ASRock FM2A75M-ITX User Manual [en, ru, de, es, fr, it]

0 (0)

Copyright Notice:

No part of this installation guide may be reproduced, transcribed, transmitted, or translated in any language, in any form or by any means, except duplication of documentation by the purchaser for backup purpose, without written consent of ASRock Inc.

Products and corporate names appearing in this guide may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners’ benefit, without intent to infringe.

Disclaimer:

Specifications and information contained in this guide are furnished for informational use only and subject to change without notice, and should not be constructed as a commitment by ASRock. ASRock assumes no responsibility for any errors or omissions that may appear in this guide.

With respect to the contents of this guide, ASRock does not provide warranty of any kind, either expressed or implied, including but not limited to the implied warranties or conditions of merchantability or fitness for a particular purpose. In no event shall ASRock, its directors, officers, employees, or agents be liable for any indirect, special, incidental, or consequential damages (including damages for loss of profits, loss of business, loss of data, interruption of business and the like), even if ASRock has been advised of the possibility of such damages arising from any defect or error in the guide or product.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1)this device may not cause harmful interference, and

(2)this device must accept any interference received, including interference that may cause undesired operation.

CALIFORNIA, USA ONLY

The Lithium battery adopted on this motherboard contains Perchlorate, a toxic substance controlled in Perchlorate Best Management Practices (BMP) regulations passed by the California Legislature. When you discard the Lithium battery in California, USA, please follow the related regulations in advance.

“Perchlorate Material-special handling may apply, see www.dtsc.ca.gov/hazardouswaste/perchlorate

ASRock Website: http://www.asrock.com

Published September 2012

Copyright©2012 ASRock INC. All rights reserved.

1

English

ASRock FM2A75M-ITX Motherboard

ASRock FM2A75M-ITX User Manual

English

Motherboard Layout

1

 

 

2

 

 

 

 

 

3

 

 

 

 

CPU_FAN2

 

 

 

 

ATXPWR1

 

 

CPU_FAN1

 

 

 

 

 

 

 

SPEAKER1

4

 

 

 

 

 

 

 

 

 

1

 

 

 

 

 

 

DDR3_B1 (64 bit, 240-pin module)

 

 

 

25

 

 

 

 

 

 

 

 

 

 

5

CI1

 

 

 

 

DDR3_A1 (64 bit, 240-pin module)

 

 

 

1

 

 

 

 

CHA_FAN1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

DDR3 2600+

XFast RAM

 

6

 

USB 2.0

 

 

 

 

Dual Graphics

 

 

Ps2

T: USB0

CMOS Battery

 

 

 

 

 

 

 

Keyboard

B: USB1

 

 

 

 

 

 

 

7

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SOCKET FM2

 

PANEL 1

 

 

 

 

 

 

 

 

 

 

eSATA3

 

 

 

 

 

 

PLED PWRBTN

HDLED RESET

8

USB 2.0

 

 

 

 

 

 

 

T: USB2

 

 

 

 

 

 

 

B: USB3

 

 

 

 

 

 

1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1

 

 

 

 

 

 

 

 

 

 

USB_45

 

9

 

 

 

 

 

 

 

 

 

1

 

 

 

 

 

 

 

 

 

 

USB_67

 

10

USB 3.0

 

 

 

 

 

 

 

1

 

Top:

 

 

 

 

 

 

 

 

T: USB2

 

 

 

 

 

1

 

11

RJ-45

 

 

 

 

 

CIR1

 

B: USB3

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SATA3_4

SATA3_3

 

24

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

12

HDMI1

 

VGA1

 

 

 

 

 

 

SATA3_2

SATA3_1

13

 

 

 

 

 

 

 

DX11

 

 

 

 

 

 

 

 

 

 

 

14

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CLRCMOS1

 

 

 

 

 

 

15

23

 

 

1

 

 

 

 

 

 

 

 

 

 

 

ATX12V1

 

 

 

 

 

 

REAR Center: SPK

 

 

HDMI_SPDIF1

 

 

RoHS 64Mb

 

 

 

 

 

1

 

 

 

AMD

 

 

SPDIF Optical Bottom:

CTRB ASS

Top:

 

 

 

USB3_0_1

BIOS

 

 

AUDIO

 

 

 

A75 FCH

 

 

CODEC

 

 

Front USB 3.0

 

 

MI Bottom: CI N

FRON Center: T

LINE Top: IN

 

 

 

(Hudson-D3)

 

 

HD_AUDIO1

 

FM2A75M-ITX

 

Chipset

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

PCIE1

 

 

 

 

 

 

 

22

21

20

19

18

17

16

 

 

1

CPU Fan Connector (CPU_FAN1)

13

SATA3 Connector (SATA3_4)

2

CPU Fan Connector (CPU_FAN2)

14

SATA3 Connector (SATA3_1)

3

ATX Power Connector (ATXPWR1)

15

SATA3 Connector (SATA3_2)

4

Chassis Speaker Header (SPEAKER1)

16

Southbridge Controller

5

2 x 240-pin DDR3 DIMM Slots

17

SPI Flash Memory (64Mb)

 

(Dual Channel: DDR3_A1, DDR3_B1)

18

PCI Express 2.0 x16 Slot (PCIE1)

6

Chassis Fan Connector (CHA_FAN1)

19

USB 3.0 Header (USB3_0_1)

7

CPU Socket

20

ATX 12V Power Connector (ATX12V1)

8

System Panel Header (PANEL1)

21

Front Panel Audio Header (HD_AUDIO1)

9

USB 2.0 Header (USB_45)

22

HDMI_SPDIF Header (HDMI_SPDIF1)

10

USB 2.0 Header (USB_67)

23

Clear CMOS Jumper (CLRCMOS1)

11

Consumer Infrared Module Header (CIR1)

24

CPU Heatsink Retention Module

12

SATA3 Connector (SATA3_3)

25

Chassis Intrusion Header (CI1)

2

ASRock FM2A75M-ITX Motherboard

I/O Panel

 

1

2

3

 

 

 

4

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

5

 

 

 

8

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

6

 

 

9

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

7

 

 

10

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

14

 

 

13

 

 

12

11

 

 

 

 

 

 

 

 

 

* 1

USB 2.0 Ports (USB01)

 

 

 

 

 

8

 

Line In (Light Blue)

 

 

* 2

USB 2.0 Ports (USB23)

 

 

 

 

 

*** 9

 

Front Speaker (Lime)

 

 

** 3

LAN RJ-45 Port

 

 

 

 

 

10

 

Microphone (Pink)

 

 

4

D-Sub Port (VGA1)

 

 

 

 

 

11

 

HDMI Port (HDMI1)

 

 

5

Central / Bass (Orange)

 

 

 

 

 

12

 

USB 3.0 Ports (USB3_23)

 

 

6

Rear Speaker (Black)

 

 

 

 

 

**** 13

 

eSATA3 Connector (eSATA3_1)

7

Optical SPDIF Out Port

 

 

 

 

 

14

 

PS/2 Keyboard Port (Purple)

*It is recommended to install the USB Keyboard/Mouse cable to USB 2.0 ports (USB01 or USB23) instead of USB 3.0 ports.

