American Standard 2391.202, 2390.202 User Manual

AMERICAST® LIMITED LIFETIME WARRANTY

If an American-Standard Americast® brand product is found to be defective in materials or workmanship, after inspection by an authorized American-Standard representative, American-Standard will repair or, at its option, exchange the product for a similar model. This warranty extends for the lifetime of the product, so long as it remains in use in its original place of installation, except that the warranty applies to a bathing vessel’s slip-resisting surface only for the first year after the product’s initial installation.

This warranty applies only to the original purchaser and installation of these products.

This warranty does not apply to whirlpool components or to faucets, drains, mounting rims, grab bars or other accessories. If manufactured or supplied by American-Standard, such whirlpool components and accessories are covered under separate limited warranties.

This warranty does not apply to local building code compliance. Since local building codes vary considerably, the purchaser of this product should check with a local building or plumbing contractor to assure local code compliance before installation.

This warranty shall be void if the Americast® brand product has been moved from its initial place of installation; if it has been subjected to faulty maintenance, abuse, misuse, accident or other damage; if it was not installed in accordance with AmericanStandard’s instructions; or if it was modified in a manner inconsistent with the product as shipped by American-Standard.

American-Standard's option to repair or exchange the product under this warranty does not cover any labor or other costs of removal or installation, nor shall American-

Standard be responsible for any other incidental or consequential damages attributable to a product defect or to the repair or exchange of a defective product, all of which are expressly excluded from this warranty. (Some states or provinces do not allow the exclusion or limitation of implied warranties, so this exclusion may not apply to you.)

This warranty gives you specific legal rights. You may have other statutory rights that vary from state to state or from province to province, in which case this warranty does not affect such statutory rights.

For service under these warranties, it is suggested that a claim be made through the contractor or dealer from or through whom the product was purchased, or that a service request (including a description of the product model and of the defect) be sent to the following address:

In the United States:

AMERICAN STANDARD, INC. P.O. Box 6820

Piscataway, New Jersey 08855

Attn: Director of Consumer Affairs

For residents of the United States, warranty information may also be obtained by calling the following toll free number: [phone]

In Canada:

AMERICAN STANDARD, INC.

2480 Stanfield Road

Mississauga, Ontario Canada L4Y 1S2 Toll Free: [phone]

In Mexico:

IDEAL STANDARD, S.A. de C.V Customer Service Manager

Planta Santa Clara,Via Morelos #330

Santa Clara Coatitla Ecatepec de Morelos 55540, Estado de Mexico, Mexico

© American Standard Inc. 2002

Princeton™ Bath	2390.202	2391.202
	2392.202	2393.202

Installation Instructions

Observe Local Plumbing and Building Codes

Introduction: Thank you for selecting American-Standard...products which have been the benchmarks of fine quality for over 100 years. To help insure that the installation process will proceed smoothly, please read these instructions

carefully before you begin. Also carefully unpack and examine your new plumbing fixture.

1 FRAMING INSTRUCTIONS

Note recess is 1527 x 813mm (60-1/8 x 32). Cut a 229 x 305mm (9 x 12) hole in sub floor for drain, centered 362mm (14-1/4) as shown for below floor rough. Locate studs as required, then ensure rough opening dimensions are proper and supports are plumb and square.

*Install stringer as shown (346mm [13-5/8] for through the floor drain or

435mm [17-1/8] for above the floor drain.)

813mm

(32)

LEVELING SUPPORT STRINGER 51 x 102mm (2 X 4)

229 x 305mm (9 x 12) FLOOR CUTOUT FOR DRAIN

*

	762mm
	WIDTH
	(30)
362mm	TUB
-1/4)
(14
1527mm
(60-1/8)

790043-400 (Rev. G )

2 DRAIN	STANDARD
	AMERICAN

Install the overflow and drain assembly onto the tub per manufacturer's instructions.

3 Position bathtub within the recess, check level, front to back, side to side. Also check drain clearance hole in sub floor. To secure the tub to wood studs, use roofing nails immediately above the flange of the tub.

To secure the tub to steel studs, use drywall screws and flat washers. (See Step 4)

Caution: Take Extra Care When Driving Nails or Screws To Avoid Damaging The Tub. The tile or similar finished floor will be butted against the bottom of the tub apron also holding the tub in place.

UNDERLAYMENT

FINISHED TILE FLOOR

NAIL

OR

DRYWALL

SCREW

EVERY STUD

SUB FLOOR

4	Below is shown typical cross sections of the tub rim showing
	typical wall constructions.
	WOOD STUDS	STEEL STUDS
	STUD	STEEL
	SHIM
		STUD
	DRY WALL	SHIM	WASHER
	TILE
		DRY WALL
	ROOFING NAIL	TILE
	SEALANT	SEALANT
			4" (102mm)
			DRYWALL
		TUB	SCREW
	TUB

51 x 102mm (2 x 4) WOOD

STRINGER FULL LENGTH

FINISHED

WALL

23mm		64mm	229 x 305mm
			9" X 12" HOLE IN SUB FLOOR
15/16"		2-1/2"	FOR BELOW FLOOR ROUGH

*					60mm	19mm
					2-3/8"
						3/4"
			356mm
64mm
			14"	19mm
2-1/2"
	DIA.			3/4"	197mm
					7-3/4"
ROUGH					STD. 1-1/2
					DRAIN OUTLET
FLOOR
BELOW FLOOR ROUGH
2390.202	2391.202					FINISHED
			1524mm			WALL
				60"	89mm
					3-1/2"	48mm
						1-7/8"
					FULL LENGTH
					SUPPORT STRINGER
			FINISHED
23mm		64mm	WALL
15/16"		2-1/2"
*
349mm	64mm		445mm			362mm
						14-1/4"
13-3/4"	2-1/2"		17-1/2"		762mm
	DIA.				30"
ROUGH
FLOOR

ABOVE FLOOR ROUGH 2392.202 2393.202

*PLUMBER NOTE: PROVIDE FULL LENGTH SUPPORT STRINGER AT THIS POINT

LEFT HAND TUB ILLUSTRATED

RIGHT HAND TUB IS REVERSED

790043-400 (Rev. G)