BARRIER FREE
TOWN SQUARE® COUNTERTOP SINK
FIRECLAY
TOWN SQUARE® COUNTERTOP SINK
•American classic design
•Clean, straight lines with classic ogee curves
•Tapered interior bowl with flat bottom design provides dramatic look
•Made from fine fireclay
•Self-rimming with cutout template supplied
•Front overflow
0700.004 Faucet holes on 4" (203mm) centers (illustrated)
0700.008 Faucet holes on 8" (102mm) centers
0700.001 Center hole only
Nominal Dimensions:
23-1/8" x 18-3/4"
(587 x 476mm)
Bowl sizes:
18-1/2" (470mm) wide
10-1/2" (267mm) front to back
6-1/4" (159mm) deep
Compliance Certifications -
Meets or Exceeds the Following Specifications:
•ASME A112.19.9M for Non-Vitreous Ceramic Fixtures
•CAN/CSA B45 series
To Be Specified:
Color: White Bone Linen Black
Town Square Faucet:
Centerset Sink Faucet: 2555.201 (shown)
Widespread Sink Faucet: 2555.801
Other Sink Faucet*:
Faucet Finish:
Supplies:
1-1/4" Trap:
* See faucet section for additional models available
FINISHED WALL |
|
|
|
OR SPLASHBACK |
4" |
2-7/8" |
OPTIONAL |
|
(102mm) |
(73mm) |
|
9-3/4" |
|
|
|
(248mm) |
|
|
|
|
|
|
18-3/4" |
|
|
|
(476mm) |
1-3/4" DIA. |
|
|
|
STD. DRAIN |
|
|
|
OUTLET |
|
|
|
SEALING |
|
23-1/8" |
|
COMPOUND |
|
(587mm) |
1" |
COUNTERTOP |
|
|
(25mm) |
(BY OTHERS) |
|
|
|
|
|
|
8-1/8" |
*10-3/4" |
|
|
(206mm) |
(273mm) |
|
|
|
*12-7/8" (327mm)
|
|
|
|
|
|
|
|
|
|
SUPPLIES |
|
|
|
|
|
|
|
|
|
|
|
AS REQ'D |
31" |
8" |
|
|
|
|
|
|
|
||||
|
|
|
|
|
|
|
(787mm) |
||||
(203mm) |
|
|
|
|
|
||||||
|
|
|
|
|
SUGGESTED |
||||||
|
|
|
|
|
|
|
|
1-1/4" O.D. WASTE |
|||
|
|
|
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
1-1/4" O.D. TAILPIECE |
|
||
|
|
|
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
FINISHED FLOOR
NOTES:
* DIMENSIONS SHOWN FOR LOCATION OF SUPPLIES AND “P" TRAP ARE SUGGESTED.
FOR COUNTERTOP CUTOUT AND INSTALLATION INSTRUCTIONS USE TEMPLATE SUPPLIED WITH SINK.
FITTINGS NOT INCLUDED WITH FIXTURE AND MUST BE ORDERED SEPARATELY.
SEALING COMPOUND SUPPLIED BY OTHERS.
IMPORTANT: Dimensions of fixtures are nominal and may vary within the range of tolerances established by ANSI Standard A112.19.9M.
These measurements are subject to change or cancellation. No responsibility is assumed for use of superseded or voided pages.
|
J27 |
|
|
© 2008 AS America Inc. |
Revised 2/08 |
||
|