**There are two LED next to the LAN port. Please refer to the table below for the LAN port LED indications.

 

LAN Port LED Indications

 

ACT/LINK

SPEED

 

Activity/Link LED

 

 

SPEED LED

 

 

 

 

 

 

LED

LED

 

Status

Description

 

Status

 

Description

 

 

 

 

 

 

 

 

 

 

 

 

Off

No Link

 

Off

 

10Mbps connection

 

 

 

 

 

 

Blinking

Data Activity

 

Orange

 

100Mbps connection

 

 

 

 

 

 

On

Link

 

Green

 

1Gbps connection

 

 

LAN Port

 

 

 

 

 

 

 

 

 

 

 

 

*** If you use 2-channel speaker, please connect the speaker’s plug into “Front Speaker Jack”.

 

See the table below for connection details in accordance with the type of speaker you use.

 

 

 

TABLE for Audio Output Connection

 

 

 

 

English

 

 

 

 

 

 

 

 

 

 

 

(No. 8)

 

Audio Output Channels

Front Speaker

Rear Speaker

Central / Bass

 

Line In or

 

 

 

 

 

(No. 9)

 

(No. 6)

(No. 5)

 

Side Speaker

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2

 

 

V

--

--

 

 

 

--

 

 

 

4

 

 

V

 

V

--

 

 

 

--

 

 

 

6

 

 

V

 

V

V

 

 

--

 

 

 

8

 

 

V

 

V

V

 

 

V

 

 

3

ASRock FM2A75M-ITX Motherboard

To enable Multi-Streaming function, you need to connect a front panel audio cable to the front panel audio header. After restarting your computer, you will find “Mixer” tool on your system. Please select “Mixer ToolBox” , click “Enable playback multi-streaming”, and click “ok”.

Choose “2CH”, “4CH”, “6CH”, or “8CH” and then you are allowed to select “Realtek HDA Primary output” to use Rear Speaker, Central/Bass, and Front Speaker, or select “Realtek HDA Audio 2nd output” to use front panel audio.

**** eSATA3 connector supports SATA Gen3 in cable 1M.

English

4

ASRock FM2A75M-ITX Motherboard

1. Introduction

Thank you for purchasing ASRock FM2A75M-ITX motherboard, a reliable motherboard produced under ASRock’s consistently stringent quality control. It delivers excellent performance with robust design conforming to ASRock’s commitment to quality and endurance.

This Quick Installation Guide contains introduction of the motherboard and step-by- step installation guide. More detailed information of the motherboard can be found in the user manual presented in the Support CD.

Because the motherboard specifications and the BIOS software might be updated, the content of this manual will be subject to change without notice. In case any modifications of this manual occur, the updated version will be available on ASRock website without further notice. You may find the latest VGA cards and CPU support lists on ASRock website as well. ASRock website http://www.asrock.com

If you require technical support related to this motherboard, please visit our website for specific information about the model you are using. www.asrock.com/support/index.asp

1.1 Package Contents

ASRock FM2A75M-ITX Motherboard (Mini-ITX Form Factor)

ASRock FM2A75M-ITX Quick Installation Guide

ASRock FM2A75M-ITX Support CD

2 x Serial ATA (SATA) Data Cables (Optional)

1 x I/O Panel Shield

ASRock Reminds You...

To get better performance in Windows® 8 / 8 64-bit / 7 / 7 64-bit / VistaTM / VistaTM 64-bit, it is recommended to set the BIOS option in Storage Configuration to AHCI mode. For the BIOS setup, please refer to the “User Manual” in our support CD for details.

English

5

ASRock FM2A75M-ITX Motherboard

English

1.2 Specifications

Platform

- Mini-ITX Form Factor

 

- All Solid Capacitor design

CPU

- Support for Socket FM2 100W processors

 

- Supports AMD’s Cool ‘n’ QuietTM Technology

 

- UMI-Link GEN2

Chipset

- AMD A75 FCH (Hudson-D3)

Memory

- Dual Channel DDR3 Memory Technology

 

- 2 x DDR3 DIMM slots

 

- Support DDR3 2600+(OC)/2400(OC)/2133(OC)/1866/1600/

 

1333/1066/800 non-ECC, un-buffered memory

 

(see CAUTION 1)

 

- Max. capacity of system memory: 32GB (see CAUTION 2)

 

- Supports Intel® Extreme Memory Profile (XMP) 1.3 / 1.2

 

- Supports AMD Memory Profile (AMP)

Expansion Slot

- 1 x PCI Express 2.0 x16 slot

 

- Supports AMD Dual Graphics

Graphics

- AMD Radeon HD 7000 graphics

 

- DirectX 11, Pixel Shader 5.0

 

- Max. shared memory 2GB

 

- Dual VGA Output: support HDMI and D-Sub ports by

 

independent display controllers

 

- Supports HDMI 1.4a Technology with max. resolution up to

 

1920x1200 @ 60Hz

 

- Supports D-Sub with max. resolution up to 1920x1600 @

 

60Hz

 

- Supports Auto Lip Sync, Deep Color (12bpc), xvYCC and

 

HBR (High Bit Rate Audio) with HDMI (Compliant HDMI

 

monitor is required) (see CAUTION 3)

 

- Supports Blu-ray Stereoscopic 3D with HDMI 1.4a

 

- Supports AMD Steady VideoTM 2.0: New video post

 

processing capability for automatic jutter reduction on home/

 

online video

 

- Supports HDCP function with HDMI port

 

- Supports Full HD 1080p Blu-ray (BD) / HD-DVD playback

 

with HDMI port

Audio

- 7.1 CH HD Audio with Content Protection

 

(Realtek ALC892 Audio Codec)

 

- Premium Blu-ray audio support

 

- Supports THX TruStudioTM

6

ASRock FM2A75M-ITX Motherboard

 

 

LAN

- PCIE x1 Gigabit LAN 10/100/1000 Mb/s

 

- Realtek RTL8111E

 

- Supports Wake-On-LAN

 

- Supports LAN Cable Detection

 

- Supports Energy Efficient Ethernet 802.3az

 

- Supports PXE

 

 

Rear Panel I/O

I/O Panel

 

- 1 x PS/2 Keyboard Port

 

- 1 x D-Sub Port

 

- 1 x HDMI Port

 

- 1 x Optical SPDIF Out Port

 

- 4 x Ready-to-Use USB 2.0 Ports

 

- 1 x eSATA3 Connector

 

- 2 x Ready-to-Use USB 3.0 Ports

 

- 1 x RJ-45 LAN Port with LED (ACT/LINK LED and SPEED

 

LED)

 

- HD Audio Jack: Rear Speaker/Central/Bass/Line in/Front

 

