AT&T 1445 User Manual.pdf

2.12 Mb
Loading...

91-5596-30-00_att1445manual_r0APR0104.qxd 1950/2/13 ⁄U⁄¨ 07:21 Page 1

User Manual (Part 2)

2.4 GHz Cordless

Telephone 1445/1145

with Caller ID & CallWaiting

91-5596-30-00_att1445manual_r0APR0104.qxd 1950/2/13 ⁄U⁄¨ 07:21 Page 2

charge the battery before

See page 7

You must install and

STOP! for easy instructions

using the telephone

For customer service or product

Please also read

information, visit our web site at

Important Product Information

www.telephones.att.com

Enclosed in product package

or call 1-800-222-3111

 

CAUTION: To reduce the risk of fire or injury to persons or damage to the telephone, read and follow these instructions carefully:

Use only Replacement Battery 2422 (SKU# 23402).

Do not dispose of the battery in a fire. Like other batteries of this type, it could explode if burned. Check with local codes for special disposal instructions.

Do not open or mutilate the battery. Released electrolyte is corrosive and may cause damage to the eyes or skin. It may be toxic if swallowed.

Exercise care in handling batteries in order not to short the battery with conducting materials such as rings, bracelets, and keys. The battery or conductor may overheat and cause harm.

Charge the battery provided with or identified for use with this product only in accordance with the instructions and limitations specified in this manual.

Observe proper polarity orientation between the battery and battery charger.

Do not disassemble your telephone. There are no user-serviceable parts inside. Refer for servicing to qualified service personnel.

91-5596-30-00_att1445manual_r0APR0104.qxd 1950/2/13 ⁄U⁄¨ 07:21 Page 1

User Manual (Part 2)

2.4 GHz Cordless

Telephone 1445/1145

with Caller ID & CallWaiting

Table of contents

Getting Started

 

QUICK REFERENCE GUIDE..................

2

Parts checklist .......................................

4

Before you begin ..................................

5

Telephone base installation................

6

Battery installation & charging ..........

7

Wall mounting ......................................

8

Belt clip & optional headset..................

9

Telephone Operation

 

Customizing your telephone...........

10

Making and answering calls..............

12

Options while on calls ......................

13

Handset locator .................................

14

Caller ID Operation

 

Caller ID operation ...........................

20

To review yourcall log......................

21

To dial a call log entry ......................

22

To delete call log entries .................

23

To add entries to phone directory..

24

Appendix

 

Screen messages, lights and tones....

25

In case of difficulty .............................

27

Technical specifications ....................

28

Index .....................................................

29

Directory Dialing

 

Directory dialing ................................

15

Speed dialing........................................

16

Entering names into directory ........

17

Directory name search.....................

18

To move, edit or delete a listing ....

19

1

91-5596-30-00_att1445manual_r0APR0104.qxd 1950/2/13 ⁄U⁄¨ 07:21 Page 2

Getting Started

Quick reference guide

Handset

Incoming calls (see page 20)

NEW 00

OLD 27

0

8/12 10:06 AM

Hold

Press to place a call on hold. Press again to resume your call.

Low battery

Date and time

(see page 7)

(see page 10)

 

Select

Press to store a programming option (see page 10), or to store a directory entry in memory (see page 17).

Phone/Flash

Press to begin a call, then dial a number.

During a call, press to receive an incoming call, if Call Waiting is activated (see page 13).

Off

During a call, press to hang up.

During programming, press to stop without making changes.

^VVolume/Function

During a call, press ^Vto adjust listening volume.

While programming, press to change menu item or value (see page 10).

Press DIR when phone is not in use to display phone book entries (see page 18). While entering or modifying names, press to advance cursor.

Press CID when phone is not in use to display Caller ID information (see page 21). While entering numbers or letters, press to delete last character entered.

Chan/Delete

Prog

Redial/Pause

If call is noisy or unclear, press

Press to customize the telephone’s

to switch to a clearer channel.

operation (see page 10).

Press and hold to delete all

Caller ID entries.

Using the dial pad to enter letters (see page 17)

 

 

 

 

 

Press once to enter “A”

 

 

 

 

 

 

 

 

 

 

Press twice to enter “B”

 

 

 

 

 

 

 

 

 

 

Press 3 times to enter “C”

 

 

 

 

 

2

 

 

Press 4 times to enter “2”

Press to redial last number called.

