WILLIAMSBURG ELITE™ 5'
INTEGRAL APRON WITH REMOVABLE ACCESS PANEL HIGH GLOSS ACRYLIC SHOWN LESS ALL FITTINGS
2425E-LHO
2425E-RHO WHIRLPOOL
INSTALLATION INSTRUCTIONS
|
|
|
60 |
|
|
|
|
12 |
(1524mm) |
|
|
|
|
10-1/4 |
(305mm) |
|
|
WATER |
|
|
|
|
RETENTION |
|
|||
|
|
|
|
|||
(260mm) |
|
|
|
FLANGE |
|
|
3/4 |
|
|
|
|
||
|
|
(8) JETS |
(3 SIDES) |
|
||
(19mm) |
|
|
|
|||
|
|
|
|
|
|
|
FINISHED |
|
|
|
|
|
|
SEE FITTING WALL |
|
|
|
|
|
|
SPECS FOR |
|
|
|
|
|
16 |
DIMENSIONS |
|
|
|
|
|
|
|
|
|
|
|
(406mm) |
|
|
|
|
|
|
|
|
|
9 |
|
|
|
|
|
|
(229 mm) |
|
|
|
|
|
32 |
|
|
|
PUMP |
|
ON/OFF |
|
|
|
|
|
SWITCH |
|
(813mm) |
CUTOUT IN FLOOR FOR DRAIN |
|
|
|||
|
|
|
||||
|
|
|
|
|||
C/L OF |
3 |
|
(2) AIR VALVES |
ACCESS TO PUMP/MOTOR |
||
SUPPLIES |
(76mm) |
|
|
|
THROUGH REMOVABLE |
|
|
|
|
|
|
FRONT ACCESS PANEL |
|
|
C/L OF DRAIN |
|
|
C/L OF |
|
|
|
|
|
|
SHOWER ARM |
|
|
|
|
|
|
FINISHED |
|
|
OPTIONAL TO |
|
IN-LINE HEATER |
WALL |
|
||
FINISHED FLOOR |
|
|
|
|
||
USUALLY BETWEEN |
1" WATER |
REMOVABLE |
C/L OF |
|
||
65 & 78 |
RETENTION |
BLANK |
|
VALVES |
|
|
(1651 & 1981mm) |
FLANGE |
|
|
|
|
|
|
(3 SIDES) |
12 |
|
C/L OF |
|
|
|
C/L OF |
|
|
|||
|
(305mm) |
|
SPOUT |
|
||
|
OVERFLOW |
OPT. |
4 |
|
TILING |
|
|
3-1/2 |
|
LEVELING STRINGER |
|||
|
|
|
||||
|
|
(102 mm) |
FLANGE |
NOT FOR SUPPORT |
||
|
(89mm) |
|
||||
|
|
|
|
|
|
|
TOP OF |
|
|
|
UNDERSIDE |
DECK |
21-1/2 |
|
21-1/4 |
OF DECK |
|
(546mm) |
|
(540mm) |
|
|
|
REF. |
|
|
|
|
|
|
|
|
ROUGH |
|
DIM |
|
|
|
|
|
|
|
FLOOR |
|
|
|
|
BATH |
1-1/2 N.P.T.M. |
|
|
|
SUPPORT |
THREADS |
2-3/4 |
|
|
MATERIAL |
1-1/2 O.D.TAILPIECE |
(70mm) |
|
|
|
4-5/8 |
|
|
|
|
|
|
|
|
|
|
(117mm) |
|
Left-hand version shown
GENERAL SPECIFICATIONS FOR 2425E WHIRLPOOL
INSTALLED SIZE |
|
|
|
|
60 x 32 x 21-1/2 (1524 x 813 x 546mm) |
|||||||||||||||||
|
|
|
|
|||||||||||||||||||
WEIGHT |
|
|
|
|
|
|
|
|
|
|
|
|
115 Lbs. (52 Kg.) |
|||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|||||||||||
WEIGHT w/WATER |
|
|
|
|
|
|
|
|
|
|
574 Lbs. (258 Kg.) |
|||||||||||
GAL. TO OVERFLOW |
|
|
|
|
|
|
|
|
|
|
|
55 Gal. (208 L.) |
||||||||||
WHIRLPOOL MIN. OPERATING VOL. |
|
|
|
|
|
45 Gal. (171 L.) |
||||||||||||||||
|
|
|
|
|
||||||||||||||||||
BATHING WELL AT SUMP |
|
|
|
|
|
16-1/4 x 38-1/4 (413 x 972mm) |
||||||||||||||||
|
|
|
|
|
||||||||||||||||||
BATHING WELL AT RIM |
|
|
|
|
26-1/4 x 52-1/2 (667 x 1334mm) |
|||||||||||||||||
|
|
|
|
|||||||||||||||||||
WATER DEPTH TO OVERFLOW |
|
|
|
|
|
|
|
15 (381mm) |
||||||||||||||
|
|
|
|
|
|
|
||||||||||||||||
FLOOR LOADING |
|
|
|
|
|
43 Lbs./Sq.Ft. (208 Kgs./Sq.m) |
||||||||||||||||
|
|
|
|
|
||||||||||||||||||
(PROJECTED AREA) |
|
|
|
|
|
|
|
|
|
|
|
|
||||||||||
PTS. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
20.8 |
||||||
CUBE (FT3) |
|
|
|
|
|
35.3 |
||||||||||||||||
|
|
|
|
|
||||||||||||||||||
|
|
|
WHIRLPOOL ELECTRICAL SPECIFICATIONS |
