American Standard 6013, 6013S User Manual
Installation
Instructions
SWAN
Centerset Lavatory Faucet with the
Speed Connect™ Drain
Congratulations on purchasing your American Standard faucet with
the Speed Connect Drain, a feature found only on
American Standard faucets.
Speed Connect Drain*
• 1/3 of the parts, installs in 1/3 of the time
• No tools needed
• Never needs adjustment
• Guaranteed to seal properly the first time, every time.
*Your new American Standard faucet is designed to work only with the Speed Connect drain. Helpful tips for
removing your current drain can be found in the Troubleshooting section of these instructions.
To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.
Recommended tools
6013
6013S
Certified to comply with ANSI A112.18.1
M968468 REV 1.2
INSTALL FAUCET
1
Turn off hot and cold water supplies before beginning.
Insert FAUCET (1) and CABLE CONNECTOR (2) through
mounting holes of Sink or mounting surface.
Assemble LOCKNUTS (3) onto SHANKS (4) (from under
side of Sink). Hand tighten firmly.
(HAND TIGHTEN)
CAUTION
Turn off hot and cold water
supplies before beginning.
Fig. A.
Fig. B.
3
4
Fig. B.
4
SINK OR
MOUNTING
SURFACE
Adjustable Wrench Screwdriver Channel Locks
Fig. A.
Tubing Cutter
POP-UP
CABLE
3
2
1
2
INSTALL POP-UP DRAIN
2
Remove CLEAR PLASTIC COVER (1). Remove
CARDBOARD SPACER (2) from under DRAIN
POP-UP (3).
Drop DRAIN BODY (4) through sink drain
hole. Make sure WHITE FOAM GASKET (5)
is under flange of DRAIN BODY (4).
Note: No plumber’s putty or caulk is required.
The CABLE ATTACHMENT POINT (6) must
face towards the rear of the SINK.
INSTALL BLACK GASKET
3
Install BLACK CONE GASKET (1) onto DRAIN BODY (2)
from below.
Note: The flat side of the BLACK CONE GASKET (1) must
face down.
Fig. A.
Fig. B.
Fig. B.
Fig. A. Fig. B.
1
3
2
2
REAR OF
SINK
4
5
6
SINK
DRAIN
HOLE
INSTALL GRAY LOCKNUT
4
Install GRAY LOCKNUT (1) onto DRAIN BODY (2)
from below SINK. Fig. A.
Note: The flat side of the GRAY LOCKNUT (1)
must face up.
Tighten firmly by hand. No tools are required.
Check DRAIN FLANGE in SINK to ensure that
WHITE FOAM GASKET (3) is fully compressed
and not visible. Fig. B.
POP-UP KNOB
5
POP-UP KNOB (1) must be fully down.
Fig. A.
1
FLAT SIDE OF GASKET
MUST FACE DOWN
Fig. B.
2
DRAIN
FLANGE
FLAT SIDE OF
GRAY LOCKNUT
MUST FACE UP
WHITE FOAM
1
DOWN
3
GASKET
NOT VISIBLE
1
M968468 REV 1.2
2
ATTACH CABLE CONNECTOR
6
Thread CABLE CONNECTOR (1) clockwise
onto DRAIN BODY CONNECTION (2) and
hand tighten. Fig. A.
Your new POP-UP DRAIN installation is
now complete. Fig. B.
Note: Tailpeice on pop-up drain is 1-1/4” O.D.
Fig. B.
CHECK OPERATION OF POP-UP
7
Fig. A.
Fig. B.
1
1-1/4” O.D.
2
Operate LIFT KNOB (1) to verify that STOPPER (2) opens and
closes. Fig. B.
Note: If STOPPER (2) does not open and close properly then refer
to the “troubleshooting section” of these instructions.
MAKE WATER SUPPLY AND WASTE CONNECTIONS
8
NOTE: FLEXIBLE SUPPLIES OR BULL-NOSE RISERS MUST BE
PURCHASED SEPARATELY.
Connect water supply to FAUCET (1) with 1/2" IPS FLEXIBLE
SUPPLIES (2) or 3/8" O.D. BULL-NOSE RISERS (3).
Use adjustable wrench to tighten connections. Do not over tighten.
Be careful not to kink copper supply when bending. Use tubing
cutter to cut to proper length.
Connect 1-1/4” O.D. tailpiece on POP-UP DRAIN to
waste outlet.
1/2" PIPE
THREAD
1
2
1
COUPLING
2
FLEXIBLE
SUPPLIES
NUT
3
3/8 O.D.
BULL-NOSE
RISERS
3/8” COMPRESSION
CONNECTION
COMPRESSION
NUT
FERRULE
HOT COLD
M968468 REV 1.2
3
Loading...