ASRock B360 Pro4 Service Manual

Version 1.0

Published March 2018

Copyright©2018 ASRock INC. All rights reserved.

Copyright Notice:

No part of this documentation may be reproduced, transcribed, transmitted, or translated in any language, in any form or by any means, except duplication of documentation by the purchaser for backup purpose, without written consent of ASRock Inc.

Products and corporate names appearing in this documentation may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners’ benefit, without intent to

infringe.

Disclaimer:

Specifications and information contained in this documentation are furnished for informational use only and subject to change without notice, and should not be constructed as a commitment by ASRock. ASRock assumes no responsibility for any errors or omissions that may appear in this documentation.

With respect to the contents of this documentation, ASRock does not provide warranty of any kind, either expressed or implied, including but not limited to the implied warranties or conditions of merchantability or fitness for a particular purpose.

In no event shall ASRock, its directors, officers, employees, or agents be liable for any indirect, special, incidental, or consequential damages (including damages for loss of profits, loss of business, loss of data, interruption of business and the like), even if ASRock has been advised of the possibility of such damages arising from any defect or error in the documentation or product.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1)this device may not cause harmful interference, and

(2)this device must accept any interference received, including interference that may cause undesired operation.

CALIFORNIA, USA ONLY

The Lithium battery adopted on this motherboard contains Perchlorate, a toxic substance controlled in Perchlorate Best Management Practices (BMP) regulations passed by the California Legislature. When you discard the Lithium battery in California, USA, please follow the related regulations in advance.

“Perchlorate Material-special handling may apply, see www.dtsc.ca.gov/hazardouswaste/ perchlorate”

ASRock Website: http://www.asrock.com

AUSTRALIA ONLY

Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage caused by our goods. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. If you require assistance please call ASRock Tel

: [phone] ext.123 (Standard International call charges apply)

The terms HDMI™ and HDMI High-Definition Multimedia Interface, and the HDMI logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.

Contents

Chapter 1 Introduction		1
1.1	Package Contents	1
1.2	Specifications	2
1.3	Motherboard Layout	7
1.4	I/O Panel	9

Chapter 2 Installation		11
2.1	Installing the CPU	12
2.2	Installing the CPU Fan and Heatsink	15
2.3	Installing Memory Modules (DIMM)	16
2.4	Expansion Slots (PCI Express Slots)	18
2.5	Jumpers Setup	19
2.6	Onboard Headers and Connectors	20
2.7	CrossFireXTM and Quad CrossFireXTM Operation Guide	25
2.7.1	Installing Two CrossFireXTM-Ready Graphics Cards	25
2.7.2 Driver Installation and Setup		27

2.8M.2 WiFi/BT Module and Intel® CNVi (Integrated WiFi/BT)

	Installation Guide	28
2.9	M.2_SSD (NGFF) Module Installation Guide (M2_1)	30
2.10	M.2_SSD (NGFF) Module Installation Guide (M2_2)	35

Chapter 3 Software and Utilities Operation		39
3.1	Installing Drivers	39
3.2	A-Tuning	40

3.2.1	Installing A-Tuning	40
3.2.2	Using A-Tuning	40
3.3	ASRock Live Update & APP Shop	43
3.3.1	UI Overview	43
3.3.2	Apps	44
3.3.3	BIOS & Drivers	47
3.3.4	Setting	48

Chapter 4 UEFI SETUP UTILITY		49
4.1	Introduction	49
4.2	EZ Mode	50
4.3	Advanced Mode	51
4.3.1	UEFI Menu Bar	51
4.3.2	Navigation Keys	52
4.4	Main Screen	53
4.5	OC Tweaker Screen	54
4.6	Advanced Screen	64
4.6.1	CPU Configuration	65
4.6.2	Chipset Configuration	67
4.6.3	Storage Configuration	70
4.6.4	Intel® Thunderbolt	71
4.6.5	Super IO Configuration	73
4.6.6	ACPI Configuration	74
4.6.7	USB Configuration	75
4.6.8	Trusted Computing	76

4.7	Tools	77
4.8	Hardware Health Event Monitoring Screen	79
4.9	Security Screen	82
4.10	Boot Screen	83
4.11	Exit Screen	86

B360 Pro4

Chapter 1 Introduction

Thank you for purchasing ASRock B360 Pro4 motherboard, a reliable motherboard produced under ASRock’s consistently stringent quality control. It delivers excellent performance with robust design conforming to ASRock’s commitment to quality and endurance.