|||||||||||||||||||
PUMP |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
1.6 HP, 9.7 AMPS,120V. |
|||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||||
THANK YOU...
for selecting an American Standard bath. Your new bath is shipped to you after careful inspection. the whirlpool version is completely assembled with pump, motor, and system piping. All you need to finish the installation are your selected fittings and electrical connections for a whirlpool. To insure maximum performance and pleasure from this
product, please follow the instructions and cautions.
List of Optional Components (not included):
•Flex-Jet Pulse Jet Kit*
•Flex-Jet Soft Jet Kit*
•E-Z-Install Heater*
List of Required Components (not included):
• |
Drain* |
• Bath Filler* |
|
* see your Home Depot Retailer |
|
||
List of Required Tools and Supplies: |
|||
Tools |
Supplies |
||
• |
Level |
• |
Nails |
• |
Tape Measure |
• |
Putty |
• |
Pipe Wrench |
• |
Caulking (waterproof) |
• |
Slip Joint Pliers |
• |
1 x 3 or 2 x 2 |
• |
Screw Driver |
|
Stringers |
• |
Standard |
• |
Drop Cloth |
|
Woodworking Tools |
• |
15 amp GFI |
• |
Personal Safety |
|
Outlet |
|
Equipment |
• |
Cement, Plaster, |
• |
Caulking Gun |
|
Grout |
General Installation Information
Carefully uncrate and inspect your new bath for any shipping damage. If such damage is found, report it to your vendor immediately. After inspection and during installation, protect the bath from construction damage. Before installation, and before enclosing with wallboard, tile, etc., water test the unit and check for leaks. Do not make modifications to the whirlpool system or remove pump from factory mounting. This could adversely affect the safety and performance of the whirlpool and void the warranty. Do not handle or move the whirlpool by the pump, motor, or piping system. Fittings (bath filler, shower arm, etc.) are not provided with the bath and must be ordered separately. Framing and enclosing materials are provided by others.
General Installation Information |
IMPORTANT: Water test unit before installation and |
|
enclosure! |
||
Bath may only be installed in a recess type installation. |
Locate studs as required. insure rough dimensions are proper, plumb and square. For whirlpools, access to pump/motor may be made through access opening in apron panel. The following procedure must be used for all installations: leveling support stringer should be as indicated. this bath is not self-supporting and must be supported along it's entire bottom. Support with mortar or grout. Position bathtub/whirlpool within the recess, check level, front to back, side to side, and shim as necessary. To secure the tub to wood studs use drywall screws w/washers or roofing nails immediately above the flange of the tub.To secure the tub to steel studs use 4" drywall screws and flatwashers.
