ASRock G31M-S, G31M-GS Installation 05-2009

0 (0)

Copyright Notice:

No part of this installation guide may be reproduced, transcribed, transmitted, or translated in any language, in any form or by any means, except duplication of documentation by the purchaser for backup purpose, without written consent of ASRock Inc.

Products and corporate names appearing in this guide may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners’ benefit, without intent to infringe.

Disclaimer:

Specifications and information contained in this guide are furnished for informational use only and subject to change without notice, and should not be constructed as a commitment by ASRock. ASRock assumes no responsibility for any errors or omissions that may appear in this guide.

With respect to the contents of this guide, ASRock does not provide warranty of any kind, either expressed or implied, including but not limited to the implied warranties or conditions of merchantability or fitness for a particular purpose. In no event shall ASRock, its directors, officers, employees, or agents be liable for any indirect, special, incidental, or consequential damages (including damages for loss of profits, loss of business, loss of data, interruption of business and the like), even if ASRock has been advised of the possibility of such damages arising from any defect or error in the guide or product.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1)this device may not cause harmful interference, and

(2)this device must accept any interference received, including interference that may cause undesired operation.

CALIFORNIA, USA ONLY

The Lithium battery adopted on this motherboard contains Perchlorate, a toxic substance controlled in Perchlorate Best Management Practices (BMP) regulations passed by the California Legislature. When you discard the Lithium battery in California, USA, please follow the related regulations in advance.

“Perchlorate Material-special handling may apply, see www.dtsc.ca.gov/hazardouswaste/perchlorate

ASRock Website: http://www.asrock.com

Published May 2009

Copyright©2009 ASRock INC. All rights reserved.

1

English

ASRock G31M-GS / G31M-S Motherboard

ASRock G31M-S, G31M-GS Installation 05-2009

Motherboard Layout

English

2

1

PS2_USB_PWR1 Jumper

15

USB 2.0 Header (USB6_7, Blue)

2

775-Pin CPU Socket

16

USB 2.0 Header (USB4_5, Blue)

3

North Bridge Controller

17

System Panel Header (PANEL1, Orange)

4

CPU Fan Connector (CPU_FAN1)

18

BIOS SPI Chip

5

2 x 240-pin DDR2 DIMM Slots

19

Chassis Fan Connector (CHA_FAN1)

 

(Dual Channel: DDRII_1, DDRII_2; Yellow)

20

Floppy Connector (FLOPPY1)

6

ATX Power Connector (ATXPWR1)

21

Front Panel Audio Header

7

IDE1 Connector (IDE1, Blue)

 

(HD_AUDIO1, Lime)

8

Clear CMOS Jumper (CLRCMOS1)

22

PCI Slots (PCI1- 2)

9

South Bridge Controller

23

Internal Audio Connector: CD1 (Black)

10

Third SATAII Connector (SATAII_3; Orange)

24

PCI Express x16 Slot (PCIE2)

11

Fourth SATAII Connector (SATAII_4; Orange)

25

PCI Express x1 Slot (PCIE1)

12

Secondary SATAII Connector (SATAII_2; Red) 26

Print Port Header (LPT1, Purple)

13

Primary SATAII Connector (SATAII_1; Red)

27

OC 800 / FSB0 / FSB1 Jumper

14

Chassis Speaker Header (SPEAKER 1,

28

ATX 12V Connector (ATX12V1)

 

Purple)

 

 

ASRock G31M-GS / G31M-S Motherboard

I/O Panel

1

PS/2 Mouse Port (Green)

6

Microphone (Pink)

2

USB 2.0 Ports (USB23)

7

USB 2.0 Ports (USB01)

3

RJ-45 Port

8

VGA Port

4

Line

In (Light Blue)

9

COM Port

5

Line

Out (Lime)

10

PS/2 Keyboard Port (Purple)

*To enable Multi-Streaming function, you need to connect a front panel audio cable to the front panel audio header. Please refer to below steps for the software setting of Multi-Streaming.

For Windows® XP:

After restarting your computer, you will find “Mixer” tool on your system. Please select “Mixer ToolBox” , click “Enable playback multi-streaming”, and click “ok”. Choose “2CH” or

“4CH” and then you are allowed to select “Realtek HDA Primary output” to use Rear Speaker and Front Speaker, or select “Realtek HDA Audio 2nd output” to use front panel audio. Then reboot your system.

For Windows® VistaTM:

After restarting your computer, please double-click “Realtek HD Audio Manager” on the system tray. Set “Speaker Configuration” to “Quadraphonic” or “Stereo”. Click “Device advanced settings”, choose “Make front and rear output devices playbacks two different audio streams simultaneously”, and click “ok”. Then reboot your system.

English

3

ASRock G31M-GS / G31M-S Motherboard

1. Introduction

Thank you for purchasing ASRock G31M-GS / G31M-S motherboard, a reliable motherboard produced under ASRock’s consistently stringent quality control. It delivers excellent performance with robust design conforming to ASRock’s commitment to quality and endurance.

This Quick Installation Guide contains introduction of the motherboard and step-by- step installation guide. More detailed information of the motherboard can be found in the user manual presented in the Support CD.

Because the motherboard specifications and the BIOS software might be updated, the content of this manual will be subject to change without notice. In case any modifications of this manual occur, the updated version will be available on ASRock website without further notice. You may find the latest VGA cards and CPU support lists on ASRock website as well. ASRock website http://www.asrock.com

If you require technical support related to this motherboard, please visit our website for specific information about the model you are using. www.asrock.com/support/index.asp

1.1 Package Contents

ASRock G31M-GS / G31M-S Motherboard

(Micro ATX Form Factor: 9.6-in x 7.5-in, 24.4 cm x 19.1 cm) ASRock G31M-GS / G31M-S Quick Installation Guide ASRock G31M-GS / G31M-S Support CD

One 80-conductor Ultra ATA 66/100 IDE Ribbon Cable (Optional) One Serial ATA (SATA) Data Cable (Optional)

One Serial ATA (SATA) HDD Power Cable (Optional) One I/O Panel Shield

hsilgnE

4

ASRock G31M-GS / G31M-S Motherboard

1.2Specifications

Platform

- Micro ATX Form Factor: 9.6-in x 7.5-in, 24.4 cm x 19.1 cm

CPU

- LGA 775 for Intel® CoreTM 2 Extreme / CoreTM 2 Quad / CoreTM

 

