Instruction booklet
|
|
|
WASHER DRYER |
|
|
|
|
|
|
|
|
|
Contents |
|
|
GB |
|
GB |
|
|
|
|
||
|
|
|
Installation, 2-3 |
|
|
English |
|
||
|
|
|
Unpacking |
|
|
|
|
Remove the transit fixings |
|
|
|
|
Levelling |
|
|
|
|
Water connections |
|
|
|
|
Drainage and electrical connections |
|
|
|
|
Technical details |
|
|
|
|
Washer dryer description, 4-5 |
|
|
|
|
Control panel |
|
|
|
|
LEDs |
|
|
|
|
Starting and programmes, 6-9 |
|
|
|
|
Briefly: how to start a programme |
|
|
|
|
Programmes table |
|
|
|
|
Setting the temperature |
|
|
A1600WD |
Setting the spin speeds |
|
|
|
A1400SWD |
Functions |
|
|
|
Drying section |
|
||
|
A1400WD |
|
||
|
|
|
||
|
A1200WD |
Detergents and laundry, 10 |
|
|
|
|
|
Detergent dispenser |
|
|
|
|
Preparing your laundry |
|
|
|
|
Special items |
|
|
|
|
Precautions and Advice, 11 |
|
|
|
|
General safety |
|
|
|
|
Disposal |
|
|
|
|
Saving energy and respecting the environment |
|
|
|
|
Care and Maintenance, 12 |
|
|
|
|
Switching off the water or electricity supply |
|
|
|
|
Cleaning |
|
|
|
|
Caring for your appliance door and drum |
|
|
|
|
Checking the water inlet hoses |
|
|
|
|
Fuses |
|
|
|
|
Changing the plug |
|
|
|
|
Troubleshooting, 13-14 |
|
|
|
|
Service, 15 |
|
|
|
|
Before calling for assistance |
|
|
|
|
Spare parts |
|
1
Installation
GB
! Keep this instruction manual in a safe place for future reference. Should the appliance be sold, transferred or moved, make sure the instruction manual accompanies the washer dryer to inform the new owner as to its operation and features.
! Read these instructions carefully: they contain vital information on installation, use and safety.
Unpacking
1.Unpack the machine.
2.Check whether the washer dryer has been damaged during transport. If this is the case, do not install it and contact your retailer.
Remove the transit fixings
IMPORTANT: Follow these instructions to remove the TWO transit fixings.
Situated one either side of the rear panel, BOTH transit bolts
MUST be removed before use.
! Failure to do so may cause damage to your machine.
It is important the transit bolt and spacer (see pic) come out intact.
1. Unscrew the bolt using a 13mm spanner.
2. STOP when 3 threads can be seen.
3. Hold, slide sideways and pull to remove.
4. For safety, insert one of the plastic covers (supplied with your machine) over the hole.
! Repeat steps 1 to 4 to remove the second transit bolt.
! Packaging materials are not childrens toys.
Levelling
1.Install the machine on a flat sturdy floor, without resting it up against walls, cabinets etc.
2.Compensate for any unevenness by tightening or loosening the adjustable front feet. When adjusting the feet, use a spirit level to check the machine
stands level, from side to side and from front to back.
Levelling your appliance correctly will provide it with stability and avoid any vibrations, noise and shifting during operation. If it is placed on a fitted or loose carpet, adjust the feet in such a way as to allow enough room for ventilation beneath the machine.
Water connection
Connecting the water inlet hose.
Remember that this is a cold-fill machine and the fill hose fitted to the rear of the machine must be connected to the cold water supply.
Before making the connections to the water outlet, allow the water to run freely from the cold water supply tap until it is perfectly clear.
Screw the cold water fill hose onto the cold water supply tap until tight.
Turn the tap on and check for leaks: tighten if necessary.
!Make sure there are no kinks or bends in the hose.
!The water pressure at the tap must be within the values indicated in the Technical details table (next page).
!If the water inlet hose is not long enough, contact a specialist store or an authorised serviceman.
