Copyright Notice:
No part of this installation guide may be reproduced, transcribed, transmitted, or translated in any language, in any form or by any means, except duplication of documentation by the purchaser for backup purpose, without written consent of ASRock Inc.
Products and corporate names appearing in this guide may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners’ benefit, without intent to infringe.
Disclaimer:
Specifications and information contained in this guide are furnished for informational use only and subject to change without notice, and should not be constructed as a commitment by ASRock. ASRock assumes no responsibility for any errors or omissions that may appear in this guide.
With respect to the contents of this guide, ASRock does not provide warranty of any kind, either expressed or implied, including but not limited to the implied warranties or conditions of merchantability or fitness for a particular purpose. In no event shall ASRock, its directors, officers, employees, or agents be liable for any indirect, special, incidental, or consequential damages (including damages for loss of profits, loss of business, loss of data, interruption of business and the like), even if ASRock has been advised of the possibility of such damages arising from any defect or error in the guide or product.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1)this device may not cause harmful interference, and
(2)this device must accept any interference received, including interference that may cause undesired operation.
CALIFORNIA, USA ONLY
The Lithium battery adopted on this motherboard contains Perchlorate, a toxic substance controlled in Perchlorate Best Management Practices (BMP) regulations passed by the California Legislature. When you discard the Lithium battery in California, USA, please follow the related regulations in advance.
“Perchlorate Material-special handling may apply, see www.dtsc.ca.gov/hazardouswaste/perchlorate”
ASRock Website: http://www.asrock.com
Published February 2011
Copyright©2011 ASRock INC. All rights reserved.
1
ASRock H61DE/S3 Motherboard
English
2
Motherboard Layout |
|
|
|
|
|
|
|
|
|
||||||
|
|
|
|
|
|
1 |
2 |
3 |
4 |
|
5 |
6 |
|
|
|
|
|
|
|
|
|
21.8cm (8.6 in) |
|
|
|
|
|
|
|
|
|
|
Keyboard PS2 |
|
USB 2.0 |
|
Designed in Taipei |
|
|
|
|
|
|
|
|
||
|
|
T: USB0 |
|
|
CPU_FAN1 |
CPU_FAN2 |
|
|
|
|
|
|
|
||
|
|
|
B: USB1 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
ATX12V1 |
|
|
|
|
|
|
|
|
VGA1 |
DVI |
|
|
|
|
pin-240bit,(64module) |
pin-240bit,(64module) |
pin-240bit,(64module) |
pin-240bit,(64module) |
ATXPWR1 |
in) |
||
|
HDMI1 |
|
|
_CON1 |
|
|
|
DX10.1 DDR3 |
30.5cm(12.0 |
||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
7 |
|
USB 2.0 |
|
|
|
|
|
|
|
|
|
|
|
|
||
|
T: USB2 |
|
|
|
|
|
|
|
|
|
|
|
|
||
|
B: USB3 |
|
|
|
|
|
|
|
|
|
|
|
|
||
|
USB 2.0 |
|
|
|
|
|
|
A1 |
A2 |
B1 |
B2 |
|
|
||
|
T: USB4 |
|
Top: |
|
|
|
|
_ |
_ |
_ |
_ |
|
|
||
32 |
Center:Center: |
RJ-45 |
|
|
|
ChannelDual |
DDR3 |
DDR3 |
DDR3 |
DDR3 |
|
8 |
|||
MICIN Bottom: |
|
REARFRONTSPK |
BASSCTRLINEIN Top:Top: |
|
|
|
|
||||||||
|
B: USB5 |
|
|
|
|
|
|
|
|
|
|
|
|
||
|
SPDIF Optical Bottom: |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
PWR_FAN1 |
|
|
|
|
|
|
|
CHA_FAN2 |
|
31 |
|
|
|
|
|
CHA_FAN3 H61DE/S3 |
|
|
|
|
|
RoHS |
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
PHY |
PCIE1 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
LAN |
|
|
|
|
|
|
|
|
|
|
30 |
|
|
|
|
|
PCI Express 2.0 |
|
|
|
|
CMOS |
|
|||
|
|
|
|
|
|
|
|
|
|
|
|||||
|
|
|
|
|
|
|
|
ErP/EuP Ready |
|
Battery |
|
||||
29 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
HD_AUDIO1 |
|
|
|
|
|
|
|
|
32Mb |
9 |
|||
|
|
|
|
|
|
|
|
|
|
BIOS |
|||||
28 |
|
|
|
|
|
PCIE2 |
|
|
Intel |
|
|
||||
|
|
|
|
HDMI_SPDIF_1 |
|
|
|
|
|
|
|||||
1 |
|
|
|
1 |
|
|
|
H61 |
|
|
|
|
|||
27 |
|
|
|
|
|
|
|
|
|
|
CLRCMOS1 |
10 |
|||
|
|
|
AUDIO |
|
|
|
|
|
|
|
|
1 |
|
||
|
|
|
CODEC |
|
|
|
|
|
|
|
|
|
|||
26 |
|
|
|
|
|
PCIE3 |
|
|
|
|
|
|
|
|
11 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
12 |
|
|
|
|
|
|
PCI1 |
|
|
|
|
SATA2_0 |
SATA2_2 |
SATA3_1 |
13 |
|
|
|
|
Super |
|
|
USB6_7 |
|
|
|
|
|
14 |
|||
|
|
|
|
|
|
1 |
|
|
|
|
|
||||
|
|
|
|
I/O |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
USB8_9 |
|
|
|
|
|
15 |
25 |
|
|
|
|
|
|
|
|
1 |
|
|
|
|
|
|
|
|
|
|
|
PCI2 |
|
|
|
|
SATA2_1 |
SATA2_3 |
SATA3_2 |
|
||
|
|
|
|
|
|
|
|
CHA_FAN1 |
|
|
|
|
|
|
|
|
|
|
|
|
|
COM1 |
IR1 |
|
|
|
|
|
|
|
16 |
|
|
|
|
|
|
|
|
|
|
|
SPEAKER1 |
|
|
1 |
|
|
|
|
|
|
|
1 |
|
|
|
|
1 |
|
|
PANEL1 |
|
|
|
|
|
|
|
1 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
24 |
23 |
22 |
21 20 |
19 18 |
|
17 |
|
|
1 |
1155-Pin CPU Socket |
17 |
SATA2 Connector (SATA2_3, Blue) |
2 |
CPU Fan Connector (CPU_FAN1) |
18 |
Chassis Speaker Header (SPEAKER 1, White) |
3 |
CPU Fan Connector (CPU_FAN2) |
19 |
SATA2 Connector (SATA2_1, Blue) |
4 |
ATX 12V Power Connector (ATX12V1) |
20 |
Chassis Fan Connector (CHA_FAN1) |
5 |
2 x 240-pin DDR3 DIMM Slots |
21 |
USB 2.0 Header (USB8_9, Blue) |
|
(Dual Channel: DDR3_A1, DDR3_B1, Blue) |
22 |
USB 2.0 Header (USB6_7, Blue) |
6 |
2 x 240-pin DDR3 DIMM Slots |
23 |
Infrared Module Header (IR1) |
|
(Dual Channel: DDR3_A2, DDR3_B2, White) |
24 |
COM Port Header (COM1) |
7 |
ATX Power Connector (ATXPWR1) |
25 |
PCI Slots (PCI1-2) |
8 |
Chassis Fan Connector (CHA_FAN2) |
26 |
PCI Express 2.0 x1 Slot (PCIE3, White) |
9 |
32Mb SPI Flash |
27 |
PCI Express 2.0 x1 Slot (PCIE2, White) |
10 |
Clear CMOS Jumper (CLRCMOS1) |
28 |
Front Panel Audio Header |
11 |
Intel H61 Chipset |
|
(HD_AUDIO1, White) |
12 |
SATA2 Connector (SATA2_0, Blue) |
29 |
HDMI_SPDIF Header |
13 |
SATA2 Connector (SATA2_2, Blue) |
|
(HDMI_SPDIF1, White) |
14 |
SATA3 Connector (SATA3_1, White) |
30 |
PCI Express 2.0 x16 Slot (PCIE1, Blue) |
15 |
SATA3 Connector (SATA3_2, White) |
31 |
Chassis Fan Connector (CHA_FAN3) |
16 |
System Panel Header (PANEL1, White) |
32 |
Power Fan Connector (PWR_FAN1) |
ASRock H61DE/S3 Motherboard
I/O Panel
|
1 |
2 |
|
|
3 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
4 |
|
|
7 |
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
5 |
|
|
|
8 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||||
|
|
|
|
|
|
|
|
||||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
6 |
|
|
9 |
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
14 |
13 |
12 |
|
11 |
10 |
1 |
USB 2.0 Ports (USB01) |
|
** 8 |
Front Speaker (Lime) |
||
2 |
VGA/D-Sub Port |
|
|
9 |
Microphone (Pink) |
|
* 3 |
LAN RJ-45 Port |
|
|
10 |
USB 2.0 |
Ports (USB45) |
4 |
Central / Bass (Orange) |
|
11 |
USB 2.0 |
Ports (USB23) |
|
5 |
Rear Speaker (Black) |
|
12 |
VGA/HDMI Port |
||
6 |
Optical SPDIF Out Port |
|
13 |
VGA/DVI-D Port |
||
7 |
Line In (Light Blue) |
|
14 |
PS/2 Keyboard Port (Purple) |
*There are two LED next to the LAN port. Please refer to the table below for the LAN port LED indications.