While dialing or entering numbers into your phone directory, press to insert a 4-second dialing pause (see page 17).

2

91-5596-30-00_att1445manual_r0APR0104.qxd 1950/2/13 ⁄U⁄¨ 07:21 Page 3

Getting Started

Quick reference guide

Telephone Base

PAGE/ HANDSET LOCATOR

Press to locate handset if lost (see page 14).

IN USE/CHARGING

Steady: Handset battery is charging. Flashing: Phone is in use, or call is on hold.

NEW CALL

If you have Caller ID service: On when new calls have been received; off when all new Caller ID records have been reviewed (see page 20).

ANTENNA

Swivel fully upright for best results.

MESSAGE

Flashes when you have new voice mail (requires voice mail service from your local telephone company).

3

91-5596-30-00_att1445manual_r0APR0104.qxd 1950/2/13 ⁄U⁄¨ 07:21 Page 4

Getting Started

Parts checklist

Remember to save your sales receipt and original packaging in case you ever need to ship your telephone for warranty service. Check to make sure the telephone package includes the following:

Telephone base

Telephone handset

Power adapter

Battery pack

Belt clip

Long line cord

Short line cord

4

91-5596-30-00_att1445manual_r0APR0104.qxd 1950/2/13 ⁄U⁄¨ 07:21 Page 5

Getting Started

Before you begin

About Caller Identification

Caller ID with Call Waiting features in this telephone let you see who’s calling before you answer the phone, even when you’re on another call. These features require services provided by your local telephone company.

Contact your telephone service provider if:

You have both Caller ID and Call Waiting, but as separate services (you may need combined service)

You have only Caller ID service, or only Call Waiting service

You don’t subscribe to any Caller ID or Call Waiting services.

You can use this phone with regular Caller ID service, and you can use its other features without subscribing to either Caller ID or combined Caller ID with Call Waiting service. There may be fees for these services, and they may not be available in all areas.

Caller ID features will work only if both you and the caller are in areas offering Caller ID service, and if both telephone companies use compatible equipment.

See Caller ID Operation, beginning on page 20, for more details about how these features work.

Telephone operating range

This cordless telephone operates with the maximum power allowed by the Federal Communications Commission (FCC). Even so, this handset and base can communicate over only a certain distance — which can vary with the locations of the base and handset, the weather, and the construction of your home or office. For best performance, keep the base antenna fully upright.

If you receive a call while you are out of range, the handset might not ring — or if it does ring, the call might not connect when you press PHONE.

Move closer to the base, then press PHONE to answer the call.

If you move out of range during a phone conversation, you might hear noise or interference. To improve reception, move closer to the base.

If you move out of range without pressing OFF, your phone will be left “off the hook.” To hang up properly, walk back toward the telephone base, periodically pressing OFF until the call is disconnected.

5

91-5596-30-00_att1445manual_r0APR0104.qxd 1950/2/13 ⁄U⁄¨ 07:21 Page 6

Getting Started

Telephone base installation

Install the telephone base as shown below. Choose a location away from electronic equipment, such as personal computers, television sets or microwave ovens. Avoid excessive heat, cold, dust or moisture.

NOTE: Use only the power cord supplied with this product.

If you need a replacement, call 1 800 222–3111.

Be sure to use an electrical outlet not controlled by a wall switch.

Plug power cord

Plug long line cord

transformer into

into telephone jack

electrical outlet

 

6

91-5596-30-00_att1445manual_r0APR0104.qxd 1950/2/13 ⁄U⁄¨ 07:21 Page 7

Getting Started

Battery installation & charging

After installation, place the handset in the base and allow the battery to charge for 12 hours before use. You can keep the battery charged by returning the handset to the base after each use. When battery power is fully depleted, a full recharge takes about 8 hours.

NEW 00

OLD 27

0

8/12 10:06 AM

Press coin into slot on base of handset to release latch, then remove cover

Low battery indicator

Return handset to base to recharge when this symbol appears. (Handset will beep when battery is low.)

Plug in battery here

Place handset in base to charge for 12 hours before first use.

Charging light will be illuminated while battery is charging.

