ATMEL AT27BV1024-15VC, AT27BV1024-15JI, AT27BV1024-15JC, AT27BV1024-12VI, AT27BV1024-12VC Datasheet

...
0 (0)
ATMEL AT27BV1024-15VC, AT27BV1024-15JI, AT27BV1024-15JC, AT27BV1024-12VI, AT27BV1024-12VC Datasheet

AT27BV1024

Features

Fast Read Access Time - 90 ns

Dual Voltage Range Operation

Unregulated Battery Power Supply Range, 2.7V to 3.6V

±

Pin Compatible with JEDEC Standard AT27C1024

Low Power CMOS Operationor Standard 5V 10% Supply Range

20 μA max. (less than 1 μA typical) Standby for VCC = 3.6V

JEDEC Standard Surface Mount Packages 44-Lead PLCC

40-Lead TSOP (10 x 14mm)

High Reliability CMOS Technology 2,000V ESD Protection

200 mA Latchup Immunity

RapidProgramming Algorithm - 100 μs/word (typical)

CMOS and TTL Compatible Inputs and Outputs JEDEC Standard for LVTTL and LVBO

Integrated Product Identification Code

Commercial and Industrial Temperature Ranges29 mW max. Active at 5 MHz for VCC = 3.6V

Description

The AT27BV1024 is a high performance, low power, low voltage 1,048,576 bit onetime programmable read only memory (OTP EPROM) organized as 64K by 16 bits. It requires only one supply in the range of 2.7V to 3.6V in normal read mode operation. The by-16 organization makes this part ideal for portable and handheld 16 and 32 bit microprocessor based systems using either regulated or unregulated battery power.

(continued)

Pin Configurations

 

Pin Name

Function

 

A0 - A15

Addresses

 

O0 - O15

Outputs

 

 

 

 

 

 

CE

Chip Enable

 

 

 

 

 

 

OE

Output Enable

 

 

 

 

 

 

 

 

 

 

PGM

Program Strobe

 

 

 

 

 

 

NC

No Connect

 

 

 

 

 

Note: Both GND pins must be connected.

PLCC Top View

TSOP Top View

Type 1

Note: PLCC Package Pins 1 and 23 are DON’T CONNECT.

1 Megabit

(64K x 16) Unregulated

Battery-Voltage

High Speed OTP

CMOS EPROM

AT27BV1024

0631A

3-33

Description (Continued)

Atmel’s innovative design techniques provide fast speeds that rival 5V parts while keeping the low power consumption of a 3V supply. At VCC = 2.7V, any word can be accessed in less than 120 ns. With a typical power dissipation of only 18 mW at 5 MHz and VCC = 3V, the AT27BV1024 consumes less than one fifth the power of a standard 5V EPROM.

Standby mode supply current is typically less than 1 μA at 3V. The AT27BV1024 simplifies system design and stretches battery lifetime even further by eliminating the need for power supply regulation.

The AT27BV1024 is available in industry standard JEDEC-approved one-time programmable (OTP) plastic PLCC and TSOP packages. All devices feature two-line control (CE, OE) to give designers the flexibility to prevent bus contention.

The AT27BV1024 operating with VCC at 3.0V produces TTL level outputs that are compatible with standard TTL logic devices operating at VCC = 5.0V. At VCC = 2.7V, the part is compatible with JEDEC approved low voltage battery operation (LVBO) interface specifications. The device is also capable of standard 5-volt operation making it ideally suited for dual supply range systems or card products that are pluggable in both 3-volt and 5-volt hosts.

Atmel’s AT27BV1024 has additional features to ensure high quality and efficient production use. The RapidProgramming Algorithm reduces the time required to program the part and guarantees reliable programming. Programming time is typically only 100 μs/word. The Integrated Product Identification Code electronically identifies the device and manufacturer. This feature is used by industry standard programming equipment to select the proper programming algorithms and voltages. The AT27BV1024 programs exactly the same way as a standard 5V AT27C1024 and uses the same programming equipment.

System Considerations

Switching between active and standby conditions via the Chip Enable pin may produce transient voltage excursions. Unless accommodated by the system design, these transients may exceed data sheet limits, resulting in device non-conformance. At a minimum, a 0.1 μF high frequency, low inherent inductance, ceramic capacitor should be utilized for each device. This capacitor should be connected between the VCC and Ground terminals of the device, as close to the device as possible. Additionally, to stabilize the supply voltage level on printed circuit boards with large EPROM arrays, a 4.7 μF bulk electrolytic capacitor should be utilized, again connected between the VCC and Ground terminals. This capacitor should be positioned as close as possible to the point where the power supply is connected to the array.

3-34 AT27BV1024

AT27BV1024

Block Diagram

Absolute Maximum Ratings*

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Temperature Under Bias

-55°C to +125°C

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Storage Temperature

-65°C to +150°C

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Voltage on Any Pin with

 

(1)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Respect to Ground

-2.0V to +7.0V

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Voltage on A9 with

 

(1)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Respect to Ground

- 2.0V to +14.0V

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

VPP Supply Voltage with

 

(1)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

.......................Respect to Ground

- 2.0V to +14.0V

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

*NOTICE: Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.

Note: 1. Minimum voltage is -0.6V dc which may undershoot to -2.0V for pulses of less than 20 ns. Maximum output pin voltage is VCC + 0.75V dc which may overshoot to +7.0V for pulses of less than 20 ns.

Operating Modes

 

 

 

 

 

 

 

 

 

 

 

Mode \ Pin

CE

OE

PGM

Ai

VPP

VCC

Outputs

Read (2)

VIL

VIL

X (1)

Ai

X

VCC (2)

DOUT

Output Disable (2)

X

VIH

X

X

X

VCC (2)

High Z

Standby (2)

VIH

X

X

X

X (5)

VCC (2)

High Z

Rapid Program (3)

VIL

VIH

VIL

Ai

VPP

VCC (3)

DIN

PGM Verify (3)

VIL

VIL

VIH

Ai

VPP

VCC (3)

DOUT

PGM Inhibit (3)

VIH

X

X

X

VPP

VCC (3)

High Z

Product Identification (3, 5)

VIL

VIL

X

A9 = VH (4)

VCC

VCC (3)

Identification

A0 = VIH or VIL

 

 

 

 

 

 

 

A1 - A15 = VIL

 

 

Code

 

 

 

 

 

 

 

 

 

 

Notes: 1. X can be VIL or VIH.

2.Read, output disable, and standby modes require, 2.7V VCC 3.6V, or 4.5V VCC 5.5V.

3.Refer to Programming Characteristics. Programming modes require VCC = 6.5V.

4.VH = 12.0 ± 0.5V.

5.Two identifier words may be selected. All Ai inputs are held low (VIL), except A9 which is set to VH and A0

which is toggled low (VIL) to select the Manufacturer’s Identification word and high (VIH) to select the Device Code word.

3-35

Loading...
+ 6 hidden pages