1
2a Front Side : 1
2b Back Side : 1
3 Base : 1
M6*90 mm Bolts : 8
M6*60 mm Bolts : 8
Barrel Nut : 16
Plastic Washer : 16
Allen Key : 1
1a
2b
1b
3
2a
A B C D E
Barrel NutM6x90M6x60 Plastic Washer Allen Key
X1X8 X16 X16X8
gure 1
1b
1a
2b
Cot Bed Mode :
Step 1:
As shown in gure 1, Connect the head
and foot boards with the back side of the
cot with bolt (M6*60mm), washer and
barrel nut. Insert the bolts part way to stop
the setup from moving.
1a
gure 2
gure 3
1b
1b
2b
2b
2a
1a
Step 2:
As shown in gure 2, insert two barrel nuts
into the holes in one corner of the base
and align the slots with the bolts (M6*90
mm).Once aligned, screw the bolts and
plastic washer into the barrel nuts, but do
3
not fully tighten at this stage. Repeat for
the other corners.
Step 3:
As shown in gure 3, attach the
front side to both head and foot
boards using one bolt (M6*60 mm),
3
plastic washer and one barrel nut
at each corner. Finally fully tighten
the side and base bolts.
gure 4
1b
gure 5
1b
1a
Bed Mode
Step 1:
1b
1a
Dismantle the cot bed carefully and place
all parts to one side. Separate the upper
and lower parts of both head and foot
boards as shown in gure 4 (Note: Any part
not used for bed mode would be needed
for other modes when converting. So store
all parts safely)
1a
Step 2:
As shown in gure 5, insert two barrel nuts
with plastic washers into the holes in one
3
corner of the base and align the slots with
the bolts. Once aligned, screw the bolts
into the barrel nuts, but do not fully
tighten at this stage.
Step 3:
Repeat above steps for the other corners
and fully tighten all the bolts.
Safety Warning:
• Be aware of the risk of open re and other sources of strong heat in the near vicinity of the child’s cot or bed
• Do not use the child’s cot or bed if any part is broken, torn or missing
• Do not leave anything in the cot that could present a danger of suffocation or strangulation
• Do not use more than one mattress in the cot
• In cot mode 3 base height positions are possible. The lowest position is the safest and should always be used as
soon as baby is old enough to sit up
• While at the lowest base position, ensure that the surface of the mattress and the upper edge of the cot frame
are at least 50 cm apart
• While at highest base position, ensure that the surface of the mattress and the upper edge of the cot frame are
at least 20 cm apart
• The cot bed is suitable for a mattress of 140 cm in length and 70 cm in width
• To prevent injury from falling, when the child is able to climb out of the cot, the cot should no longer be used for
that child. The cot should be converted to a bed
• The safety of the cot could be adversely affected by tting ammable drapes
• The cot should be placed either tight to any wall or have a gap of 30 cm between the wall and the side of the bed
• The bed should be carefully dismantled for storage or transportation
Care:
• Regularly check the tightness of bolts and tighten as necessary
• Check for damage which could render your cot or cot bed unsafe or cause splinters
• To clean, use a soft cloth, avoiding the use of strong detergents or abrasives
• An occasional light application of a wax polish will help maintain a good appearance
Imported & Marketed By
Brainbees Solutions Pvt. Ltd.
Corporate & Registered Office Address:
Rajashree Business Park, Plot No: 114,
Survey No. 338, Tadiwala Road,
Near Sohrab Hall, Pune 411 001
Customer Care :
020-30556310
customercare@brainbees.com
Made in PRC
Loading...