Product No.'s & Options |
1 |
Specifications |
2 |
How to Install |
2-3 |
Maintenance |
3-7 |
FAQ,s |
7-8 |
Replacement Parts |
8 |
Certified to comply with ASME A112.18.1M
© 2012 American Standard
1. Remove the fitting and loose items from the carton.The illustration below shows the fitting and all loose items after they have been removed from the carton. Some items may be packaged partially assembled to other items.
3a. AC Power Supply (7056 Series)
|
6 |
|||
DO NOT REMOVE |
|
|
|
DO NOT REMOVE |
PROTECTIVE |
|
|
|
PROTECTIVE FILM |
FROM SENSOR |
|
|
|
FROM SENSOR EYE |
UNTIL INSTALLATION |
|
|
|
UNTIL INSTALLATION |
IS COMPLETE |
|
|
|
IS COMPLETE. |
3 |
3 |
|||
|
|
|
|
|
|
|
|
|
|
|
3a |
|
3a |
7 |
8 |
7 |
8 |
|
|
||
© 2012 American Standard |
|
© 2012 American Standard |
|
2
705P400
4
1 |
M965255 REV. 1.6 |
|
Roughing-in Dimensions
Fig. 1
FINISHED WALL
OR BACKSPLASH
MIN. 1" CLEARANCE
38mm (1-1/2 )
457mm
(18)
3/8" COMPRESSION CONNECTORS
MOUNTING
SURFACE
32mm (1-1/4)
GENERAL DESCRIPTION:
Electronic faucet with proximity operation. Vandal resistant solid brass construction single post mounting. Operates on DC (battery) or AC power. Inlets 3/8" compression, built-in checks, flexible stainless steel 18" reach inlet hoses for spout connection and In-line integral strainer for solenoid.
TOOLS REQUIRED; Fig. 2
1 |
Hex Wrench (Included) |
4 |
Phillips Screwdriver |
2 |
Adjustable Wrench |
5 |
Tape Measure |
3 |
Plumbers' Putty or Caulking |
|
|
INSTALLATION
1 INSTALL SPOUT ASSEMBLY;
Fig. 1 CAUTION Turn off hot and cold water supplies before beginning
1.Make sure O-RING SEAL (9) is installed.
2.Installation with ESCUTCHEON (1) (optional).Apply a bead of putty to bottom edge of ESCUTCHEON with PUTTY PLATE (1). (Only if mounting surface is uneven).
3.Insert supply HOSES (2), SHANK (3) and POWER CORD
(10)(if equipped) through hole in ESCUTCHEON with PUTTY PLATE (1) and mounting surface. Follow mounting instructions below to secure faucet to mounting surface.
(Make sure PIN (7) is in back).
4.Installation less ESCUTCHEON (1). IMPORTANT: Do not use putty when installing faucet without escutcheon.
5.Assemble RUBBER WASHER (4), BRASS WASHER
(5)and THREADED LOCKNUT (6) onto SHANK (3) from underside of sink or mounting surface. Hand tighten LOCKNUT (6).
6.Use a screwdriver to tighten SCREWS (8) on LOCKNUT (6). Work your way around LOCKNUT (6), tightening the screws slightly each time until all are snug to ensure even pressure.
2 CONNECT POWER SUPPLY; Fig. 1a
(7056 series only)
1.Connect the sensor cable (1) to the POWER SUPPLY CABLE (2).
2.Code approved Electrical Outlet provided by others. (120V 50/60 Hz)
3.Plug AC POWER SUPPLY (3) into Outlet.
Fig. 2
3 |
|
2 |
|
|
4 |
5 |
10' |
||
|
Fig. 1
IMPORTANT: Do not |
|
|
|
use putty when installing |
|
|
|
faucet without escutcheon. |
7 |
||
PUTTY |
9 |
||
(If required) |
|
|
|
|
|
|
|
|
3 |
|
1 (OPTIONAL) |
|
10 |
|
MOUNTING |
|
|
||
|
|
SURFACE |
|
|
2 |
|
TIGHTEN |
|
|
|
SPIN NUTS |
4 58
6
2 |
M965255 REV. 1.6 |
|