Rotate antenna to fully upright

position

To replace cover:

1 Insert tabs at top of cover into slots on base

2 Align tab at bottom of cover with slot in base, then press to click in place

7

91-5596-30-00_att1445manual_r0APR0104.qxd 1950/2/13 ⁄U⁄¨ 07:21 Page 8

Getting Started

Wall mounting

The telephone base can be installed on any standard wall-phone outlet as shown below. Choose a location away from electronic equipment, such as personal computers, television sets or microwave ovens. Avoid excessive heat, cold, dust or moisture.

Connect line cord and AC adapter as shown on page 6, then press notch and pull to open hinged wall mount

Swivel wall mount down and lock in place

Plug power cord transformer into electrical outlet

Plug short line cord into telephone jack

Press and slide down firmly so base is held securely on outlet mounting pegs

8

91-5596-30-00_att1445manual_r0APR0104.qxd 1950/2/13 ⁄U⁄¨ 07:21 Page 9

Getting Started

Belt clip & optional headset

Install belt clip as shown below if desired.

For hands-free telephone conversations, you can use any industry standard 2.5 mm headset (purchased separately). For best results use an AT&T 2.5 mm headset.

Snap belt clip into notches on side of handset. Rotate and pull to remove.

Plug 2.5 mm headset into jack on side of handset (beneath small rubber cap)

9

91-5596-30-00_att1445manual_r0APR0104.qxd 1950/2/13 ⁄U⁄¨ 07:21 Page 10

Press PROG

to begin programming

Press ^or Vto display features one by one

Press SELECT to modify a displayed feature

To stop at any time, press OFF

Telephone Operation

Customizing your telephone

Follow the steps below to program the telephone. To stop at any time, press OFF. If the phone rings, programming stops automatically so you may answer the call.

Choose ringer sound

1Press PROG to begin programming.

2Press ^until screen displays RINGER & setting.

3Press SELECT to change current setting:

RINGER: 1

Default setting: 1

4Press ^to display 1, 2, 3, 4 or OFF. You will hear a sample of each ringing type.

5Press SELECT to select displayed ringing type and exit.

Set handset display date and time

1Press PROG to begin programming.

2Press ^until screen displays DATE/TIME.

3Press SELECT to view or change date and time:

DATE/TIME

 

Default setting:

1/01 12:00

1/01 12:00 AM

AM

4Press ^or Vto change month, then press SELECT.

5Repeat Step 4 to set day, hour, minute, and AM/PM.

6Press SELECT to save selection and exit.

NOTE: You can choose to set the time manually, or you can allow it to be set automatically with incoming Caller ID information. The time will be set automatically only if you subscribe to Caller ID service provided by your local telephone company (see page 5).

10

91-5596-30-00_att1445manual_r0APR0104.qxd 1950/2/13 ⁄U⁄¨ 07:21 Page 11

Telephone Operation

Customizing your telephone

Choose dial mode

1Press PROG to begin programming.

2Press ^until screen displays DIAL MODE & setting.

3Press SELECT to change current setting:

DIAL MODE: TONE

Default setting: Tone

4Press ^to display TONE or PULSE.

5Press SELECT to select displayed dial mode and exit.

Choose language

1Press PROG to begin programming.

2Press ^until screen displays LANGUAGE & setting.

3Press SELECT to change current setting:

LANGUAGE: ENGLISH

Default setting: ENGLISH

4Press ^to display ENGLISH, ESPANOL or FRENCH.

5Press SELECT to select displayed language and exit.

Clear “Message Waiting” alert

1Press PROG to begin programming.

2Press ^until screen displays LIGHT OFF & setting.

3Press SELECT to change current setting:

LIGHT OFF: YES

4Press ^to display YES or NO.

5Press SELECT to select desired setting and exit.

11

91-5596-30-00_att1445manual_r0APR0104.qxd 1950/2/13 ⁄U⁄¨ 07:21 Page 12

Telephone Operation

Making and answering calls

Making and answering calls

To answer an incoming call, press any key except OFF. To make a call, press PHONE, then dial a number. Press OFF to hang up.

To preview numbers before dialing, enter numbers first, then press PHONE to dial. Press Vat any time to make corrections as you are entering numbers.