2 Duo / Pentium® Dual Core / Celeron® Dual Core / Celeron®,

 

supporting Penryn Quad Core Yorkfield and Dual Core

 

Wolfdale processors

 

- Compatible with all FSB1600/1333/1066/800MHz CPUs

 

(see CAUTION 1)

 

- Supports Hyper-Threading Technology (see CAUTION 2)

 

- Supports Untied Overclocking Technology (see CAUTION 3)

 

- Supports EM64T CPU

Chipset

- Northbridge: Intel® G31

 

- Southbridge: Intel® ICH7

Memory

- Dual Channel DDR2 Memory Technology (see CAUTION 4)

 

- 2 x DDR2 DIMM slots

 

- Supports DDR2 800/667 non-ECC, un-buffered memory

 

(see CAUTION 5)

 

- Max. capacity of system memory: 8GB (see CAUTION 6)

Expansion Slot

- 1 x PCI Express x16 slot

 

- 1 x PCI Express x1 slot

 

- 2 x PCI slots

 

 

Graphics

- Intel® Graphics Media Accelerator 3100

 

- Pixel Shader 2.0, DirectX 9.0

 

- Max. shared memory 384MB (see CAUTION 7)

Audio

- 5.1 CH Windows® VistaTM Premium Level HD Audio

 

(Realtek ALC662 Audio Codec)

 

 

LAN

- G31M-GS

 

Realtek PCIE x 1 Gigabit LAN RTL8111DL,

 

speed 10/100/1000 Mb/s

 

- G31M-S

 

Realtek PCIE x1 LAN 8102EL, speed 10/100 Mb/s

 

- Supports Wake-On-LAN

Rear Panel I/O

I/O Panel

 

- 1 x PS/2 Mouse Port

 

- 1 x PS/2 Keyboard Port

 

- 1 x Serial Port: COM1

 

- 1 x VGA Port

 

- 4 x Ready-to-Use USB 2.0 Ports

 

- 1 x RJ-45 LAN Port

 

- HD Audio Jack: Line in / Front Speaker / Microphone

 

 

English

5

ASRock G31M-GS / G31M-S Motherboard

hsilgnE

6

Connector

- 4 x SATAII 3.0 Gb/s connectors (No Support for RAID and

 

“Hot Plug” functions) (see CAUTION 8)

 

- 1 x ATA100 IDE connector (supports 2 x IDE devices)

 

- 1 x Floppy connector

 

- 1 x Print port header

 

- CPU/Chassis FAN connector

 

- 24 pin ATX power connector

 

- 4 pin 12V power connector

 

- CD in header

 

- Front panel audio connector

 

- 2 x USB 2.0 headers (support 4 USB 2.0 ports)

 

(see CAUTION 9)

BIOS Feature

- 4Mb AMI BIOS

 

- AMI Legal BIOS

 

- Supports “Plug and Play”

 

- ACPI 1.1 Compliance Wake Up Events

 

- Supports jumperfree

 

- AMBIOS 2.3.1 Support

 

- Supports Smart BIOS

Support CD

- Drivers, Utilities, AntiVirus Software (Trial Version)

Unique Feature

- ASRock OC Tuner (see CAUTION 10)

 

- Intelligent Energy Saver (see CAUTION 11)

 

- Hybrid Booster:

 

- CPU Frequency Stepless Control (see CAUTION 12)

 

- ASRock U-COP (see CAUTION 13)

 

- Boot Failure Guard (B.F.G.)

Hardware

- CPU Temperature Sensing

Monitor

- Chassis Temperature Sensing

 

- CPU Fan Tachometer

 

- Chassis Fan Tachometer

 

- CPU Quiet Fan

 

- Voltage Monitoring: +12V, +5V, +3.3V, Vcore

 

 

OS

- Microsoft® Windows® 2000 / XP / XP 64-bit / VistaTM /

 

VistaTM 64-bit compliant

Certifications

- FCC, CE

* For detailed product information, please visit our website: http://www.asrock.com

ASRock G31M-GS / G31M-S Motherboard

WARNING

Please realize that there is a certain risk involved with overclocking, including adjusting the setting in the BIOS, applying Untied Overclocking Technology, or using the third-party overclocking tools. Overclocking may affect your system stability, or even cause damage to the components and devices of your system. It should be done at your own risk and expense. We are not responsible for possible damage caused by overclocking.

CAUTION!

1.

FSB1600-CPU will operate in overclocking mode. Under this situation,

 

PCIE frequency will also be overclocked to 120MHz. Besides, if you

 

want to overclock the CPU you adopt from FSB800 to FSB1066, you

 

need to adjust the jumpers. Please refer to page 15 for proper jumper

 

settings.

 

 

2.

About the setting of “Hyper Threading Technology”, please check page

 

32 of “User Manual” in the support CD.

3.

This motherboard supports Untied Overclocking Technology. Please read

 

“Untied Overclocking Technology” on page 20 for details.

4.

This motherboard supports Dual Channel Memory Technology. Before

 

you implement Dual Channel Memory Technology, make sure to read

 

the installation guide of memory modules on page 12 for proper

 

installation.

 

 

5.

Please check the table below for the CPU FSB frequency and its

 

corresponding memory support frequency.

 

CPU FSB Frequency

Memory Support Frequency

 

 

1600

DDR2 800

 

 

1333

DDR2 667, DDR2 800

 

 

1066

DDR2 667, DDR2 800

 

 

800

DDR2 667, DDR2 800

 

6.

Due to the operating system limitation, the actual memory size may be

 

less than 4GB for the reservation for system usage under Windows® XP

 

and Windows® VistaTM. For Windows® XP 64-bit and Windows® VistaTM

 

64-bit with 64-bit CPU, there is no such limitation.

7.

The maximum shared memory size is defined by the chipset vendor

 

and is subject to change. Please check Intel® website for the latest

 

information.

 

 

8.

Before installing SATAII hard disk to SATAII connector, please read the “SATAII

 

Hard Disk Setup Guide” on page 24 of “User Manual” in the support CD to

 

adjust your SATAII hard disk drive to SATAII mode. You can also connect

 

SATA hard disk to SATAII connector directly.

9.

Power Management for USB 2.0 works fine under Microsoft® Windows®

 

VistaTM 64-bit / VistaTM / XP 64-bit / XP SP1 or SP2 / 2000 SP4.