!Always use new hoses.
!Check the water hose at least once a year, replace any that are cracked as worn hoses could split under water pressure.
2
Installation
Drainage connections
|
|
|
|
|
A. Connect the drain |
|
|
|
B |
|
hose, without kinking it, |
|
|
|
|
||
|
|
|
|
|
to a draining duct or a |
|
A |
||||
|
|
|
|
|
wall drain fixed at a |
|
|
|
|
|
height between 65 and |
|
|
|
|
|
100cm from the floor. |
|
|
|
|
|
Use the curved bracket, |
|
|
|
|
|
if reqired. |
|
|
|
|
|
B. Alternatively, place |
|
|
|
|
|
it over the edge of a |
|
|
|
|
|
basin, sink or tub, |
|
|
|
|
|
fastening the hose |
|
|
|
|
|
supplied to the tap. |
!The free end of the hose should not be under water.
!We advise against the use of hose extensions. In case of absolute need, the extension must have the same diameter as the original hose and must not exceed 150cm in length.
Electrical connections
Before plugging the appliance into the mains socket, make sure that:
●the socket is earthed and in compliance with the applicable law.
●the socket is able to sustain the appliances maximum power load indicated in the Technical Details table (on the right).
●the supply voltage is included within the values indicated in the Technical Details table (on the right).
●the socket is compatible with the machines plug. If this is not the case, replace the socket or the plug.
!The machine should not be installed in an outdoor environment, not even when the area is sheltered, because it may be very dangerous to leave it exposed to rain and thunderstorms.
!When the machine is installed, the mains socket must be within easy reach and should be connected to a suitable electrical supply.
!Do not use extensions or multiple sockets.
!The power supply cable must never be bent or dangerously compressed.
!The power supply cable must only be replaced by an authorised serviceman.
!The company denies all liability if and when these norms are not respected.
The first wash cycle
GB
Once the appliance has been installed and before you use it for the first time, run a wash cycle without detergent and no laundry, setting the 90˚C programme without a pre-wash cycle.
Technical Details
Models |
A1600WD, A1400SWD, |
|
|
A1400WD, A1200WD |
|
|
|
|
|
59.5cm wide |
|
Dimensions |
85cm high |
|
|
60cm deep |
|
|
|
|
Capacity |
from 1 to 6kg |
|
|
|
|
Electric |
voltage 220/240 Volts 50Hz |
|
connections |
maximum absorbed power: |
|
|
1700W-2100W |
|
|
|
|
Water |
maximum pressure 1 MPa (10 bar) |
|
connections |
minimum pressure 0.05 MPa (0.5 bar) |
|
|
drum capacity 53 litres |
|
|
|
|
Spin Speed |
up to 1600 rpm - |
A1600WD |
|
up to 1400 rpm - |
A1400SWD, |
|
|
A1400WD |
|
up to 1200 rpm - |
A1200WD |
|
|
|
Control |
programme 3 |
|
programmes |
temperature 60˚C |
|
according to |
|
|
IEC50229 |
- dry run with a 1kg load followed by |
|
directive |
a 5kg load for model A1600WD |
|
|
- dry run with a 2kg load followed by |
|
|
a 4kg load for models A1400SWD, |
|
|
A1400WD and A1200WD |
This appliance is compliant with the following European Community Directives:
- 72/23/CEE of 19/02/73
(Low Voltage) and subsequent amendments. - 89/336/CEE of 03/05/89 (Electromagnetic Compatibility) and subsequent amendments.