See page 2 for complete installation information.
Caution: Take extra care when driving nails or screws to avoid damaging the tub. The tile or similar finished floor will be butted against the bottom of the tub apron, also holding the tub in place.
FOR AFTER-SALES SERVICE CALL 1 (800) 442-1902 WEEKDAYS.
© American Standard Inc. 2002
752876-100 Rev. E All product names listed herein are trademarks
of American Standard Inc. unless otherwise noted.
INSTALLATION AND FRAMING INSTRUCTIONS
Locate studs as required. Ensure roughing-in dimensions are proper, plumb and square. Access to Pump/Motor may be made through the access opening in the apron panel. It is strongly recommended that an additional opening be provided for access to the drain components.
NOTE: The apron may be used as the primary access opening.
1.As shown in Fig. 1, mark the position of the underside of the deck by tracing a line onto the studs, using a level or other suitable straight edge.
2.With the top of the stringer touching the traced line, attach the stringer to the studs.
3.Install drain components to the whirlpool or bath following the manufacturers instructions. See the roughing-in drawing for suggested opening size and location dimensions.
4.THIS BATH MUST BE SUPPORTED ALONG ITS ENTIRE BOTTOM. We recommend the use of mortar as bedding material (sand is not recommended). Apply enough bedding to support the complete bottom of the bath. After the bedding has been poured, and before it sets, position whirlpool or bath within recess until the rim is leveled against the leveling stringers (see "Typical Recess Installation") shown below. The rim of the bath MUST NOT support weight. Allow the bedding material to completey harden before applying weight to the rim or bottom of the bath. Any finish material such as tile or wall board must be self-supporting if it contacts the deck of the bath.
FIG. 1
21-1/4 (540mm)
TYPICAL RECESS INSTALLATION
21-1/4 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2 |
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
(540mm) |
|
|
|
|
|
|
|
|
|
/ |
|
|
|
|
|
|
|
|
|
|
|
|
|
1 |
|
|
) |
|
|
||
|
|
|
|
|
|
|
- |
|
|
|
|
|
|||
|
|
|
|
|
|
|
0 |
|
|
m |
|
|
|||
|
|
|
|
|
3 |
|
|
m |
2 |
|
|||||
|
|
|
|
|
|
|
|
|
5 |
|
|
) |
|||
|
|
|
|
|
|
|
|
7 |
|
|
|
3 |
|
||
|
|
|
|
|
7 |
|
|
|
|
|
m |
||||
|
|
|
|
|
( |
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
m |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
3 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
1 |
WIDTH |
|
|
|
|
|
|
|
|
|
|
|
|
8 |
|
|
||
|
|
|
|
|
|
|
|
|
|
|
( |
|
|
|
|
60-1/8 |
|
|
|
|
|
|
|
|
TUB |
|
|
||||
(1527mm) |
|
|
|
|
|
|
|
|
|
|
|
||||
ALLOW OPEN FRAMING ON PUMP/MOTOR END OF WHIRLPOOL FOR PUMP CLEARANCE
SUGGESTED WHIRLPOOL/BATH INSTALLATION METHOD
WOOD STUDS
STUD |
|
WATERPROOF DRYWALL |
|
OR CEMENT BOARD |
|
TILE |
|
ROOFING NAIL |
|
SEALANT |
|
TUB |
|
|
1 x 3 (25 x 76mm) WOOD |
|
STRINGER FULL LENGTH |
STEEL STUDS |
|
STEEL |
|
STUD |
|
WATERPROOF DRYWALL |
WASHER |
OR CEMENT BOARD |
|
TILE |
|
SEALANT |
|
|
4" (102mm) |
|
DRYWALL |
TUB |
SCREW |
|
|
1 x 3 (25 x 76mm) WOOD
STRINGER FULL LENGTH
752876-100 Rev. E |
(2) |
Loading...