Speaker/Microphone

 

 

SATA3

- 4 x SATA3 6.0 Gb/s connectors, support RAID (RAID 0,

 

RAID 1 and RAID 10), NCQ, AHCI and “Hot Plug” functions

USB 3.0

- 2 x Rear USB 3.0 ports, support USB 1.1/2.0/3.0 up to

 

5Gb/s

 

- 1 x Front USB 3.0 header (supports 2 USB 3.0 ports),

 

supports USB 1.1/2.0/3.0 up to 5Gb/s

Connector

- 4 x SATA3 6.0Gb/s connectors

 

- 1 x CIR header

 

- 1 x HDMI_SPDIF header

 

- 1 x Chassis Intrusion header

 

- 2 x CPU Fan connectors (1 x 4-pin, 1 x 3-pin)

 

- 1 x Chassis Fan connector (4-pin)

 

- 24 pin ATX power connector

 

- 4 pin 12V power connector

 

- Front panel audio connector

 

- 2 x USB 2.0 headers (support 4 USB 2.0 ports)

 

- 1 x USB 3.0 header (supports 2 USB 3.0 ports)

BIOS Feature

- 64Mb AMI UEFI Legal BIOS with GUI support

 

- Supports “Plug and Play”

 

- ACPI 1.1 Compliance Wake Up Events

 

- Supports jumperfree

 

- SMBIOS 2.3.1 Support

 

- DRAM, APU PCIE VDDP, SB, CPU and CPU NB/GFX

 

Voltage Multi-adjustment

7

English

ASRock FM2A75M-ITX Motherboard

 

 

Support CD

- Drivers, Utilities, AntiVirus Software (Trial Version),

 

CyberLink MediaEspresso 6.5 Trial, Google Chrome

 

Browser and Toolbar

Hardware

- CPU Temperature Sensing

Monitor

- Chassis Temperature Sensing

 

- CPU Fan Tachometer

 

- Chassis Fan Tachometer

 

- CPU Quiet Fan

 

- CPU/Chassis Fan Multi-Speed Control

 

- CASE OPEN detection

 

- Voltage Monitoring: +12V, +5V, +3.3V, Vcore

OS

- Microsoft® Windows® 8 / 8 64-bit / 7 / 7 64-bit / VistaTM /

 

VistaTM 64-bit compliant

Certifications

- FCC, CE, WHQL

-ErP/EuP Ready (ErP/EuP ready power supply is required)

* For detailed product information, please visit our website: http://www.asrock.com

WARNING

Please realize that there is a certain risk involved with overclocking, including adjusting the setting in the BIOS, applying Untied Overclocking Technology, or using third-party overclocking tools. Overclocking may affect your system’s stability, or even cause damage to the components and devices of your system. It should be done at your own risk and expense. We are not responsible for possible damage caused by overclocking.

English

8

ASRock FM2A75M-ITX Motherboard

CAUTION!

1.Whether 2600/2400/2133/1866/1600MHz memory speed is supported depends on the CPU you adopt. If you want to adopt DDR3 2600/2400/2133/1866/1600 memory module on this motherboard, please refer to the memory support list on our website for the compatible memory modules.

ASRock website http://www.asrock.com

2.Due to the operating system limitation, the actual memory size may be less than 4GB for the reservation for system usage under Windows® 8 / 7 / VistaTM. For Windows® 64-bit OS with 64bit CPU, there is no such limitation. You can use ASRock XFast RAM to utilize the memory that Windows® cannot use.

3.xvYCC and Deep Color are only supported under Windows® 8 64-bit / 8 / 7 64-bit / 7. Deep Color mode will be enabled only if the display supports 12bpc in EDID. HBR is supported under Windows® 8 64-bit / 8 / 7 64-bit / 7 / VistaTM 64-bit / VistaTM.

English

9

ASRock FM2A75M-ITX Motherboard

English

1.3 Unique Features

ASRock Extreme Tuning Utility (AXTU)

ASRock Extreme Tuning Utility (AXTU) is an all-in-one tool to ne-tune different system functions in a user-friendly interface, which includes Hardware Monitor, Fan Control, Overclocking, OC DNA, IES and XFast RAM. In Hardware Monitor, it shows the major readings of your system. In Fan Control, it shows the fan speed and temperature for you to adjust. In Overclocking, you are allowed to overclock CPU frequency for optimal system performance. In OC DNA, you can save your OC settings as a profile and share it with your friends. Your friends then can load the OC profile to their own system to get the same OC settings. In IES (Intelligent Energy Saver), the voltage regulator can reduce the number of output phases to improve efficiency when the CPU cores are idle without sacrificing computing performance. In XFast RAM, it fully utilizes the memory space that cannot be used under Windows® OS 32-bit CPU.

ASRock Instant Boot

ASRock Instant Boot allows you to turn on your PC in just a few seconds, provides a much more efficient way to save energy, time, money, and improves system running speed for your system. It leverages the S3 and S4 ACPI features which normally enable the Sleep/Standby and Hibernation modes in Windows® to shorten boot up time. By calling S3 and S4 at specific timing during the shutdown and startup process, Instant Boot allows you to enter your Windows® desktop in a few seconds.

ASRock Instant Flash

ASRock Instant Flash is a BIOS flash utility embedded in Flash ROM. This convenient BIOS update tool allows you to update system BIOS without entering operating systems first like MS-

DOS or Windows®. With this utility, you can press the <F6> key during the POST or the <F2> key to enter into the BIOS setup menu to access ASRock Instant Flash. Just launch this tool and save the new BIOS file to your USB flash drive, floppy disk or hard drive, then you can update your BIOS only in a few clicks without preparing an additional floppy diskette or other complicated flash utility. Please be noted that the USB flash drive or hard drive must use FAT32/16/12 file system.

10

ASRock FM2A75M-ITX Motherboard

ASRock APP Charger

If you desire a faster, less restricted way of charging your Apple devices, such as iPhone/iPad/iPod Touch, ASRock has prepared a wonderful solution for you - ASRock APP Charger. Simply install the APP Charger driver, it makes your iPhone charge much quickly from your computer and up to 40% faster than before. ASRock APP Charger allows you to quickly charge many Apple devices simultaneously and even supports continuous charging when your PC enters into Standby mode (S1), Suspend to RAM (S3), hibernation mode (S4) or power off (S5). With APP Charger driver installed, you can easily enjoy the marvelous charging experience.

ASRock XFast USB

ASRock XFast USB can boost USB storage device performance. The performance may depend on the properties of the device.

ASRock XFast LAN

ASRock XFast LAN provides a faster internet access, which includes the benefits listed below. LAN Application Prioritization: You can configure your application’s priority ideally and/or add new programs. Lower Latency in Game: After setting online game’s priority higher, it can lower the latency in games. Traffic Shaping: You can watch Youtube HD videos and download simultaneously. Real-Time Analysis of Your Data: With the status window, you can easily recognize which data streams you are transferring currently.