3
Washer Dryer Description
GB |
Control panel - Models A1600 and A1400 |
|
|
|
|
|
|
|
|
|
FUNCTION |
|
ON/OFF |
||
|
PROGRESS INDICATOR |
Buttons |
|
Button |
|||
|
|
|
|
ON-OFF/DOOR LOCK |
|||
|
Programme key |
|
LEDs |
|
|
|
|
|
|
|
|
|
|
LED |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
TEMPERATURE |
|
DRYING |
|
|
|
PROGRAMME |
|
|
|
|
|
|
|||
|
|
|
|
|
|
|||
|
|
|
|
|
|
|||
|
Detergent dispenser |
Knob |
|
|
START/RESET |
|
||
|
|
|
Knob |
|||||
|
|
|
Knob |
|
Button |
|
||
|
|
|
|
|
||||
|
|
|
|
|
|
Control panel - Model A1200
|
FUNCTION |
|
ON/OFF |
|||
|
|
|||||
|
|
|
Buttons |
|
||
PROGRESS INDICATOR |
|
|
Button |
|||
|
|
|||||
|
|
|
||||
|
|
|
|
ON-OFF/DOOR LOCK |
||
Programme key |
LEDs |
|
|
|
|
|
|
|
|
|
|
LED |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
TEMPERATURE |
|
DRYING |
|
|
|
|
PROGRAMME |
|
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
|||
|
Detergent dispenser |
Knob |
|
|
|
START/RESET |
|
||
|
|
|
Knob |
||||||
|
|
|
Knob |
|
|
Button |
|
||
|
|
|
|
|
|
||||
|
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
Detergent dispenser:
To add detergent and fabric softener (see Detergents and Laundry).
Programme key:
To consult a straightforward chart of the different programmes available.
PROGRESS INDICATOR LEDs:
To find out which cycle phase is under way.
The corresponding LED for the cycle in progress is illuminated.
DRYING knob:
A1200 - To set the drying time
A1400 - To set the drying time and single level auto dry.
A1600 - To set the drying time and 3 level auto drying (see Starting and Programmes).
FUNCTION buttons:
To select the functions available (see Starting and Programmes).
When a function is selected, the corresponding LED is illuminated.
TEMPERATURE knob:
To set the temperature or the cold wash cycle (see Starting and Programmes).
ON/OFF button:
To turn the machine on and off.
START/RESET button:
To start the programme or cancel any incorrect settings.
ON-OFF/DOOR LOCK LED:
To find out whether the machine is on and if the appliance door can be opened.
PROGRAMME knob:
To select the programme you require.
The retractable control knob: press the centre of the knob for it to pop out. The knob stays still during the cycle.
4
Washer Dryer Description
LEDs
PROGRESS INDICATOR LEDs:
These light up to indicate the progress of the selected programme.
When the programme is started the light corresponding to the first cycle is lit and as the programme progresses, successive lights will come on until the programme finishes.
FUNCTION buttons / LEDs:
When a function is selected, the corresponding LED is illuminated.
●If the function selected is incompatible with the programme set, the button will flash and the function will not be enabled.
●If you set a function that is incompatible with another function you selected previously, only the last one selected will be enabled.
ON-OFF/DOOR LOCK LED:
If this LED is on, the appliance door is locked to prevent it from being opened accidentally; to avoid any damage. Wait for the LED to flash before you open the appliance door.
! The rapid flashing of the ON-OFF/DOOR LOCK LED together with the flashing of at least one other LED indicates there is an error. Call for Technical Assistance.
Additional feature - Models A1600WD, A1400SWD
and A1400WD only: |
GB |
|
Your machine has a delay timer function and there are additional markings alongside the LEDs.
DELAY TIMER set:
If the Delay Timer function has been enabled (see Starting and Programmes), once you start the programme the LED corresponding to the delay set will begin to flash.
As time passes, the remaining delay will be displayed and the corresponding LED will flash:
Once the set delay is complete, the flashing LED will turn off and the selected programme will start.
Automatic Rinse hold
●Models A1600 and A1400
Note: If you have selected a synthetic wash programme, the machine will automatically stop in
the final rinse and the LED will flash, press the START/RESET button to continue to the end of the programme (wash programme only).
If drying option has been selected the machine will complete the programme without any interruption.
●Model A1200
Note: If you have selected a synthetic wash programme together with the reduced creases option, the machine will automatically stop in
the final rinse and the LED will flash, press the START/RESET button to continue to the end of the programme (wash or wash and dry
programme).
5