Speed dialing & directory dialing

To use speed dialing, press and hold a dial pad button (1-9) to display the number stored in that speed-dial location, then press PHONE to dial the number.

To use directory dialing, press DIR, scroll or search to find the number you want, then press PHONE to dial the number. (See pages 15-19 to enter, edit or search for listings in your phone directory.)

12345678901 the last number

press PHONE. To

. This will clear the redial memory and leave it blank.

Ring silencing

Press OFF while the phone is ringing to silence the ringer without disconnecting the call.

12

91-5596-30-00_att1445manual_r0APR0104.qxd 1950/2/13 ⁄U⁄¨ 07:21 Page 13

PAT JOHNSON * 908-555-0100

AM

VOLUME

Telephone Operation

Options while on calls

will (see options).

Call waiting

If you have Call Waiting service, you will hear a beep if someone calls while you are already on a call. Press PHONE to put your current call on hold and take the new call. You can press this button at any time to switch back and forth between calls.

Hold

Press HOLD to place a call on hold. Press HOLD again to resume the call.

To adjust listening volume

During a call you can press ^to increase or Vto decrease the listening volume.

If sound is unclear

If noise or static disrupts a call, press CHAN to scan for a clearer radio channel between handset and base.

Temporary tone dialing

If you have dial pulse (rotary) service, you can switch to touch tone dialing during a call by pressing *. This can be useful if you need to send tone signals for access to answering systems or long-distance services.

13

PAGE/HANDSET LOCATOR

91-5596-30-00_att1445manual_r0APR0104.qxd 1950/2/13 ⁄U⁄¨ 07:21 Page 14

Telephone Operation

Handset locator

Handset locator

If the handset is misplaced, press the PAGE/HANDSET LOCATOR button in the handset cradle on the base. The handset will beep for 60 seconds to help you find it. When the handset is found, press OFF to stop the beeping (or press the button on the base).

14

91-5596-30-00_att1445manual_r0APR0104.qxd 1950/2/13 ⁄U⁄¨ 07:21 Page 15

PAT JOHNSON 5550100

Directory Dialing

to

letters long. A convenient search feature can help you find and dial numbers quickly (see pages 16-19).

Speed dialing

The first nine memory locations (1 through 9) are reserved for numbers you dial frequently. These numbers can be dialed with two button presses (see next page).

Error tones

If all memory locations are in use, an error tone will sound when you attempt to enter a number. This means the memory is full, and you will not be able to store a new number until you delete an existing one.

15

91-5596-30-00_att1445manual_r0APR0104.qxd 1950/2/13 ⁄U⁄¨ 07:21 Page 16

1 PROG

DIRECTORY

2 ^

SPEED DIAL

3 SELECT

ENTER 1-9

ENTER NAME

01

(See Steps 3-7 on next page.)

Directory Dialing

Speed dialing

Numbers called most frequently can be stored in memory locations 1-9 and dialed with only two button presses.

You can enter 9 Speed Dial numbers up to 24 digits long. Each number is stored in a one-digit memory location (1-9).

To enter a Speed Dial number

1Press PROG to begin programming.

2Press ^ to display SPEED DIAL.

3Press SELECT.

4Press dial pad to choose memory location (1-9).

5Enter a name (up to 15 characters), then press

SELECT.

6Enter a telephone number (up to 24 digits), then press SELECT.

7Choose distinctive ringing (yes or no).

8Press PROG or SELECT to store the number. You will hear a confirmation tone.

To call a Speed Dial number

To use speed dialing, press and hold a dial pad button (1-9) to display the number and name stored in that speed-dial location, then press PHONE to dial the number.

NOTE: To view another Speed Dial number, Press "OFF". Follow the instruction "To call a Speed Dial Number" to display another Speed Dial number.

To change or delete a Speed Dial number

Press and hold a dial pad button (1-9) to display the entry you want. Press SELECT, then press ^until the option you want is displayed (see page 19).