In this documentation, Chapter 1 and 2 contains the introduction of the motherboard and step-by-step installation guides. Chapter 3 contains the operation guide of the software and utilities. Chapter 4 contains the configuration guide of the BIOS setup.

Because the motherboard specifications and the BIOS software might be updated, the content of this documentation will be subject to change without notice. In case any modifications of this documentation occur, the updated version will be available on ASRock’s website without further notice. If you require technical support related to this motherboard, please visit our website for specific information about the model you are using. You may find the latest VGA cards and CPU support list on ASRock’s website as well. ASRock website http://www.asrock.com.

1.1 Package Contents

•ASRock B360 Pro4 Motherboard (ATX Form Factor)

•ASRock B360 Pro4 Quick Installation Guide

•ASRock B360 Pro4 Support CD

•2 x Serial ATA (SATA) Data Cables (Optional)

•1 x I/O Panel Shield

•3 x Screws for M.2 Sockets (Optional)

English

1

English

1.2 Specifications

Platform	•	ATX Form Factor
	•	Solid Capacitor design
CPU	•	Supports 8th Generation Intel® CoreTM Processors (Socket
		1151)
	•	Digi Power design
	• 10 Power Phase design
	• Supports Intel® Turbo Boost 2.0 Technology
Chipset	•	Intel® B360
Memory	•	Dual Channel DDR4 Memory Technology
	• 4 x DDR4 DIMM Slots
	• Supports DDR4 2666/2400/2133 non-ECC, un-buffered
		memory
	• Supports ECC UDIMM memory modules (operate in non-
		ECC mode)
	• Max. capacity of system memory: 64GB
	• Supports Intel® Extreme Memory Profile (XMP) 2.0
	• 15μ Gold Contact in DIMM Slots
Expansion	•	2 x PCI Express 3.0 x16 Slots (PCIE2/PCIE4: single at x16
Slot		(PCIE2); dual at x16 (PCIE2) / x4 (PCIE4))
	* If PCIE3 or PCIE5 is occupied, PCIE4 will downgrade to x2
	mode.
	* Supports NVMe SSD as boot disks
	• 3 x PCI Express 3.0 x1 Slots (Flexible PCIe)
	• Supports AMD Quad CrossFireXTM and CrossFireXTM
	• 1 x M.2 Socket (Key E), supports type 2230 WiFi/BT module
		and Intel® CNVi (Integrated WiFi/BT)
Graphics	* Intel® UHD Graphics Built-in Visuals and the VGA outputs
	can be supported only with processors which are GPU
	integrated.

2

B360 Pro4

•Supports Intel® UHD Graphics Built-in Visuals : Intel® Quick Sync Video with AVC, MVC (S3D) and MPEG-2 Full HW Encode1, Intel® InTruTM 3D, Intel® Clear Video HD Technology, Intel® InsiderTM, Intel® UHD Graphics

•DirectX 12

•HWAEncode/Decode: AVC/H.264, HEVC/H.265 8-bit, HEVC/H.265 10-bit, VP8, VP9 8-bit, VP9 10-bit (Decode only), MPEG2, MJPEG, VC-1 (Decode only)

•Three graphics output options: D-Sub, DVI-D and HDMI

•Supports Triple Monitor

•Supports HDMI with max. resolution up to 4K x 2K (4096x2160) @ 30Hz

•Supports DVI-D with max. resolution up to 1920x1200 @ 60Hz

•Supports D-Sub with max. resolution up to 1920x1200 @ 60Hz

•Supports Auto Lip Sync, Deep Color (12bpc), xvYCC and HBR (High Bit Rate Audio) with HDMI Port (Compliant HDMI monitor is required)