LAN Port LED Indications
Activity/Link LED |
|
SPEED LED |
ACT/LINK |
SPEED |
||||||
|
LED |
LED |
||||||||
Status |
Description |
|
Status |
|
Description |
|||||
|
|
|
|
|
|
|||||
|
|
|
|
|||||||
Off |
No Link |
|
Off |
|
10Mbps connection |
|
|
|
|
|
|
|
|
|
|||||||
Blinking |
Data Activity |
|
Orange |
|
100Mbps connection |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
On |
Link |
|
Green |
|
1Gbps connection |
|
|
|
|
|
|
|
|
|
|
|
|
LAN Port |
|||
|
|
|
|
|
|
|
**If you use 2-channel speaker, please connect the speaker’s plug into “Front Speaker Jack”. See the table below for connection details in accordance with the type of speaker you use.
TABLE for Audio Output Connection
Audio Output Channels |
Front Speaker |
Rear Speaker |
Central / Bass |
Line In or |
|
(No. 8) |
(No. 5) |
(No. 4) |
Side Speaker |
|
|
|
|
(No. 7) |
|
|
|
|
|
2 |
V |
-- |
-- |
-- |
4 |
V |
V |
-- |
-- |
6 |
V |
V |
V |
-- |
|
|
|
|
|
8 |
V |
V |
V |
V |
To enable Multi-Streaming function, you need to connect a front panel audio cable to the front panel audio header. After restarting your computer, you will find “Mixer” tool on your system. Please select “Mixer ToolBox” , click “Enable playback multi-streaming”, and click
“ok”. Choose “2CH”, “4CH”, “6CH”, or “8CH” and then you are allowed to select “Realtek HDA Primary output” to use Rear Speaker, Central/Bass, and Front Speaker, or select “Realtek HDA Audio 2nd output” to use front panel audio.
3
English
ASRock H61DE/S3 Motherboard
1. Introduction
Thank you for purchasing ASRock H61DE/S3 motherboard, a reliable motherboard produced under ASRock’s consistently stringent quality control. It delivers excellent performance with robust design conforming to ASRock’s commitment to quality and endurance.
This Quick Installation Guide contains introduction of the motherboard and step-by- step installation guide. More detailed information of the motherboard can be found in the user manual presented in the Support CD.
Because the motherboard specifications and the BIOS software might be updated, the content of this manual will be subject to change without notice. In case any modifications of this manual occur, the updated version will be available on ASRock website without further notice. You may find the latest VGA cards and CPU support lists on ASRock website as well. ASRock website http://www.asrock.com
If you require technical support related to this motherboard, please visit our website for specific information about the model you are using. www.asrock.com/support/index.asp
1.1 Package Contents
ASRock H61DE/S3 Motherboard
(ATX Form Factor: 12.0-in x 8.6-in, 30.5 cm x 21.8 cm) ASRock H61DE/S3 Quick Installation Guide
ASRock H61DE/S3 Support CD
2 x Serial ATA (SATA) Data Cables (Optional)
1 x I/O Panel Shield
ASRock Reminds You...
To get better performance in Windows® 7 / 7 64-bit / VistaTM / VistaTM 64bit, it is recommended to set the BIOS option in Storage Configuration to AHCI mode. For the BIOS setup, please refer to the “User Manual” in our support CD for details.
English
4
ASRock H61DE/S3 Motherboard
1.2Specifications
Platform |
- ATX Form Factor: 12.0-in x 8.6-in, 30.5 cm x 21.8 cm |
|
- All Solid Capacitor design |
CPU |
- Supports 2nd Generation Intel® CoreTM i7 / i5 / i3 in |
|
LGA1155 Package |
|
- 4 + 1 Power Phase Design |
|
- Supports Intel® Turbo Boost 2.0 Technology |
|
- Supports K-Series unlocked CPU |
|
- Supports Hyper-Threading Technology (see CAUTION 1) |
Chipset |
- Intel® H61 |
Memory |
- Dual Channel DDR3 Memory Technology (see CAUTION 2) |
|
- 4 x DDR3 DIMM slots |
|
- Supports DDR3 1333/1066 non-ECC, un-buffered |
|
memory |
|
- Max. capacity of system memory: 16GB (see CAUTION 3) |
Expansion Slot |
- 1 x PCI Express 2.0 x16 slot (blue @ x16 mode) |
|
- 2 x PCI Express 2.0 x1 slots |
|
- 2 x PCI slots |
Graphics |
- Intel® HD Graphics 2000/3000 |
|
- Pixel Shader 4.1, DirectX 10.1 |
|
- Max. shared memory 1759MB (see CAUTION 4) |
|
- Three VGA Output options: D-Sub, DVI-D and HDMI |
|
(see CAUTION 5) |
|
- Supports HDMI 1.4a Technology with max. resolution up to |
|
1920x1200 @ 60Hz |
|
- Supports DVI with max. resolution up to 1920x1200 @ 60Hz |
|
- Supports D-Sub with max. resolution up to 2048x1536 @ |
|
75Hz |
|
- Supports Auto Lip Sync, Deep Color (12bpc), xvYCC and |
|
HBR (High Bit Rate Audio) with HDMI |
|
(Compliant HDMI monitor is required) (see CAUTION 6) |
|
- Supports Blu-ray Stereoscopic 3D with HDMI 1.4a |
|
- Supports HDCP function with DVI and HDMI ports |
|
- Supports Full HD 1080p Blu-ray (BD) / HD-DVD playback |
|
with DVI and HDMI ports |
Audio |
- 7.1 CH HD Audio (Realtek ALC887 Audio Codec) |
LAN |
- PCIE x1 Gigabit LAN 10/100/1000 Mb/s |
|
- Atheros® AR8151 |
|
- Supports Wake-On-LAN |
|
|
English
5
ASRock H61DE/S3 Motherboard
English
Rear Panel I/O |
I/O Panel |
|
- 1 x PS/2 Keyboard Port |
|
- 1 x VGA/D-Sub Port |
|
- 1 x VGA/DVI-D Port |
|
- 1 x HDMI Port |
|
- 1 x Optical SPDIF Out Port |
|
- 6 x Ready-to-Use USB 2.0 Ports |
|
- 1 x RJ-45 LAN Port with LED (ACT/LINK LED and SPEED |
|
LED) |
|
- HD Audio Jack: Rear Speaker/Central/Bass/Line in/Front |
|
Speaker/Microphone (see CAUTION 7) |
SATA3 |
- 2 x SATA3 6.0 Gb/s connectors by ASMedia ASM1061, |
|
support NCQ, AHCI and "Hot Plug" functions |
Connector |
- 4 x SATA2 3.0 Gb/s connectors, support NCQ, AHCI and |
|
Hot Plug functions |
|
- 2 x SATA3 6.0Gb/s connectors |
|
- 1 x IR header |
|
- 1 x COM port header |
|
- 1 x HDMI_SPDIF header |
|
- CPU/Chassis/Power FAN connector |
|
- 24 pin ATX power connector |
|
- 8 pin 12V power connector |
|
- Front panel audio connector |
|
- 2 x USB 2.0 headers (support 4 USB 2.0 ports) |
BIOS Feature |
- 32Mb AMI BIOS |
|
- AMI UEFI Legal BIOS with GUI support |
|
- Supports “Plug and Play” |
|
- ACPI 1.1 Compliance Wake Up Events |
|
- Supports jumperfree |
|
- SMBIOS 2.3.1 Support |
|
- IGPU, DRAM, PCH, CPU PLL, VTT, VCCSA Voltage |
|
Multi-adjustment |
Support CD |
- Drivers, Utilities, AntiVirus Software (Trial Version), ASRock |
|
Software Suite (CyberLink DVD Suite - OEM and Trial; |
|
