Apple IPOD HI-FI User Manual

4.5 (2)

iPod Hi-Fi

User’s Guide

Guide de l’utilisateur

Manual del usuario

K Apple Computer, Inc.

© 2006 Apple Computer, Inc. All rights reserved.

Apple, the Apple logo, AirMac, and iPod are trademarks of Apple Computer, Inc., registered in the U.S. and other countries. AirPort Express, iPod Hi-Fi, and MacBook are trademarks of Apple Computer, Inc.

Contents

5 iPod Hi-Fi User’s Guide

29

53 iPod Hi-Fi Guide de l’utilisateur

79 iPod Hi-Fi Manual del usuario

3

iPod Hi-Fi

User’s Guide

Contents

9 Chapter: 1 “Welcome”

10“iPod Hi-Fi Front View”

11“iPod Hi-Fi Rear View”

12Chapter: 2 “Setting Up Your iPod Hi-Fi”

12“Step 1: Plug In Your iPod Hi-Fi or Insert Batteries”

13“Step 2: Connect Your iPod”

14“Step 3: Play Music”

15Chapter: 3 “Using Your iPod Hi-Fi”

15“Connecting iPod”

16“Changing iPod Screen Settings”

16 “Connecting Other Audio Devices or an iPod Without a Dock Connector”

18 “Adjusting the Sound”

20 “Using the Apple Remote”

23“Saving Battery Life”

24Chapter: 4 “Tips and Troubleshooting”

26 Chapter: 5 “Learning More, Service, and Support”

7

Welcome

1

 

 

 

Congratulations on your new iPod Hi-Fi.

Your iPod Hi-Fi is a high-quality portable speaker system that plays music from any iPod. You can also use it to play music from other audio devices.

iPod Hi-Fi

Apple Remote

Power cord

iPod dock adapters

Note: Your power cord may look different from the one pictured here.

9

Apple IPOD HI-FI User Manual

iPod Hi-Fi Front View

Infrared (IR)

iPod connector

Volume control buttons

Status light

receiver

 

 

 

Wide-range driver

Woofer

Tuned bass reflex ports

Wide-range driver

Removable speaker grille

Note: You can use your iPod Hi-Fi with the speaker grille on or off. To best protect the speakers, leave the grille on. To avoid damage to the speakers, do not touch the speaker cones.

10 Chapter 1 Welcome

iPod Hi-Fi Rear View

Audio input port

AC power port

Battery compartment

Chapter 1 Welcome

11

 

 

2

Setting Up Your iPod Hi-Fi

2

 

 

 

 

You can set up and start listening to music on your iPod Hi-Fi in a few easy steps.

Step 1: Plug In Your iPod Hi-Fi or Insert Batteries

You can plug in your iPod Hi-Fi, or insert six D batteries to use it on the go.

Turn the latch with a coin to remove the battery

compartment cover.

To use your iPod Hi-Fi on the go, insert six

You can also plug your

D batteries. Position the positive (+) and

iPod Hi-Fi into an outlet using

negative (–) terminals on the batteries as shown.

the included power cord.

12

Step 2: Connect Your iPod

Choose the dock adapter that fits your iPod. Your iPod fits snugly into the correct adapter.

The number (411) shows which iPod fits

iPod

iPod with

iPod nano

iPod with

iPod nano

 

color display

 

video

(Second Generation)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4

6

8

9

11

20GB and

20GB, 30GB, and

1GB, 2GB, and

30GB

2GB, 4GB, and

U2 Special Edition

U2 Special Edition

4GB

 

8GB

5

7

 

10

 

40GB

40GB and 60GB

 

60GB and 80GB

 

Note: If there is no dock adapter for your model of iPod included with your iPod Hi-Fi, you can purchase one at www.apple.com/ipodstore. If you have an older iPod that doesn’t have a dock connector on the bottom, you can use an audio cable to connect it to the audio input port (see page 16).

Chapter 2 Setting Up Your iPod Hi-Fi

13

 

 

Insert the dock adapter into your iPod Hi-Fi and connect your iPod. The iPod Hi-Fi status light blinks green.

Dock adapter

Connector well

You can remove the dock adapter

with your fingernail by using this slot.