•Supports HDCP with DVI-D and HDMI Ports

•Supports 4K Ultra HD (UHD) playback with HDMI Port

Audio	•	7.1 CH HD Audio with Content Protection (Realtek ALC892
		Audio Codec)
	* To configure 7.1 CH HD Audio, it is required to use an HD
	front panel audio module and enable the multi-channel audio
	feature through the audio driver.
	• Premium Blu-ray Audio support
	•	Supports Surge Protection
	•	ELNA Audio Caps
LAN	•	Gigabit LAN 10/100/1000 Mb/s
	• Giga PHY Intel® I219V
	• Supports Wake-On-LAN
	•	Supports Lightning/ESD Protection
	• Supports Energy Efficient Ethernet 802.3az
	•	Supports PXE

English

3

English

Rear Panel	• 2 x Antenna Ports
I/O	• 1 x PS/2 Mouse/Keyboard Port
	• 1 x D-Sub Port
	• 1 x DVI-D Port
	• 1 x HDMI Port
	• 2 x USB 2.0 Ports (Supports ESD Protection)
	• 1 x USB 3.1 Gen2 Type-A Port (10 Gb/s) (Supports ESD
	Protection)
	• 1 x USB 3.1 Gen2 Type-C Port (10 Gb/s) (Supports ESD
	Protection)
	• 2 x USB 3.1 Gen1 Ports (Supports ESD Protection)
	• 1 x RJ-45 LAN Port with LED (ACT/LINK LED and SPEED
	LED)
	• HD Audio Jacks: Line in / Front Speaker / Microphone
Storage	• 6 x SATA3 6.0 Gb/s Connectors, support NCQ, AHCI and
	Hot Plug*

*If M2_1 is occupied by a SATA-type M.2 device, SATA3_5 will be disabled.

*If M2_2 is occupied by a SATA-type M.2 device, SATA3_0 will be disabled.

•1 x Ultra M.2 Socket (M2_1), supports M Key type 2230/2242/2260/2280 M.2 SATA3 6.0 Gb/s module and M.2 PCI Express module up to Gen3 x4 (32 Gb/s)**

•1 x M.2 Socket (M2_2), supports M Key type 2230/2242/2260/2280/22110 M.2 SATA3 6.0 Gb/s module and M.2 PCI Express module up to Gen3 x2 (16 Gb/s)**

**Supports Intel® OptaneTM Technology (M2_1 only)

**Supports NVMe SSD as boot disks

**Supports ASRock U.2 Kit

Connector	• 1 x COM Port Header
	• 1 x TPM Header
	• 1 x Power LED and Speaker Header
	• 1 x CPU Fan Connector (4-pin)
	* The CPU Fan Connector supports the CPU fan of maximum
	1A (12W) fan power.

4

B360 Pro4

•3 x Chassis/Water Pump Fan Connectors (4-pin) (Smart Fan Speed Control)

*The Chassis/Water Pump Fan supports the water cooler fan of maximum 2A (24W) fan power.

*CHA_FAN1/WP, CHA_FAN2/WP and CHA_FAN3/WP can auto detect if 3-pin or 4-pin fan is in use.

•1 x 24 pin ATX Power Connector

•1 x 8 pin 12V Power Connector

•1 x Front Panel Audio Connector

•1 x Thunderbolt AIC Connector (5-pin)

•2 x USB 2.0 Headers (Support 3 USB 2.0 ports) (Supports ESD Protection)

•1 x USB 3.1 Gen1 Header (Supports 2 USB 3.1 Gen1 ports) (Supports ESD Protection)

BIOS	•	AMI UEFI Legal BIOS with multilingual GUI support
Feature	•	ACPI 6.0 Compliant wake up events
	•	SMBIOS 2.7 Support
	• DRAM, PCH 1.0V, VCCIO, VCCST, VCCSA, VPPM Voltage
		Multi-adjustment
Hardware	•	Temperature Sensing: CPU, Chassis/Water Pump Fans
Monitor	•	Fan Tachometer: CPU, Chassis/Water Pump Fans
	• Quiet Fan (Auto adjust chassis fan speed by CPU tempera-
		ture): CPU, Chassis/Water Pump Fans
	• Fan Multi-Speed Control: CPU, Chassis/Water Pump Fans
	• Voltage monitoring: +12V, +5V, +3.3V, CPU Vcore, DRAM,
		VPPM, PCH 1.0V, VCCSA, VCCST
OS	•	Microsoft® Windows® 10 64-bit
Certifica-	•	FCC, CE
tions	•	ErP/EuP ready (ErP/EuP ready power supply is required)

* For detailed product information, please visit our website: http://www.asrock.com

English

5

Please realize that there is a certain risk involved with overclocking, including adjusting the setting in the BIOS, applying Untied Overclocking Technology, or using third-party overclocking tools. Overclocking may affect your system’s stability, or even cause damage to the components and devices of your system. It should be done at your own risk and expense. We are not responsible for possible damage caused by overclocking.