Creative Sound Blaster X-Fi MB - Trial) |
Unique Feature |
- ASRock Extreme Tuning Utility (AXTU) (see CAUTION 8) |
|
- Instant Boot |
|
- ASRock Instant Flash (see CAUTION 9) |
|
- ASRock AIWI (see CAUTION 10) |
|
- ASRock APP Charger (see CAUTION 11) |
|
- SmartView (see CAUTION 12) |
|
- ASRock XFast USB (see CAUTION 13) |
6
ASRock H61DE/S3 Motherboard
|
- Hybrid Booster: |
|
- ASRock U-COP (see CAUTION 14) |
|
- Boot Failure Guard (B.F.G.) |
|
- Combo Cooler Option (C.C.O.) (see CAUTION 15) |
|
- Good Night LED |
Hardware |
- CPU Temperature Sensing |
Monitor |
- Chassis Temperature Sensing |
|
- CPU/Chassis/Power Fan Tachometer |
|
- CPU/Chassis Quiet Fan (Allow Chassis Fan Speed |
|
Auto-Adjust by CPU Temperature) |
|
- CPU/Chassis Fan Multi-Speed Control |
|
- Voltage Monitoring: +12V, +5V, +3.3V, CPU Vcore |
OS |
- Microsoft® Windows® 7 / 7 64-bit / VistaTM / VistaTM 64-bit |
|
/ XP / XP 64-bit compliant |
Certifications |
- FCC, CE, WHQL |
-ErP/EuP Ready (ErP/EuP ready power supply is required) (see CAUTION 16)
*For detailed product information, please visit our website: http://www.asrock.com
WARNING
Please realize that there is a certain risk involved with overclocking, including adjusting the setting in the BIOS, applying Untied Overclocking Technology, or using the third-party overclocking tools. Overclocking may affect your system stability, or even cause damage to the components and devices of your system.
It should be done at your own risk and expense. We are not responsible for possible damage caused by overclocking.
English
7
ASRock H61DE/S3 Motherboard
English
8
CAUTION!
1.About the setting of “Hyper Threading Technology”, please check page
42of “User Manual” in the support CD.
2.This motherboard supports Dual Channel Memory Technology. Before you implement Dual Channel Memory Technology, make sure to read the installation guide of memory modules on page 14 for proper installation.
3.Due to the operating system limitation, the actual memory size may be less than 4GB for the reservation for system usage under Windows® 7 / VistaTM / XP. For Windows® OS with 64-bit CPU, there is no such limitation.
4.The maximum shared memory size is defined by the chipset vendor and is subject to change. Please check Intel® website for the latest information.
5.You can choose to use two of the four monitors only. D-Sub, DVI-D and HDMI monitors cannot be enabled at the same time. Besides, with the DVI-to-HDMI adapter, the DVI-D port can support the same features as HDMIport.
6.xvYCC and Deep Color are only supported under Windows® 7 64-bit /
7.Deep Color mode will be enabled only if the display supports 12bpc in EDID. HBR is supported under Windows® 7 64-bit / 7 / VistaTM 64-bit / VistaTM.
7.For microphone input, this motherboard supports both stereo and mono modes. For audio output, this motherboard supports 2-channel, 4-chan- nel, 6-channel, and 8-channel modes. Please check the table on page 3 for proper connection.
8.ASRock Extreme Tuning Utility (AXTU) is an all-in-one tool to fine-tune different system functions in a user-friendly interface, which is including Hardware Monitor, Fan Control, Overclocking, OC DNA and IES. In Hardware Monitor, it shows the major readings of your system. In Fan Control, it shows the fan speed and temperature for you to adjust. In Overclocking, you are allowed to overclock CPU frequency for optimal system performance. In OC DNA, you can save your OC settings as a profile and share with your friends. Your friends then can load the OC profile to their own system to get the same OC settings. In IES (Intelligent Energy Saver), the voltage regulator can reduce the number of output phases to improve efficiency when the CPU cores are idle without sacrificing computing performance. Please visit our website for the operation procedures of ASRock Extreme Tuning Utility (AXTU). ASRock website: http://www.asrock.com
9.ASRock Instant Flash is a BIOS flash utility embedded in Flash ROM. This convenient BIOS update tool allows you to update system BIOS without entering operating systems first like MS-DOS or Windows®. With this utility, you can press <F6> key during the POST or press <F2> key to BIOS setup menu to access ASRock Instant Flash. Just launch this tool and save the new BIOS file to your USB flash drive, floppy disk or hard
ASRock H61DE/S3 Motherboard
drive, then you can update your BIOS only in a few clicks without preparing an additional floppy diskette or other complicated flash utility. Please be noted that the USB flash drive or hard drive must use FAT32/16/12 file system.
10.To experience intuitive motion controlled games is no longer only available at Wii. ASRock AIWI utility introduces a new way of PC gaming operation. ASRock AIWI is the world's first utility to turn your iPhone/iPod touch as a game joystick to control your PC games. All you have to do is just to install the ASRock AIWI utility either from ASRock official website or ASRock software support CD to your motherboard, and also download the free AIWI Lite from App store to your iPhone/iPod touch. Connecting your PC and apple devices via Bluetooth or WiFi networks, then you can start experiencing the exciting motion controlled games. Also, please do not forget to pay attention to ASRock official website regularly, we will continuously provide you the most up-do-date supported games! ASRock website: http://www.asrock.com/Feature/Aiwi/index.asp
11.If you desire a faster, less restricted way of charging your Apple devices, such as iPhone/iPod/iPad Touch, ASRock has prepared a wonderful solution for you - ASRock APP Charger. Simply installing the APP Charger driver, it makes your iPhone charged much quickly from your computer and up to 40% faster than before. ASRock APP Charger allows you to quickly charge many Apple devices simultaneously and even supports continuous charging when your PC enters into Standby mode (S1), Suspend to RAM (S3), hibernation mode (S4) or power off (S5). With APP Charger driver installed, you can easily enjoy the marvelous charging experience than ever.