ASRock XFast RAM

ASRock XFast RAM is a new function that is included into ASRock Extreme Tuning Utility (AXTU). It fully utilizes the memory space that cannot be used under Windows® OS 32-bit CPU. ASRock XFast RAM shortens the loading time of previously visited websites, making web surfing faster than ever. And it also boosts the speed of Adobe Photoshop 5 times faster. Another advantage of ASRock XFast RAM is that it reduces the frequency of accessing your SSDs or HDDs in order to extend their lifespan.

English

11

ASRock FM2A75M-ITX Motherboard

English

12

ASRock Crashless BIOS

ASRock Crashless BIOS allows users to update their BIOS without fear of failing. If power loss occurs during the BIOS update process, ASRock Crashless BIOS will automatically finish the BIOS update procedure after regaining power. Please note that BIOS files need to be placed in the root directory of your USB disk. Only USB2.0 ports support this feature.

ASRock OMG (Online Management Guard)

Administrators are able to establish an internet curfew or restrict internet access at specified times via OMG. You may schedule the starting and ending hours of internet access granted to other users. In order to prevent users from bypassing OMG, guest accounts without permission to modify the system time are required.

ASRock Internet Flash

ASRock Internet Flash searches for available UEFI firmware updates from our servers. In other words, the system can autodetect the latest UEFI from our servers and flash them without entering Windows® OS. Please note that you must be running on a DHCP configured computer in order to enable this function.

ASRock UEFI System Browser

ASRock UEFI system browser is a useful tool included in graphical UEFI. It can detect the devices and configurations that users are currently using in their PC. With the UEFI system browser, you can easily examine the current system configuration in UEFI setup.

ASRock On/Off Play Technology

ASRock On/Off Play Technology allows users to enjoy the great audio experience from the portable audio devices, such like MP3 player or mobile phone to your PC, even when the PC is turned off (or in ACPI S5 mode)! This motherboard also provides a free 3.5mm audio cable (optional) that ensures users the most convenient computing environment.

ASRock FM2A75M-ITX Motherboard

ASRock Dehumidifier Function

Users may prevent motherboard damages due to dampness by enabling “Dehumidifier Function”. When enabling Dehumidifier Function, the computer will power on automatically to dehumidify the system after entering S4/S5 state.

ASRock Easy RAID Installer

ASRock Easy RAID Installer can help you to copy the RAID driver from a support CD to your USB storage device. After copying the RAID driver to your USB storage device, please change “SATA Mode” to “RAID”, then you can start installing the OS in RAID mode.

ASRock Interactive UEFI

ASRock Interactive UEFI is a blend of system configuration tools, cool sound effects and stunning visuals. The unprecedented UEFI provides a more attractive interface and brings a lot more amusement.

ASRock Fast Boot

With ASRock’s exclusive Fast Boot technology, it takes less than 1.5 seconds to logon to Windows® 8 from a cold boot. No more waiting! The speedy boot will completely change your user experience and behavior.

ASRock X-Boost

Brilliantly designed for combo overclocking, ASRock X-Boost Technology is able to unleash the hidden power of your CPUs. Simply press “X” when turning on the PC, X-Boost will automatically overclock the relative components to get up to 15.77% performance boost! With the smart X-Boost, overclocking CPU can become a near one-button process.

ASRock Restart to UEFI

Windows® 8 brings the ultimate boot up experience. The lightning boot up speed makes it hard to access the UEFI setup. ASRock Restart to UEFI technology is designed for those requiring frequent UEFI access. It is included in ASRock’s exclusive all- in-one AXTU tuning program that allows users to easily enter the UEFI automatically when turning on the PC next time. Just simply enable this function; the PC will be assured to access the UEFI directly in the very beginning.

English

13

ASRock FM2A75M-ITX Motherboard

2. Installation

This is a Mini-ITX form factor motherboard. Before you install the motherboard, study the configuration of your chassis to ensure that the motherboard fits into it.

Pre-installation Precautions

Take note of the following precautions before you install motherboard components or change any motherboard settings.

Before you install or remove any component, ensure that the power is switched off or the power cord is detached from the power supply. Failure to do so may cause severe damage to the motherboard, peripherals, and/or components.

1.Unplug the power cord from the wall socket before touching any component.

2.To avoid damaging the motherboard components due to static electricity, NEVER place your motherboard directly on the carpet or the like. Also remember to use a grounded wrist strap or touch a safety grounded object before you handle components.

3.Hold components by the edges and do not touch the ICs.

4.Whenever you uninstall any component, place it on a grounded antistatic pad or in the bag that comes with the component.

5.When placing screws into the screw holes to secure the motherboard to the chassis, please do not over-tighten the screws! Doing so may damage the motherboard.

English

14

ASRock FM2A75M-ITX Motherboard

2.1 CPU Installation

Step 1. Unlock the socket by lifting the lever up to a 90o angle.

Step 2. Position the CPU directly above the socket such that the CPU corner with the golden triangle matches the socket corner with a small triangle.

Step 3. Carefully insert the CPU into the socket until it fits in place.

The CPU fits only in one correct orientation. DO NOT force the CPU into the socket to avoid bending of the pins.

Step 4. When the CPU is in place, press it firmly on the socket while you push down the socket lever to secure the CPU. The lever clicks on the side tab to indicate that it is locked.

Lever 90° Up

 

 

 

CPU Golden Triangle

 

 

Socket Corner Small

 

 

Triangle

 

STEP 1:

STEP 2 / STEP 3:

STEP 4:

Lift Up The Socket Lever

Match The CPU Golden Triangle

Push Down And Lock

 

To The Socket Corner Small

The Socket Lever

 

Triangle

 

2.2 Installation of CPU Fan and Heatsink

After you install the CPU into this motherboard, it is necessary to install a larger heatsink and cooling fan to dissipate heat. You also need to spray thermal grease between the CPU and the heatsink to improve heat dissipation. Make sure that the CPU and the heatsink are securely fastened and in good contact with each other. Then connect the CPU fan to the CPU FAN connector (CPU_FAN1, see Page 2, No. 1 or CPU_FAN2, see Page 2, No. 2). For proper installation, please kindly refer to the instruction manuals of the CPU fan and the heatsink.

English

15

ASRock FM2A75M-ITX Motherboard

2.3 Installation of Memory Modules (DIMM)

This motherboard provides two 240-pin DDR3 (Double Data Rate 3) DIMM slots, and supports Dual Channel Memory Technology. For dual channel configuration, you always need to install two identical (the same brand, speed, size and chiptype) memory modules in the DDR3 DIMM slots to activate Dual Channel Memory Technology. Otherwise, it will operate at single channel mode.

1.It is not allowed to install a DDR or DDR2 memory module into DDR3 slot;otherwise, this motherboard and DIMM may be damaged.

2.If you install only one memory module or two non-identical memory modules, it is unable to activate the Dual Channel Memory Technology.