English

6

B360 Pro4

1.3 Motherboard Layout

1

2

3

4

5

Antenna Port

US
B: USB3T: 3_2 _1	US3.B Gen1	/Mous Keyboard PS2 e
	DVI1		VGA1
HDMI1

USB 3.1 Gen2

T:USB31_TA_1

B: USB31_TC_1

	USB 2.0	Top:
	T: USB_1
		RJ-45
	B: USB_2

INMI Bottom C :	FRON Center: T	LINE Top:

LAN

AUDIO

CODEC

24

23

ATX12V1

USB 3.1

PCIE1

M2_3_CT1

PCIE3

		PCIE5
HD_AUDIO1		COM1
1	1	1

CPU_FAN1

				DDR4 A1(64bit,288-pinmodule)	DDR4 A2(64bit,288-pinmodule)	DDR4 B1(64bit,288-pinmodule)
		CHA_FAN2/WP
			Ultra M.2	AMD
			PCIe Gen3 x4
				CROSSFIRE
CT1	CT2	CT3	CT4	M2 1

PCIE2

PCI Express 3.0

_3
M2	CMOS
SUPER	Battery
I/O	Intel
	B360

DDR4_B2 (64 bit, 288-pin module)

ATXPWR1

	USB3 3 4
	1
SATA3 2	SATA3 3
SATA3 0	SATA3 1

B360 Pro4

PCIE4

T B1

1

	RoHS					M2 2
	CT5	CT6	CT7	CT8
				SPK_PLED1
CLRMOS1
				1
1			CHA_FAN3/WP	PANEL1
TPMS1		CHA_FAN1/WP			SATA3_5	SATA3_4
	USB_3_4			PLED PWRBTN
	USB_5
1	1			1
				HDLED RESET

22

21

20

19

18

17

16

15

14

13

6

7

8

9

10

11

12

English

7

No. Description

1ATX 12V Power Connector (ATX12V1)

2Chassis Fan / Waterpump Fan Connector (CHA_FAN2/WP)

3CPU Fan Connector (CPU_FAN1)

42 x 288-pin DDR4 DIMM Slots (DDR4_A1, DDR4_B1)

52 x 288-pin DDR4 DIMM Slots (DDR4_A2, DDR4_B2)

6ATX Power Connector (ATXPWR1)

7USB 3.1 Gen1 Header (USB3_3_4)

8SATA3 Connector (SATA3_3)

9SATA3 Connector (SATA3_2)

10SATA3 Connector (SATA3_1)

11SATA3 Connector (SATA3_0)

12Power LED and Speaker Header (SPK_PLED1)

13SATA3 Connector (SATA3_4)

14SATA3 Connector (SATA3_5)

15System Panel Header (PANEL1)

16Chassis Fan / Waterpump Fan Connector (CHA_FAN3/WP)

17Chassis Fan / Waterpump Fan Connector (CHA_FAN1/WP)

18USB 2.0 Header (USB_3_4)

19USB 2.0 Header (USB_5)

20TPM Header (TPMS1)

21COM Port Header (COM1)

22Front Panel Audio Header (HD_AUDIO1)

23Clear CMOS Jumper (CLRMOS1)

24Thunderbolt AIC Connector (TB1)

English

8

B360 Pro4

1.4 I/O Panel

																						5
	1			2						3						4						6

	13	12	11	10	9	8	7
No.	Description			No.	Description
1	PS/2 Mouse/Keyboard Port			8	USB 2.0 Ports (USB_1_2)
2	D-Sub Port			9	USB 3.1 Gen2 Type-C Port (USB31_TC_1)
3	USB 3.1 Gen2 Type-A Port (USB31_TA_1)			10	HDMI Port
4	LAN RJ-45 Port*			11	DVI-D Port
5	Line In (Light Blue)**			12	USB 3.1 Gen1 Ports (USB3_1_2)
6	Front Speaker (Lime)**			13	Antenna Ports
7	Microphone (Pink)**

* There are two LEDs on each LAN port. Please refer to the table below for the LAN port LED indications.