16

91-5596-30-00_att1445manual_r0APR0104.qxd 1950/2/13 ⁄U⁄¨ 07:21 Page 17

1 PROG

DIRECTORY

2 SELECT

ENTER NAME

3

PAT JOHNSON_

4 SELECT

ENTER NUMBER

5

PAT JOHNSON 5550100

6 SELECT

DISTINCT RING? N 5550100

7 SELECT

NEW 00 OLD 07

1/01 12:00AM

Directory Dialing

Entering names into directory

To enter a name

Press dial pad buttons once for the first letter, twice for the second, three times for the third, as shown in the example below. To enter a number, continue pressing the button until the number appears.

Press once to enter “A” Press twice to enter “B”

2 Press 3 times to enter “C” Press 4 times to enter “2”

The cursor moves to the right when you press another dial pad button or the ^button. Press ^twice to enter a space. When the name is complete, press SELECT.

Options while entering names:

Press Vto erase letters if you make a mistake.

Press #repeatedly to enter an ampersand (&), apostrophe ('), comma (,) hyphen (-), period (.), or pound sign (#).

To enter a number

Use the dial pad to enter up to 24 digits. When the number is complete, press SELECT.

Options while entering numbers:

Press Vto erase numbers if you make a mistake.

Press REDIAL/PAUSE to enter a 4-second dialing pause.

To assign a distinctive ring

Press ^to select Y (yes) or N (no). If you choose Yes (and if you have Caller ID service), a different ringing style will alert you when this person calls.

Press SELECT to choose the option displayed (Y or N) and store this entry in the directory.

17

91-5596-30-00_att1445manual_r0APR0104.qxd 1950/2/13 ⁄U⁄¨ 07:21 Page 18

1 DIR

DIRECTORY

2 ^

ADAM 5551234

To display first listing

^ V

BETH 5554321

To scroll name by name

5

JOHN 5550123

To search alphabetically

PHONE

PHONE ON 5550123

To dial this number

Directory Dialing

Directory name search

Follow the steps at left to browse through the telephone directory, or search to find a specific entry. You can press OFF at any time to exit the directory.

To browse through the directory

To browse, press ^or Vto scroll through all listings one by one.

NOTE: "D" will appear in the display if the entry has been assigned distinctive ring (see page 17).

To search alphabetically

To shorten your search, use the telephone dial pad to enter the first letter of a name, then press ^to scroll forward until you find the name you want.

Press dial pad buttons once for the first letter, twice for the second, three times for the third, as shown below.

2........................

Find names beginning with “A”

22..............

Find names beginning with “B”

222......

Find names beginning with “C”

3........................

Find names beginning with “D”

33..............

Find names beginning with “E”

333......

Find names beginning with “F”

To call a displayed number

When you find the listing you want, press PHONE to dial. Or press SELECT to display other options (see next page).

18

91-5596-30-00_att1445manual_r0APR0104.qxd 1950/2/13 ⁄U⁄¨ 07:21 Page 19

1 DIR

DIRECTORY

2 ^

ADAM 5551234

3 SELECT

SPEED EDIT ERASE 5551234

^

SPEED EDIT ERASE 5551234

^

SPEED EDIT ERASE 5551234

Press SELECT to choose blinking option

Directory Dialing

To move, edit or delete a listing

When any listing is displayed, press SELECT to see options. Press ^or Vto highlight the option you want (blinking text), then press SELECT again to select it.

To move a listing

When SPEED is blinking, press SELECT, then dial a memory location (1-9) to transfer this entry to your Speed Dial directory.

To edit a listing

Press ^until EDIT is blinking, then press SELECT. You can change the name, number or distinct ring setting by following the steps described on page 17.

To delete a listing

Press ^until ERASE is blinking, then press SELECT to display a confirmation screen (ERASE NO YES).

To delete the listing, press ^to highlight YES, then press SELECT.

To abort the procedure and leave the listing intact, press Vto highlight NO, then press SELECT.

19

91-5596-30-00_att1445manual_r0APR0104.qxd 1950/2/13 ⁄U⁄¨ 07:21 Page 20

PAT JOHNSON * 908-555-0100 8/12 10:06AM NEW 03

Caller ID Operation

 

 

 

 

 

 

 

 

by your

 

 

 

 

 

 

 

 

caller will

 

 

 

 

Asterisk means same caller

 

 

 

 

has called more than once

Caller’s name

 

 

PAT JOHNSON

 

 

 

 

*

 

 

Caller’s phone number

 

908-555-0100

 

 

 

 

8/12 10:06AM NEW 03

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Date of call Time of call

Call number

 

 

 

 

 

 

and designation

 

 

 

 

 

 

(new or old)

Information about the last 90 incoming calls is stored in your call log. You can review the call log to find out who has called, return the call without dialing, or transfer the caller’s name and number into your phone directory.

