|
Installation |
|
Instructions |
ARCH |
4101.301 |
HI-FLOW KITCHEN FAUCET |
|
with SIDE SPRAY |
|
Thank you for selecting American-Standard...
the benchmark of fine quality for over 100 years.
To ensure that your installation proceeds smoothly-- please read these instructions carefully before you begin.
4101.301 shown with |
4101.301 |
optional escutcheon 4101.000P
Certified to comply with ANSI A112.18.1M
M968583
RECOMMENDED
TOOLS
Adjustable Wrench Regular Screwdriver Phillips Screwdriver Channel Locks
1 |
INSTALL FAUCET WITH DECK ESCUTCHEON |
|
|
|
CAUTION |
Turn off water at |
|
||
(4101.351) |
|
|||
main supply. |
|
Installation with DECK ESCUTCHEON: Apply a light bead of plumbers putty to underside of ESCUTCHEON (1) if mounting surface is uneven. Place ESCUTCHEON (1) onto sink or mounting surface with large opening to the right as shown. Insert supply HOSES (2) and SHANK (3) through ESCUTCHEON (1) and mounting surface. Make sure slot in fitting base aligns with tab on ESCUTCHEON (1). Figure 1.
Assemble RUBBER WASHER (4), BRASS WASHER (5), and threaded LOCKNUT (6) onto SHANK (3) from underside of sink or mounting surface. Hand tighten LOCKNUT (6) and check that rotation of HANDLE (7) from HOT to COLD is centered.
Use a screwdriver to tighten SCREWS (8) on LOCKNUT (6). Work your way around LOCKNUT (6), tightening the SCREWS (8) slightly each time until all are snug to ensure even pressure.
Install SPRAY HOLDER: Insert SPRAY HOLDER (11) into ESCUTCHEON (1). From underside of sink or mounting surface thread LOCKNUT (12) onto SPRAY HOLDER (11) shank and tighten.
Install SPOUT ASSEMBLY: Insert SPRAY HOSE (9) and SHANK (10) through ESCUTCHEON (1) and mounting surface. Make sure slot in spout base aligns with tab on ESCUTCHEON (1). Figure 2.
Assemble RUBBER WASHER (4a), BRASS WASHER (5a), and threaded LOCKNUT (6a) onto SHANK (10) from underside of sink or mounting surface. Hand tighten LOCKNUT (6a). Use a screwdriver to tighten SCREWS (8a) on LOCKNUT (6a) the same as fitting installation above.
7
Figure 1
Figure 2
SLOT
|
3 |
11 |
1 |
|
2 |
ALIGN SLOT AND TAB
TAB
SLOT
ALIGN SLOT
AND TAB 10
TAB
|
4 |
5 |
1 |
4a |
|
|
|
5a |
|||
|
|
6 |
|
||
12 |
|
|
|
6a |
|
|
8 |
|
|
||
|
|
|
8a |
9 |
|
|
|
|
|
||
|
|
|
|
|
1a |
INSTALL FAUCET WITHOUT ESCUTCHEON PLATE |
(4101.115 with soap dish) (4101.350 less soap dish) |
Insert SEAL WASHER (1) into ESCUTCHEON (2). Place ESCUTCHEON (2) onto sink or mounting surface. Insert supply TUBES (3) and SHANK (4) through ESCUTCHEON (2) and mounting surface.Make sure slot in fitting base aligns with tab on ESCUTCHEON (2). Figure 1.
Assemble RUBBER WASHER (5), BRASS WASHER (6) and threaded LOCKNUT (7) onto SHANK (4) from underside of sink or mounting surface. Hand tighten LOCKNUT (7) and check that rotation of HANDLE (8) from HOT to COLD is centered.
Use a screwdriver to tighten SCREWS (9) on LOCKNUT (7). Work your way around LOCKNUT (7), tightening the SCREWS (9) slightly each time until all are snug to ensure even pressure.
Install SPRAY HOLDER: Insert SPRAY HOLDER (11) into ESCUTCHEON (12). Insert SEAL (14) into underside of ESCUTCHEON (12). From underside of sink or mounting surface thread LOCKNUT (13) onto SPRAY HOLDER (11) shank and tighten.
Install SPOUT ASSEMBLY: Insert SEAL WASHER (1a) into ESCUTCHEON (2a). Insert SPOUT HOSE (10) and SHANK (11) through ESCUTCHEON (2a) and mounting surface. Make sure slot in spout base aligns with tab on ESCUTCHEON (2a).
Figure 2.
Assemble RUBBER WASHER (5a), BRASS WASHER (6a), and threaded LOCKNUT (7a) onto SHANK (11) from underside of sink or mounting surface. Hand tighten LOCKNUT (7a). Use a screwdriver to tighten SCREWS (9a) on LOCKNUT (7a) the same as fitting installation above.
|
|
|
|
8 |
|
|
|
|
Figure 1 |
|
|
Figure 2 |
|
|
|
|
SLOT |
|
|
|
|
|
4 |
|
|
|
|
|
|
|
|
ALIGN SLOT |
|
|
11 |
|
3 |
|
AND TAB |
|
|
|
TAB |
ALIGN SLOT |
|
|
||
|
|
2 |
|
|
||
|
|
|
SLOT |
|
||
|
|
|
AND TAB |
|
||
|
|
1 |
|
|
|
11 |
|
|
|
|
|
|
|
12 |
|
|
|
|
TAB |
2a |
14 |
|
|
|
|
|
|
|
|
|
|
1a |
|
|
|
|
|
|
|
|
|
|
|
5 |
6 |
|
|
|
|
|
|
|
|
|
|
|
13 |
|
7 |
|
5a |
|
|
|
9 |
|
6a |
||
|
|
|
|
|
||
|
|
|
|
|
|
7a |
|
|
|
|
|
9a |
10 |
|
|
|
|
|
|
|
2 MAKE WATER SUPPLY CONNECTIONS |
|
RED STRIPE |
||||
|
|
|
||||
2
Push HOSE END (1) with compression fitting onto COPPER TUBE (2) Make sure
HOSE and COPPER TUBE are fully engaged (approx.1/2" engagement). Use adjustable 1 wrench to tighten connections. Do not over tighten.
Turn off hot and cold water supplies before beginning.
1/2" ENGAGEMENT
Connect FLEXIBLE SUPPLIES (3) directly to wall supplies. Connection on fitting supplies are 3/8" compression. Connect left supply (Marked with a Red Stripe) to Hot and right supply to Cold wall supply. Use adjustable wrench to tighten connections. Do not over tighten.
Faucet supplies are 24-1/2" long from faucet base.
Note: If additional supply length is required, installer must purchase
those parts separately.
Important: If SUPPLY HOSES (3) are too long, loop as illustrated to avoid kinking.
3 |
COLD |
HOT |
|
M968583
Loading...