ACT/LINK LED

SPEED LED

LAN Port

Activity / Link LED			Speed LED
Status		Description	Status		Description
Off		No Link	Off		10Mbps connection
Blinking		Data Activity	Orange		100Mbps connection
On		Link	Green		1Gbps connection

English

9

** To configure 7.1 CH HD Audio, it is required to use an HD front panel audio module and enable the multichannel audio feature through the audio driver.

Please set Speaker Configuration to “7.1 Speaker”in the Realtek HD Audio Manager.

Function of the Audio Ports in 7.1-channel Configuration:

Port		Function
Light Blue (Rear panel)		Rear Speaker Out
Lime (Rear panel)		Front Speaker Out
Pink (Rear panel)		Central /Subwoofer Speaker Out
Lime (Front panel)		Side Speaker Out

English

10

B360 Pro4

Chapter 2 Installation

This is an ATX form factor motherboard. Before you install the motherboard, study the configuration of your chassis to ensure that the motherboard fits into it.

Pre-installation Precautions

Take note of the following precautions before you install motherboard components or change any motherboard settings.

•Make sure to unplug the power cord before installing or removing the motherboard components. Failure to do so may cause physical injuries and damages to motherboard components.

•In order to avoid damage from static electricity to the motherboard’s components, NEVER place your motherboard directly on a carpet. Also remember to use a grounded wrist strap or touch a safety grounded object before you handle the components.

•Hold components by the edges and do not touch the ICs.

•Whenever you uninstall any components, place them on a grounded anti-static pad or in the bag that comes with the components.

•When placing screws to secure the motherboard to the chassis, please do not overtighten the screws! Doing so may damage the motherboard.

English

11

2.1Installing the CPU

1.Before you insert the 1151-Pin CPU into the socket, please check if the PnP cap is on the socket, if the CPU surface is unclean, or if there are any bent pins in the socket. Do not force to insert the CPU into the socket if above situation is found. Otherwise, the CPU will be seriously damaged.

2.Unplug all power cables before installing the CPU.

1

A

B

2

English

12

B360 Pro4

3

4

5

English

13

Please save and replace the cover if the processor is removed. The cover must be placed if you wish to return the motherboard for after service.

English

14

B360 Pro4

2.2 Installing the CPU Fan and Heatsink

1

2

N _FA PU C

English

15

2.3 Installing Memory Modules (DIMM)

This motherboard provides four 288-pin DDR4 (Double Data Rate 4) DIMM slots, and supports Dual Channel Memory Technology.

1.For dual channel configuration, you always need to install identical (the same brand, speed, size and chip-type) DDR4 DIMM pairs.

2.It is unable to activate Dual Channel Memory Technology with only one or three memory module installed.

3.It is not allowed to install a DDR, DDR2 or DDR3 memory module into a DDR4 slot; otherwise, this motherboard and DIMM may be damaged.

Dual Channel Memory Configuration

Priority	DDR4_A1	DDR4_A2	DDR4_B1	DDR4_B2
1		Populated		Populated
2	Populated	Populated	Populated	Populated

The DIMM only fits in one correct orientation. It will cause permanent damage to the motherboard and the DIMM if you force the DIMM into the slot at incorrect orientation.

English

16

B360 Pro4

1

2

3

English

17

2.4 Expansion Slots (PCI Express Slots)

There are 5 PCI Express slots on the motherboard.

Before installing an expansion card, please make sure that the power supply is switched off or the power cord is unplugged. Please read the documentation of the expansion card and make necessary hardware settings for the card before you start the installation.

PCIe slots:

PCIE1 (PCIe 3.0 x1 slot) is used for PCI Express x1 lane width cards.

PCIE2 (PCIe 3.0 x16 slot) is used for PCI Express x16 lane width graphics cards. PCIE3 (PCIe 3.0 x1 slot) is used for PCI Express x1 lane width cards.

