Installation
Instructions
Spread Lavatory Faucet with the Speed Connect™ Drain
Congratulations on purchasing your American Standard faucet with Speed Connect drain, a feature found only on American Standard faucets.
Speed Connect Drain*
•Fewer parts, installs in less time
•Never needs adjustment
•Guaranteed to seal properly the first time, every time.
7871.702
7871.712
7871.722
7871.732
7881.702
7881.712
7881.722
7881.732
Certified to comply with ANSI A112.18.1
U S 6 0 4 0 4 R e v. 1 . 2
*Your new American Standard faucet is designed to work only with the Speed Connect drain.
To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.
Recommended tools
Screwdriver Channel Locks Adjustable Wrench Tubing Cutter
1 |
|
|
Turn off hot and cold water |
|
INSTALL SPOUT |
CAUTION |
|||
|
supplies before beginning. |
|||
|
|
|
|
Insert SPOUT (1) and CABLE CONNECTOR (12) through center hole, making sure the SPOUT ESCUTCHEON (2) and SEAL WASHER (3) are properly seated.
Assemble RUBBER WASHER (4), BRASS WASHER (5) and LOCKNUT (6) onto SPOUT SHANK (7) from under side of sink . Make sure SPOUT (1) is centered in the mounting hole and the slot in the BRASS WASHER (5) faces toward the rear of the sink.
Tighten LOCKNUT (6) firmly. Fig. A.
1A INSTALL VALVE BODY
Place RUBBER RING (9) into SCUTCHEON (10).
Install LOCKNUT (11) onto VALVE BODY (8).
From under side of mounting surface, install VALVE BODY (8) through valve mounting holes. Threads of VALVE BODY (8) should extent at least 5/16 of a inch above mounting surface top. Fig. B. Thread ESCUTCHEON (10) onto VALVE BODY (8) until snug against internal stop. If necessary, adjust LOCKNUT (11).
Hand tighten LOCKNUT (11) to secure VALVE BODY (8). Repeat above steps for opposite VALVE BODY (8A).
1
|
10 |
10 |
|
9 |
9 |
5/16'' MIN. |
MOUNTING |
|
SURFACE |
|
|
Fig. B. |
|
|
|
11 |
8 |
|
|
|
|
8 |
11 |
Fig. A.
1
2
3
7
4
SLOT |
5 |
|
6
12
8A
7871 SERIES
1
2 POP-UP DRAIN
Remove CLEAR PLASTIC COVER (1).
Remove CARDBOARD SPACER (2) from under DRAIN POP-UP (3).
Tighten TAILPIECE (4) on DRAIN BODY before installing DRAIN BODY. Fig. B.
Fig. A. |
Fig. B. |
1 |
|
3 |
DRAIN |
BODY |
|
2 |
4 |
|
3 REMOVE FLANGE
Thread FLANGE (1) counter-clockwise and remove FLANGE (1) and FOAM GASKET (2) from drain body. Fig. A.
Thread LOCKNUT (3) clock-wise to bottom of drain body. Push GASKET (4) down against LOCKNUT (3). Fig. B.
Fig. A. |
Fig. B. |
1 |
|
4
2
3
4 |
INSTALL DRAIN FROM |
REAR OF SINK |
5 TIGHTEN LOCKNUT |
BELOW FIXTURE |
|||
|
From under side of SINK |
4 |
Tighten LOCKNUT (1) firmly with Adjustable |
|
install DRAIN BODY (1) up |
Wrench or Channel Locks. |
|
|
through drain outlet. |
|
|
|
Note: No plumber’s putty |
|
|
|
or caulk is required. |
3 |
|
|
The CABLE ATTACHMENT |
|
|
|
POINT (2) must face towards |
|
|
|
the rear of the SINK. |
1 |
1 |
|
Install FOAM GASKET (3) and |
||
|
2 |
|
|
|
FLANGE (4) onto drain body |
|
|
|
from above SINK and tighten |
|
|
|
FLANGE (4) firmly. |
|
|
6 FLANGE GASKET AND POP-UP KNOB
Check DRAIN FLANGE in SINK to ensure that WHITE FOAM GASKET (3) is fully compressed and not visible. Fig. A.
POP-UP KNOB (1) must be fully down. Fig. B.
Fig. A. |
Fig. B. DOWN |
1
WHITE FOAM |
|
GASKET |
DRAIN |
NOT VISIBLE |
FLANGE |
U S 6 0 4 0 4 R e v. 1 . 2
2