Step 3: Play Music

Browse for a song on iPod, then press Play (’) and enjoy! Use the buttons on your iPod Hi-Fi or on the included Apple Remote to increase or decrease the volume.

14 Chapter 2 Setting Up Your iPod Hi-Fi

Using Your iPod Hi-Fi

3

 

 

 

Read on to learn about connecting iPod to your iPod Hi-Fi, connecting other audio devices, adjusting the sound, using the Apple Remote, and more.

Connecting iPod

You can connect any iPod to your iPod Hi-Fi. If your iPod has a dock connector, you can insert it into your iPod Hi-Fi. If your iPod doesn’t have a dock connector, you can use an audio cable to connect it to the audio input port (see page 16).

To connect an iPod with a dock connector:

mInsert the dock adapter that fits your iPod, and then connect your iPod as shown on page 14. The status light blinks green.

Your iPod Hi-Fi includes dock adapters that work with most models of iPod with dock connectors. If you want to connect a different iPod, you can easily remove the dock adapter from your iPod Hi-Fi using a fingernail, insert the adapter that fits the other iPod, and then insert the other iPod.

If there is no dock adapter for your model of iPod included with your iPod Hi-Fi, you can purchase one at www.apple.com/ipodstore.

15

Changing iPod Screen Settings

With some newer iPod models, you can set how the backlight behaves when iPod is connected to your iPod Hi-Fi. You can also set whether you see the Now Playing screen or album artwork on iPod. You’re able to change these settings if you see a Speakers item in the main menu when you connect your iPod.

To set how the backlight behaves, choose Speakers and follow these instructions:

mTo set the backlight to be on when music is playing, set Backlight to While Playing.

Note: This is the default setting.

mTo set the backlight to turn on when you use the remote or the iPod controls, set Backlight to On Keypress.

mTo set the backlight to be on always, set Backlight to Always On.

mTo set the backlight to be off always, set Backlight to Always Off.

To set your iPod to display full screen album artwork (when artwork is available for that song):

mChoose Speakers and set Large Album Art to On.

Connecting Other Audio Devices or an iPod Without a Dock Connector

Your iPod Hi-Fi has a digital/analog audio input port. You can use it to play music from an iPod that doesn’t have a dock connector, or from other audio devices, such as a CD player, stereo receiver, or computer. If you have an AirPort Express Base Station, you can connect it to your iPod Hi-Fi and play music from a computer in another room.

16 Chapter 3 Using Your iPod Hi-Fi

You connect audio devices or an older iPod using an audio cable with a standard 3.5 millimeter stereo miniplug. For higher-quality sound, you can connect an optical digital audio device using an optical digital audio cable with a Mini-Toslink connector.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3.5mm Stereo Miniplug

Optical digital cable with Mini-Toslink connector

(available separately)

(available separately)

To play music from another audio device through your iPod Hi-Fi:

1Connect an audio cable to the audio input port on your iPod Hi-Fi and to a line-level port or headphones port on the device.

WARNING: Distortion may occur if you connect your iPod Hi-Fi to a device with an output higher than 2V (volts) RMS. Do not connect your iPod Hi-Fi to the speaker outputs from another device. You could damage your iPod Hi-Fi.

2Turn on the device and begin playing music from it.

See the documentation that came with the device for more information.

Chapter 3 Using Your iPod Hi-Fi

17

 

 

To switch playback from an iPod to a device connected to the audio input port:

If an iPod with a dock connector and an audio device are connected to your iPod Hi-Fi at the same time, your iPod Hi-Fi plays music from the iPod by default.

mPress and hold the Menu button on the remote. The status light blinks green, and the iPod pauses. To switch back to the iPod, press and hold the Menu button again.

You can also remove your iPod to switch to a device connected to the audio input port.

To play audio from your computer using your iPod Hi-Fi:

mYou can connect an AirPort Express Base Station to your iPod Hi-Fi and stream audio wirelessly from a computer in another room.

For more information, go to www.apple.com/airportexpress.

mIn most cases, you can also connect a computer directly to your iPod Hi-Fi using an audio cable. If you have a computer with optical digital audio, such as a Mac Pro or a MacBook Pro, you can connect it using an optical digital cable for better quality sound.

Adjusting the Sound

To adjust the volume:

mPress the Volume Up (∂ ) or Volume Down (D) button on top of your iPod Hi-Fi or on the included remote.