PCIE4 (PCIe 3.0 x16 slot) is used for PCI Express x4 lane width graphics cards. PCIE5 (PCIe 3.0 x1 slot) is used for PCI Express x1 lane width cards.

* If PCIE3 or PCIE5 is occupied, PCIE4 will downgrade to x2 mode.

PCIe Slot Configurations

		PCIE2	PCIE4
	Single Graphics Card	x16	N/A
	Two Graphics Cards in	x16	x4
	CrossFireXTM Mode

For a better thermal environment, please connect a chassis fan to the motherboard’s chassis fan connector (CHA_FAN1/WP, CHA_FAN2/WP or CHA_FAN3/WP) when using mul-tiple graphics cards.

English

18

B360 Pro4

2.5 Jumpers Setup

The illustration shows how jumpers are setup. When the jumper cap is placed on the pins, the jumper is “Short”. If no jumper cap is placed on the pins, the jumper is “Open”. The illustration shows a 3-pin jumper whose pin1 and pin2 are “Short” when a jumper cap is placed on these 2 pins.

	Clear CMOS Jumper
	(CLRMOS1)	Default	Clear CMOS
	(see p.7, No. 23)

CLRMOS1 allows you to clear the data in CMOS. To clear and reset the system parameters to default setup, please turn off the computer and unplug the power cord from the power supply. After waiting for 15 seconds, use a jumper cap to short pin2 and pin3 on CLRMOS1 for 5 seconds. However, please do not clear the CMOS right after you update the BIOS. If you need to clear the CMOS when you just finish updating the BIOS, you must boot up the system first, and then shut it down before you do the clear-CMOS action. Please be noted that the password, date, time, and user default profile will be cleared only if the CMOS battery is removed.

English

19

2.6 Onboard Headers and Connectors

Onboard headers and connectors are NOT jumpers. Do NOT place jumper caps over these headers and connectors. Placing jumper caps over the headers and connectors will cause permanent damage to the motherboard.

System Panel Header

(9-pin PANEL1)

(see p.7, No. 15)

PLED+ PLED-

PWRBTN#

GND

1

GND RESET#

GND HDLED-

HDLED+

Connect the power button, reset button and system status indicator on the chassis to this header according to the pin assignments below. Note the positive and negative pins before connecting the cables.

PWRBTN (Power Button):

Connect to the power button on the chassis front panel. You may configure the way to turn off your system using the power button.

RESET (Reset Button):

Connect to the reset button on the chassis front panel. Press the reset button to restart the computer if the computer freezes and fails to perform a normal restart.

PLED (System Power LED):

Connect to the power status indicator on the chassis front panel. The LED is on when the system is operating. The LED keeps blinking when the system is in S1/S3 sleep state. The LED is off when the system is in S4 sleep state or powered off (S5).

HDLED (Hard Drive Activity LED):

Connect to the hard drive activity LED on the chassis front panel. The LED is on when the hard drive is reading or writing data.

The front panel design may differ by chassis. A front panel module mainly consists of power button, reset button, power LED, hard drive activity LED, speaker and etc. When connecting your chassis front panel module to this header, make sure the wire assignments and the pin assignments are matched correctly.

English

20

B360 Pro4

Power LED and Speaker

Header

(7-pin SPK_PLED1)

(see p.7, No. 12)

SPEAKER

DUMMY DUMMY +5V

1

PLED+

PLED+ PLED-

Please connect the chassis power LED and the chassis speaker to this header.

Serial ATA3 Connectors (SATA3_0:

see p.7, No. 11) (SATA3_1: see p.7, No. 10) (SATA3_2: see p.7, No. 9) (SATA3_3: see p.7, No. 8) (SATA3_4: see p.7, No. 13) (SATA3_5: see p.7, No. 14)

USB 2.0 Headers

(9-pin USB_3_4)

(see p.7, No. 18)

(4-pin USB_5)

(see p.7, No. 19)

SATA3 2	SATA3 3
SATA3 0	SATA3 1

SATA3_5 SATA3_4

These six SATA3 connectors support SATA data cables for internal storage devices with up to 6.0 Gb/s data transfer rate.

