ANPEC APL1117-VC-TU, APL1117-VC-TR, APL1117-UC-TU, APL1117-UC-TR, APL1117-33FC-TR Datasheet

...
0 (0)

APL1117

1A Low Dropout Fast Response Positive Adjustable Regulator and Fixed 1.8V, 2.5V, 2.85V and 3.3V

Features

Guaranteed Output Voltage Accuracy within 2%

Fast Transient Response

Guaranteed Dropout Voltage at Multiple Currents

Load Regulation : 0.1% Typ.

Line Regulation : 0.03% Typ.

Low Dropout Voltage : 1.1V Typ. at IOUT =1A

Current Limit : 1A Typ. at TJ=25° C

On-Chip Thermal Limiting : 150° C Typ.

Adjustable Output : 1.25~10.7V

Standard 3-pin TO-220, TO-252, TO-263 and SOT-223 Power Packages

General Description

The APL1117 is a low dropout three-terminal adjustable regulators with 1A output current capability. In order to obtain lower dropout voltage and faster transient response, which is critical for low voltage applications , the APL1117 has been optimized. The device is available in an adjustable version and fixed output voltages of 1.8V, 2.5V, 2.85V and 3.3V. The output available voltage range of an adjustable version is from 1.25~10.7V with an input supply below 12V. Dropout voltage is guaranteed at a maximum of 1.3V at 1A. Current limit is trimmed to ensure specified output current and controlled short-circuit current. On-chip thermal limiting provides protection against any combination of overload that would create excessive junction temperatures. The APL1117 is available in the industry standard 3-pin TO-220, TO-252, TO263, and the low profile surface mount SOT-223 power packages which can be used in applications where space is limited.

Applications

Pin Description

 

Active SCSI Terminators

 

 

Front View for TO-220

 

Low Voltage Logic Supplies

 

 

 

 

 

 

3

 

VIN

 

 

 

 

 

 

Battery-Powered Circuitry

 

 

2

 

VOUT

 

 

 

 

 

 

Post Regulator for Switching Power Supply

 

 

1

 

ADJ/GND

 

 

 

 

 

 

Front View for TO-263

 

 

3

 

 

VIN

 

 

 

 

TAB is V

OUT

2

 

 

VOUT

 

 

 

 

 

 

1

 

 

ADJ/GND

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Front View for TO-252

 

3

VIN

TAB IS VOUT

2

V

 

 

OUT

 

1

ADJ/GND

 

 

ANPEC reserves the right to make changes to improve reliability or manufacturability without notice, and advise customers to obtain the latest version of relevant information to verify before placing orders.

Copyright ANPEC Electronics Corp.

1

www.anpec.com.tw

Rev. B.8 - Jun., 2003

 

 

APL1117

Pin Description (Cont.)

Front View for SOT-223

T A B IS V O U T

 

3

IN

 

2

O U T

 

1

A D J /G N D

Ordering and Marking Information

A P L 1 1 1 7 -

 

 

 

 

 

 

 

 

 

 

 

 

P a c k a g e C o d e

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

F : T O -2 2 0

G : T O -2 6 3

U : T O -2 5 2

V : S O T -2 2 3

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

H a n d lin g C o d e

T e m p . R a n g e

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

C : 0 to 7 0 ° C

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

T e m p . R a n g e

H a n d lin g C o d e

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

T U : T u b e

T R : T a p e & R e e l

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

P a c k a g e C o d e

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

V o lta g e C o d e

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

V o lta g e C o d e

1 8 : 1 .8 V

2 5 : 2 .5 V

2 8 : 2 .8 5 V

3 3 : 3 .3 V

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

B la n k : A d ju s ta b le V e rs io n

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

A P L 1 1 1 7 F /G /U :

 

 

 

 

 

 

 

 

 

 

X X X X X - D a te C o d e

A P L 1 1 1 7 V :

 

A P L 1 1 1 7

X X X X X - D a te C o d e

 

A P L 1 1 1 7

 

 

X X X X X

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

X X X X X

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

A P L 1 1 1 7 -1 8 F /G /U :

 

1 8

 

X X X X X - D a te C o d e

A P L 1 1 1 7 -1 8 V :

 

A P L 1 1 1 7

X X X X X - D a te C o d e

 

A P L 1 1 1 7

 

