ATMEL AT16373F-25XC, AT16373F-20YC, AT16373F-20XC, AT16373F-25YC Datasheet

0 (0)
ATMEL AT16373F-25XC, AT16373F-20YC, AT16373F-20XC, AT16373F-25YC Datasheet

AT16373

Features

Fastest Propagation Speeds in the Industry TPD (F grade) = 2.5 ns, TPD (G grade) = 2.0 ns

Maximum derating for capacitive loads 1.5ns/100 pF (F grade) and 1.1ns/100 pF (G grade)

Very low ground bounce < 0.6V @ VCC=5.00V, Ta=25°C

Excellent noise rejection

Typical output skew 0.25ns

Bus Hold circuitry to retain last active state during Tri-state

Available in SSOP and TSSOP packages

Description

Atmel’s AT16373 devices provide maximum speed in temporary data storage. They can be operated as either two separate 8 bit latches or as a single 16-bit latch by use of the output enable and the latch enable. The AT16373 has very low ground bounce and excellent input noise rejection, giving the user stable signals in a high speed environment. These devices can drive very large loads while operating in a high speed transparent mode.

Functional Block Diagram (1)

Note: 1. This 8-bit latch function is repeated a second time on each device.

Pin Configurations

 

 

 

 

 

 

 

 

SSOP/TSSOP

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Pin Names

Descriptions

1OE

 

1O1

 

1

2

 

48

47

 

1D1

1LE

 

 

 

 

 

 

 

1O2

 

3

46

 

1D2

GND

 

4

 

45

 

GND

 

 

 

 

 

 

 

 

 

 

Output Enable Input

1O3

 

5

 

44

 

1D3

 

 

 

1O4

 

6

 

43

 

1D4

 

 

 

 

 

 

xOE

 

 

 

VCC

 

7

42

 

VCC

(Active Low)

1O5

 

8

 

41

 

1D5

 

 

 

 

 

 

 

 

1O6

 

9

40

 

1D6

 

 

 

 

GND

 

10

 

39

 

GND

 

 

 

Latch Enable Inputs

 

 

 

 

 

 

 

 

xLE

1O7

 

11

38

 

1D7

1O8

 

12

 

37

 

1D8

 

 

 

 

 

 

(Active High)

2O1

 

13

 

36

 

2D1

2O2

 

14

 

35

 

2D2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

GND

2O3

 

15

16

 

34

33

 

2D3

GND

 

 

 

 

 

 

 

xDχ

Data Inputs

 

 

 

 

 

 

2O4

 

17

 

32

 

2D4

 

 

VCC

 

18

 

31

 

VCC

 

 

 

 

 

 

 

2O5

 

19

 

30

 

2D5

xOχ

Tri-State Outputs

 

 

 

2O6

 

20

 

29

 

2D6

 

 

 

GND

 

21

 

28

 

GND

 

 

 

 

 

 

2O7

 

22

 

27

 

2D7

 

 

 

 

 

 

 

 

 

 

 

2O8

 

23

 

26

 

2D8

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2OE

 

 

 

24

 

 

25

 

2LE

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Top View

AT16373 Fast Logic

16-Bit Transparent Latch

AT16373F

AT16373G

0756B

5-15

Function Table(1)

 

Inputs

 

 

 

Outputs

 

 

 

 

 

 

xDχ

xLE

 

 

 

xOχ

xOE

 

H

H

 

L

H

L

H

 

L

L

X

X

 

H

Z

 

 

 

 

 

 

Note: 1. X = Don’t Care, Z = High Impedance

Absolute Maximum Ratings*

Operating Temperature........................

0°C to +70°C

Storage Temperature......................

-65°C to +150°C

Voltage on any Pin

-2.0V to +7.0V(1)

with Respect to Ground ..................

Maximum Operating Voltage .............................

6.0V

5.0 Volt DC Characteristics

*NOTICE: Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.

Notes: 1. Minimum voltage is -0.6V dc which may undershoot to -2.0V for pulses of less than 20 ns. Maximum output pin voltage is VCC +0.75V dc which may overshoot to +7.0V for pulses of less than 20 ns.

Applicable over recommended operating range from Ta = 0°C to +70°C, V CC = +5.0V +/- 5% (unless otherwise noted)

 

 

 

 

 

 

Units

Symbol

Parameter

Test Conditions

Min

Typ

Max

 

 

 

 

 

 

 

 

ICC

Quiescent Power Supply

VCC = Max, VIN = 3.4V

 

0.8

1.2

mA

 

Current

 

 

 

 

 

 

 

 

 

 

 

 

VIH

Input High Voltage

 

2.0

 

 

V

 

 

 

 

 

 

 

VIL

Input Low Voltage

 

 

 

0.8

V

 

 

 

 

 

 

 

IIH

Input High Current

VIN = VCC

 

 

±15

μA

 

 

 

 

 

 

 

IIL

Input Low Current

VIN = GND

 

 

±15

μA

 

 

 

 

 

 

 

IOZ

Output Leakage Current

 

 

 

±10

μA

 

 

 

 

 

 

 

VOH(1)

Output High Voltage

VCC = 4.75V

2.7

 

 

V

 

F Grade only

IOH = -10 mA

 

 

 

 

 

 

 

 

 

 

 

VOH(2)

Output High Voltage

VCC = 4.75V

2.7

 

 

V

G Grade only

IOH = -12 mA

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

VOL

Output Low Voltage (F Grade)

IOL = 10 mA

 

 

0.55

V

 

 

 

 

 

 

 

VOL

Output Low Voltage (G Grade)

IOL = 12 mA

 

 

0.55

V

 

 

 

 

 

 

 

Note: 1. F grade: At VCC (max), the value of VOH(max) = 3.75V and at VCC(min), VOH(max) = 3.25V 2. G grade: At VCC (max), the value of VOH(max) = 3.75V and at VCC(min), VOH(max) = 3.35V

5-16

AT16373

 

 

 

Loading...
+ 4 hidden pages