*If M2_1 is occupied by a SATA-type M.2 device, SATA3_5 will be disabled.

*If M2_2 is occupied by a SATA-type M.2 device, SATA3_0 will be disabled.

USB_PWR

P- P+ GND DUMMY

1

GND

USBP_-PWRP+

1

GND

USBP_-PWRP+

There are two USB 2.0 headers on this motherboard.

English

21

USB 3.1 Gen1 Header

(19-pin USB3_3_4)

(see p.7, No. 7)

Vbus

IntA_PA_SSRX-

IntA_PA_SSRX+

GND

IntA_PA_SSTX-

IntA_PA_SSTX+

GND

IntA_PA_D-

IntA_PA_D+

Vbus

IntA_PB_SSRX-

IntA_PB_SSRX+

GND

IntA_PB_SSTX-

IntA_PB_SSTX+

GND

IntA_PB_D-

IntA_PB_D+

Dummy

1

There is one header on this motherboard. This USB 3.1 Gen1 header can support two ports.

Front Panel Audio Header

(9-pin HD_AUDIO1)

(see p.7, No. 22)

GND PRESENCE#

MIC_RET

OUT_RET

1

OUT2_L J_SENSE

OUT2_R MIC2_R

MIC2_L

This header is for connecting audio devices to the front audio panel.

1.High Definition Audio supports Jack Sensing, but the panel wire on the chassis must support HDA to function correctly. Please follow the instructions in our manual and chassis manual to install your system.

2.If you use an AC’97 audio panel, please install it to the front panel audio header by the steps below:

A.Connect Mic_IN (MIC) to MIC2_L.

B.Connect Audio_R (RIN) to OUT2_R and Audio_L (LIN) to OUT2_L.

C.Connect Ground (GND) to Ground (GND).

D.MIC_RET and OUT_RET are for the HD audio panel only. You don’t need to connect them for the AC’97 audio panel.

E.To activate the front mic, go to the “FrontMic” Tab in the Realtek Control panel and adjust “Recording Volume”.

Chassis Fan / Waterpump

Fan Connectors

(4-pin CHA_FAN1/WP)

(see p.7, No. 17)

(4-pin CHA_FAN2/WP)

(see p.7, No. 2)

(4-pin CHA_FAN3/WP)

(see p.7, No. 16)

English

4 3 2 1

FAN_SPEED_CONTROL

CHA_FAN_SPEED FAN_VOLTAGE

GND

Please connect fan cables to the fan connectors and match the black wire to the ground pin.

22

CPU Fan Connector

(4-pin CPU_FAN1)

(see p.7, No. 3)

ATX Power Connector

(24-pin ATXPWR1)

(see p.7, No. 6)

ATX 12V Power

Connector

(8-pin ATX12V1)

(see p.7, No. 1)

Serial Port Header

(9-pin COM1)

(see p.7, No. 21)

TPM Header

(17-pin TPMS1)

(see p.7, No. 20)

B360 Pro4

FAN_VOLTAGE CPU_FAN_SPEED

GND FAN_SPEED_CONTROL

1 2 3 4

This motherboard provides a 4-Pin CPU fan (Quiet Fan) connector. If you plan to connect a 3-Pin CPU fan, please connect it to Pin 1-3.

12 24

1 13

This motherboard provides a 24-pin ATX power connector. To use a 20-pin ATX power supply, please plug it along Pin 1 and Pin 13.

This motherboard pro-

8

5

vides an 8-pin ATX 12V

power connector. To use a

4-pin ATX power supply,

4

1

please plug it along Pin 1

and Pin 5.

RRXD1

This COM1 header

DDTR#1

supports a serial port

DDSR#1

CCTS#1

1

RRI#1

module.

RRTS#1

GND

TTXD1

DDCD#1

SMB CLK MAIN

SMB DATA MAIN

GND S PWRDWN#

This connector supports Trusted

SERIRQ#

Platform Module (TPM) system,

GND

LAD2

LAD1

GND

which can securely store keys,

digital certificates, passwords,

1

and data. A TPM system also

helps enhance network security,

PCICLK

FRAME

PCIRST#

LAD3

+3V

LAD0

+3VSB

GND

protects digital identities, and

English

ensures platform integrity.

23