CADET™ ROUND FRONT TOILET
2798.012
•Vitreous china
•Low-consumption (6.0 Lpf/1.6 gpf)
•Round front siphon action jetted bowl
•Fully glazed 2" trapway
•AquaForce flushing technology
•Close-coupled tank with raised lip detail on tank cover
•Color-matched trip lever
•Speed Connect® tank/bowl coupling system
•Sanitary bar on bowl
•2 bolt caps
•100% factory flush tested
3454.016 Bowl
4112.016 Tank
Nominal Dimensions:
699 x 495 x 762mm (27-1/2" x 19-1/2" x 30")
Fixture only, seat and supply by others
Alternate Tank Configurations Available:
4112.300 Tank complete with chrome all metal trip lever
4112.500 Tank complete with Aquagard Liner
4112.600 Tank complete with tank cover locking device
4112.700 Tank complete with Aquagard Liner and tank cover locking device
4112.800 Tank complete with trip lever located on right side
4112.900 Tank complete with tank cover device and trip lever located on right side
Compliance Certifications -
Meets or Exceeds the Following Specifications:
•ASME A112.19.2M for Vitreous China Fixtures - includes Flush Performance, Ball Pass Diameter, Trap Seal Depth and all Dimensions
To Be Specified:
Color: White Bone Linen Silver
Fawn Beige Black
Seat: American Standard #5322.011 “Rise and Shine” solid plastic closed front seat with cover.
Seat: American Standard #5308.014 “Laurel” molded closed front seat with cover.
Alternate Seat:
Supply with stop:
©2008 AS America Inc.
CADET™
ROUND FRONT TOILET
VITREOUS CHINA
FINISHED WALL |
|
|
|
|
699mm |
|
|
|
(27-1/2) |
|
|
19mm ± 6mm |
|
495mm |
|
(3/4 ± 1/4) |
|
|
|
|
225mm |
|
(19-1/2) |
|
|
|
|
|
(8-7/8) |
|
|
|
419mm |
|
|
|
(16-1/2) |
|
|
|
C/L OF SEAT POST HOLES |
|
|
|
140mm (5-1/2 CENTERS) |
|
|
|
|
|
762mm |
|
|
SUPPLY |
(30) |
|
|
AS |
|
83mm 1/4)-(3 |
|
REQ'D |
|
|
381mm |
|
|
|
|
(15) |
|
|
|
*222mm(8-3/4) |
381mm |
|
|
(15) |
|
|
|
152mm |
|
|
16mm |
(6) |
|
|
(5/8) |
FINISHED |
|
|
|
|
|
178mm |
305mm |
FLOOR |
241mm |
(7) |
|
(9-1/2) |
|
(12) |
|
||
305mm |
C/L OF OUTLET |
|
|
(12) |
|
|
|
|
|
|
NOTES:
THIS COMBINATION IS DESIGNED TO ROUGH-IN AT A MINIMUM DIMENSION OF 305MM (12") FROM FINISHED WALL TO C/L OF OUTLET.
* DIMENSION SHOWN FOR LOCATION OF SUPPLY IS SUGGESTED. SUPPLY NOT INCLUDED WITH FIXTURE AND MUST BE ORDERED SEPARATELY.
IMPORTANT: Dimensions of fixtures are nominal and may vary within the range of tolerance established by ANSI Standard A112.19.2
These measurements are subject to change or cancellation. No responsibility is assumed for use of superseded or voided pages.
K87
Revised 2/08