10.

It is a user-friendly ASRock overclocking tool which allows you to surveil

 

your system by hardware monitor function and overclock your hardware

 

devices to get the best system performance under Windows®

 

environment. Please visit our website for the operation procedures of

 

ASRock OC Tuner. ASRock website: http://www.asrock.com

English

7

ASRock G31M-GS / G31M-S Motherboard

11.Featuring an advanced proprietary hardware and software design, Intelligent Energy Saver is a revolutionary technology that delivers unparalleled power savings. In other words, it is able to provide exceptional power saving and improve power efficiency without sacrificing computing performance. Please visit our website for the operation procedures of Intelligent Energy Saver.

ASRock website: http://www.asrock.com

12.Although this motherboard offers stepless control, it is not recommended to perform over-clocking. Frequencies other than the recommended CPU bus frequencies may cause the instability of the system or damage the CPU.

13.While CPU overheat is detected, the system will automatically shutdown. Before you resume the system, please check if the CPU fan on the motherboard functions properly and unplug the power cord, then plug it back again. To improve heat dissipation, remember to spray thermal grease between the CPU and the heatsink when you install the PC system.

hsilgnE

8

ASRock G31M-GS / G31M-S Motherboard

2. Installation

Pre-installation Precautions

Take note of the following precautions before you install motherboard components or change any motherboard settings.

1.Unplug the power cord from the wall socket before touching any component. Failure to do so may cause severe damage to the motherboard, peripherals, and/or components.

2.To avoid damaging the motherboard components due to static electricity, NEVER place your motherboard directly on the carpet or the like. Also remember to use a grounded wrist strap or touch a safety grounded object before you handle components.

3.Hold components by the edges and do not touch the ICs.

4.Whenever you uninstall any component, place it on a grounded antstatic pad or in the bag that comes with the component.

5.When placing screws into the screw holes to secure the motherboard to the chassis, please do not over-tighten the screws! Doing so may damage the motherboard.

2.1CPU Installation

For the installation of Intel 775-LAND CPU, please follow the steps below.

775-Pin Socket Overview

Before you insert the 775-LAND CPU into the socket, please check if the CPU surface is unclean or if there is any bent pin on the socket. Do not force to insert the CPU into the socket if above situation is found. Otherwise, the CPU will be seriously damaged.

English

9

ASRock G31M-GS / G31M-S Motherboard

Step 1. Open the socket:

Step 1-1. Disengaging the lever by depressing down and out on the hook to clear retention tab.

hsilgnE

Step 1-2. Rotate the load lever to fully open position at approximately 135 degrees.

Step 1-3. Rotate the load plate to fully open position at approximately 100 degrees.

Step 2. Insert the 775-LAND CPU:

Step 2-1. Hold the CPU by the edges where are marked with black lines.

Step 2-2. Orient the CPU with IHS (Integrated Heat Sink) up. Locate Pin1 and the two orientation key notches.

lineblack

lineblack

Pin1

 

Pin1

 

 

 

alignment key

orientation

orientation

alignment key

 

 

key notch

key notch

 

 

 

 

 

775-Pin Socket

 

775-LAND CPU

 

 

For proper inserting, please ensure to match the two orientation key notches of the CPU with the two alignment keys of the socket.

Step 2-3. Carefully place the CPU into the socket by using a purely vertical motion.

Step 2-4. Verify that the CPU is within the socket and properly mated to the orient keys.

Step 3. Remove PnP Cap (Pick and Place Cap):

Use your left hand index finger and thumb to support the load plate edge, engage PnP cap with right hand thumb and peel the cap from the socket while pressing on center of PnP cap to assist in removal.

1 0

ASRock G31M-GS / G31M-S Motherboard

1.It is recommended to use the cap tab to handle and avoid kicking off the PnP cap.

2.This cap must be placed if returning the motherboard for after service.

Step 4. Close the socket:

Step 4-1. Rotate the load plate onto the IHS. Step 4-2. While pressing down lightly on load

plate, engage the load lever.

Step 4-3. Secure load lever with load plate tab under retention tab of load lever.

2.2Installation of CPU Fan and Heatsink

For proper installation, please kindly refer to the instruction manuals of your CPU fan and heatsink.

Below is an example to illustrate the installation of the heatsink for 775-LAND CPU. Step 1. Apply thermal interface material onto center

of IHS on the socket surface.

Step 2.

Place the heatsink onto the socket. Ensure

 

fan cables are oriented on side closest to the

 

CPU fan connector on the motherboard

 

(CPU_FAN1, see page 2, No. 4).

Step 3.

Align fasteners with the motherboard

 

throughholes.

Step 4.

Rotate the fastener clockwise, then press

 

down on fastener caps with thumb to install

 

and lock. Repeat with remaining fasteners.

 

 

 

If you press down the fasteners without rotating them clockwise,

 

the heatsink cannot be secured on the motherboard.

 

 

Step 5.

Connect fan header with the CPU fan

 

connector on the motherboard.

Step 6.

Secure excess cable with tie-wrap to ensure

 

cable does not interfere with fan operation or

 

contact other components.

1 1

English

ASRock G31M-GS / G31M-S Motherboard

hsilgnE

2.3 Installation of Memory Modules (DIMM)

G31M-GS / G31M-S motherboard provides two 240-pin DDR2 (Double Data Rate 2) DIMM slots, and supports Dual Channel Memory Technology. For dual channel configuration, you always need to install two identical (the same brand, speed, size and chip-type) memory modules in the DDR2 DIMM slots to activate Dual Channel Memory Technology. Otherwise, it will operate at single channel mode.

1.It is not allowed to install a DDR memory module into DDR2 slot; otherwise, this motherboard and DIMM may be damaged.

2.If you install only one memory module or two non-identical memory modules, it is unable to activate the Dual Channel Memory Technology.

Installing a DIMM

Please make sure to disconnect power supply before adding or removing DIMMs or the system components.

Step 1. Unlock a DIMM slot by pressing the retaining clips outward.

Step 2. Align a DIMM on the slot such that the notch on the DIMM matches the break on the slot.

The DIMM only fits in one correct orientation. It will cause permanent damage to the motherboard and the DIMM if you force the DIMM into the slot at incorrect orientation.

Step 3. Firmly insert the DIMM into the slot until the retaining clips at both ends fully

snap back in place and the DIMM is properly seated.