ASRock website: http://www.asrock.com/Feature/AppCharger/index.asp
12.SmartView, a new function of internet browser, is the smart start page for IE that combines your most visited web sites, your history, your Facebook friends and your real-time newsfeed into an enhanced view for a more personal Internet experience. ASRock motherboards are exclusively equipped with the SmartView utility that helps you keep in touch with friends on-the-go. To use SmartView feature, please make sure your OS version is Windows® 7 / 7 64 bit / VistaTM / VistaTM 64 bit, and your browser version is IE8. ASRock website: http://www.asrock.com/Feature/ SmartView/index.asp
13.ASRock XFast USB can boost USB storage device performance. The performance may depend on the property of the device.
14.While CPU overheat is detected, the system will automatically shutdown. Before you resume the system, please check if the CPU fan on the motherboard functions properly and unplug the power cord, then plug it back again. To improve heat dissipation, remember to spray thermal grease between the CPU and the heatsink when you install the PC system.
English
9
ASRock H61DE/S3 Motherboard
15.Combo Cooler Option (C.C.O.) provides the flexible option to adopt three different CPU cooler types, Socket LGA 775, LGA 1155 and LGA 1156. Please be noticed that not all the 775 and 1156 CPU Fan can be used.
16.EuP, stands for Energy Using Product, was a provision regulated by European Union to define the power consumption for the completed system. According to EuP, the total AC power of the completed system shall be under 1.00W in off mode condition. To meet EuP standard, an EuP ready motherboard and an EuP ready power supply are required. According to Intel’s suggestion, the EuP ready power supply must meet the standard of 5v standby power efficiency is higher than 50% under 100 mA current consumption. For EuP ready power supply selection, we recommend you checking with the power supply manufacturer for more details.
English
10
ASRock H61DE/S3 Motherboard
2. Installation
Pre-installation Precautions
Take note of the following precautions before you install motherboard components or change any motherboard settings.
1.Unplug the power cord from the wall socket before touching any component. Failure to do so may cause severe damage to the motherboard, peripherals, and/or components.
2.To avoid damaging the motherboard components due to static electricity, NEVER place your motherboard directly on the carpet or the like. Also remember to use a grounded wrist strap or touch a safety grounded object before you handle components.
3.Hold components by the edges and do not touch the ICs.
4.Whenever you uninstall any component, place it on a grounded antstatic pad or in the bag that comes with the component.
5.When placing screws into the screw holes to secure the motherboard to the chassis, please do not over-tighten the screws! Doing so may damage the motherboard.
2.1CPU Installation
For the installation of Intel 1155-Pin CPU, |
|
|
|
|
|
|
|
|
|
|
|
|
please follow the steps below. |
|
|
Load Plate |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||||
|
|
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Load Lever |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Socket Body |
|
|
|
|
|
|
Contact Array |
|
|
|||||||
|
1155-Pin Socket Overview |
Before you insert the 1155-Pin CPU into the socket, please check if the CPU surface is unclean or if there is any bent pin on the socket. Do not force to insert the CPU into the socket if above situation is found. Otherwise, the CPU will be seriously damaged.
English
11
ASRock H61DE/S3 Motherboard
Step 1. Open the socket:
Step 1-1. Disengaging the lever by depressing down and out on the hook to clear retention tab.
Step 1-2. Rotate the load lever to fully open position at approximately 135 degrees.
Step 1-3. Rotate the load plate to fully open position at approximately 100 degrees.
Step 2. Remove PnP Cap (Pick and Place Cap).
English
1.It is recommended to use the cap tab to handle and avoid kicking off the PnP cap.
2.This cap must be placed if returning the motherboard for after service.
Step 3. Insert the 1155-Pin CPU: |
|
|
||||
Step 3-1. |
Hold the CPU by the edges where |
|
lineblack |
|||
|
|
|
are marked with black lines. |
|
||
|
|
|
|
|
||
Step 3-2. |
Orient the CPU with IHS (Integrated |
|
|
|||
|
|
|
Heat Sink) up. Locate Pin1 and the |
|
|
|
|
|
|
two orientation key notches. |
|
|
|
|
orientation key notch |
alignment key |
||||
Pin1 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Pin1
|
|
alignment key |
|
|
1155-Pin Socket |
orientation key notch |
||
1155-Pin CPU |
|
For proper inserting, please ensure to match the two orientation key notches of the CPU with the two alignment keys of the socket.
12
ASRock H61DE/S3 Motherboard
Step 3-3. Carefully place the CPU into the socket by using a purely vertical motion.
Step 3-4. Verify that the CPU is within the socket and properly mated to the orient keys.
Step 4. Close the socket:
Step 4-1. Rotate the load plate onto the IHS. Step 4-2. While pressing down lightly on load
plate, engage the load lever.
2.2Installation of CPU Fan and Heatsink
For proper installation, please kindly refer to the instruction manuals of your CPU fan and heatsink.
Below is an example to illustrate the installation of the heatsink for 1155-Pin CPU. Step 1. Apply thermal interface material onto center of
IHS on the socket surface.
Apply Thermal
Interface Material
Step 2. Place the heatsink onto the socket. Ensure fan cables are oriented on side closest to the CPU fan connector on the motherboard (CPU_ FAN1, see page 2, No. 2).
Step 3. Align fasteners with the motherboard throughholes.
Step 4. Rotate the fastener clockwise, then press down on fastener caps with thumb to install and lock. Repeat with remaining fasteners.
Fan cables on side closest to MB header
Fastener slots pointing straight out
Press Down
(4 Places)
If you press down the fasteners without rotating them clockwise, the heatsink cannot be secured on the motherboard.
Step 5. Connect fan header with the CPU fan connector on the motherboard. Step 6. Secure excess cable with tie-wrap to ensure cable does not interfere with
fan operation or contact other components.
Please be noticed that this motherboard supports Combo Cooler Option (C.C.O.), which provides the flexible option to adopt three different CPU cooler types, Socket LGA 775, LGA 1155 and LGA 1156. The white throughholes are for Socket LGA
1155/1156 CPU fan.
13
English
ASRock H61DE/S3 Motherboard
2.3 Installation of Memory Modules (DIMM)
This motherboard provides four 240-pin DDR3 (Double Data Rate 3) DIMM slots, and supports Dual Channel Memory Technology. For dual channel con g- uration, you always need to install identical (the same brand, speed, size and chip-type) DDR3 DIMM pair in the slots of the same color. In other words, you have to install identical DDR3 DIMM pair in Dual Channel A (DDR3_A1 and DDR3_B1; Blue slots; see p.2 No.5), so that Dual Channel Memory Technology can be activated. This motherboard also allows you to install four DDR3 DIMMs for dual channel con guration, and please install identical DDR3 DIMMs in all four slots. You may refer to the Dual Channel Memory Con guration Table below.
English
14
Dual Channel Memory Configurations
|
DDR3_A1 |
DDR3_A2 |
DDR3_B1 |
DDR3_B2 |
|
(Blue Slot) |
(White Slot) |
(Blue Slot) |
(White Slot) |
(1) |
Populated |
- |
Populated |
- |
(2)* |
Populated |
Populated |
Populated |
Populated |
*For the con guration (2), please install identical DDR3 DIMMs in all four slots.
