American Standard 6030Y2A.202.XXX, 6030Y2A.102.XXX User Manual

0 (0)
American Standard 6030Y2A.202.XXX, 6030Y2A.102.XXX User Manual

INSTALLATION INSTRUCTIONS

Acrylux Builder Series (Above Floor Rough)

Model 6030Y2A.102.XXX

Model 6030Y2A.202.XXX

Thank you for selecting American Standard – the benchmark of fine quality for over 100 years. To ensure this product is installed properly, please read these instructions carefully before you begin. Local building codes vary by location. Observe all local plumbing and building codes.

RECOMMENDED TOOLS AND MATERIALS

Tape Measure

Mortar Compound (optional)

Pencil

Saber Saw

Safety Glasses

Screws, 1" Flathead, Stainless

Drill

Level

6030Y2A.102.XXX

6030Y2A.202.XXX

1"

25mm

19"

483mm

18"

457mm

59-7/8" 1521mm

30"

762mm

STUD LAYOUT:

The American Standard Acrylux Bathtub will fit all standard 30" x 60" tub walls.

 

 

 

10"

 

 

 

 

 

 

 

14"

 

 

 

 

 

 

254mm

 

 

 

 

 

356mm

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

6"

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

31-1/2"

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

152mm

 

 

800mm

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Drain C

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

8"

 

 

 

 

 

 

 

 

 

 

 

 

L

 

Floor Cut Out

 

 

 

 

 

 

 

 

 

203mm

 

 

 

 

 

 

 

6" x 10"

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(152 x 254mm)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

60"

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1524mm

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

= stud location

LHO shown - Reverse for RHO

IMPORTANT:

Allow tub to reach room temperature before installation.

Read installation instructions carefully before starting project.

Keep instructions for warranty information.

INSTALLATION INSTRUCTIONS

STEP 1. PREPARING ALCOVE

Strip to bare studs.

Alcove studs should be constructed as shown above.

Floor must be clean, smooth, and level (check with level). Sub floor must be installed as in the stud layout. Do not install tub on open floor joists.

If required, cut hole in sub floor as shown above to accommodate drain.

STEP 2. INSTALLING TUB

Trial fit tub in prepared alcove. With tub sitting flat on floor, check with level on top of tub. Tub should be level from front-to-back and side-to-side (Fig 1).

A floor leveling compound (smooth mortar) or a similar quick-setting compound specifically made for leveling floors may be used to fully support and level base.

After tub is leveled, if alcove is larger than tub, shim between tub and studs to create a tight fit. Screw tub flange to studs (Fig. 2).

CLEANING

Do not use any abrasive cleaners or metal scrapers.

If drywall mud or plaster gets on your shower, it may be carefully removed with a wooden scraper made from a piece of scrap wood.

Adhesive may be removed with mineral spirits.

Ideal cleaners are Soft Scrub Gel® or Comet Gel®.

WARNING:

Some cleaning products are not suitable for use. Read all labels carefully.

DO NOT USE if they say “not suitable for use with ABS, acrylic, or polystyrene.

FIGURE 1. Check to assure tub is level.

FIGURE 2. If necessary, shim between tub and studs for tight fit and screw to each stud.

P r o d u c t n a m e s l i s t e d h e r e i n a r e t r a d e m a r k s o f A S A m e r i c a , I n c . © A S A m e r i c a , I n c . 2 0 0 8

754283-100 Rev. A

Loading...
+ 1 hidden pages