American Standard R110, R115, R110BP, R110SS, R110SSBP Installation Manual

Installation Instructions

Instrucciones de instalación

Mode d’installation

ROUGH VALVE KIT	R110, R110BP, R110SS, R110SSBP
JUEGO DE VÁVULA SIN ACABADO	R115, R115BP, R115SS, R115SSBP
ENSEMBLE DE ROBINET ROBUSTE

PRESSURE BALANCE TEMPERATURE CONTROL VALVE

VÁLVULA DE CONTROL DE TEMPERATURA CON EQUILIBRO DE PRESIÓN ROBINET MITIGEUR

Thank you for selecting American-Standard...the benchmark of fine

quality for over 100 years. To ensure that your installation proceeds smoothly-- please read these instructions carefully before you begin.

Gracias por seleccionar los productos American Standard, sinónimo de la mejor calidad durante más de 100 años. Por favor lea estas instrucciones detenidamente antes de comenzar para que lleve a cabo la instalación sin contratiempos.

Nous vous remercions d’avoir choisi American Standard… synonyme de qualité supérieure depuis plus de 100 ans. Pour vous assurer que l’installation se déroulera sans difficulté, veuillez lire attentivement ces instructions avant de commencer.

Certified to comply with ANSI A112.18.1 Cumplimiento certificado de los requisitos de la norma ANSI A112.18.1

Certifié conforme à ANSI A112.18.1

U.S. Patent No. D403,750

Patente estadounidense D403,750

Brevet USA no. D403.750

M968382A

ROUGHING-IN DIMENSIONS

DIMENSIONES DE DESBASTADO

DIMENSIONS DE PRÉPARATION

To assure proper positioning in relation to wall, note roughing-in dimensions.

Tome nota de las dimensiones de desbastado para asegurar la posición correcta respecto de la pared.

Pour garantir un bon positionnement par rapport au mur, tenir compte des dimensions de préparation.

OUTLETS 1/2" NOM.

1-5/8" TO 3-1/4"

COPPER SWEAT

FINISHED WALL

1-5/8" A 3-1/4" (41 MM A 83 MM)

SALIDA, 1/2" (12,7 MM)

PARED TERMINADA

41 mm (1-5/8 po.) À 83 mm (3-1/4 po.)

INLETS 1/2" NPT

NOM. COBRE SOLDADO

PAROI FINIE

ENTRADAS, 1/2"

ORIFICE CUIVRE LISSE

1/2" NPT

12,7 mm (1/2 po.) NOM.

(12,7 mm) NPT

1/2" (12,7 MM) NPT

ENTRÉES 12,7 mm

INLETS 1/2" NOM.

4-1/16"

NPT 12,7 mm (1/2 po.)

(1/2 po.)

COPPER SWEAT

(103 MM)

3-3/8"

ENTRADAS, 1/2" (12,7 MM)

(86 mm)

NOM. COBRE SOLDADO

3-3/8"

ENTRÉES CUIVRE LISSE

OPTIONAL TO FINISHED FLOOR

(86 mm)

12,7 mm (1/2 po.) NOM.

4-1/16"

USUALLY BETWEEN 65'' AND 78''

(103 MM)

OPTATIVO AL PISO TERMINADO,

POR LO GENERAL ENTRE

OUTLETS 1/2" NPT

65" Y 78" (165 A 198 cm)

SALIDA, 1/2"

DISTANCE ENTRE OPTION ET

(12,7 mm) NPT

PLANCHER FINI ENTRE

ORIFICE 12,7 mm

SWEAT INLETS

"SEE ILLUSTRATION"

165 cm ET 198 cm (65 à 78 po.)

(1/2 po.)

ENTRADAS SOLDADAS

"VEA LA FIGURA"

THREADED INLETS

"VOIR ILLUSTRATION"

ENTRÉES LISSES

ENTRADAS ROSCADAS

ENTRÉES FILETÉES

OUTLETS 1/2" NOM.

COPPER SWEAT

SALIDA, 1/2" (12,7 MM)

NOM. COBRE SOLDADO

ORIFICE CUIVRE LISSE

OUTLETS 1/2" NPT

12,7 mm (1/2 po.) NOM.

5-7/8"

SALIDA, 1/2"

5-7/8"

INLETS

INLETS 1/2" NOM.

18" OPTIONAL

OPTATIVO, 18" (45,7 cm)

(12,7 mm) NPT

(149 MM)

1/2" NPT

(149 MM)

COPPER SWEAT

ORIFICE 12,7 mm

OPTION 45,7 cm (18 po.)

ENTRADAS, 1/2"

ENTRADAS, 1/2" (12,7 MM)

(1/2 po.)

(12,7 MM) NPT

NOM. COBRE SOLDADO

3-3/8"

ENTRÉES NPT

ENTRÉES CUIVRE LISSE

(86 mm)

12,7 mm (1/2 po.)

4-1/16"

12,7 mm (1/2 po.) NOM.

TOP OF TUB RIM

1/2" NPT

(103 MM)

4"

1/2" (12,7 MM) NPT

THREADED INLETS (STOPS)

BORDE SUPERIOR

NPT 12,7 mm (1/2 po.)

DE LA BAÑERA

1/2" COPPER

ENTRADAS ROSCADAS (LIMITADORES)

HAUT REBORD

ENTRÉES FILETÉES (BUTÉES)

SWEAT INLETS (STOPS)

BAIGNOIRE

1/2" (12,7 mm)

COBRE

ENTRADAS SOLDADAS (LIMITADORES)

BOTTOM OF TUB

12,7 mm

ENTRÉES LISSES (BUTÉES)

(1/2 po.) CUIVRE

FONDO DE LA BAÑERA

FOND BAIGNOIRE

1	ROUGHING-IN	CAUTION	Turn off water at main supply.

NOTE When soldering, remove PLASTER GUARD, CARTRIDGES and CHECK STOPS (IF PRESENT). When finished soldering,

flush valve body, replace cartridges, check stops (if present) and plaster guard to continue installation. Use thread sealant or Teflon tape on threaded connections.

5

7 1

See Roughing-in diagram before starting. Connections are:

1/2" copper sweat for sweat inlets

1/2" female NPT for threaded inlets Connect RISER PIPE (1) to MANIFOLD (2) top outlet marked "SHR".

Connect TUB FILLER PIPE (3) at bottom outlet marked "TUB".

For proper positioning the finished wall must be within side wall of PLASTER GUARD (4).

If the valve is installed on a fiberglass

or other thin wall application, the 4 PLASTER GUARD (4) can be used as a support.

Cut a 3" dia. hole in the shower stall.

If STOPS are used, drill two additional 1" holes to allow access to the stops.

Remove PLASTER GUARD (4), rotate 180˚

so that indicated screw holes fit MANIFOLD (2). Push CAP on valve, place ESCUTCHEON on and

attach with screws.

Connect hot and cold water supplies.

Cap off shower pipe (5) and tub filler pipe (6).

For support, use pipe BRACES (7) secured to wooden braces. With valve turned off, turn on water supplies.Check for leaks.

HOT

2

COLD

PLUG

3

6