REMINISCENCE™
PEDESTAL SINK
VITREOUS CHINA
REMINISCENCE™ PEDESTAL SINK
•Vintage-styled basin with raised motif backsplash and design-coordinated pedestal
•Made from vitreous china
•Rear overflow
•Supplied with mounting kit
•Design matched to Reminiscence toilet
•Faucet ledge
Shown with 3801.452 Amarilis Jasmine faucet and handles (not included)
0211.800 Faucet holes on 8" (203mm) centers (Illustrated)
0211.400 Faucet holes on 4" (102mm) centers
0211.100 Center hole only
Nominal Dimensions:
660 x 508 x 864mm (26" x 20" x 34")
Separate Components:
0211.008 Pedestal top-8" (203mm) centers
0211.004 Pedestal top-4" (102mm) centers
0211.001 Pedestal top-center hole only
734900-400 Pedestal only
|
552mm |
|
FINISHED |
(21-3/4) |
|
|
|
|
WALL |
203mm |
10mm |
|
(8) |
|
|
(3/8) |
|
|
|
|
140mm |
|
108mm |
(5-1/2 REF.) |
|
(4-1/4) |
206mm
PEDESTAL (8-1/8) TO WALL CLEARANCE
508mm
(20)
PEDESTAL ANCHORING |
C/L |
|
SCREW HOLES |
||
|
8mm (5/16) DIA.
Bowl sizes:
476mm (18-3/4") wide 292mm (11-1/2") front to back 133mm (5-1/4") deep
Compliance Certifications -
Meets or Exceeds the Following Specifications:
• ASME A112.19.2M for Vitreous China Fixtures
To Be Specified: |
|
Color: White |
Bone Linen |
Silver |
Fawn Beige Black |
Faucet*:
Faucet Finish:
Supplies:
1-1/4" Trap:
* See faucet section for additional models available
© 2008 AS America Inc.
660mm |
|
|
(26) |
70mm |
|
260mm |
||
(2-3/4) |
||
(10-1/4) |
||
|
||
|
DRAIN |
|
|
CHASE |
|
178mm |
|
|
(7) |
|
|
19mm (3/4) DIA. |
|
|
HOLES FOR |
|
|
ANCHOR BOLTS |
|
|
203mm |
|
178mm |
(8) |
|
|
|
|
(7) |
SUPPLIES |
|
|
AS REQ'D |
|
|
1-1/4 O.D. |
|
|
WASTE |
864mm |
|
1-1/4 O.D |
|
|
(34) |
|
|
TAILPIECE |
REF. |
|
*597mm |
400mm |
|
(23-1/2) |
|
|
*546mm |
(15-3/4) |
|
(21-1/2) |
|
|
FINISHED |
|
|
FLOOR |
|
|
210mm |
PEDESTAL |
|
SIDE SECTION |
|
|
(8-1/4) |
|
|
|
NOTES:
* DIMENSIONS SHOWN FOR LOCATION OF SUPPLIES AND “P" TRAP ARE SUGGESTED.
▼ PEDESTAL ANCHORING SCREWS NOT INCLUDED.
■ SUITABLE FOR REINFORCEMENT ONLY. ACTUAL DIMENSIONS MUST BE TAKEN FROM FIXTURE.
FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY. PROVIDE SUITABLE REINFORCEMENT FOR ALL WALL SUPPORTS. INSTALLATION INSTRUCTIONS SUPPLIED WITH LAVATORY.
IMPORTANT: Dimensions of fixtures are nominal and may vary within the range of tolerances established by ANSI Standard A112.19.2.
These measurements are subject to change or cancellation. No responsibility is assumed for use of superseded or voided pages.
J2
Revised 2/08