Each incoming call is numbered. The most recent call is assigned the highest number. When the call log is full, the oldest call information is deleted to make room for new incoming call information.

If you answer a call before the information appears on the screen, it will not be saved in your call log.

Display screen messages

PRIVATE NAME Name of caller is not revealed at caller’s request.

PRIVATE CALLER Name and telephone number of caller are not revealed at caller’s request.

UNKNOWN NAME Your phone company is unable to determine caller’s name.

UNKNOWN CALLER Your phone company is unable to determine caller’s name and telephone number.

20

91-5596-30-00_att1445manual_r0APR0104.qxd 1950/2/13 ⁄U⁄¨ 07:21 Page 21

1 CID

PAT JOHNSON 908-555-0100

8/12 10:06AM NEW 03

2 V

CHRIS WILLIAMS 908-555-1234 8/12 9:53AM NEW 02

3 V

MARK CLAYTON 908-555-5678 8/12 9:12AM NEW 01

4 PHONE

PHONE ON 9085555678

To dial this number

Caller ID Operation

To review your call log

When the phone is not in use, press CID to display information about the most recent caller.

To review your call log

Press Vto scroll backward (display older calls) or ^ to scroll forward (display newer calls). The highest call number is the most recent call received.

To return a call

Press PHONE to call the person currently displayed (see page 22 for important dialing options).

Other options

Press SELECT at any Caller ID screen to see options (Dial or Program; see pages 22-24).

New and Old calls

Each screen of information is designated New until you have read it by reviewing the Call Log. Each screen you display is then designated Old.

21

91-5596-30-00_att1445manual_r0APR0104.qxd 1950/2/13 ⁄U⁄¨ 07:21 Page 22

1 CID

PAT JOHNSON 908-555-0100 8/12 10:06AM NEW 03

2 PHONE

PHONE ON 9085550100

Or

1 CID

PAT JOHNSON 908-555-0100 8/12 10:06AM NEW 03

2 #

PAT JOHNSON 555-0100

8/12 10:06AM NEW 03

3 PHONE

PHONE ON 5550100

Caller ID Operation

To dial a call log entry

When any Caller ID screen is displayed, press PHONE to dial the number exactly as it appears on the screen.

Dialing options

Caller ID numbers may appear with an area code that may not be required for local calls.

If the number displayed is not in the correct format, you can change how it is dialed. Press #repeatedly to see dialing options. With each button press a new option will be displayed. Press PHONE to dial when the number appears in the proper format for your area.

Example:

CID ......................

Number displayed as 908-555-0100

#........................

Number changes to 555-0100 (drops “1” + area code)

PHONE ................

Dials 555-0100

22

91-5596-30-00_att1445manual_r0APR0104.qxd 1950/2/13 ⁄U⁄¨ 07:21 Page 23

1 CID

PAT JOHNSON 908-555-0100

8/12 10:06AM NEW 03

2 V

CHRIS WILLIAMS 908-555-1234 8/12 9:53AM NEW 02

3 CHAN/DELETE

MARK CLAYTON 908-555-5678 8/12 9:12AM NEW 01

Or

NEW 00 OLD 27

1/01 12:00AM

1 CHAN/DELETE

ERASE ALL NO YES

2 ^

ERASE ALL NO YES

3 SELECT

NEW 00 OLD 00

1/01 12:00AM

Call log cleared

Caller ID Operation

To delete call log entries

To delete a single call log entry

Press CID, to display the first Caller ID listing. Use the up/down arrow keys to find the entry you want to delete, then press CHAN/DELETE. When the entry is deleted, the next oldest record is displayed.

To delete all call log entries

To clear your call log completely, press and hold CHAN/DELETE while the phone is idle (not in use). This will display a confirmation screen asking if you want to erase all entries in the Caller ID log. If you select YES, the call log will be cleared and the screen will return to normal standby display, showing no old or new calls.