1 2

ASRock G31M-GS / G31M-S Motherboard

2.4 Expansion Slots (PCI and PCI Express Slots)

There are 2 PCI slots and 2 PCI Express slots on this motherboard.

PCI slots: PCI slots are used to install expansion cards that have the 32-bit PCI interface.

PCIE slots:

PCIE1 (PCIE x1 slot) is used for PCI Express cards with x1 lane width cards, such as Gigabit LAN card, SATA2 card, etc.

PCIE2 (PCIE x16 slot) is used for PCI Express cards with x16 lane width graphics cards.

If you install the add-on PCI Express VGA card to PCIE2 (PCIE x16 slot), the onboard VGA will be disabled. If you install the add-on PCI Express VGA card to PCIE2 (PCIE x16 slot) and adjust the “Internal Graphics Mode Select” BIOS option to [Enabled], the onboard VGA will be enabled, and the primary screen will be onboard VGA.

Installing an expansion card

Step 1. Before installing the expansion card, please make sure that the power supply is switched off or the power cord is unplugged. Please read the documentation of the expansion card and make necessary hardware

settings for the card before you start the installation.

Step 2. Remove the bracket facing the slot that you intend to use. Keep the screws for later use.

Step 3. Align the card connector with the slot and press firmly until the card is completely seated on the slot.

Step 4. Fasten the card to the chassis with screws.

English

1 3

ASRock G31M-GS / G31M-S Motherboard

2.5 Jumpers Setup

The illustration shows how jumpers are

 

 

setup. When the jumper cap is placed on

 

 

pins, the jumper is “Short”. If no jumper cap

 

 

is placed on pins, the jumper is “Open”. The

 

 

illustration shows a 3-pin jumper whose pin1

Short

Open

and pin2 are “Short” when jumper cap is

 

 

placed on these 2 pins.

 

 

 

Jumper

Setting

 

Description

PS2_USB_PWR1

 

 

Short pin2, pin3 to enable

(see p.2 No. 1)

 

 

+5VSB (standby) for PS/2

 

 

 

or USB wake up events.

Note: To select +5VSB, it requires 2 Amp and higher standby current provided by power supply.

Clear CMOS

(CLRCMOS1, 2-pin jumper)

(see p.2 No. 8)

2-pin jumper

Note: CLRCMOS1 allows you to clear the data in CMOS. The data in CMOS includes system setup information such as system password, date, time, and system setup parameters. To clear and reset the system parameters to default setup, please turn off the computer and unplug the power cord from the power supply. After waiting for 15 seconds, use a jumper cap to short 2 pins on CLRCMOS1 for 5 seconds.

hsilgnE

1 4

ASRock G31M-GS / G31M-S Motherboard

OC 800 / FSB0 / FSB1 Jumper

(OC 800 / FSB0 / FSB1, 3-pin jumper,

see p.2 No. 27)

Default

Note: If you want to overclock the FSB800-CPU (e.g. Cel400, E1000, E2000, E4000, E5000, E6000 series CPU) to FSB1066 on this motherboard, you need to adjust the jumpers. Please short pin2, pin3 for OC800 jumper. Otherwise, the CPU may not work properly on this motherboard. Please refer to below jumper settings.

English

1 5

ASRock G31M-GS / G31M-S Motherboard

hsilgnE

2.6 Onboard Headers and Connectors

Onboard headers and connectors are NOT jumpers. Do NOT place jumper caps over these headers and connectors. Placing jumper caps over the headers and connectors will cause permanent damage of the motherboard!

FDD connector

(33-pin FLOPPY1)

(see p.2 No. 20)

the red-striped side to Pin1

Note: Make sure the red-striped side of the cable is plugged into Pin1 side of the connector.

Primary IDE connector (Blue)

(39-pin IDE1, see p.2 No. 7)

connect the blue end

 

 

connect the black end

to the motherboard

 

 

to the IDE devices

 

80-conductor ATA 66/100 cable

Note: Please refer to the instruction of your IDE device vendor for the details.

 

 

 

 

Serial ATAII Connectors

3

4

These Serial ATAII (SATAII)

(SATAII_1: see p.2, No. 13)

connectors support SATAII

SATAII

SATAII

(SATAII_2: see p.2, No. 12)

or SATA hard disk for internal

 

 

(SATAII_3: see p.2, No. 10)

1

2

storage devices. The current

(SATAII_4: see p.2, No. 11)

SATAII interface allows up to

SATAII

SATAII

 

3.0 Gb/s data transfer rate.

 

 

 

 

 

 

 

Serial ATA (SATA)

 

 

Either end of the SATA data cable

Data Cable

 

 

can be connected to the SATA /

(Optional)

 

 

SATAII hard disk or the SATAII

 

 

 

connector on the motherboard.

Serial ATA (SATA) Power Cable

(Optional)

connect to the SATA

HDD power connector

connect to the powersupply

Please connect the black end of SATA power cable to the power connector on each drive. Then connect the white end of SATA power cable to the power connector of the power supply.

1 6

ASRock G31M-GS / G31M-S Motherboard

USB 2.0 Headers

Besides four default USB 2.0

(9-pin USB6_7)

ports on the I/O panel, there are

(see p.2 No. 15)

two USB 2.0 headers on this

 

motherboard. Each USB 2.0

 

header can support two USB

 

2.0 ports.

(9-pin USB4_5)

 

(see p.2 No. 16)

 

Print Port Header

This is an interface for print

(25-pin LPT1)

port cable that allows

(see p.2 No. 26)

convenient connection of printer

 

devices.

Internal Audio Connector

 

This connector allows you

(4-pin CD1)

CD1

to receive stereo audio input

(CD1: see p.2 No. 23)

from sound sources such as

 

 

a CD-ROM, DVD-ROM, TV

 

 

tuner card, or MPEG card.

 

 

 

Front Panel Audio Header

 

This is an interface for front

(9-pin HD_AUDIO1)

 

panel audio cable that allows

(see p.2 No. 21)

 

convenient connection and

 

 

control of audio devices.

1.High Definition Audio supports Jack Sensing, but the panel wire on the chassis must support HDA to function correctly. Please follow the instruction in our manual and chassis manual to install your system.

2.If you use AC’97 audio panel, please install it to the front panel audio header as below:

A.Connect Mic_IN (MIC) to MIC2_L.

B.Connect Audio_R (RIN) to OUT2_R and Audio_L (LIN) to OUT2_L.

