American Standard Neolo Elongated Flush Valve Toilet 2531.016, Neolo Elongated Flush Valve Toilet 2530.016, Neolo Elongated Flush Valve Toilet 2529.016 User Manual

187.86 Kb
Loading...

NEOLO™

ELONGATED FLUSH VALVE TOILET

VITREOUS CHINA

NEOLO™ ELONGATED FV TOILET

Elongated flush valve toilet

Vitreous china

Low consumption (6.0 Lpf/1.6gpf)

Wall outlet elongated bowl, angle back and base

Siphon jet flush action

Fully glazed 2" ballpass trapway

10" x 13" water surface area

1-1/2" inlet spud

4 bolt caps

100% factory flush tested

2529.016 Elongated bowl only, top spud, wall outlet

2530.016 Elongated bowl only, back spud, wall outlet

2531.016 Elongated bowl only, back spud, wall outlet, integral seat

Nominal Dimensions:

673 x 375 x 375mm

(26-1/2" x 14-3/4" x 14-3/4")

SEE REVERSE FOR ROUGHING-IN DIMENSIONS

Recommended working pressure – between 30 psi at valve when flushing and 80 psi static

Fixture only, less seat, bolt caps, and flush valve

Compliance Certifications -

Meets or Exceeds the Following Specifications:

• ASME A112.19.2 for Vitreous China Fixtures

To Be Specified:

Color: White

Seat: Olsonite #95 open front seat less cover

Seat: Church #9500C open front seat less cover

Seat: Pressalit seats for American Standard, closed front seat with cover (thermoset compound material).

Alternate Seat:

Flush Valve:

American Standard Selectronic#6065.161.002 DC Power(Top Spud)

American Standard Selectronic#6065.262.007 DC Power (Back Spud)

American Standard Selectronic#6067.262.007 AC Power (Back Spud)

American Standard Selectronic#6068.262.007 Multi AC Power (Back Spud)

 

M51

 

© 2008 AS America Inc.

Revised 11/08

 

 

 

 

 

 

 

 

NEOLO™

 

 

 

 

ELONGATED FLUSH VALVE TOILET

 

 

 

 

 

 

 

VITREOUS CHINA

2529.016

 

 

 

 

2530.016

 

 

 

 

 

 

1" N.P.T. OR C.W.T.

 

 

 

 

 

 

 

SUPPLY TO FLUSH VALVE

 

 

 

 

 

FINISHED WALL

 

 

 

 

 

 

 

 

 

 

121 mm

 

FINISHED WALL

 

 

 

673mm

 

 

(4-3/4)

 

 

 

 

 

 

 

 

 

673mm

 

 

 

(26-1/2)

 

 

 

 

 

 

 

 

 

 

 

(26-1/2)

 

 

 

 

 

 

 

 

 

 

 

1-1/2" SPUD

 

375mm

 

C/L OF SEAT POST HOLE

 

76mm

C/L OF SEAT POST HOLE

(14-3/4)

 

 

 

140mm (5-1/2) CENTERS

 

 

 

 

 

(3)

140mm (5-1/2) CENTERS

 

 

 

(2530.016)

 

 

 

 

 

 

 

 

470mm

 

375mm

 

470mm

 

 

660mm

 

(18-1/2)

 

 

 

 

 

 

(14-3/4)

 

(18-1/2)

 

 

(26)

 

INTEGRAL SEAT

 

 

13mm(1/2)

 

 

 

 

 

(2531.016)

 

 

 

 

 

 

IN WALL

13mm

 

SPUD

 

 

 

 

 

70mm (2-3/4)

 

 

 

 

 

 

 

 

DIA. HOLE

 

 

1-1/2"

 

 

 

 

 

 

(1/2)

 

 

375mm

 

 

 

 

225mm

 

 

C/L OF

 

375mm

 

(8-7/8)

C/L OF

375mm

 

(14-3/4)

 

 

 

 

 

OUTLET

 

(14-3/4)

 

 

OUTLET

(14-3/4)

 

 

 

 

 

152mm

 

 

 

152mm

 

 

 

 

(6)

 

 

 

(6)

 

 

 

 

 

108mm

 

 

 

108mm

 

 

 

 

(4-1/4)

 

 

222mm

(4-1/4)

 

 

 

222mm

 

267mm

 

 

267mm

 

 

191mm (7-1/2)

FINISHED

(8-3/4)

 

 

 

(8-3/4)

 

 

FINISHED

(10-1/2)

 

 

(10-1/2)

 

 

DIA. HOLE

FLOOR

 

 

 

FLOOR

 

 

 

 

 

 

 

IN WALL

 

 

 

 

 

 

 

 

 

521mm

C/L OF 1/2" DIA. BOLT

 

 

 

C/L OF 1/2" DIA. BOLT

 

(20-1/2)

 

 

521mm

 

HOLES ON 140mm (5-1/2) CENTERS

 

HOLES ON 140mm (5-1/2) CENTERS

 

 

 

 

 

(20-1/2)

 

 

 

 

 

 

 

 

 

 

 

 

NOTES:

WASTE OUTLET SEAL RING MUST BE NEOPRENE OR GRAPHITE-

FELT (WAX RING NOT RECOMMENDED).

TO COMPLY WITH AREA CODE GOVERNING THE HEIGHT OF VACUUM

BREAKER ON FLUSH VALVE, THE PLUMBER MUST VERIFY

DIMENSIONS SHOWN FOR SUPPLY ROUGHING.

FLUSH VALVE NOT INCLUDED AND MUST BE ORDERED SEPARATELY.

IMPORTANT: Dimensions of fixtures are nominal and may vary within the range of tolerances established by ANSI Standard A112.19.2. These measurements are subject to change or cancellation. No responsibility is assumed for use of superseded or voided pages.

M52

© 2008 AS America Inc.

Revised 11/08