Installation
Instructions
SERIN™ |
T064.60X |
|
BATH/SHOWER TRIM KIT WITH DIVERTER
Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin.
To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.
Certified to comply with ANSI A112.18.1
M968836 Rev . 1 . 4
Recommended Tools
|
Flat Blade Screwdriver |
|
|
Pipe Wrench |
Plumbers' Putty or Caulking |
Adjustable Wrench |
Channel Locks |
|
|||
|
Phillips Screwdriver |
|
|
ROUGHING-IN DIMENSIONS |
|
CARE INSTRUCTIONS: |
|
|
|
|
|
To assure proper positioning in relation to wall, note |
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH |
||
roughing-in dimensions. |
|
CLEAR WATER. DRY WITH A SOFT COTTON |
|
|
1-5/8" TO 3-1/4" |
FLANNEL CLOTH. |
|
FINISHED WALL |
|
DO NOT: DO NOT CLEAN THE PRODUCT WITH |
|
|
1/2" NPT |
SOAPS, ACID, POLISH, ABRASIVES, HARSH |
|
|
CLEANERS, OR A CLOTH WITH A COARSE |
||
|
|
||
|
|
SURFACE. |
|
5-5/8" REF. |
OPTIONAL TO |
|
|
2-3/8" |
|
|
|
FINISHED FLOOR |
|
|
|
|
|
|
|
|
USUALLY BETWEEN |
|
|
8-1/8" REF. |
80'' AND 86' |
|
|
|
|
|
|
74" FOR |
|
|
|
HEAD CLEARANCE |
|
|
|
|
"SEE ILLUSTRATION" |
OUTLETS 1/2" NPT |
|
|
SHW |
|
|
7-1/4" D. |
|
|
|
|
TUB |
|
|
18" |
|
|
5-5/8" |
OPTIONAL |
|
|
|
6-3/4" |
|
|
|
|
1/2" NPT |
1-3/4" |
|
|
|
|
1/2" REF. |
|
TOP OF |
4" |
|
TUB RIM |
INLETS |
5-5/8" |
BOTTOM OF |
1/2" NPT |
|
|
THREADED INLETS (STOPS) |
|
TUB |
|
|
|
|
1 INSTALL DIVERTER
When finished tiling the wall, remove PLASTER GUARD (1). Remove two screws that secure the DIVERTER LID (2) and
remove Lid. Inspect the inside surface of diverter port. 2 Diverter port must be free of any dirt. Clean if necessary.
Install DIVERTER (3) with SCREWS (4) removed with
DIVERTER LID (2).
Operate DIVERTER (3). DIVERTER (3) should slide in and out smoothly.
3
1 |
4 |
DIVERTER PORT
2 INSTALL VALVE TRIM
Figure 1. Push CAP (1) over VALVE CARTRIDGE (2) until seated against stop. Push CAP (3) over DIVERTER (4) until seated against stop.
Figure 2. Push ESCUTCHEON HOLDER (5) onto CAP (1) and attach to valve body with SCREWS (6). Mount ESCUTCHEON SUPPORT (7) to ESCUTCHEON HOLDER (5) with SCREWS (8).
Figure 3. Install ESCUTCHEON (9) onto CAP (1) and push flush against finished wall. Escutcheon (9) will snap fit onto ESCUTCHEON SUPPORT (7).
5
7
1
6
Figure 2.
8
4
3
2
Figure 1. |
1 |
9 7 1
Figure 3.
M968836 Rev . 1 . 4