C.Connect Ground (GND) to Ground (GND).

English

1 7

ASRock G31M-GS / G31M-S Motherboard

D.MIC_RET and OUT_RET are for HD audio panel only. You don’t need to connect them for AC’97 audio panel.

E.Enter BIOS Setup Utility. Enter Advanced Settings, and then select Chipset Configuration. Set the Front Panel Control option from [Auto] to [Enabled].

F.Enter Windows system. Click the icon on the lower right hand taskbar to enter Realtek HD Audio Manager.

For Windows® 2000 / XP / XP 64-bit OS:

Click “Audio I/O”, select “Connector Settings” , choose

“Disable front panel jack detection”, and save the change by

clicking “OK”.

 

For Windows® VistaTM / VistaTM 64-bit OS:

 

Click the right-top “Folder” icon

, choose “Disable front

panel jack detection”, and save the change by clicking “OK”. G. To activate the front mic.

For Windows® 2000 / XP / XP 64-bit OS:

Please select “Front Mic” as default record device.

If you want to hear your voice through front mic, please deselect "Mute" icon in “Front Mic” of “Playback” portion.

For Windows® VistaTM / VistaTM 64-bit OS:

Go to the "Front Mic" Tab in the Realtek Control panel.

Click "Set Default Device" to make the Front Mic as the default record device.

System Panel Header

This header accommodates

(9-pin PANEL1)

several system front panel

(see p.2 No. 17)

functions.

hsilgnE

Chassis Speaker Header

 

Please connect the chassis

(4-pin SPEAKER 1)

 

speaker to this header.

(see p.2 No. 14)

 

 

 

 

 

Chassis Fan Connector

 

Please connect a chassis fan

(3-pin CHA_FAN1)

 

cable to this connector and

(see p.2 No. 19)

 

match the black wire to the

 

 

ground pin.

 

 

 

CPU Fan Connector

4 3 2 1

Please connect a CPU fan cable

(4-pin CPU_FAN1)

 

to this connector and match

(see p.2 No. 4)

 

the black wire to the ground pin.

1 8

ASRock G31M-GS / G31M-S Motherboard

Though this motherboard provides 4-Pin CPU fan (Quiet Fan) support, the 3-Pin CPU fan still can work successfully even without the fan speed control function. If you plan to connect the 3-Pin CPU fan to the CPU fan connector on this motherboard, please connect it to Pin 1-3.

Pin 1-3 Connected

3-Pin Fan Installation

ATX Power Connector

12

24

Please connect an ATX power

(24-pin ATXPWR1)

 

 

supply to this connector.

 

(see p.2

No. 6)

 

 

 

 

 

 

 

 

1

13

 

 

 

 

 

 

 

 

 

 

Though this motherboard provides 24-pin ATX power connector,

12

24

 

 

it can still work if you adopt a traditional 20-pin ATX power supply.

 

 

 

 

To use the 20-pin ATX power supply, please plug your power

 

 

 

 

supply along with Pin 1 and Pin 13.

 

 

 

 

 

 

 

20-PinATX Power Supply Installation

1

13

 

 

 

 

 

 

 

 

 

ATX 12V Connector

 

 

Please note that it is necessary

(4-pin ATX12V1)

 

 

to connect a power supply with

(see p.2

No. 28)

 

 

ATX 12V plug to this connector

 

 

 

 

 

so that it can provides sufficient

 

 

 

 

 

power. Failing to do so will cause

 

 

 

 

 

the failure to power up.

 

English

1 9

ASRock G31M-GS / G31M-S Motherboard

2.7 Serial ATA (SATA) / Serial ATAII (SATAII) Hard Disks Installation

This motherboard adopts Intel® ICH7 south bridge chipset that supports Serial ATA (SATA) / Serial ATAII (SATAII) hard disks. You may install SATA / SATAII hard disks on this motherboard for internal storage devices. This section will guide you to install the SATA / SATAII hard disks.

STEP 1: Install the SATA / SATAII hard disks into the drive bays of your chassis. STEP 2: Connect the SATA power cable to the SATA / SATAII hard disk.

STEP 3: Connect one end of the SATA data cable to the motherboard’s SATAII connector.

STEP 4: Connect the other end of the SATA data cable to the SATA / SATAII hard disk.

2.8 Driver Installation Guide

To install the drivers to your system, please insert the support CD to your optical drive first. Then, the drivers compatible to your system can be auto-detected and listed on the support CD driver page. Please follow the order from up to bottom side to install those required drivers. Therefore, the drivers you install can work properly.

2.9 Untied Overclocking Technology

This motherboard supports Untied Overclocking Technology, which means during overclocking, FSB enjoys better margin due to fixed PCI / PCIE buses. Before you enable Untied Overclocking function, please enter “Overclock Mode” option of BIOS setup to set the selection from [Auto] to [CPU, PCIE, Async.]. Therefore, CPU FSB is untied during overclocking, but PCI / PCIE buses are in the fixed mode so that FSB can operate under a more stable overclocking environment.

Please refer to the warning on page 7 for the possible overclocking risk before you apply Untied Overclocking Technology.

hsilgnE

2 0

ASRock G31M-GS / G31M-S Motherboard

3. BIOS Information

The Flash Memory on the motherboard stores BIOS Setup Utility. When you start up the computer, please press <F2> during the Power-On-Self-Test (POST) to enter BIOS Setup utility; otherwise, POST continues with its test routines. If you wish to enter BIOS Setup after POST, please restart the system by pressing <Ctl> + <Alt> + <Delete>, or pressing the reset button on the system chassis. The BIOS Setup program is designed to be user-friendly. It is a menu-driven program, which allows you to scroll through its various sub-menus and to select among the predetermined choices. For the detailed information about BIOS Setup, please refer to the User Manual (PDF file) contained in the Support CD.

4. Software Support CD information

This motherboard supports various Microsoft® Windows® operating systems: 2000 / XP / XP 64-bit / VistaTM / VistaTM 64-bit. The Support CD that came with the motherboard contains necessary drivers and useful utilities that will enhance motherboard features. To begin using the Support CD, insert the CD into your CD-ROM drive. It will display the Main Menu automatically if “AUTORUN” is enabled in your computer. If the Main Menu does not appear automatically, locate and double-click on the file “ASSETUP. EXE” from the BIN folder in the Support CD to display the menus.