Installing a DIMM

Please make sure to disconnect power supply before adding or removing DIMMs or the system components.

Step 1. Unlock a DIMM slot by pressing the retaining clips outward.

Step 2. Align a DIMM on the slot such that the notch on the DIMM matches the break on the slot.

English

notch break

notch

break

The DIMM only fits in one correct orientation. It will cause permanent damage to the motherboard and the DIMM if you force the DIMM into the slot at incorrect orientation.

Step 3. Firmly insert the DIMM into the slot until the retaining clips at both ends fully snap back in place and the DIMM is properly seated.

16

ASRock FM2A75M-ITX Motherboard

2.4 Expansion Slot (PCI Express Slot)

There is 1 PCI Express slot on this motherboard.

PCIE Slot: PCIE1 (PCIE x16 slot) is used for PCI Express x16 lane width graphics cards.

Installing an expansion card

Step 1. Before installing the expansion card, please make sure that the power supply is switched off or the power cord is unplugged. Please read the documentation of the expansion card and make necessary hardware settings for the card before you start the installation.

Step 2. Remove the system unit cover (if your motherboard is already installed in a chassis).

Step 3. Remove the bracket facing the slot that you intend to use. Keep the screws for later use.

Step 4. Align the card connector with the slot and press firmly until the card is completely seated on the slot.

Step 5. Fasten the card to the chassis with screws. Step 6. Replace the system cover.

English

17

ASRock FM2A75M-ITX Motherboard

2.5 Jumpers Setup

The illustration shows how jumpers are setup. When the jumper cap is placed on pins, the jumper is “Short”. If no jumper cap is placed on pins, the jumper is “Open”. The illustration shows a 3-pin jumper whose pin1 and pin2 are “Short” when jumper cap is placed on these 2 pins.

Jumper

Setting

Description

Clear CMOS Jumper

 

 

(CLRCMOS1)

 

 

(see p.2, No. 23)

Default

Clear CMOS

 

Note: CLRCMOS1 allows you to clear the data in CMOS. To clear and reset the system parameters to default setup, please turn off the computer and unplug the power cord from the power supply. After waiting for 15 seconds, use a jumper cap to short pin2 and pin3 on CLRCMOS1 for 5 seconds. However, please do not clear the CMOS right after you update the BIOS. If you need to clear the CMOS when you just finish updating the BIOS, you must boot up the system first, and then shut it down before you do the clear-CMOS action. Please be noted that the password, date, time, user default profile, 1394 GUID and MAC address will be cleared only if the CMOS battery is removed.

If you clear the CMOS, the case open may be detected. Please adjust the BIOS option “Clear Status” to clear the record of previous chassis intrusion status.

English

18

ASRock FM2A75M-ITX Motherboard

2.6 Onboard Headers and Connectors

Onboard headers and connectors are NOT jumpers. Do NOT place jumper caps over these headers and connectors. Placing jumper caps over the headers and connectors will cause permanent damage of the motherboard!

Serial ATA3 Connectors

(SATA3_1: see p.2, No. 14) (SATA3_2: see p.2, No. 15) (SATA3_3: see p.2, No. 12) (SATA3_4: see p.2, No. 13)

Serial ATA (SATA) Data Cable

(Optional)

USB 2.0 Headers

(9-pin USB_45)

(see p.2 No. 9)

(9-pin USB_67)

(see p.2 No. 10)

SATA3 4

SATA3 3

SATA3 2

SATA3 1

These four Serial ATA3 (SATA3) connectors support SATA data cables for internal storage devices. The current SATA3 interface allows up to 6.0 Gb/s data transfer rate.

Either end of the SATA data cable can be connected to the SATA3 hard disk or the SATA3 connector on this motherboard.

Besides four default USB 2.0 ports on the I/O panel, there are two USB 2.0 headers on this motherboard. Each USB 2.0 header can support two USB 2.0 ports.

USB 3.0 Header

 

IntA_P_D+

(19-pin USB3_0_1)

 

 

IntA_P_D-

 

 

 

 

 

GND

 

 

 

 

 

 

 

 

IntA_P_SSTX+

(see p.2, No. 19)

 

 

 

 

 

 

 

 

 

 

GND

 

 

 

 

 

 

 

 

 

IntA_P_SSTX-

 

 

 

 

 

 

 

 

 

 

 

 

 

IntA_P_SSRX+

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

IntA_P_SSRX-

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Vbus

 

1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Vbus

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

IntA_P_SSRX-

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

IntA_P_SSRX+

 

 

 

 

 

 

 

 

 

 

 

 

 

 

GND

 

 

 

 

 

 

 

 

 

 

 

IntA_P_SSTX-

 

 

 

 

 

 

 

 

 

IntA_P_SSTX+

 

 

 

 

 

 

 

 

GND

 

 

 

 

 

 

IntA_P_D-

 

 

 

IntA_P_D+

 

 

 

 

 

ID

Besides two default USB 3.0 ports on the I/O panel, there is one USB 3.0 header on this motherboard. This USB 3.0 header can support two USB 3.0 ports.

19

English

ASRock FM2A75M-ITX Motherboard

Consumer Infrared Module Header

This header can be used to

(4-pin CIR1)

connect the remote

(see p.2 No. 11)

controller receiver.

Front Panel Audio Header

 

 

GND

(9-pin HD_AUDIO1)

 

 

 

 

PRESENCE#

 

 

 

 

 

 

MIC_RET

 

 

 

 

 

 

 

 

 

 

 

OUT_RET

(see p.2 No. 21)

1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

OUT2_L

 

 

 

 

 

 

 

 

J_SENSE

 

 

 

 

 

 

 

OUT2_R

 

 

 

 

 

MIC2_R

 

 

 

MIC2_L

This is an interface for the front panel audio cable that allows convenient connection and control of audio devices.

1.High Definition Audio supports Jack Sensing, but the panel wire on the chassis must support HDA to function correctly. Please follow the instruction in our manual and chassis manual to install your system.

2.If you use AC’97 audio panel, please install it to the front panel audio header as below:

A.Connect Mic_IN (MIC) to MIC2_L.

B.Connect Audio_R (RIN) to OUT2_R and Audio_L (LIN) to OUT2_L.

C.Connect Ground (GND) to Ground (GND).

D.MIC_RET and OUT_RET are for HD audio panel only. You don’t need to connect them for AC’97 audio panel.

E.To activate the front mic.

For Windows® 8 / 8 64-bit / 7 / 7 64-bit / VistaTM / VistaTM 64-bit OS: Go to the “FrontMic” Tab in the Realtek Control panel. Adjust “Recording Volume”.

System Panel Header

This header accommodates

(9-pin PANEL1)

several system front panel

(see p.2 No. 8)

functions.

English

20

Connect the power switch, reset switch and system status indicator on the chassis to this header according to the pin assignments below. Note the positive and negative pins before connecting the cables.

