CADET™ RIGHT HEIGHT 16-1/2" HEIGHT PRESSURE-ASSISTED EL TOILET
VITREOUS CHINA
BARRIER FREE
CADET™ RIGHT HEIGHT 16-1/2" PRESSURE-ASSISTED ELONGATED TOILET
2377.100
•Vitreous china
•Low-consumption (1.6 gpf/6.0 Lpf)
•Bowl rim at 16-1/2"
•Elongated bowl
•Pressure-assisted siphon jet flush action
•Fully-glazed 2" ballpass trapway
•10" x 12" water surface area
•Close-coupled Flushometer tank*
•Side-mounted chrome trip lever
•Speed Connect® tank/bowl coupling system
•Sanitary dam on bowl
•Two bolt caps
•100% factory flush tested
3109.016 Bowl with two bolt caps
4098.100 Tank complete with coupling components
Nominal Dimensions:
806 x 495 x 800mm (31-3/4" x 19-1/2" x 31-1/2")
Fixture only, seat and supply by others
Recommended working pressure range 20 psi - 80 psi
Alternate Configurations Available:
3109.456 Elongated bowl only with slotted rim for bedpan holding
4098.700 Tank and tank cover only with tank cover locking device
4098.800 Tank and tank cover only with right hand trip lever
4098.900 Tank complete with right hand trip lever and tank cover locking device
Compliance Certifications -
Meets or Exceeds the Following Specifications:
• ASME A112.19.2 for Vitreous China Fixtures
To Be Specified: |
|
|
Color: White |
Bone |
Linen |
Silver |
Fawn |
Beige Black |
Seat: American Standard #5324.019 “Rise and Shine” (with easy to clean lift-off hinge system) solid plastic closed front seat with cover.
Seat: American Standard #5311.012 “Laurel” molded closed front seat with cover.
Alternate Seat:
Supply with Stop:
* Flushmate III tank system by Flushmate® Div. of Sloan Valve Co © 2008 AS America Inc.
3-1/4 (83mm)
FINISHED WALL
31-3/4 (806mm)
3/4 ± 1/4 (19mm ± 6mm)
8-7/8 (225mm)
18-1/2 (470mm)
C/L OF SEAT POST HOLES
5-1/2 (140mm CENTERS)
SUPPLY AS
REQ'D
16-1/2 (419mm)
*10 (254mm)
19-1/2 (495mm)
31-1/2 (800mm)
15
(381mm)
|
|
|
6 |
|
|
5/8 |
|
(152mm)* |
|
|
(16mm) |
FINISHED |
|
|
|
13-3/8 |
|
||
5-3/4 |
FLOOR |
10 |
||
(340mm) |
||||
(146mm) |
|
(254mm) |
||
|
|
|||
12 |
|
|
|
|
(305mm) |
C/L OF OUTLET |
|
|
|
|
|
|
NOTES:
THIS TOILET IS DESIGNED TO ROUGH-IN AT A MINIMUM DIMENSION OF 305mm (12") FROM FINISHED WALL TO C/L OF OUTLET.
SUPPLY NOT INCLUDED WITH FIXTURE AND MUST BE ORDERED SEPARATELY.
*DIMENSION SHOWN FOR LOCATION OF SUPPLY IS SUGGESTED.
IMPORTANT: Dimensions of fixtures are nominal and may vary within the range of tolerances established by ANSI Standard A112.19.2. These measurements are subject to change or cancellation. No responsibility is assumed for use of superseded or voided pages.
MEETS THE AMERICANS WITH DISABILITIES ACT GUIDELINES AND ANSI A117.1 REQUIREMENTS FOR ACCESSIBLE AND USABLE BUILDING FACILITIES - CHECK LOCAL CODES.
M45
Revised 2/08