English

2 1

ASRock G31M-GS / G31M-S Motherboard

1. Einführung

Wir danken Ihnen für den Kauf des ASRock G31M-GS / G31M-S Motherboard, ein zuverlässiges Produkt, welches unter den ständigen, strengen Qualitätskontrollen von ASRock gefertigt wurde. Es bietet Ihnen exzellente Leistung und robustes Design, gemäß der Verpflichtung von ASRock zu Qualität und Halbarkeit.

Diese Schnellinstallationsanleitung führt in das Motherboard und die schrittweise Installation ein. Details über das Motherboard finden Sie in der Bedienungsanleitung auf der Support-CD.

Da sich Motherboard-Spezifikationen und BIOS-Software verändern können, kann der Inhalt dieses Handbuches ebenfalls jederzeit geändert werden. Für den Fall, dass sich Änderungen an diesem Handbuch ergeben, wird eine neue Version auf der ASRock-Website, ohne weitere Ankündigung, verfügbar sein. Die neuesten Grafikkarten und unterstützten CPUs sind auch auf der ASRock-Website aufgelistet.

ASRock-Website: http://www.asrock.com

Wenn Sie technische Unterstützung zu Ihrem Motherboard oder spezifische Informationen zu Ihrem Modell benötigen, besuchen Sie bitte unsere Webseite:

www.asrock.com/support/index.asp

1.1 Kartoninhalt

ASRock G31M-GS / G31M-S Motherboard

(Micro ATX-Formfaktor: 24.4 cm x 19.1 cm; 9.6 Zoll x 7.5 Zoll) ASRock G31M-GS / G31M-S Schnellinstallationsanleitung ASRock G31M-GS / G31M-S_ Support-CD

Ein 80-adriges Ultra-ATA 66/100 IDE-Flachbandkabel (Option) Ein Seriell-ATA- (SATA) Datenkabel (Option)

Ein Seriell-ATA (SATA) Festplattennetzkabel (Option) Ein I/O Shield

Deutsch

2 2

ASRock G31M-GS / G31M-S Motherboard

1.2 Spezifikationen

Plattform

- Micro ATX-Formfaktor: 24.4 cm x 19.1 cm; 9.6 Zoll x 7.5 Zoll

CPU

- LGA 775 für Intel® CoreTM 2 Extreme / CoreTM 2 Quad / CoreTM

 

2 Duo / Pentium® Dual Core / Celeron® Dual Core / Celeron®

 

unterstützt Penryn Quad Core Yorkfield und Dual Core

 

Wolfdale Prozessoren

 

- Kompatibilität mit FSB1600/1333/1066/800 MHz

 

(siehe VORSICHT 1)

 

- Unterstützt Hyper-Threading-Technologie

 

(siehe VORSICHT 2)

 

- Unterstützt Untied-Übertaktungstechnologie

 

(siehe VORSICHT 3)

 

- Unterstützt EM64T-CPU

 

 

Chipsatz

- Northbridge: Intel® G31

 

- Southbridge: Intel® ICH7

Speicher

- Unterstützung von Dual-Kanal-DDR2-Speichertechnologie

 

(siehe VORSICHT 4)

 

- 2 x Steckplätze für DDR2

 

- Unterstützt DDR2 800/667 non-ECC, ungepufferter Speicher

 

(siehe VORSICHT 5)

 

- Max. Kapazität des Systemspeichers: 8GB

 

(siehe VORSICHT 6)

 

 

Erweiterungs-

- 1 x PCI Express x16-Steckplätze

steckplätze

- 1 x PCI Express x1-Steckplätze

 

- 2 x PCI -Steckplätze

 

 

Onboard-VGA

- Intel® Graphics Media Accelerator 3100

 

- Pixel Shader 2.0, DX9.0 VGA

 

- Maximal gemeinsam genutzter Speicher 384MB

 

(siehe VORSICHT 7)

 

 

Audio

- 5.1 CH Windows® VistaTM Premium Level HD Audio

 

(ALC662 Audio Codec)

LAN

- G31M-GS

 

Realtek PCIE x 1 Gigabit LAN RTL8111DL,

 

speed 10/100/1000 Mb/s

 

- G31M-S

 

Realtek PCIE x1 LAN 8102EL, speed 10/100 Mb/s

 

- Unterstützt Wake-On-LAN

 

 

E/A-Anschlüsse

I/O Panel

an der

- 1 x PS/2 Mouse Port

Rückseite

- 1 x PS/2 Keyboard Port

Deutsch

2 3

ASRock G31M-GS / G31M-S Motherboard

Deutsch

 

- 1 x Serieller port: COM 1

 

- 1 x VGA Port

 

- 4 x Ready-to-Use USB 2.0 Ports

 

- 1 x RJ-45 Port

 

- Audioanschlüsse: Line In / Line Out / Mikrofon

Anschlüsse

- 4 x SATAII-Anschlüsse, unterstützt bis 3.0 Gb/s

 

Datenübertragungsrate (Unterstützt keine “RAID”- und “Hot-

 

Plug”-Funktionen) (siehe VORSICHT 8)

 

- 1 x ATA100 IDE-Anschlüsse (Unterstützt bis 2 IDE-Geräte)

 

- 1 x FDD-Anschlüsse

 

- 1 x Druckerport-Anschlussleiste

 

- CPU/Gehäuse-Lüfteranschluss

 

- 24-pinATX-Netz-Header

 

- 4-pin anschluss für 12V-ATX-Netzteil

 

- Interne Audio-Anschlüsse

 

- Anschluss für Audio auf der Gehäusevorderseite

 

- 2 x USB 2.0 Buchse (unterstützt 4 USB 2.0 Ports)

 

(siehe VORSICHT 9)

BIOS

- 4Mb AMI BIOS

 

- AMI legal BIOS mit Unterstützung für “Plug and Play”

 

- ACPI 1.1-Weckfunktionen

 

- JumperFree-Modus

 

- SMBIOS 2.3.1

 

- Unterstützt Smart BIOS

Support-CD

- Treiber, Dienstprogramme, Antivirussoftware

 

(Probeversion)

Einzigartige

- ASRock OC Tuner (siehe VORSICHT 10)

Eigenschaft

- Intelligent Energy Saver (Intelligente Energiesparfunktion)

 

(siehe VORSICHT 11)

 

- Hybrid Booster:

 