 

X X X X X 1 8

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

X X X X X

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2 5

 

 

 

 

 

 

 

 

 

A P L 1 1 1 7 -2 5 F /G /U :

 

 

X X X X X - D a te C o d e

A P L 1 1 1 7 -2 5 V :

 

A P L 1 1 1 7

X X X X X - D a te C o d e

A P L 1 1 1 7

 

 

 

 

X X X X X 2 5

 

 

 

 

 

 

X X X X X

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2 8

 

 

 

 

 

 

 

 

 

A P L 1 1 1 7 -2 8 F /G /U :

 

 

 

X X X X X - D a te C o d e

A P L 1 1 1 7 -2 8 V :

 

A P L 1 1 1 7

X X X X X - D a te C o d e

 

 

 

 

 

 

 

 

 

 

 

 

 

A P L 1 1 1 7

 

 

X X X X X 2 8

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

X X X X X

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3 3

 

 

 

 

 

 

 

 

 

A P L 1 1 1 7 -3 3 F /G /U :

 

 

X X X X X - D a te C o d e

A P L 1 1 1 7 -3 3 V :

 

A P L 1 1 1 7

X X X X X - D a te C o d e

A P L 1 1 1 7

 

 

 

 

X X X X X 3 3

 

 

 

 

 

 

X X X X X

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Absolute Maximum Ratings

Symbol

 

Parameter

Rating(Note)

 

Unit

VI

Input Voltage

APL1117, APL1117-33

15

 

V

 

APL1117-18, APL1117-25, APL1117-28

9

 

 

 

 

 

 

 

TJ

Operating Junction Temperature Range

 

 

° C

 

 

Control Section

0 to 125

 

 

 

 

Power Transistor

0 to 150

 

 

TSTG

Storage Temperature Range

-65 to +150

 

° C

TL

Lead Temperature (Soldering, 10 second)

260

 

° C

Note : The values here show the absolute maximum rating, and for normal usage please refer the test condition in Electrical

Characteristics Table.

 

 

 

 

 

 

 

 

 

 

Copyright ANPEC Electronics Corp.

2

 

www.anpec.com.tw

Rev. B.8 - Jun., 2003

 

 

 

 

APL1117

Electrical Characteristics (Cont.)

 

Symbol

Parameter

 

Test Conditions

APL1117

Unit

 

 

 

 

 

 

 

 

 

 

Min.

Typ.

Max.

 

 

VREF

Reference Voltage

10mA

IOUT 1A, 1.4V(VIN -VOUT) 10.75V,

1.225

1.250

1.275

V

 

 

 

 

TJ =0~125° C

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

VOUT

Output Voltage

 

 

 

 

 

 

 

 

 

 

 

 

 

APL1117-18

TJ =0~125° C,

 

 

 

 

 

 

 

 

 

 

 

0IOUT

1.5A, 3.5VVIN9V,

1.764

1.800

1.836

 

 

 

 

APL1117-25

TJ =0~125° C,

 

 

 

 

 

 

 

 

 

 

 

0IOUT

1A, 4VVIN9V,

2.450

2.500

2.550

V

 

 

 

APL1117-28

TJ =0~125° C,

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

0IOUT

1A, 4.25VVIN9V,

2.790

2.850

2.910

 

 

 

 

APL1117-33

TJ =0~125° C,

 

 

 

 

 

 

 

 

 

 

 

0IOUT

1A, 4.75V

 

VIN12V,

3.235

3.300

3.365

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

REGLINE

Line Regulation

IOUT=10mA, 1.5V(VIN -VOUT )10.75V (Note1)

 

 

 

 

 

 

 

APL1117

 

0.03

0.2

%

 

 

 

APL1117-18

IOUT=0A, 3.5VVIN9V (Note1)

 

1

6

mV

 

 

 

APL1117-25

IOUT=0A, 4VVIN5.5V (Note1)

 

1

6

 

 

 

 

APL1117-28

IOUT=0A, 4.25V

VIN

5.15V (Note1)

 

1

6

 

 

 

 

APL1117-33

IOUT=0A, 4.75V

VIN

7.75V (Note1)

 

1

6

 

 

REGLOAD

Load Regulation

(VIN -VOUT)=3V, 0IOUT 1A (Note1)

 

 

 

 