1.If you want to install two memory modules, for optimal compatibility and reliability, it is recommended to install them in the blue slots (DDR3_A1 and DDR3_B1).
2.If only one memory module or three memory modules are installed in the DDR3 DIMM slots on this motherboard, it is unable to activate the Dual Channel Memory Technology.
3.If a pair of memory modules is NOT installed in the same Dual Channel, for example, installing a pair of memory modules in DDR3_A1 and DDR3_A2, it is unable to activate the Dual Channel Memory Technology .
4.It is not allowed to install a DDR or DDR2 memory module into DDR3 slot; otherwise, this motherboard and DIMM may be damaged.
5.Some DDR3 1GB double-sided DIMMs with 16 chips may not work on this motherboard. It is not recommended to install them on this motherboard.
6.If you install four single-sided DIMMs on this motherboard, they will run at DDR3 1066 only.
7.It is not recommended to install the double-sided DIMM on DDR3_ A2 slot.
ASRock H61DE/S3 Motherboard
Installing a DIMM
Please make sure to disconnect power supply before adding or removing DIMMs or the system components.
Step 1. Unlock a DIMM slot by pressing the retaining clips outward.
Step 2. Align a DIMM on the slot such that the notch on the DIMM matches the break on the slot.
notch break
notch
break
The DIMM only fits in one correct orientation. It will cause permanent damage to the motherboard and the DIMM if you force the DIMM into the slot at incorrect orientation.
Step 3. Firmly insert the DIMM into the slot until the retaining clips at both ends fully snap back in place and the DIMM is properly seated.
English
15
ASRock H61DE/S3 Motherboard
2.4 Expansion Slots (PCI and PCI Express Slots)
There are 2 PCI slot and 3 PCI Express slots on this motherboard.
PCI slots: PCI slots are used to install expansion cards that have the 32-bit PCI interface.
PCIE slots:
PCIE1 (PCIE x16 slot; Blue) is used for PCI Express x16 lane width graphics cards.
PCIE2 / PCIE3 (PCIE x1 slot; White) is used for PCI Express cards with x1 lane width cards, such as Gigabit LAN card, SATA2 card, etc.
Installing an expansion card
Step 1. Before installing the expansion card, please make sure that the power supply is switched off or the power cord is unplugged. Please read the documentation of the expansion card and make necessary hardware settings for the card before you start the installation.
Step 2. Remove the system unit cover (if your motherboard is already installed in a chassis).
Step 3. Remove the bracket facing the slot that you intend to use. Keep the screws for later use.
Step 4. Align the card connector with the slot and press firmly until the card is completely seated on the slot.
Step 5. Fasten the card to the chassis with screws. Step 6. Replace the system cover.
English
16
ASRock H61DE/S3 Motherboard
2.5 Dual Monitor and Surround Display Features
Dual Monitor Feature
This motherboard supports dual monitor feature. With the internal VGA output support (DVI-D, D-Sub and HDMI), you can easily enjoy the benefits of dual monitor feature without installing any add-on VGA card to this motherboard. This motherboard also provides independent display controllers for DVI-D, D-Sub and HDMI to support dual VGA output so that DVI-D, D-sub and HDMI can drive same or different display contents.
To enable dual monitor feature, please follow the below steps:
1.Connect DVI-D monitor cable to VGA/DVI-D port on the I/O panel, connect D-Sub monitor cable to VGA/D-Sub port on the I/O panel, or connect HDMI monitor cable to HDMI port on the I/O panel.
VGA/D-Sub port
VGA/DVI-D port HDMI port
2.If you have installed onboard VGA driver from our support CD to your system already, you can freely enjoy the benefits of dual monitor function after your system boots. If you haven’t installed onboard VGA driver yet, please install onboard VGA driver from our support CD to your system and restart your computer.
D-Sub, DVI-D and HDMI monitors cannot be enabled at the same time. You can only choose the combination: DVI-D + HDMI, DVI-D + D-Sub, or HDMI + D-Sub.
English
17
ASRock H61DE/S3 Motherboard
English
18
Surround Display Feature
This motherboard supports surround display upgrade. With the internal VGA output support (DVI-D, D-Sub and HDMI) and external add-on PCI Express VGA cards, you can easily enjoy the benefits of surround display feature.
Please refer to the following steps to set up a surround display environment:
1.Install the PCI Express VGA card on PCIE1 slot. Please refer to page 16 for proper expansion card installation procedures for details.
2.Connect DVI-D monitor cable to VGA/DVI-D port on the I/O panel, connect D-Sub monitor cable to VGA/D-Sub port on the I/O panel, or connect HDMI monitor cable to HDMI port on the I/O panel. Then connect other monitor cables to the corresponding connectors of the add-on PCI Express VGA card on PCIE1 slot.
3.Boot your system. Press <F2> or <Del> to enter UEFI setup. Enter “Onboard VGA Share Memory” option to adjust the memory capability to [32MB], [64MB], [128MB], [256MB] or [512MB] to enable the function of VGA/D-sub. Please make sure that the value you select is less than the total capability of the system memory. If you do not adjust the UEFI setup, the default value of “Onboard VGA Share Memory”, [Auto], will disable VGA/D-Sub function when the add-on VGA card is inserted to this motherboard.
4.Install the onboard VGA driver and the add-on PCI Express VGA card driver to your system. If you have installed the drivers already, there is no need to install them again.
5.Set up a multi-monitor display.
For Windows® XP / XP 64-bit OS:
Right click the desktop, choose “Properties”, and select the “Settings” tab so that you can adjust the parameters of the multi-monitor according to the steps below.
A.Click the “Identify” button to display a large number on each monitor.
B.Right-click the display icon in the Display Properties dialog that you wish to be your primary monitor, and then select “Primary”. When you use multiple monitors with your card, one monitor will always be Primary, and all additional monitors will be designated as Secondary.
C.Select the display icon identified by the number 2.
D.Click “Extend my Windows desktop onto this monitor”.
E.Right-click the display icon and select “Attached”, if necessary.
F.Set the “Screen Resolution” and “Color Quality” as appropriate for the second monitor. Click “Apply” or “OK” to apply these new values.
G.Repeat steps C through E for the diaplay icon identified by the number one, two, three and four.
ASRock H61DE/S3 Motherboard
For Windows® 7 / 7 64-bit / VistaTM / VistaTM 64-bit OS:
Right click the desktop, choose “Personalize”, and select the “Display Settings” tab so that you can adjust the parameters of the multi-monitor according to the steps below.
A.Click the number ”2” icon.
B.Click the items “This is my main monitor” and “Extend the desktop onto this monitor”.
C.Click “OK” to save your change.
D.Repeat steps A through C for the display icon identified by the number three and four.
6.Use Surround Display. Click and drag the display icons to positions representing the physical setup of your monitors that you would like to use. The placement of display icons determines how you move items from one monitor to another.
HDCP Function
HDCP function is supported on this motherboard. To use HDCP function with this motherboard, you need to adopt the monitor that supports HDCP function as well. Therefore, you can enjoy the superior display quality with high-definition HDCP encryption contents. Please refer to below instruction for more details about HDCP function.
What is HDCP?
HDCP stands for High-Bandwidth Digital Content Protection, a specification developed by Intel® for protecting digital entertainment content that uses the DVI interface. HDCP is a copy protection scheme to eliminate the possibility of intercepting digital data midstream between the video source,
or transmitter - such as a computer, DVD player or set-top box - and the digital display, or receiver - such as a monitor, television or projector. In other words, HDCP specification is designed to protect the integrity of content as it is being transmitted.