23

91-5596-30-00_att1445manual_r0APR0104.qxd 1950/2/13 ⁄U⁄¨ 07:21 Page 24

1 CID

PAT JOHNSON 908-555-0100 8/12 10:06AM NEW 03

2 SELECT ^

DIAL PROGRAM 908-555-0100 8/12 10:06AM NEW 03

3 SELECT

PAT JOHNSON 9085550100

Edit name as desired

4 SELECT

PAT JOHNSON 9085550100

Edit number as desired

5 SELECT

DISTINCT RING? N 9085550100

6 SELECT

PAT JOHNSON 908-555-0100 8/12 10:06AM NEW 03

Entry added to phone directory

Caller ID Operation

To add entries to phone directory

When any Caller ID screen is displayed, follow the steps at left to enter it into your phone directory.

Both the caller’s name and telephone number will be entered as they appear in the call log. At steps 3-4, you can make any changes to the name or number by using the Vbutton to erase characters, or using the dial pad to enter new ones (see page 17 for instructions).

When the number is stored, the screen returns to the call log display. The entry copied to your phone directory remains in the call log until deleted.

24

91-5596-30-00_att1445manual_r0APR0104.qxd 1950/2/13 ⁄U⁄¨ 07:21 Page 25

Appendix

Display screen messages, lights and tones

Screen display messages

CONNECTING... The handset is waiting for a dial tone.

CONNECTING...

 

 

There is a call coming in.

 

 

 

 

 

handset locator has been activated

 

 

(handset beeps to help you locate it).

 

 

 

 

NEEDS RECHARGING

Handset battery is depleted. Place

 

 

handset in base to charge the battery.

 

 

 

 

 

 

 

BATTERY LOW

Handset battery is low. Place handset in

 

 

base to charge the battery.

 

 

 

 

PHONE ON

The handset is in use.

 

 

 

 

MESSAGES WAITING

You have new voice mail (requires voice

 

 

mail service from local telephone company)

 

 

 

 

RINGER OFF

The handset ringer is turned off.

 

 

 

 

HOLD

Current call is on hold.

 

 

 

 

SCANNING...

Handset is scanning for a clear channel

 

 

to improve sound quality.

 

 

 

 

NO CONNECT

Telephone is not connected. Check the

 

 

power jack.

 

 

 

25

91-5596-30-00_att1445manual_r0APR0104.qxd 1950/2/13 ⁄U⁄¨ 07:21 Page 26

Appendix

Display screen messages, lights and tones

Alert tones

 

 

 

“Beep-Beep...Beep-Beep...”

Handset battery is low. Place handset in

 

 

 

(Double beep every 5 seconds)

base to charge the battery.

 

 

 

 

 

 

 

 

“Beep-Beep-Beep”

Error tone (current operation has been

 

 

 

(3 quick beeps)

unsuccessful; try again).

 

 

 

 

 

 

 

 

“Beeeeeeeeep”

Confirm tone (current operation has been

 

 

 

(1 long beep)

successfully completed).

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Indicator lights

NEW CALL

If you have Caller ID service: On when new calls have been received; off when all new Caller ID records have been reviewed (see page 20).

IN USE/CHARGING

Steady: Handset battery is charging

Slow Flashing: Phone is in use

Fast Flashing: Call is on hold

MESSAGE

Flashes when you have new voice mail (requires voice mail service from your local telephone company).

26

91-5596-30-00_att1445manual_r0APR0104.qxd 1950/2/13 ⁄U⁄¨ 07:21 Page 27

Appendix

In case of difficulty

If you have difficulty with your phone, please try the suggestions below. For Customer Service, visit our web site at www.telephones.att.com, or call 1 800 222–3111.

Telephone does

• Make sure the battery pack is installed and charged correctly (see

not work at all

page 7).

 

• Make sure the AC adapter is plugged into an outlet not controlled by

 

a wall switch.

 

• Make sure the telephone line cord is plugged firmly into the base unit

 

and the modular jack.

 

• Make sure the base antenna is fully upright.

 

• If you have dial pulse telephone service, make sure the dial mode is

 

set to dial pulse (see page 11).

 

• If these suggestions do not work, unplug the base, remove and re-

 

insert the battery, then place the handset in the base to re-initialize.