- Schrittloser CPU-Frequenz-Kontrolle

 

(siehe VORSICHT 12)

 

- ASRock U-COP (siehe VORSICHT 13)

 

- Boot Failure Guard (B.F.G. – Systemstartfehlerschutz)

Hardware Monitor - Überwachung der CPU-Temperatur

 

- Motherboardtemperaturerkennung

 

- Drehzahlmessung für CPU-Lüfter

 

- Drehzahlmessung für Gehäuselüfter

 

- CPU-Lüftergeräuschdämpfung

 

- Spannungsüberwachung: +12V, +5V, +3.3V, Vcore

 

 

Betriebssysteme

- Unterstützt Microsoft® Windows® 2000 / XP / XP 64-Bit /

 

VistaTM / VistaTM 64-Bit

Zertifizierungen

- FCC, CE

2 4

ASRock G31M-GS / G31M-S Motherboard

*Für die ausführliche Produktinformation, besuchen Sie bitte unsere Website: http://www.asrock.com

WARNUNG

Beachten Sie bitte, dass Overclocking, einschließlich der Einstellung im BIOS, Anwenden der Untied Overclocking-Technologie oder Verwenden von Overclocking-Werkzeugen von Dritten, mit einem gewissen Risiko behaftet ist. Overclocking kann sich nachteilig auf die Stabilität Ihres Systems auswirken oder sogar Komponenten und Geräte Ihres Systems beschädigen. Es geschieht dann auf eigene Gefahr und auf Ihre Kosten. Wir übernehmen keine Verantwortung für mögliche Schäden, die aufgrund von Overclocking verursacht wurden.

VORSICHT!

1. FSB1600-CPU wird im Übertaktmodus laufen. In diesem Fall wird die PCIE-Frequenz auf 120 MHz übertaktet. Möchten Sie zudem die CPU übertakten, die Sie von FSB800 auf FSB1066 anheben, müssen Sie Jumper umsetzen. Die geeigneten Jumper-Einstellungen sind auf Seite 28 aufgelistet.

2. Die Einstellung der “Hyper-Threading Technology”, finden Sie auf Seite 32 des auf der Support-CD enthaltenen Benutzerhandbuches beschrieben.

3. Dieses Motherboard unterstützt die Untied-Übertaktungstechnologie. Unter “Entkoppelte Übertaktungstechnologie” auf Seite 20 finden Sie detaillierte Informationen.

4. Dieses Motherboard unterstützt Dual-Kanal-Speichertechnologie. Vor Implementierung der Dual-Kanal-Speichertechnologie müssen Sie die Installationsanleitung für die Speichermodule auf Seite 12 zwecks richtiger Installation gelesen haben.

5. Die unterstützten Arbeitsspeicherfrequenzen und die entsprechende CPU FSB-Frequenz entnehmen Sie bitte der nachstehenden Tabelle.

CPU FSB-Frequenz

Unterstützte Arbeitsspeicherfrequenz

1600

DDR2 800

1333

DDR2 667, DDR2 800

1066

DDR2 667, DDR2 800

800

DDR2 667, DDR2 800

6. Durch Betriebssystem-Einschränkungen kann die tatsächliche Speichergröße weniger als 4 GB betragen, da unter Windows® XP und Windows® Vista™ etwas Speicher zur Nutzung durch das System reserviert wird. Unter Windows® XP 64-bit und Windows® Vista64-bit mit 64-Bit-CPU besteht diese Einschränkung nicht.

7. Die Maximalspeichergröße ist von den Chipshändler definiert und umgetauscht. Bitte überprüfen Sie Intel® website für die neuliche Information.

Deutsch

2 5

ASRock G31M-GS / G31M-S Motherboard

8.Vor Installation der SATAII-Festplatte an den SATAII-Anschluss lesen Sie bitte “Setup-Anleitung für SATAII-Festplatte” auf Seite 24 der “Bedienungsanleitung” auf der Support-CD, um Ihre SATAII-Festplatte dem SATAII-Modus anzugleichen. Sie können die SATA-Festplatte auch direkt mit dem SATAII-Anschluss verbinden.

9.Das Power Management für USB 2.0 arbeitet unter Microsoft® Windows® VistaTM 64-Bit / VistaTM / XP 64-Bit / XP SP1 oder SP2/2000 SP4 einwandfrei.

10.Es ist ein benutzerfreundlicher ASRock Übertaktenswerkzeug, das erlaubt, dass Sie Ihr System durch den Hardware-Monitor Funktion zu überblicken und Ihre Hardware-Geräte übertakten, um die beste Systemleistung unter der Windows® Umgebung zu erreichen. Besuchen Sie bitte unsere Website für die Operationsverfahren von ASRock OC Tuner. ASRock-Website: http://www.asrock.com

11.Mit einem fortschrittlichen, eigenständigen Hardund Softwaredesign nutzt der Intelligent Energy Saver eine revolutionäre Technologie, die bisher unerreichte Energieeinsparungen ermöglicht. Mit anderen Worten: Sie verbrauchen besonders wenig Energie und erreichen einen hohen Wirkungsgrad, ohne dass dies zu Lasten der Rechenleistung geht. Auf unseren Internetseiten finden Sie einige Erläuterungen zur Funktionsweise des Intelligent Energy Saver.

ASRock-Website: http://www.asrock.com

12.Obwohl dieses Motherboard stufenlose Steuerung bietet, wird Overclocking nicht empfohlen. Frequenzen, die von den empfohlenen CPU-Busfrequenzen abweichen, können Instabilität des Systems verursachen oder die CPU beschädigen.

13.Wird eine Überhitzung der CPU registriert, führt das System einen automatischen Shutdown durch. Bevor Sie das System neu starten, prüfen Sie bitte, ob der CPU-Lüfter am Motherboard richtig funktioniert, und stecken Sie bitte den Stromkabelstecker aus und dann wieder ein. Um die Wärmeableitung zu verbessern, bitte nicht vergessen, etwas Wärmeleitpaste zwischen CPU und Kühlkörper zu sprühen.

Deutsch

2 6

ASRock G31M-GS / G31M-S Motherboard

Hinweis:
Jumper
PS2_USB_PWR1
(siehe S.2 - No. 1)

1.3 Einstellung der Jumper

Die Abbildung verdeutlicht, wie Jumper gesetzt werden. Werden Pins durch Jumperkappen verdeckt, ist der Jumper “Gebrückt”. Werden keine Pins durch

Jumperkappen verdeckt, ist der Jumper Gebrückt Offen “Offen”. Die Abbildung zeigt einen 3-Pin

Jumper dessen Pin1 und Pin2 “Gebrückt” sind, bzw. es befindet sich eine JumperKappe auf diesen beiden Pins.