Products compatible with the HDCP scheme such as DVD players, satellite and cable HDTV set-top-boxes, as well as few entertainment PCs requires a secure connection to a compliant display. Due to the increase in manufacturers employing HDCP in their equipment, it is highly recommended that the HDTV or LCD monitor you purchase is compatible.
19
English
ASRock H61DE/S3 Motherboard
2.6 Jumpers Setup
The illustration shows how jumpers are setup. When the jumper cap is placed on pins, the jumper is “Short”. If no jumper cap is placed on pins, the jumper is “Open”. The illustration shows a 3-pin jumper whose pin1 and pin2 are “Short” when jumper cap is placed on these 2 pins.
Jumper |
Setting |
Description |
Clear CMOS Jumper |
|
|
(CLRCMOS1) |
|
|
(see p.2, No. 10) |
Default |
Clear CMOS |
|
Note: CLRCMOS1 allows you to clear the data in CMOS. To clear and reset the system parameters to default setup, please turn off the computer and unplug the power cord from the power supply. After waiting for 15 seconds, use a jumper cap to short pin2 and pin3 on CLRCMOS1 for 5 seconds. However, please do not clear the CMOS right after you update the BIOS. If you need to clear the CMOS when you just finish updating the BIOS, you must boot up the system first, and then shut it down before you do the clear-CMOS action. Please be noted that the password, date, time, user default profile, 1394 GUID and MAC address will be cleared only if the CMOS battery is removed.
English
20
ASRock H61DE/S3 Motherboard
2.7 Onboard Headers and Connectors
Onboard headers and connectors are NOT jumpers. Do NOT place jumper caps over these headers and connectors. Placing jumper caps over the headers and connectors will cause permanent damage of the motherboard!
Serial ATAII Connectors
(SATA2_0: see p.2, No. 12) (SATA2_1: see p.2, No. 19) (SATA2_2: see p.2, No. 13) (SATA2_3: see p.2, No. 17)
SATA2_0 SATA2_2
SATA2_1 SATA2_3
These four Serial ATAII (SATAII) connectors support SATA data cables for internal storage devices. The current SATAII interface allows up to 3.0 Gb/s data transfer rate.
Serial ATA3 Connectors
(SATA3_1: see |
p.2, No. 14) |
SATA3_1 |
(SATA3_2: see |
p.2, No. 15) |
SATA3_2 |
These two Serial ATA3 (SATA3) connectors support SATA data cables for internal storage devices. The current SATA3 interface allows up to 6.0 Gb/s data transfer rate.
Serial ATA (SATA) |
|
|
|
|
|
|
|
|
|
|
|
|
Either end of the SATA data |
Data Cable |
|
|
|
|
|
|
|
|
|
|
|
|
cable can be connected to the |
(Optional) |
|
|
|
|
|
|
|
|
|
|
|
|
SATA / SATAII / SATA3 hard |
|
|
|
|
|
|
|
|
|
|
|
|
|
disk or the SATAII / SATA3 |
|
|
|
|
|
|
|
|
|
|
|
|
|
connector on this motherboard. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
USB 2.0 Headers |
|
|
|
|
|
|
|
|
|
|
|
|
Besides six default USB 2.0 |
(9-pin USB6_7) |
|
|
|
|
|
|
|
|
|
|
|
|
ports on the I/O panel, there |
(see p.2 No. 22) |
|
|
|
|
|
|
|
|
|
|
|
|
are two USB 2.0 headers on |
|
|
|
|
|
|
|
|
|
|
|
|
|
this motherboard. Each |
|
|
|
|
|
|
|
|
|
|
|
|
|
USB 2.0 header can support |
|
|
|
|
|
|
|
|
|
|
|
|
|
two USB 2.0 ports. |
(9-pin USB8_9) |
|
|
USB_PWR |
|
|||||||||
|
|
|
|
|
P-9 |
|
|||||||
(see p.2 No. 21) |
|
|
|
|
|
|
|
P+9 |
|
||||
|
|
|
|
|
|
|
|
||||||
|
|
|
|
|
|
|
|
GND |
|
||||
|
1 |
|
|
|
|
|
|
|
|
DUMMY |
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
GND |
|
|||
|
|
|
|
|
|
|
|
P+8 |
|
||||
|
|
|
|
|
P-8 |
|
|||||||
|
|
|
USB_PWR |
|
|||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Infrared Module Header |
|
|
|
|
|
|
IRTX |
This header supports an |
|||||
|
|
|
|
|
|
|
|
+5VSB |
optional wireless transmitting |
||||
(5-pin IR1) |
|
|
|
|
|
|
|
|
DUMMY |
||||
(see p.2 No. 23) |
1 |
|
|
|
|
|
|
and receiving infrared module. |
|||||
|
|
|
|
|
|
||||||||
|
|
|
|
|
|
||||||||
|
|
|
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
GND |
|
|||
|
|
|
|
|
|
|
|
IRRX |
|
21
English
ASRock H61DE/S3 Motherboard
Front Panel Audio Header |
|
|
GND |
|||||||||
(9-pin HD_AUDIO1) |
|
|
|
|
PRESENCE# |
|||||||
|
|
|
|
|
|
MIC_RET |
||||||
|
|
|
|
|
|
|
|
|
|
|
OUT_RET |
|
(see p.2 No. 28) |
1 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
OUT2_L |
|
|
|
|
|
|
|
|
|
J_SENSE |
||||
|
|
|
|
|
|
|
OUT2_R |
|||||
|
|
|
|
|
MIC2_R |
|||||||
|
|
|
MIC2_L |
This is an interface for front panel audio cable that allows convenient connection and control of audio devices.
1.High Definition Audio supports Jack Sensing, but the panel wire on the chassis must support HDA to function correctly. Please follow the instruction in our manual and chassis manual to install your system.
2.If you use AC’97 audio panel, please install it to the front panel audio header as below:
A.Connect Mic_IN (MIC) to MIC2_L.
B.Connect Audio_R (RIN) to OUT2_R and Audio_L (LIN) to OUT2_L.
C.Connect Ground (GND) to Ground (GND).
D.MIC_RET and OUT_RET are for HD audio panel only. You don’t need to connect them for AC’97 audio panel.
E.To activate the front mic.
For Windows® XP / XP 64-bit OS:
Select “Mixer”. Select “Recorder”. Then click “FrontMic”. For Windows® 7 / 7 64-bit / VistaTM / VistaTM 64-bit OS:
Go to the "FrontMic" Tab in the Realtek Control panel. Adjust “Recording Volume”.
System Panel Header |
This header accommodates |
(9-pin PANEL1) |
several system front panel |
(see p.2 No. 16) |
functions. |
English
22
Connect the power switch, reset switch and system status indicator on the chassis to this header according to the pin assignments below. Note the positive and negative pins before connecting the cables.
PWRBTN (Power Switch):
Connect to the power switch on the chassis front panel. You may configure the way to turn off your system using the power switch.
RESET (Reset Switch):
Connect to the reset switch on the chassis front panel. Press the reset switch to restart the computer if the computer freezes and fails to perform a normal restart.
PLED (System Power LED):
Connect to the power status indicator on the chassis front panel. The LED is on when the system is operating. The LED keeps blinking when the system is in S1 sleep state. The LED is off when the system is in S3/S4 sleep state or powered off (S5).
ASRock H61DE/S3 Motherboard
HDLED (Hard Drive Activity LED):
Connect to the hard drive activity LED on the chassis front panel. The LED is on when the hard drive is reading or writing data.
The front panel design may differ by chassis. A front panel module mainly consists of power switch, reset switch, power LED, hard drive activity LED, speaker and etc. When connecting your chassis front panel module to this header, make sure the wire assignments and the pin assign-ments are matched correctly.