PWRBTN (Power Switch):

Connect to the power switch on the chassis front panel. You may configure the way to turn off your system using the power switch.

RESET (Reset Switch):

Connect to the reset switch on the chassis front panel. Press the reset switch to restart the computer if the computer freezes and fails to perform a normal restart.

ASRock FM2A75M-ITX Motherboard

PLED (System Power LED):

Connect to the power status indicator on the chassis front panel. The LED is on when the system is operating. The LED keeps blinking when the sys-tem is in S1 sleep state. The LED is off when the system is in S3/S4 sleep state or powered off (S5).

HDLED (Hard Drive Activity LED):

Connect to the hard drive activity LED on the chassis front panel. The LED is on when the hard drive is reading or writing data.

The front panel design may differ by chassis. A front panel module mainly consists of power switch, reset switch, power LED, hard drive activity LED, speaker and etc. When connecting your chassis front panel module to this header, make sure the wire assignments and the pin assign-ments are matched correctly.

Chassis Speaker Header

 

 

 

 

 

Please connect the chassis

(4-pin SPEAKER 1)

 

 

 

 

 

speaker to this header.

(see p.2

No. 4)

 

 

 

 

 

 

 

 

 

 

 

 

 

Chassis Fan Connector

 

 

 

 

 

Please connect the fan cable

(4-pin CHA_FAN1)

 

GND

 

 

to the fan connector and

(see p.2

No. 6)

 

+12V

 

 

match the black wire to the

 

CHA_FAN_SPEED

 

 

 

FAN_SPEED_CONTROL

ground pin.

 

 

 

 

 

 

 

 

 

 

 

CPU Fan Connectors

 

FAN_SPEED_CONTROL

Please connect the CPU fan

(4-pin CPU_FAN1)

CPU_FAN_SPEED

cable to the connector and

(see p.2

No. 1)

 

+12V

 

match the black wire to the

 

GND

 

 

 

 

 

1

2

3

4

ground pin.

 

 

 

Though this motherboard provides 4-Pin CPU fan (Quiet Fan) support, the 3-Pin CPU fan still can work successfully even without the fan speed control function. If you plan to connect the 3-Pin CPU fan to the CPU fan connector on this motherboard, please connect it to Pin 1-3.

Pin 1-3 Connected

3-Pin Fan Installation

(3-pin CPU_FAN2)

GND

(see p.2 No. 2)

+12V

CPU_FAN_SPEED

 

 

 

 

 

 

21

English

ASRock FM2A75M-ITX Motherboard

ATX Power Connector

(24-pin ATXPWR1)

24

13

 

 

(see p.2 No. 3)

12

1

Please connect an ATX power supply to this connector.

Though this motherboard provides 24-pin ATX power connector, it can still work if you adopt a traditional 20-pin ATX power supply. To use the 20-pin ATX power supply, please plug your power supply along with Pin 1 and Pin 13.

24

13

 

 

 

 

 

 

20-Pin ATX Power Supply Installation

 

 

12

1

ATX 12V Power Connector

Please connect an ATX 12V

(4-pin ATX12V1)

power supply to this connector.

(see p.2, No. 20)

 

HDMI_SPDIF Header

(2-pin HDMI_SPDIF1)

(see p.2 No. 22)

1

GND

SPDIFOUT

HDMI_SPDIF header, providing SPDIF audio output to HDMI VGA card, allows the system to connect HDMI Digital TV/ projector/LCD devices. Please connect the HDMI_SPDIF connector of HDMI VGA card to this header.

Chassis Intrusion Header

(2-pin CI1)

1

 

 

 

 

 

 

(see p.2, No. 25)

 

 

GND

Signal

English

This motherboard supports CASE OPEN detection feature that detects if the chassis cover has been removed. This feature requires a chassis with chassis intrusion detection design.

22

ASRock FM2A75M-ITX Motherboard

2.7Driver Installation Guide

To install the drivers to your system, please insert the support CD to your optical drive first. Then, the drivers compatible to your system can be auto-detected and listed on the support CD driver page. Please follow the order from up to bottom side to install those required drivers. Therefore, the drivers you install can work properly.

2.8Installing Windows® 8 / 8 64-bit / 7 / 7 64-bit / VistaTM /

VistaTM 64-bit With RAID Functions

If you want to install Windows® 8 / 8 64-bit / 7 / 7 64-bit / VistaTM / VistaTM 64-bit on a RAID disk composed of 2 or more SATA3 HDDs with RAID functions, please follow below steps.

STEP 1: Set up UEFI.

A.Enter UEFI SETUP UTILITYAdvanced screen Storage Configuration.

B.Set the “SATA Mode” option to [RAID].

STEP 2: Use “RAID Installation Guide” to set RAID configuration.

Before you start to configure RAID function, you need to check the RAID installation guide in the Support CD for proper configuration. Please refer to the BIOS RAID installation guide part of the document in the following path in the Support CD:

.. \ RAID Installation Guide

STEP 3: Install Windows® 8 / 8 64-bit / 7 / 7 64-bit / VistaTM / VistaTM 64-bit OS on your system.

Use the option “Easy RAID Installer“ in UEFI setup utility to copy the RAID drivers to your USB flash disk. Insert the Windows® OS optical disk into the optical drive to boot your system, and follow the instruction to install OS on your system. When you see “Where do you want to install Windows?” page, please insert your USB flash disk to your system, and click the “Load Driver” button to load the RAID drivers. After that, you can continue the OS installation.

2.9Installing Windows® 8 / 8 64-bit / 7 / 7 64-bit / VistaTM /

VistaTM 64-bit Without RAID Functions

If you want to install Windows® 8 / 8 64-bit / 7 / 7 64-bit / VistaTM / VistaTM 64-bit on your SATA3 HDDs without RAID functions, please follow below steps.

23

English

ASRock FM2A75M-ITX Motherboard

English

Using SATA3 HDDs without NCQ and Hot Plug functions (IDE mode)

STEP 1: Set up UEFI.

A.Enter UEFI SETUP UTILITY Advanced screen Storage Configuration.

B.Set the “SATA Mode” option to [IDE].

STEP 2: Install Windows® 8 / 8 64-bit / 7 / 7 64-bit / VistaTM / VistaTM 64-bit OS on your system.

Using SATA3 HDDs with NCQ and Hot Plug functions (AHCI mode)

STEP 1: Set up UEFI.

A.Enter UEFI SETUP UTILITYAdvanced screenStorage Configuration.

B.Set the “SATA Mode” option to [AHCI].

STEP 2: Install Windows® 8 / 8 64-bit / 7 / 7 64-bit / VistaTM / VistaTM 64-bit OS on your system.