 

 

 

APL1117

 

0.1

0.4

%

 

 

 

APL1117-18

VIN=3.5V, 0

IOUT 1A (Note1)

 

1

10

mV

 

 

 

APL1117-25

VIN =4V, 0IOUT 1A (Note1)

 

1

10

 

 

 

 

APL1117-28

VIN=4.25V, 0

IOUT

1A (Note1)

 

1

10

 

 

 

 

APL1117-33

VIN=4.75V, 0

IOUT

1A (Note1)

 

1

10

 

 

VD

Dropout Voltage

IOUT=100mA (Note2)

 

 

 

1

1.1

 

 

 

 

 

IOUT=500mA (Note2)

 

 

 

1.05

1.2

V

 

 

 

 

IOUT=1A (Note2)

 

 

 

 

 

1.1

1.3

 

 

ILIMIT

Current Limit

(VIN -VOUT)=5V, TJ=25° C

1000

 

 

mA

 

IADJ

Adjust Pin Current

(VIN -VOUT)=3V, IOUT=10mA

 

60

120

A

 

 

 

APL1117

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

IADJ

Adjust

Pin Current

10mA

IOUT 1A,

 

 

 

0.2

5

A

 

 

Change APL1117

1.4V(VIN -VOUT) 10.75V

 

 

 

 

 

IO

Minimum Load

(VIN -VOUT)=10.75V (Note3)

 

1.7

 

mA

 

 

Current

APL1117

 

 

 

 

 

 

 

 

 

 

 

PSRR

Ripple Rejection

fRIPPLE=120Hz, VRIPPLE=1VP-P,

60

75

 

dB

 

 

 

 

(VIN -VOUT)=3V

 

 

 

 

 

 

 

 

TR

Thermal Regulation

TJ=25° C, 30ms Pulse

 

0.01

0.02

%/ W

 

TS

Temperature

 

 

 

 

 

 

 

0.5

 

%

 

 

Stability

 

 

 

 

 

 

 

 

 

 

 

LS

Long -Term

TJ =125° C,1000Hrs.

 

0.3

 

%

 

 

Stability

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Copyright ANPEC Electronics Corp.

 

 

3

 

 

www.anpec.com.tw

Rev. B.8 - Jun., 2003

 

 

 

 

 

 

 

 

 

 

 

APL1117

Electrical Characteristics (Cont.)

Symbol

Parameter

Test Conditions

APL1117

 

Unit

Min.

Typ.

Max.

VN

RMS Output Noise

TJ=25° C,10Hz≤ F≤ 10kHz, (% of VOUT)

 

0.003

 

 

%

 

 

 

 

 

 

 

 

θ th

Thermal Resistance

Junction to Case, at Tab

 

15

 

 

° C/ W

 

 

Junction to Ambient

 

50

 

 

 

OT

Over Temperature

 

 

150

 

 

° C

 

Point

 

 

 

 

 

 

IQ

Quiescent Current

 

 

 

 

 

 

 

APL1117-18

VIN≤ 9V

 

5.5

 

10

mA

 

APL1117-25

VIN≤ 9V

 

5.5

 

10

 

 

APL1117-28

VIN≤ 9V

 

5.5

 

10

 

 

APL1117-33

VIN≤ 12V

 

5.5

 

10

 

Note 1 : See thermal regulation specifications for changes in output voltage due to heating effects. Load line regulations are measured at a constant junction temperature by low duty cycle pulse testing.

Note 2 : Dropout voltage is specified over the full output current range of the device. Dropout voltage is defined as the minimum input/output differential measured at the specified output current. Test points and limits are also shown on the Dropout Voltage curve.

Note 3 : Minimum load current is defined as the minimum output current required to maintain regulation.

Copyright ANPEC Electronics Corp.

