AA1403001-E5-A
XFP, 10GBASE-LR 10G Ethernet Module
1310nm, 10km, SMF, LC RoHS6
_______________________________________________________
AA1403001-E5-A
10Gbps XFP Transceiver
Features
• Supports 9.95Gb/s to 11.1Gb/s bit rates
• Hot-pluggable XFP footprint
• Maximum link length of 10km
• Uncooled 1310nm EML/DFB laser
• Duplex LC connector
• Power dissipation <2.5W
• Built-in digital diagnostic functions
• Temperature range -5°C to 70°C
Regulatory Compliance
Applications
SONET OC-192 SR-1 SDH STM
I-64.1 at 9.953Gbps
10GBASE-LR/LW 10G Ethernet
1200-SM-LL-L 10G Fiber Channel
10GE over G.709 at 11.09Gbps
OC192 over FEC at 10.709Gbp
Feature Standard Performance
Electrostatic Discharge (ESD)
to the Electrical Pins
Electromagnetic Interference
(EMI)
Laser Eye Safety
Component Recognition UL and CUL UL file E317337
Green Products RoHS RoHS6
MIL-STD-883E Method
3015.7
FCC Part 15 Class B
FDA 21CFR 1040.10 and
1040.11 EN60950, EN (IEC)
60825-1,2
Class 1(>500 V)
Compatible with
standards
Compatible with Class I
laser product.
Compatible with TμV
standards
Approved Optics, Inc. www.ApprovedOptics.com
Page 1 of 5
AA1403001-E5-A
XFP, 10GBASE-LR 10G Ethernet Module
1310nm, 10km, SMF, LC RoHS6
_______________________________________________________
Absolute Maximum Ratings
Parameter Symbol
Maximum Supply Voltage 1 VCC3
Maximum Supply Voltage 2 VCC5
Storage Temperature Ts
Case Operating Temperature Top
Recommended Operating Conditions
Parameter Symbol Min.
Operating Temperature Top -5
Supply Voltage 1 VCC3 3.13
Supply Voltage 2 VCC5 4.75
Min. Max. Unit
-0.5 4.0 V
-0.5 6.0 V
-40 85 °C
-5 70 °C
Typical
Max. Unit
70 °C
3.45 V
5.25 V
Electrical Characteristics
(TOP = -5 to 70°C, VCC5 = 4.75 to 5.25 Volts)
Parameter Symbol Min Typ Max Unit Note
Main Supply Voltage Vcc5 4.75
Supply Voltage S#2 Vcc3 3.13
Supply Current Vcc5 Icc5
Supply Current Vcc3 Icc3
Module total power P
Transmitter
Input differential impedance Rin
Differential data input swing Vin,pp 120
Transmit Disable Voltage VD 2
Transmit Enable Voltage VEN GND
Transmit Disable Assert
Time
Receiver
Differential data output swing Vout,pp 340 650 850 mV
Data output rise time tr
Data output fall time tf
LOS Fault VLOS fault
Vcc–
0.5
100
5.25 V
3.45 V
250 mA
500 mA
2.5 W
820 mV
Vcc V
GND+0.8 V
10 us
38 ps 2
38 ps 2
VccHOST V 3
Ω
1
Approved Optics, Inc. www.ApprovedOptics.com
Page 2 of 5
AA1403001-E5-A
XFP, 10GBASE-LR 10G Ethernet Module
1310nm, 10km, SMF, LC RoHS6
_______________________________________________________
LOS Normal
Power Supply Rejection PSR See Note 4 below 4
VLOS
norm
GND
GND+0.5 V
Notes
1. After internal AC coupling.
2. 20 – 80 %
3. Loss of signal is open collector to be pulled up with a 4.7k–10kohm resistor to 3.15–
3.6V. Logic 0 indicates normal operation; logic 1 indicates no signal detected.
4. Per Section 2.7.1. in the XFP MSA Specification.
Optical Characteristics
(TOP = -5 to 70°C, VCC5 = 4.75 to 5.25 Volts)
Parameter Symbol Min. Typ. Max Unit Ref.
Transmitter
Optical output Power P -6
Optical Wavelength
Optical Extinction Ratio ER 6
Sidemode Suppression ratio SSRmin
Average Launch power of OFF
transmitter
Tx Jitter Txj Compliant with each standard requirements
Receiver
Receiver Sensitivity (OMA) @
10.7Gb/s
Maximum Input Power PMAX +0.5
Optical Center Wavelength λC 1270
Receiver Reflectance Rrx
LOS De-Assert LOSD
LOS Assert LOSA -32
LOS Hysteresis
λ
POFF -30
RSENS
1290
1
1310
0 dBm
1330 nm
30 dB
-14.5 dBm
1600 nm
-14 dB
-18 dBm
dB
dBm
dBm
dBm
dB
General Specifications
Approved Optics, Inc. www.ApprovedOptics.com
Page 3 of 5
AA1403001-E5-A
XFP, 10GBASE-LR 10G Ethernet Module
1310nm, 10km, SMF, LC RoHS6
_______________________________________________________
Parameter Symbol Min Typ Max Units
Bit Rate BR 9.95
Bit Error Ratio BER
Max. Supported Link Length LMAX 10
MTBF HRS 715,000
11.1 Gb/s
10-12
km
hrs
Digital Diagnostic Functions
AA1403001-E5-A 10Gb/s (XFP) transceivers are compliant with the current XFP MultiSource Agreement (MSA) Specification Rev 4.5.
As defined by the XFP MSA, XFP transceivers provide digital diagnostic
functions via a 2-wire serial interface, which allows real-time access to the following
operating parameters:
• Transceiver temperature
• Laser bias current
• Transmitted optical power
• Received optical power
• Transceiver supply voltage
It also provides a sophisticated system of alarm and warning flags, which may be
used to alert end-users when particular operating parameters are outside of a factoryset normal range.
The operating and diagnostics information is monitored and reported by a Digital
Diagnostics Transceiver Controller inside the transceiver, which is accessed through
the 2-wire serial interface. When the serial protocol is activated, the serial clock
signal (SCL pin) is generated by the host. The positive edge clocks data into the
XFP transceiver into those segments of its memory map that is not write-protected.
The negative edge clocks data from the XFP transceiver. The serial data signal (SDA
pin) is bi-directional for serial data transfer. The host uses SDA in conjunction with
SCL to mark the start and end of serial protocol activation. The memories are
organized as a series of 8-bit data words that can be addressed individually or
sequentially. The 2-wire serial interface provides sequential or random access to the 8
bit parameters, addressed from 000h to the maximum address of the memory.
Approved Optics, Inc. www.ApprovedOptics.com
Page 4 of 5
AA1403001-E5-A
XFP, 10GBASE-LR 10G Ethernet Module
1310nm, 10km, SMF, LC RoHS6
_______________________________________________________
Mechanical Specifications
Approved Optics XFP transceivers are compliant with the dimensions defined by the
XFP Multi-Sourcing Agreement (MSA).
Contact Information
Approved Optics is a leading supplier of Network Transceivers and Connectivity
products to Channel Partners, Resellers, and OEMs. With more than 9 years of direct
industry experience, our products are resident in the most demanding and mission
critical functional networks Worldwide. We serve as a Master Distributor to the largest
CM’s in the world and deploy the most rigorous testing and firmware management
programs to bring the highest level of functional product to the market at a cost that
makes sense.
Corporate Offices:
Approved Optics
Tel: 800.590.9535
Web: http://www.ApprovedOptics.com
Approved Optics, Inc. www.ApprovedOptics.com
Page 5 of 5
Loading...