LEXINGTON™
PEDESTAL SINK
VITREOUS CHINA
LEXINGTON™ PEDESTAL SINK
•Minimalistic styled pedestal sink
•Made from vitreous china
•Rear overflow
•Supplied with mounting kit
•Faucet ledge
Shown with 8871.902 Amarilis faucet with Lexington handles (not included)
0178.514 Faucet holes on 8" (203mm) centers (Illustrated)
0178.536 Center Hole only
Nominal Dimensions:
616 x 464 x 867mm (24-1/4" x 18-1/4" x 34-1/2")
Separate Components:
0178.027 Pedestal top-8" (203mm) centers
0178.152 Pedestal top-center hole only
730500-400 Pedestal only
Bowl sizes:
445mm (17-1/2") wide 276mm (10-7/8") front to back 143mm (5-5/8") deep
Compliance Certifications -
Meets or Exceeds the Following Specifications:
• ASME A112.19.2M for Vitreous China Fixtures
To Be Specified: |
|
Color: White |
Bone Linen |
Silver |
Fawn Beige Black |
Faucet*:
Faucet Finish:
Supplies:
1-1/4" Trap:
* See faucet section for additional models available
203mm
(8)
102mm |
|
|
|
70mm |
|
|
|
|
(4) |
|
|
|
(2-3/4) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
197mm FINISHED (7-3/4)
WALL
464mm (18-1/4)
PEDESTAL ANCHOR SCREW HOLES (2)10mm (3/8) DIA.
|
|
|
565mm |
|
|
|
|
(22-1/4) |
|
|
|
|
610mm |
|
|
|
|
(24-1/4) |
|
|
|
|
|
19mm (3/4) DIA. |
10mm |
|
|
254mm |
HOLES FOR |
|
|
ANCHOR BOLTS |
||
(3/8) |
|
|
(10) |
|
|
|
|
||
|
|
|
|
DRAIN |
187mm |
|
|
|
CHASE |
*330mm |
|
|
|
|
(7-3/8) |
|
|
*286mm |
|
|
|
|
||
|
(13) |
|
|
|
|
|
|
|
(11-1/4) |
|
|
|
|
876mm |
|
|
|
|
(34-1/2) |
178mm |
|
203mm |
|
|
(7) |
|
(8) |
|
SUPPLIES AS |
|
|
|
|
|
|
|
|
|
REQUIRED |
|
1-1/4 O.D. |
|
|
|
|
|
WASTE |
|
OPEN TO |
|
|
|
|
|
|
1-1/4 O.D. |
|
FLOOR |
|
|
|
|
||
|
TAILPIECE |
|
FINISHED |
|
|
|
|
|
FLOOR |
|
|
|
|
178mm |
|
|
|
|
(7) |
|
NOTES: |
||
|
* DIMENSIONS SHOWN FOR LOCATION OF SUPPLIES AND “P" TRAP ARE |
||
|
SUGGESTED. |
||
|
▼ PEDESTAL ANCHORING SCREWS NOT INCLUDED. |
||
|
■ SUITABLE FOR REINFORCEMENT ONLY. ACTUAL DIMENSIONS MUST |
||
|
BE TAKE FROM FIXTURE. |
||
|
FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY. |
||
|
PROVIDE SUITABLE REINFORCEMENT FOR ALL WALL SUPPORTS. |
||
|
INSTALLATION INSTRUCTIONS SUPPLIED WITH LAVATORY. |
||
|
IMPORTANT: Dimensions of fixtures are nominal and may vary within the |
||
|
range of tolerances established by ANSI Standard A112.19.2. |
||
|
These measurements are subject to change or cancellation. No responsibility |
||
|
is assumed for use of superseded or voided pages. |
||
|
J5 |
|
|
© 2008 AS America Inc. |
Revised 2/08 |
||
|