3. BIOS Information

The Flash Memory on the motherboard stores BIOS Setup Utility. When you start up the computer, please press <F2> or <Del> during the Power-On-Self-Test (POST) to enter BIOS Setup utility; otherwise, POST continues with its test routines. If you wish to enter BIOS Setup after POST, please restart the system by pressing <Ctl> + <Alt> + <Delete>, or pressing the reset button on the system chassis. The BIOS Setup program is designed to be user-friendly. It is a menu-driven program, which allows you to scroll through its various sub-menus and to select among the predetermined choices. For the detailed information about BIOS Setup, please refer to the User Manual (PDF file) contained in the Support CD.

4. Software Support CD information

This motherboard supports various Microsoft® Windows® operating systems: 8 /

8 64-bit / 7 / 7 64-bit / VistaTM / VistaTM 64-bit. The Support CD that came with the motherboard contains necessary drivers and useful utilities that will enhance motherboard features. To begin using the Support CD, insert the CD into your CD-ROM drive. It will display the Main Menu automatically if “AUTORUN” is enabled in your computer. If the Main Menu does not appear automatically, locate and double-click on the file “ASSETUP.EXE” from the BIN folder in the Support CD to display the menus.

24

ASRock FM2A75M-ITX Motherboard

1. Einführung

Wir danken Ihnen für den Kauf des ASRock FM2A75M-ITX Motherboard, ein zuverlässiges Produkt, welches unter den ständigen, strengen Qualitätskontrollen von ASRock gefertigt wurde. Es bietet Ihnen exzellente Leistung und robustes Design, gemäß der Verpflichtung von ASRock zu Qualität und Halbarkeit. Diese Schnellinstallationsanleitung führt in das Motherboard und die schrittweise Installation ein. Details über das Motherboard finden Sie in der Bedienungsanleitung auf der Support-CD.

Da sich Motherboard-Spezifikationen und BIOS-Software verändern können, kann der Inhalt dieses Handbuches ebenfalls jederzeit geändert werden. Für den Fall, dass sich Änderungen an diesem Handbuch ergeben, wird eine neue Version auf der ASRock-Website, ohne weitere Ankündigung, verfügbar sein. Die neuesten Grafikkarten und unterstützten CPUs sind auch auf der ASRock-Website aufgelistet.

ASRock-Website: http://www.asrock.com

Wenn Sie technische Unterstützung zu Ihrem Motherboard oder spezifische Informationen zu Ihrem Modell benötigen, besuchen Sie bitte unsere Webseite:

www.asrock.com/support/index.asp

1.1 Kartoninhalt

ASRock FM2A75M-ITX Motherboard (Mini-ITX-Formfaktor)

ASRock FM2A75M-ITX Schnellinstallationsanleitung

ASRock FM2A75M-ITX Support-CD

Zwei Serial ATA (SATA) -Datenkabel (optional)

Ein I/O Shield

ASRock erinnert...

Zur besseren Leistung unter Windows® 8 / 8 64 Bit / 7 / 7 64 Bit / VistaTM /

VistaTM 64 Bit empfehlen wir, die Speicherkonfiguration im BIOS auf den

AHCI-Modus einzustellen. Hinweise zu den BIOS-Einstellungen finden

Sie in der Bedienungsanleitung auf der mitgelieferten CD.

Deutsch

25

ASRock FM2A75M-ITX Motherboard

Deutsch

1.2Spezifikationen

Plattform

- Mini-ITX-Formfaktor

 

- Alle Feste Kondensatordesign

CPU

- Unterstützt Sockel-FM2-100-W-Prozessoren

 

- Unterstützt Cool ‘n’ QuietTM-Technologie von AMD

 

- UMI-Link-GEN2

Chipsatz

- AMD A75 FCH (Hudson-D3)

Speicher

- Unterstützung von Dual-Kanal-Speichertechnologie

 

- 2 x Steckplätze für DDR3

 

- Unterstützt DDR3 2600+(OC)/2400(OC)/2133(OC)/1866/

 

1600/1333/1066/800 non-ECC, ungepufferter Speicher

 

- Max. Kapazität des Systemspeichers: 32GB

 

- Unterstützt Intel® Extreme Memory Profile (XMP)1.3/1.2

 

- Unterstützt AMD Memory Profile (AMP)

Erweiterungs-

- 1 x PCI-Express-2.0-x16-Steckplätze

steckplätze

- Unterstützt AMD duale Grafikkarten

Onboard-VGA

- AMD Radeon HD 7000-Grafik

 

- DirectX 11, Pixel Shader 5.0

 

- Maximal gemeinsam genutzter Speicher 2GB

 

- Doppel-VGAAusgabe: unterstützt HDMI und D-Sub Ports

 

durch unabhängige Bildschirmanzeige Kontrolleure

 

- Unterstützt HDMI 1.4a mit einer maximalen Auflösung von

 

1920 x 1200 bei 60 Hz

 

- Unterstützt D-Sub mit einer maximalen Auflösung von

 

1920 x 1600 bei 60 Hz

 

- Unterstützt Auto Lip Sync, Deep Color (12bpc), xvYCC und

 

HBR (High Bit Rate-Audio) mit HDMI (kompatibler HDMI-

 

Bildschirm erforderlich)

 

- Unterstützt stereoskopisches 3D per Blu-ray mit HDMI 1.4a

 

- Unterstützt AMD Steady VideoTM 2.0: Neuartige Funktion der

 

Videonachbearbeitung für automatische Reduzierung von

 

Bildschwankungen bei Heim-/Online-Videos

 

- Unterstützt HDCP-Funktion mit HDMI-Port

 

- Unterstutzt 1080p Blu-ray (BD) / HD-DVD-Wiedergabe

 

mit HDMI-Port

Audio

- 7.1CH HD Audio mit dem Inhalt Schutz

 

(Realtek ALC892 Audio Codec)

 

- Premium Blu-ray-Audio-Unterstützung

 

- Unterstützt THX TruStudioTM

LAN

- PCIE x1 Gigabit LAN 10/100/1000 Mb/s

26

ASRock FM2A75M-ITX Motherboard

 

 

 

- Realtek RTL8111E

 

- Unterstützt Wake-On-LAN

 

- Unterstützt LAN-Kabelerkennung

 

- Unterstützt energieeffizientes Ethernet 802.3az

 

- Unterstützt PXE

E/A-Anschlüsse

I/O Panel

an der

- 1 x PS/2-Tastaturanschluss

Rückseite

- 1 x D-Sub port

 

- 1 x HDMI port

 

- 1 x optischer SPDIF-Ausgang

 

- 4 x Standard-USB 2.0-Anschlüsse

 

- 1 x eSATA3-Anschluss

 

- 2 x Standard-USB 3.0-Anschlüsse

 

- 1 x RJ-45 LAN Port mit LED (ACT/LINK LED und SPEED

 

LED)

 

- HD Audiobuchse: Lautsprecher hinten / Mitte/Bass /

 

Audioeingang / Lautsprecher vorne / Mikrofon

SATA3

- 4 x SATA 3-Anschluss mit 6,0 Gb/s, unterstützt RAID-

 