Einstellun Beschreibung

Überbrücken Sie Pin2, Pin3, um +5VSB (Standby) zu setzen und die PS/2 oder USBWeckfunktionen zu aktivieren.

Um +5VSB nutzen zu können, muss das Netzteil auf dieser Leitung 2A oder mehr leisten können.

CMOS löschen

(CLRCMOS1, 2-Pin jumper) (siehe S.2 - No. 8)

2-Pin jumper

Hinweis: Mit CLRCMOS1 können Sie die Daten im CMOS löschen. Die CMOS Daten beinhalten die Systeminformationen wie Systemkennwort, Datum, Zeit und System-Setupeinstellungen. Um die Einstellungen zu löschen und Default-Werte wiederherzustellen, schalten Sie den Computer aus, ziehen Sie den Netzstecker und überbrücken Sie 2-pin von CLRCMOS1 mithilfe des Jumpers für 5 Sekunden.

Deutsch

2 7

ASRock G31M-GS / G31M-S Motherboard

OC 800 / FSB0 / FSB1-Jumper

(OC 800 / FSB0 / FSB1, 3-pol. Jumper, siehe Seite 2, Nr. 27)

Default-Einstellung

Hinweis: Wenn Sie eine FSB800-CPU (z. B. CPUs der Serien Cel400, E1000, E2000, E4000, E5000, E6000) mit Ihrem Motherboard auf FSB1066 übertakten möchten, müssen Sie die entsprechenden Steckbrückeneinstellungen ändern. Schließen Sie den Pin 2 und den

Pin 3 des OC 800-Jumpers kurz. Anderfalls arbeitet die CPU eventuell nicht richtig mit dem Motherboard zusammen. Bitte schauen Sie sich die nachstehenden Steckbrückeneinstellungen an.

Deutsch

2 8

ASRock G31M-GS / G31M-S Motherboard

1.4 Integrierte Header und Anschlüsse

Integrierte Header und Anschlüsse sind KEINE Jumper. Setzen Sie ng KEINE Jumperkappen auf diese Header und Anschlüsse. Wenn Sie Jumperkappen auf Header und Anschlüsse setzen, wird das

Motherboard unreparierbar beschädigt!

Anschluss für das Floppy-Laufwerk

(33-Pin FLOPPY1)

die rotgestreifte Seite auf Stift 1

(siehe S.2 - No. 20)

Hinweis: Achten Sie darauf, dass die rotgestreifte Seite des Kabel mit der Stift 1- Seite des Anschlusses verbunden wird.

Primärer IDE-Anschluss (Blauer)

(39-pin IDE1, siehe S.2 - No. 7)

Blauer Anschluss

Schwarzer Anschluss

zum Motherboard

zur Festplatte

 

80-adriges ATA 66/100 Kabel

Hinweis: Details entnehmen Sie bitte den Anweisungen Ihres IDE-Gerätehändlers.

Seriell-ATAII-Anschlüsse

 

 

Diese vier Serial ATA

(SATAII_1: siehe S.2, Punkt 13)

3

4

(SATA II) -Anschlüsse

(SATAII_3: siehe S.2, Punkt 10)

_

_

oder SATA II-Festplatten. Die

SATAII

SATAII

(SATAII_2: siehe S.2, Punkt 12)

 

 

unterstützen interne SATA-

(SATAII_4: siehe S.2, Punkt 11)

1

2

aktuelle SATAII-Schnittstelle

 

_

_

ermöglicht eine

 

SATAII

SATAII

 

Datenübertragungsrate bis

 

 

 

3,0 Gb/s.

 

 

 

 

Serial ATA- (SATA-)

 

 

Sie können beide Enden des

Datenkabel

 

 

SATA-Datenkabels entweder

(Option)

 

 

mit der SATA / SATAII-

 

 

 

Festplatte oder

 

 

 

dem SATAII-Anschluss am

 

 

 

Mainboard verbinden.

2 9

Deutsch

ASRock G31M-GS / G31M-S Motherboard

Serial ATA- (SATA-) Stromversorgungskabel (Option)

Verbindung zum

SATA-HDD-Stromanschluss

Verbindung zum

Netzteil

Verbinden Sie bitte das schwarze Ende des SATAStromversorgungskabels mit dem Stromanschluss jedes Laufwerks. Verbinden Sie dann das weiße Ende des SATA-tromversorgungskabels mit dem Stromanschluss des Netzteils.

USB 2.0-Header

Zusätzlich zu den vier

(9-pol. USB6_7)

üblichen USB 2.0-Ports an den

(siehe S.2 - No. 15)

I/O-Anschlüssen befinden sich

 

zwei USB 2.0-Anschlussleisten

 

am Motherboard. Pro USB 2.0-

 

Anschlussleiste werden zwei

(9-pol. USB4_5)

USB 2.0-Ports unterstützt.

(siehe S.2 - No. 16)

 

Druckerport-Anschlussleiste

Dies ist eine Schnittstelle zum

(25-pol. LPT1)

Anschluss eines Druckerport-

(siehe S.2 - No. 26)

Kabels, mit dem Sie passende

 

Drucker auf einfache Weise

 

anschließen können.

Deutsch

Interne Audio-Anschlüsse

 

Diese ermöglichen Ihnen

(4-Pin CD1)

CD1

Stereo-Signalquellen, wie z. B.

(CD1: siehe S.2 - No. 23)

CD-ROM,DVD-ROM, TV-Tuner

 

 

 

oder MPEG-Karten mit Ihrem

 

 

System zu verbinden.

 

 

 

Anschluss für Audio auf

 

Dieses Interface zu einem

der Gehäusevorderseite

 

Audio-Panel auf der Vorderseite

(9-Pin HD_AUDIO1)

 

Ihres Gehäuses, ermöglicht

(siehe S.2 - No. 21)

 

Ihnen eine bequeme

 

 

Anschlussmöglichkeit und

 

 

Kontrolle über Audio-Geräte.

3 0

ASRock G31M-GS / G31M-S Motherboard

Loading...
+ 88 hidden pages