Chassis Speaker Header |
Please connect the chassis |
(4-pin SPEAKER 1) |
speaker to this header. |
(see p.2 No. 18) |
|
Chassis and Power Fan Connectors
(4-pin CHA_FAN1)
(see p.2 |
No. 20) |
FAN_SPEED_CONTROL +12V |
|
|
|
GND |
|
|
|
CHA_FAN_SPEED |
|
(3-pin CHA_FAN2) |
GND |
||
(see p.2 |
No. 8) |
+12V |
|
CHA_FAN_SPEED |
|||
(3-pin CHA_FAN3) |
|
||
(see p.2 |
No. 31) |
|
|
(3-pin PWR_FAN1) |
PWR_FAN_SPEED |
||
+12V |
|||
(see p.2 |
No. 32) |
||
GND |
Please connect the fan cables to the fan connectors and match the black wire to the ground pin.
CPU Fan Connectors |
FAN_SPEED_CONTROL |
Please connect the CPU fan |
|
|
|
(4-pin CPU_FAN1) |
CPU_FAN_SPEED |
cable to the connector and |
+12V |
||
(see p.2 No. 2) |
GND |
match the black wire to the |
|
||
|
1 2 3 4 |
ground pin. |
Though this motherboard provides 4-Pin CPU fan (Quiet Fan) support, the 3-Pin CPU fan still can work successfully even without the fan speed control function. If you plan to connect the 3-Pin CPU fan to the CPU fan connector on this motherboard, please connect it to Pin 1-3.
Pin 1-3 Connected
3-Pin Fan Installation
(3-pin CPU_FAN2) |
GND |
|
|
+12V |
|
(see p.2 No. 3) |
CPU_FAN_SPEED |
|
|
|
|
|
|
|
|
|
|
23
English
ASRock H61DE/S3 Motherboard
English
ATX Power Connector |
12 |
24 |
Please connect an ATX power |
|||||
(24-pin ATXPWR1) |
|
|
supply to this connector. |
|
||||
(see p.2 No. 7) |
|
|
|
|
|
|
|
|
|
|
1 |
13 |
|
|
|
|
|
|
|
|
|
|
|
|||
|
Though this motherboard provides 24-pin ATX power connector, |
12 |
|
|
24 |
|||
|
|
|
||||||
|
it can still work if you adopt a traditional 20-pin ATX power supply. |
|
|
|
|
|||
|
To use the 20-pin ATX power supply, please plug your |
|
|
|
|
|||
|
power supply along with Pin 1 and Pin 13. |
|
|
|
|
|
||
|
|
|
20-Pin ATX Power Supply Installation |
1 |
|
|
13 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||
ATX 12V Power Connector |
8 |
5 |
Please connect an ATX 12V |
|
||||
(8-pin ATX12V1) |
|
|
power supply to this connector. |
|||||
(see p.2 No. 4) |
4 |
1 |
|
|
|
|
|
Though this motherboard provides 8-pin ATX 12V power connector, it can still work if you adopt a traditional 4-pin ATX 12V power supply. To use the 4-pin ATX power supply, please plug your power supply along with Pin 1 and Pin 5.
|
8 |
5 |
|
|
|
|
|
|
4-Pin ATX 12V Power Supply Installation 4 |
1 |
|
|
|
|
|
Serial port Header |
This COM1 header supports a |
||
(9-pin COM1) |
serial port module. |
|
|
(see p.2 No. 24) |
|
|
|
HDMI_SPDIF Header
(2-pin HDMI_SPDIF1)
(see p.2 No. 29)
1 |
GND
SPDIFOUT
HDMI_SPDIF header, providing SPDIF audio output to HDMI VGA card, allows the system to connect HDMI Digital TV/ projector/LCD devices. Please connect the HDMI_SPDIF connector of HDMI VGA card to this header.
24
ASRock H61DE/S3 Motherboard
2.8Driver Installation Guide
To install the drivers to your system, please insert the support CD to your optical drive first. Then, the drivers compatible to your system can be auto-detected and listed on the support CD driver page. Please follow the order from up to bottom side to install those required drivers. Therefore, the drivers you install can work properly.
2.9 Installing Windows® 7 / 7 64-bit / VistaTM / VistaTM 64-bit / XP / XP 64-bit Without RAID Functions
If you want to install Windows® 7 / 7 64-bit / VistaTM / VistaTM 64-bit / XP / XP 64bit OS on your SATA / SATAII / SATA3 HDDs without RAID functions, please follow below procedures according to the OS you install.
2.9.1Installing Windows® XP / XP 64-bit Without RAID
Functions
If you want to install Windows® XP / XP 64-bit OS on your SATA / SATAII / SATA3 HDDs without RAID functions, please follow below steps.
AHCI mode is not supported under Windows® XP / XP 64-bit OS.
Using SATA / SATAII / SATA3 HDDs without NCQ function
STEP 1: Set up UEFI.
A.Enter UEFI SETUP UTILITY Advanced screen SATA Configuration.
B.Set the option “SATA Mode” to [IDE] for SATA2 ports. Set the option “SATA3 Mode” to [IDE] for SATA3 ports.
STEP 2: Install Windows® XP / XP 64-bit OS on your system.
English
25
ASRock H61DE/S3 Motherboard
2.9.2Installing Windows® 7 / 7 64-bit / VistaTM / VistaTM 64-bit
Without RAID Functions
If you want to install Windows® 7 / 7 64-bit / VistaTM / VistaTM 64-bit OS on your SATA / SATAII / SATA3 HDDs without RAID functions, please follow below steps.
Using SATA / SATAII / SATA3 HDDs with NCQ function
STEP 1: Set Up UEFI.
A.Enter UEFI SETUP UTILITY Advanced screen SATA Configuration.
B.Set the option “SATA Mode” to [AHCI] for SATA2 ports. Set the option “SATA3 Mode” to [AHCI] for SATA3 ports.
STEP 2: Install Windows® 7 / 7 64-bit / VistaTM / VistaTM 64-bit OS on your system.
Using SATA / SATAII / STA3 HDDs without NCQ function
STEP 1: Set up UEFI.
A.Enter UEFI SETUP UTILITY Advanced screen SATA Configuration.
B.Set the option “SATA Mode” to [IDE] for SATA2 ports. Set the option “SATA3 Mode” to [IDE] for SATA3 ports.
STEP 2: Install Windows® 7 / 7 64-bit / VistaTM / VistaTM 64-bit OS on your system.
English
26
ASRock H61DE/S3 Motherboard
3. BIOS Information
The Flash Memory on the motherboard stores BIOS Setup Utility. When you start up the computer, please press <F2> or <Del> during the Power-On-Self-Test (POST) to enter BIOS Setup utility; otherwise, POST continues with its test routines. If you wish to enter BIOS Setup after POST, please restart the system by pressing <Ctl> + <Alt> + <Delete>, or pressing the reset button on the system chassis. The BIOS Setup program is designed to be user-friendly. It is a menu-driven program, which allows you to scroll through its various sub-menus and to select among the predetermined choices. For the detailed information about BIOS Setup, please refer to the User Manual (PDF file) contained in the Support CD.
4. Software Support CD information
This motherboard supports various Microsoft® Windows® operating systems: 7 / 7 64-bit / VistaTM / VistaTM 64-bit / XP / XP 64-bit. The Support CD that came with the motherboard contains necessary drivers and useful utilities that will enhance motherboard features. To begin using the Support CD, insert the CD into your CD-ROM drive. It will display the Main Menu automatically if “AUTORUN” is enabled in your computer. If the Main Menu does not appear automatically, locate and double-click on the file “ASSETUP.EXE” from the BIN folder in the Support CD to display the menus.
