Loading...
instruction manual
UPC20+
Universal Power Controller
Control System Accessories
AMX Limited Warranty and Disclaimer
AMX Corporation warrants its products to be free of defects in material and workmanship under normal use for three (3) years from the date of purchase from AMX Corporation, with the following exceptions:
•Electroluminescent and LCD Control Panels are warranted for three (3) years, except for the display and touch overlay components that are warranted for a period of one (1) year.
•Disk drive mechanisms, pan/tilt heads, power supplies, MX Series products, and KC Series products are warranted for a period of one (1) year.
•Unless otherwise specified, OEM and custom products are warranted for a period of one (1) year.
•Software is warranted for a period of ninety (90) days.
•Batteries and incandescent lamps are not covered under the warranty.
This warranty extends only to products purchased directly from AMX Corporation or an Authorized AMX Dealer.
AMX Corporation is not liable for any damages caused by its products or for the failure of its products to perform. This includes any lost profits, lost savings, incidental damages, or consequential damages. AMX Corporation is not liable for any claim made by a third party or by an AMX Dealer for a third party.
This limitation of liability applies whether damages are sought, or a claim is made, under this warranty or as a tort claim (including negligence and strict product liability), a contract claim, or any other claim. This limitation of liability cannot be waived or amended by any person. This limitation of liability will be effective even if AMX Corporation or an authorized representative of AMX Corporation has been advised of the possibility of any such damages. This limitation of liability, however, will not apply to claims for personal injury.
Some states do not allow a limitation of how long an implied warranty last. Some states do not allow the limitation or exclusion of incidental or consequential damages for consumer products. In such states, the limitation or exclusion of the Limited Warranty may not apply. This Limited Warranty gives the owner specific legal rights. The owner may also have other rights that vary from state to state. The owner is advised to consult applicable state laws for full determination of rights.
EXCEPT AS EXPRESSLY SET FORTH IN THIS WARRANTY, AMX CORPORATION MAKES NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. AMX CORPORATION EXPRESSLY DISCLAIMS ALL WARRANTIES NOT STATED IN THIS LIMITED WARRANTY. ANY IMPLIED WARRANTIES THAT MAY BE IMPOSED BY LAW ARE LIMITED TO THE TERMS OF THIS LIMITED WARRANTY.
UPC20+ Wiring Requirements
In the United States, the UPC20+ must be wired by an authorized electrician in
!accordance with the National Electrical Code, ANSI/NFPA 70-1987, as well as all local codes.
In the European community, the UPC20+ unit must be wired by an authorized elec-
!trician in accordance with all applicable European codes.
A readily accessible disconnect device shall be incorporated into the fixed wiring.
An insulated earthing conductor that is identical in size, insulation material and thickness to be earthed and unearthed branch circuit supply conductors, except that it is green with or without one or more yellow stripes, is to be installed as part of the branch circuit which supplies the unit or system. The earthing conductor described is to be connected to earth at the service equipment, or supplied by a separately derived system, at the supply transformer or motor generator set.
|
Table of Contents |
Table of Contents |
|
UPC20+ Wiring Requirements ................................................................................. |
3 |
Product Information ................................................................................................. |
1 |
Specifications .................................................................................................................. |
3 |
Control Options Modes...................................................................................................... |
5 |
Motor Control mode ............................................................................................................. |
.... 5 |
Power Control mode ............................................................................................................. |
... 6 |
Remote Sensor Control mode.................................................................................................. |
6 |
Channel codes (Remote Sensor mode)................................................................................... |
7 |
Installation ................................................................................................................. |
9 |
P1 Terminal Connections .................................................................................................. |
9 |
P2 Terminal Connections .................................................................................................. |
9 |
Control Mode................................................................................................................... |
10 |
High Voltage Wiring Options ........................................................................................... |
12 |
Single circuit 120/240 VAC .................................................................................................... |
12 |
Dual circuit 120/240 VAC ....................................................................................................... |
12 |
Dual circuit 277 VAC ........................................................................................................... |
... 13 |
Wiring The UPC20+ to Either The IRX-DM+ Or IRX-SM+ .............................................. |
13 |
Wireless IR Sensor Connection ...................................................................................... |
13 |
Installing the UPC20+ ..................................................................................................... |
14 |
UPC20+ Universal Power Controller |
i |
|
|
|
|
Table of Contents
|
ii |
UPC20+ Universal Power Controller |
|
|
|
Product Information
Product Information
The UPC20+ Universal Power Control is a dual 20 Amp AC power and motor controller designed for conduit installation. The UPC20+ is housed in a compact metal wall-mount enclosure and is configurable for a wide variety of power and motor control modes. Low voltage contact-closures, open collector inputs or serial data from an AMX IR receiver enable control by simple wall panels, remote systems, or hand-held transmitters. A test switch with an LED indicator for each relay is provided for local control and status indication.
Using Motor Control mode, the UPC20+ output alternates between two relays, providing a brief pause in-between relay contacts, to protect the motor. A timing adjustment potentiometer is user adjustable for automatic release of the relays. (The range is 0 to 90 seconds). 1-, 2-, and 3- button control modes are selectable.
In Power Control mode, the UPC20+ provides power control for two independent circuits with a combined total load of 20 Amps. Single-button momentary/latching and 2-button latching modes are selectable.
Momentary Power Relay contacts are closed only as long as a closure from input to common is maintained.
Latching Power Relay contacts are toggled (from open to closed and closed to open) each time a closure from input to common is momentarily pulsed.
All functions and capabilities of the UPC20+ (including information on high voltage wiring, low voltage wiring, and DIP switch settings) are described on a sticker installed inside the enclosure. FIG. 1 shows the UPC20+ (inside view).
The UPC20+ will work the NXC-I/O10 input/output control card.
UPC20+ Universal Power Controller |
1 |
|
|
|
|
Loading...