(RAID 0, RAID 1 und RAID 10), NCQ-, AHCIund „Hot

 

Plugging“-Funktionen

USB3.0

- 2 x USB 3.0-Ports an der Rückseite, unterstützt USB

 

1.1/2.0/3.0 mit bis zu 5 Gb/s

 

- 1 x USB 3.0-Header (unterstützt zwei USB 3.0-Ports) an der

 

Vorderseite, unterstützt USB 1.1/2.0/3.0 mit bis zu 5 Gb/s

Anschlüsse

- 4 x SATA3 6,0 GB/s-Anschlüsse

 

- 1 x Consumer Infrarot-Modul-Header

 

- 1 x HDMI_SPDIF-Anschluss

 

- 1 x Verteiler für Gehäuseeindringversuche

 

- 2 x CPUlüfter-Anschluss (1 x 4-pin, 1 x 3-pin)

 

- 1 x Gehäuselüfter-Anschluss (4-pin)

 

- 24-pin ATX-Netz-Header

 

- 4-pin anschluss für 12V-ATX-Netzteil

 

- Anschluss für Audio auf der Gehäusevorderseite

 

- 2 x USB 2.0-Anschlüsse (Unterstützung 4 zusätzlicher

 

USB 2.0-Anschlüsse)

 

- 1 x USB 3.0-Anschlüsse (Unterstützung 2 zusätzlicher

 

USB 3.0-Anschlüsse)

BIOS

- 64Mb AMIs Legal BIOS UEFI mit GUI-Unterstützung

 

- Unterstützung für “Plug and Play”

 

- ACPI 1.1-Weckfunktionen

 

- JumperFree-Modus

 

- SMBIOS 2.3.1

27

Deutsch

ASRock FM2A75M-ITX Motherboard

 

- DRAM, APU PCIE VDDP, SB, CPU und CPU NB/GFX

 

Stromspannung Multianpassung

 

 

 

Support-CD

- Treiber, Dienstprogramme, Antivirussoftware

 

(Probeversion), CyberLink MediaEspresso 6.5-Testversion,

 

Google Chrome Browser und Toolbar

 

Hardware Monitor

- CPU-Temperatursensor

 

- Motherboardtemperaturerkennung

 

- Drehzahlmessung für CPUlüfter

 

- Drehzahlmessung für Gehäuselüfter

 

- Geräuscharmer CPUlüfter

 

- Mehrstufige Geschwindigkeitsteuerung für CPU-/

 

Gehäuselüfter

 

- GEHÄUSE OFFEN-Erkennung

 

- Spannungsüberwachung: +12V, +5V, +3.3V, Vcore

 

 

 

Betriebssysteme

- Unterstützt Microsoft® Windows® 8 / 8 64-Bit / 7 / 7 64-Bit /

 

VistaTM / VistaTM 64-Bit

Zertifizierungen

- FCC, CE, WHQL

-Gemäß Ökodesign-Richtlinie (ErP/EuP) (Stromversorgung gemäß Ökodesign-Richtlinie (ErP/EuP) erforderlich)

* Für die ausführliche Produktinformation, besuchen Sie bitte unsere Website: http://www.asrock.com

Deutsch

28

ASRock FM2A75M-ITX Motherboard

1.3 Einstellung der Jumper

Die Abbildung verdeutlicht, wie Jumper gesetzt werden. Werden Pins durch Jumperkappen verdeckt, ist der Jumper “Gebrückt”. Werden keine Pins durch Jumperkappen verdeckt, ist der Jumper “Offen”. Die Abbildung zeigt einen 3-Pin Jumper dessen Pin1 und Pin2 “Gebrückt” sind, bzw. es befindet sich eine Jumper-Kappe auf diesen beiden Pins.

Jumper

Einstellun

Beschreibung

CMOS löschen

 

 

(CLRCMOS1, 3-Pin jumper)

 

 

(siehe S.2, No. 23)

Default-

CMOS

 

Einstellung

löschen

Hinweis: CLRCMOS1 ermöglicht Ihnen die Löschung der Daten im CMOS. Zum Löschen und Zurücksetzen der Systemparameter auf die Standardeinrichtung schalten Sie den Computer bitte aus und trennen das Netzkabel von der Stromversorgung. Warten Sie 15 Sekunden, schließen Sie dann Pin2 und Pin3 am CLRCMOS1 über einen Jumper fünf Sekunden lang kurz. Sie sollten das CMOS allerdings nicht direkt nach der BIOS-Aktualisierung löschen. Wenn Sie das CMOS nach Abschluss der BIOS-Aktualisierung löschen müssen, fahren Sie zuerst das System hoch. Fahren Sie es dann vor der CMOS-Löschung herunter. Bitte beachten Sie, dass Kennwort, Datum, Uhrzeit, benutzerdefiniertes Profil, 1394 GUID und MAC-Adresse

nur gelöscht werden, wenn die CMOS-Batterie entfernt wird.

Durch Löschen des CMOS kann erkannt werden, wenn das Gehäuseoffen ist. Bitte stellen Sie zum Löschen der Aufzeichnung des vorherigenGehäuseindringungsstatus die BIOS-Option “Status leeren” ein.

Deutsch

29

ASRock FM2A75M-ITX Motherboard

1.4 Anschlüsse

Anschlussleisten sind KEINE Jumper. Setzen Sie KEINE Jumperkappen auf die Pins der Anschlussleisten. Wenn Sie die Jumperkappen auf die Anschlüsse setzen, wird das Motherboard permanent beschädigt!

Anschluss

Seriell-ATA3-Anschlüsse

(SATA3_1: siehe S.2 - No. 14) (SATA3_2: siehe S.2 - No. 15) (SATA3_3: siehe S.2 - No. 12) (SATA3_4: siehe S.2 - No. 13)

Beschreibung

SATA3 4

SATA3 3

SATA3 2

SATA3 1

Diese vier Serial ATA3- (SATA3-)Verbínder unterstützten SATA-Datenkabel für interne Massenspeichergeräte. Die aktuelle SATA3Schnittstelle ermöglicht eine Datenübertragungsrate bis 6,0 Gb/s.

Serial ATA- (SATA-)

SJedes Ende des SATA

Datenkabel

Datenkabels kann an die

(Option)

SATA3 Festplatte oder das

 

SATA3 Verbindungsstück auf

 

dieser Hauptplatine

 

angeschlossen werden.

 

 

USB 2.0-Header

Zusätzlich zu den vier

(9-pol. USB_45)

üblichen USB 2.0-Ports an den

(siehe S.2 - No. 9)

I/O-Anschlüssen befinden sich

 

zwei USB 2.0-

 

Anschlussleisten am

 

Motherboard. Pro USB 2.0-

(9-pol. USB_67)

Anschlussleiste werden zwei

(siehe S.2 - No. 10)

USB 2.0-Ports unterstützt.

Deutsch

30

ASRock FM2A75M-ITX Motherboard

Loading...
+ 116 hidden pages