 

 

Phone does not ring

Make sure the ringer is on (see page 10).

Make sure the telephone line cord and AC adapter are plugged in properly (see page 6).

Make sure the base antenna is fully upright.

Move the handset closer to the base.

You might have too many extension phones on your telephone line to allow all of them to ring. Try unplugging some of them.

If you hear noise or interference during a call

Make sure the base antenna is fully upright.

You may be out of range. Move closer to the base.

Press CHAN to select another channel. If noise is exceptionally loud, move closer to the base before changing channels.

Appliances plugged into the same circuit as the base can cause interference. Try moving the appliance or base to another outlet.

The layout of your home or office might be limiting the operating range. Try moving the base to another location, preferably on an upper floor.

If the buttons don’t work, try placing the handset in the base for at least 15 seconds.

Disconnect the base from the modular jack and plug in a corded telephone. If calls are still not clear, the problem is probably in your wiring or local service. Call your local telephone service company.

If you lose a call

• You were probably almost out of range. Move closer to the base

after changing

before changing channels. Before placing another call, set the hand-

channels

set in the base for at least 15 seconds.

27

91-5596-30-00_att1445manual_r0APR0104.qxd 1950/2/13 ⁄U⁄¨ 07:21 Page 28

Appendix

Technical specifications

RF Frequency Band

912.75 MHz — 917.10 MHz

(Handset to Base)

 

 

 

RF Frequency Band

2410.2 MHz — 2418.9 MHz

(Base to Handset)

 

 

 

Channels

30

 

 

Channel Spacing

300 KHz

 

 

Output Power

3 dBm

 

 

Sensitivity

-108 dBm

 

 

Modulation

FM

 

 

Operating Temperature

32°F — 122°F

 

0°C – 50°C

 

 

Base Unit Voltage

108 — 132 Vrms

(AC Voltage, 60Hz)

 

 

 

Base Unit Voltage

9 Vdc @300 mA

(AC Adapter Output)

 

 

 

Handset Voltage

3.1 — 4.2 Vdc @400 mAh

 

 

28

91-5596-30-00_att1445manual_r0APR0104.qxd 1950/2/13 ⁄U⁄¨ 07:21 Page 29

Appendix

Index

AC adapter, 6

Alert tones, 26

Answering calls, 12

Antenna, 7

Battery, 7

Belt clip, 9

Blocked caller/name, 20

Call logs, 21 Caller ID, 5, 20

add entries to phone directory, 24 delete entries, 23

dial entries, 22 Call waiting, 5, 13 Change channel, 13 CID, 20-24

Date/time, 10

Delete Call Log entries, 23 Delete directory entries, 19 Dialing,

directory dialing, 15 manual dialing, 12 speed dialing, 16

Directory dialing, delete entries, 23 dial number, 16, 19 display entries, 18 edit entries, 19

enter dialing pause, 17 enter names & numbers, 17 name search, 18

Display screen, 2 Distinctive ring, 17

Ending calls, 12

Erasing directory entries, 19

Error tones, 15

Flash, 13

Handset locator, 14

Hands-free use, 9

Headphone, 9

Hold, 13

Incoming call log, 21 Incoming calls, answering, 12 Indicator lights, 3, 26

Last number redial, 12 Locate handset, 14 Low battery, 7

Making calls, 12

Missed calls, 20

Names,

enter into directory, 17 search for, 18

Operating range, 5

Pause (while dialing), 17

Quick reference guide, 2-3

Receiving calls, 12

Recharging, 7

Redial, 12

Ring silencing, 12

Ring tone options, 10

Scrolling, 18

Search for name, 18

Speed dialing, 16

Technical specifications, 28 Time, 10

Tones,

change ringing tone, 10 send tones during call, 13 set dial mode, 11

Troubleshooting, 27

Unknown caller, 20

Volume controls, 2

29

91-5596-30-00_att1445manual_r0APR0104.qxd 1950/2/13 ⁄U⁄¨ 07:21 Page 30

www.telephones.att.com

Copyright © 2003 Advanced American Telephones. All Rights Reserved. AT&T and the Globe Design are trademarks of AT&T Corp.,

licensed to Advanced American Telephones. Printed in China. Issue 2 AT&T 04/01/04. 91-5596-30-00