With some newer models of iPod, you can also adjust the volume using the iPod Click Wheel.

18 Chapter 3 Using Your iPod Hi-Fi

If you connect another audio device that has volume controls to the audio input port, such as a stereo receiver, you can also change the volume using the other device. Experiment to see which volume level sounds best when using the device with your iPod Hi-Fi.

To change equalizer settings:

mIf you’re playing music through an iPod, change the settings on the iPod. Choose Settings > EQ and choose an equalizer preset.

mIf you’re playing music through a device connected to the audio input port, change equalizer settings on the device, if possible. See the documentation that came with the device.

To increase the bass or the treble:

With some newer models of iPod, you can also set your iPod Hi-Fi to increase the bass or the treble. You’re able to adjust this setting if you see a Speakers item in the main menu when you connect your iPod.

mChoose Speakers > Tone Control, and then choose Treble Boost, Normal, or Bass Boost.

Chapter 3 Using Your iPod Hi-Fi

19

 

 

Using the Apple Remote

You can use the included infrared remote to control playback. Make sure there are no obstructions between the remote and your iPod Hi-Fi.

Using the Remote with iPod

To use the remote when playing music from an iPod connected to your iPod Hi-Fi, follow the instructions below.

To

Do This

Play or pause a song

Press the Play/Pause () button.

 

 

Change the volume

Press the Volume Up () or Volume Down (D)

 

button.

 

 

Skip to the next song

Press the Next/Fast-forward () button.

 

 

Restart a song or play the previous song

Press the Previous/Rewind (]) button once to

 

restart a song. Press it twice to play the previous

 

song.

 

 

Fast-forward or rewind a song

Press and hold the Next/Fast-forward () or

 

Previous/Rewind (]) button.

 

 

Switch to a device connected to the audio

Press and hold the Menu button (or remove iPod).

input port

 

 

 

Note: You can’t use the remote to skip to a different playlist. You must use the iPod controls to choose another playlist.

20 Chapter 3 Using Your iPod Hi-Fi

Using the Remote With Another Audio Device

To use the remote when playing music from a device connected to the audio input port, follow the instructions below.

To

Do This

Change the volume

Press the Volume Up () or Volume Down (D)

 

button. (You can also use the volume controls on

 

the audio device.)

 

 

Mute or unmute the sound

Press the Play/Pause () button.

 

 

Switch to an iPod connected to your

Press and hold the Menu button.

iPod Hi-Fi

 

 

 

Changing the Battery

The remote includes a battery. When needed, you can replace it with a CR2032 battery.

Press this button with a small blunt object, such as a paper clip, to partially eject the battery compartment.

Pull the battery compartment free from the remote. Replace the battery, making sure the positive (+) side faces up.

Chapter 3 Using Your iPod Hi-Fi

21

 

 

Pairing Your iPod Hi-Fi with the Remote

The included Apple Remote works with other compatible Apple products that have a built-in infrared (IR) receiver. You can set your iPod Hi-Fi to work only with the included remote so that remotes for your other devices don’t affect your iPod Hi-Fi.

You may wish to pair your other Apple Remote–compatible devices with other Apple Remotes so that the remote you use with your iPod Hi-Fi doesn’t affect those devices. See the documentation that came with the other devices for instructions.

To set your iPod Hi-Fi to work only with the included remote:

1Connect your iPod Hi-Fi to an electrical outlet.

Note: If your iPod Hi-Fi has batteries, you don’t need to connect it to an outlet.

2Make sure other products that are compatible with the remote are not in range, and hold the remote close to your iPod Hi-Fi (about 3 to 4 inches away).

3Press and hold the Menu and Next/Fast-forward (‘) buttons on the remote simultaneously for about six seconds. The status light blinks green several times.

Your iPod Hi-Fi now works only with the paired remote.

To reset your iPod Hi-Fi to work with all Apple Remotes:

mFollow steps 1 and 2 above. Then press and hold the Menu and Previous/Rewind (]) buttons on the remote simultaneously for about six seconds. The status light blinks green several times.

Your iPod Hi-Fi now works with all Apple Remotes.

22 Chapter 3 Using Your iPod Hi-Fi

Saving Battery Life

When not in use, your iPod Hi-Fi enters a low-power standby mode to save battery life.