4

www.anpec.com.tw

Rev. B.8 - Jun., 2003

 

 

APL1117

Application Circuits

1.25V to 10.7V Adjustable Regulator

 

 

APL1117

 

 

 

 

VIN

 

IN

OUT

 

 

V

 

 

 

 

R1

 

 

OUT1

 

 

ADJ

 

 

 

 

 

 

 

 

 

 

 

 

 

121Ω

 

 

 

+ 10µ

F

 

 

+ 100µ

F

 

C1*

R2

 

 

C2

 

 

 

 

1k

 

 

 

 

* Needed if device is far from filter capacitors

 

 

 

VOUT = 1.250V X R1 + R2

 

 

 

 

 

 

 

R1

 

 

 

5V Regulator with Shutdown

 

 

 

 

APL1117

 

 

 

VIN

 

IN

 

OUT

121Ω

5V

+

 

 

ADJ

 

 

10µ

F

 

 

1%

 

 

 

 

 

+

 

 

 

 

1k

 

 

100µ

F

TTL

 

 

 

365Ω

 

 

 

 

 

 

 

 

1k

 

1%

 

 

 

 

 

 

 

 

Improving Ripple Rejection

 

 

 

 

 

 

 

 

 

 

 

APL1117

 

 

 

 

 

 

 

 

 

 

 

VIN

 

 

 

 

 

 

 

 

 

 

IN

 

OUT

 

 

 

 

 

 

 

 

V

 

 

+

 

 

 

 

 

 

R1

 

 

 

OUT

 

 

 

 

 

 

 

 

 

ADJ

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

121

 

 

 

 

 

 

 

1 0 µ

F

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1%

 

 

 

 

150µ F

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

R2

 

+

 

 

C1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

365

 

 

 

 

1 0 µ

F

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1%

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

* C1 improves ripple rejection. XC should be approximately equal to R1 at ripple frequency

Copyright ANPEC Electronics Corp.

5

www.anpec.com.tw

Rev. B.8 - Jun., 2003

 

 

ANPEC APL1117-VC-TU, APL1117-VC-TR, APL1117-UC-TU, APL1117-UC-TR, APL1117-33FC-TR Datasheet

APL1117

Typical Characteristics

Load Transietn Response

Line Transient Response

 

5

 

 

 

 

APL1117-33

0.02

 

6

 

 

 

 

 

 

 

 

 

 

 

4.5

 

 

 

 

 

 

 

 

 

 

4

 

 

 

 

 

 

0.01

 

5

Output Current (A)

3.5

 

 

 

 

 

 

 

Input Voltage (V)

4

3

 

 

 

 

 

 

0

 

 

 

 

 

 

 

2.5

CIN=10 F

 

 

 

 

 

3

 

 

 

 

 

 

2

 

 

 

 

-0.01

 

COUT=10

F Tantalum

 

 

 

1.5

VIN=5V

 

 

 

 

 

2

 

 

 

 

 

 

 

1

 

 

 

 

 

 

-0.02

 

 

 

 

 

 

 

 

 

1

 

0.5

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

0

 

 

 

 

 

 

-0.03

 

0

 

-100

100

300

500

700

900

 

 

 

 

 

 

APL1117-33

0.15

 

 

 

 

 

0.1

 

CIN=10 F

 

 

 

 

 

COUT=10

F Tantalum

 

 

 

 

IOUT=0.1A

 

 

0.05

 

 

 

 

 

0

 

 

 

 

 

-0.05

-20

30

80

130

180

Time ( S)

Time ( S)

Dropout Voltage vs. Output Current

 

1.25

 

 

 

 

APL1117-33

 

 

 

 

 

 

 

1.2

 

 

 

 

 

(V)

1.15

 

 

 

 

 

Voltage

1.1

 

 

 

 

 

 

 

 

 

 

 

Dropout

1.05

 

 

 

 

 

1

 

 

 

 

 

 

 

 

 

 

 

 

0.95

 

 

 

 

 

 

0.9

 

 

 

 

 

 

0

0.2

0.4

0.6

0.8

1

Output Voltage vs. Input Voltage

 

3.5

 

 

 

 

 

 

 

 

 

 

3

 

 

 

 

 

 

 

 

 

(V)

2.5

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Voltage

2

 

 

 

 

 

 

 

 

 

1.5

 

 

 

 

 

 

 

 

 

Output

 

 

 

 

 

 

 

 

 

1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

0.5

 

 

 

 

 

 

 

 

 

 

0

 

 

 

 

 

 

 

 

 

 

0

1

2

3

4

5

6

7

8

9

Output Current (A)

Input Voltage (V)

Copyright ANPEC Electronics Corp.

6

www.anpec.com.tw

Rev. B.8 - Jun., 2003

 

 

Loading...
+ 12 hidden pages