CADET™ ELONGATED
PRESSURE-ASSISTED TOILET
2333.100
•Vitreous china
•Low-consumption (6.0 Lpf/1.6 gpf)
•Elongated bowl
•Pressure-assisted siphon jet flush action
•Fully-glazed 2" ballpass trapway
•10" x 12" water surface area
•Side-mounted chrome trip lever
•Close-coupled flushometer tank*
•Speed Connect® tank/bowl coupling system
•2 bolt caps
•100% factory flush tested
3099.016 Bowl with two bolt caps
4098.100 Tank complete with coupling components
Nominal Dimensions:
787 x 495 x 737mm (31" x 19-1/2" x 29")
Fixture only, seat and supply by others
Recommended working pressure range 20 psi - 80 psi
Alternate Configurations Available:
3099.203 Elongated bowl only with slotted rim for bedpan holding
4098.700 Tank and tank cover only with tank cover locking device
4098.800 Tank and tank cover only with right hand trip lever
4098.900 Tank complete with right hand trip lever and tank cover locking device
Compliance Certifications -
Meets or Exceeds the Following Specifications:
• ASME A112.19.2 for Vitreous China Fixtures
To Be Specified: |
|
|
Color: White |
Bone |
Linen |
Silver |
Fawn |
Beige Black |
Seat: American Standard #5324.019 “Rise and Shine" (with easy to clean lift-off hinge system) solid plastic closed front seat with cover.
Seat: American Standard #5311.012 “Laurel" molded closed front seat with cover.
Alternate Seat:
Supply with Stop:
* Flushmate III tank system by Flushmate® Div. of Sloan Valve Co © 2008 AS America Inc.
CADET™ ELONGATED PRESSURE-ASSISTED TOILET
VITREOUS CHINA
FINISHED WALL |
|
||
|
|
31 |
|
|
|
(787mm) |
|
3/4 ± 1/4 |
|
|
|
(19mm |
± 6mm) |
|
|
|
|
225mm |
|
|
|
(8-7/8) |
|
|
|
18-1/2 |
|
|
|
(470mm) |
|
|
|
C/L OF SEAT POST HOLES |
|
|
|
5-1/2 (140mm CENTERS) |
|
1/4-3 (83mm) |
|
|
14 |
|
|
|
(356mm) |
|
|
5/8 |
|
|
|
(16mm) |
FINISHED |
|
|
13 |
|
5-3/4 |
|
FLOOR |
|
|
(330mm) |
||
(146mm) |
|
|
|
|
|
|
|
12 |
|
|
|
(305mm) |
C/L OF OUTLET |
|
|
|
|
|
19-1/2 (495mm)
29 SUPPLY (737mm)
AS
REQ'D
15 *8 (381mm)
(203mm)
*6
(152mm)
9-3/4 (248mm)
NOTES:
THIS COMBINATION IS DESIGNED TO ROUGH-IN AT A MINIMUM DIMENSION OF 305MM (12") FROM FINISHED WALL TO C/L OF OUTLET. *DIMENSION SHOWN FOR LOCATION OF SUPPLY IS SUGGESTED. SUPPLY NOT INCLUDED WITH FIXTURE AND MUST BE ORDERED SEPARATELY.
FOR ADDITIONAL INFORMATION REFER TO INSTALLATION INSTRUCTIONS SUPPLIED.
IMPORTANT: Dimensions of fixtures are nominal and may vary within the range of tolerances established by ANSI Standard A112.19.2. These measurements are subject to change or cancellation. No responsibility is assumed for use of superseded or voided pages.
M46
Revised 2/08