English
27
ASRock H61DE/S3 Motherboard
1. Einführung
Wir danken Ihnen für den Kauf des ASRock H61DE/S3 Motherboard, ein zuverlässiges Produkt, welches unter den ständigen, strengen Qualitätskontrollen von ASRock gefertigt wurde. Es bietet Ihnen exzellente Leistung und robustes Design, gemäß der Verpflichtung von ASRock zu Qualität und Halbarkeit. Diese Schnellinstallationsanleitung führt in das Motherboard und die schrittweise Installation ein. Details über das Motherboard finden Sie in der Bedienungsanleitung auf der Support-CD.
Da sich Motherboard-Spezifikationen und BIOS-Software verändern können, kann der Inhalt dieses Handbuches ebenfalls jederzeit geändert werden. Für den Fall, dass sich Änderungen an diesem Handbuch ergeben, wird eine neue Version auf der ASRock-Website, ohne weitere Ankündigung, verfügbar sein. Die neuesten Grafikkarten und unterstützten CPUs sind auch auf der ASRock-Website aufgelistet.
ASRock-Website: http://www.asrock.com
Wenn Sie technische Unterstützung zu Ihrem Motherboard oder spezifische Informationen zu Ihrem Modell benötigen, besuchen Sie bitte unsere Webseite:
www.asrock.com/support/index.asp
1.1 Kartoninhalt
ASRock H61DE/S3 Motherboard
(ATX-Formfaktor: 30.5 cm x 21.8 cm; 12.0 Zoll x 8.6 Zoll)
ASRock H61DE/S3 Schnellinstallationsanleitung
ASRock H61DE/S3 Support-CD
Zwei Serial ATA (SATA) -Datenkabel (optional)
Ein I/O Shield
ASRock erinnert...
Zur besseren Leistung unter Windows® 7 / 7, 64 Bit / VistaTM / VistaTM 64 Bit empfehlen wir, die Speicherkonfiguration im BIOS auf den AHCIModus einzustellen. Hinweise zu den BIOS-Einstellungen finden Sie in der Bedienungsanleitung auf der mitgelieferten CD.
Deutsch
28
ASRock H61DE/S3 Motherboard
1.2Spezifikationen
Plattform |
- ATX-Formfaktor: 30.5 cm x 21.8 cm; 12.0 Zoll x 8.6 Zoll |
|
- Alle Feste Kondensatordesign |
CPU |
- Unterstützt Intel® CoreTM (2te Generation) i7 / i5 / i3 im |
|
LGA1155-Paket |
|
- 4 + 1-Stromphasendesign |
|
- Unterstützt Intel® Turbo Boost 2.0-Technologie |
|
- Unterstützt freigegebene CPU der K-Serie |
|
- Unterstützt Hyper-Threading-Technologie |
|
(siehe VORSICHT 1) |
Chipsatz |
- Intel® H61 |
Speicher |
- Unterstützung von Dual-Kanal-Speichertechnologie |
|
(siehe VORSICHT 2) |
|
- 4 x Steckplätze für DDR3 |
|
- Unterstützt DDR3 1333/1066 non-ECC, ungepufferter |
|
Speicher |
|
- Max. Kapazität des Systemspeichers: 16GB |
|
(siehe VORSICHT 3) |
Erweiterungs- |
- 1 x PCI Express 2.0 x16-Steckplatz (blau für x16-Modus) |
steckplätze |
- 2 x PCI Express 2.0 x1-Steckplätze |
|
- 2 x PCI -Steckplätze |
Onboard-VGA |
- Intel® HD Gra k 2000/3000 |
|
- Pixel Shader 4.1, DirectX 10.1 |
|
- Maximal gemeinsam genutzter Speicher 1759MB |
|
(siehe VORSICHT 4) |
|
- Drei VGA-Ausgangsoptionen: D-Sub, DVI-D sowie HDMI |
|
(siehe VORSICHT 5) |
|
- Unterstützt HDMI 1.4a mit einer maximalen Au ösung von |
|
1920 x 1200 bei 60 Hz |
|
- Unterstützt DVI mit einer maximalen Au ösung von |
|
1920 x 1200 bei 60 Hz |
|
- Unterstützt D-Sub mit einer maximalen Au ösung von |
|
2048 x 1536 bei 75 Hz |
|
- Unterstützt Auto Lip Sync, Deep Color (12bpc), xvYCC und |
|
HBR (High Bit Rate-Audio) mit HDMI (kompatibler HDMI- |
|
Bildschirm erforderlich) (siehe VORSICHT 6) |
|
- Unterstützt stereoskopisches 3D per Blu-ray mit HDMI 1.4a |
|
- Unterstützt HDCP-Funktion mit DVIund HDMI-Ports |
|
- Unterstutzt 1080p Blu-ray (BD) / HD-DVD-Wiedergabe mit |
|
DVIund HDMI-Ports |
Deutsch
29
ASRock H61DE/S3 Motherboard
Deutsch
30
Audio |
- 7.1 CH HD Audio (Realtek ALC887 Audio Codec) |
LAN |
- PCIE x1 Gigabit LAN 10/100/1000 Mb/s |
|
- Atheros® AR8151 |
|
- Unterstützt Wake-On-LAN |
E/A-Anschlüsse |
I/O Panel |
an der |
- 1 x PS/2-Tastaturanschluss |
Rückseite |
- 1 x VGA/D-Sub port |
|
- 1 x VGA/DVI-D port |
|
- 1 x HDMI port |
|
- 1 x optischer SPDIF-Ausgang |
|
- 6 x Standard-USB 2.0-Anschlüsse |
|
- 1 x RJ-45 LAN Port mit LED (ACT/LINK LED und SPEED |
|
LED) |
|
- HD Audiobuchse: Lautsprecher hinten / Mitte/Bass / |
|
Audioeingang / Lautsprecher vorne / Mikrofon |
|
(siehe VORSICHT 7) |
SATA3 |
- 2 x ASMedia ASM1061 SATA 3-Anschlüsse (6,0 Gb/s); |
|
unterstützt NCQ-, AHCI-und „Hot Plug“ (Hot-Plugging)- |
|
Funktionen |
|
|
Anschlüsse |
- 4 x SATA2 3,0 GB/s-Anschlüsse, unterstützen NCQ-, AHCI- |
|
und „Hot Plug“ (Hot-Plugging)- Funktionen |
|
- 2 x SATA3 6,0 GB/s-Anschlüsse |
|
- 1 x Infrarot-Modul-Header |
|
- 1 x COM-Anschluss-Header |
|
- CPU/Gehäuse/Stromlüfter-Anschluss |
|
- 24-pin ATX-Netz-Header |
|
- 8-pin anschluss für 12V-ATX-Netzteil |
|
- Anschluss für Audio auf der Gehäusevorderseite |
|
- 2 x USB 2.0-Anschlüsse (Unterstützung 4 zusätzlicher |
|
USB 2.0-Anschlüsse) |
BIOS |
- 32Mb AMI BIOS |
|
- AMIs Legal BIOS UEFI mit GUI-Unterstützung |
|
- Unterstützung für “Plug and Play” |
|
- ACPI 1.1-Weckfunktionen |
|
- JumperFree-Übertaktungstechnologie |
|
- SMBIOS 2.3.1 |
|
- IGPU, DRAM, PCH, CPU PLL, VTT, VCCSA |
|
Stromspannung Multianpassung |
|
|
ASRock H61DE/S3 Motherboard