However, if you don’t plan to use your iPod Hi-Fi for an extended period, you may wish to remove the batteries to extend battery life even longer. For information on changing the batteries, see page 12.

Note: If you are using your iPod Hi-Fi with batteries (and not plugged into an electrical outlet) and you connect an iPod with a dock connector, the batteries in your iPod Hi-Fi will provide a minimum charge to iPod. If you don’t want the batteries in your

iPod Hi-Fi to expend power when iPod isn’t playing, remove iPod from your iPod Hi-Fi. If your iPod Hi-Fi is plugged into an electrical outlet, the iPod battery charges until it is fully charged.

Chapter 3 Using Your iPod Hi-Fi

23

 

 

4

Tips and Troubleshooting

4

 

 

 

 

Most problems with your iPod Hi-Fi can be solved quickly by following the advice in this chapter.

If your iPod Hi-Fi won’t play music or respond

ÂMake sure the volume isn’t turned down all the way. If another audio device is connected, make sure the volume on that device isn’t turned down all the way.

ÂUnplug your iPod Hi-Fi, wait about five seconds, and plug it in again. Make sure the power cord connectors on both ends of the power cord are pushed in all the way.

ÂIf you’re using batteries, make sure the batteries are inserted correctly.

ÂIf an iPod and another audio device are connected, make sure your iPod Hi-Fi is set to play from the device you want (see page 18).

ÂThe batteries may need to be replaced (see page 12).

If your iPod won’t respond

ÂMake sure the Hold switch is off and your iPod is not paused.

ÂReset your iPod. Connect iPod to your iPod Hi-Fi, set the Hold switch to HOLD, and then turn it off again. Then press and hold the Center and Menu buttons for about six seconds, until the Apple logo appears.

Note: If you have an original iPod with a dock connector (with four buttons below the display), press and hold the Play/Pause (’) and Menu buttons to reset it.

24

ÂIf that doesn’t work, see the documentation that came with your iPod for more information.

If the remote isn’t working

ÂMake sure to point the remote directly at your iPod Hi-Fi.

ÂMake sure the remote sensor on the front panel of your iPod Hi-Fi (see page 10) is not blocked.

ÂMake sure you can play music through your iPod Hi-Fi using the iPod controls. The problem may not be with the remote.

ÂThe remote battery may need to be replaced (see page 21).

ÂIf you have more than one Apple Remote and you have paired your iPod Hi-Fi with one of them, make sure you’re using the right remote. For instructions on setting your iPod Hi-Fi to work with any Apple Remote, see page 22.

If your iPod Hi-Fi isn’t playing music from another device

ÂMake sure the volume on the device and on your iPod Hi-Fi isn’t turned down all the way.

ÂIf an iPod is connected to your iPod Hi-Fi, disconnect it, or press and hold the Menu button on the remote until the status light blinks green.

ÂMake sure you’re using the correct audio cable (see page 16) and that it is connected firmly to your iPod Hi-Fi and to the device.

ÂMake sure the device is turned on and functioning correctly. See the documentation that came with the device for more information.

Chapter 4 Tips and Troubleshooting

25

 

 

5 Learning More, Service,

5

and Support

You can find more information about using your iPod Hi-Fi on the web.

Safety and Regulatory Compliance

For important safety and regulatory compliance information, see the included iPod Hi-Fi Safety and Regulatory Compliance Information booklet.

Online Resources

For the latest information about the iPod Hi-Fi, go to www.apple.com/ipodhifi.

For service and support information, go to www.apple.com/support/ipodhifi.

For an online iPod tutorial, iPod service and support information, and the latest Apple software downloads, go to www.apple.com/support/ipod.

To register your iPod Hi-Fi, go to www.apple.com/register.

26

Obtaining Warranty Service

If the product appears to be damaged or does not function properly, please follow the advice in this booklet, in the included iPod Hi-Fi safety booklet, and the online resources.

If the unit still does not function, go to www.apple.com/support/ipodhifi for instructions on how to obtain warranty service.

Finding the Serial Number of Your iPod Hi-Fi

The serial number is printed on the inside of the battery compartment of your iPod Hi-Fi.

Chapter 5 Learning More, Service, and Support

27

 

 

Loading...
+ 74 hidden pages