American Standard MONTERREY 6542.145, MONTERREY 6540.17, MONTERREY 6542.14, MONTERREY 6542.175, MONTERREY 6542.17, MONTERREY 6540.175, MONTERREY 6540.14 User Manual

Size:
126.46 Kb
Download
6540.140
6540.170
6542.140
6542.170
6542.145
6540.175
6542.175

Installation

Instructions

SPREAD LAVATORY

FAUCETS

Thank you for selecting American-Standard...

the benchmark of fine quality for over 100 years.

To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin.

Certified to comply with ANSI A112.18.1M M968508 REV.1.3

Recommended tools

Screwdriver

Channel Locks

Adjustable Wrench

Tubing Cutter

1

 

 

 

SPOUT OR BASE ASSEMBLY

CAUTION

Turn off water at

 

main supply.

 

 

 

 

Insert SPOUT SHANK (1) through center hole of mounting surface, making sure RUBBER GASKET(2) is properly positioned in SPOUT BASE(3).

Assemble RUBBER WASHER (4), BRASS WASHER(5), and LOCKNUT(6) onto threads of SPOUT SHANK(1) from underside of mounting surface.

Align SPOUT (7) and tighten LOCKNUT(6). Be sure slot in BRASS WASHER(5) is positioned to the rear as shown.

7

32

1

1a TO CHANGE SPOUT TO A SWIVEL SPOUT:

Unscrew SPOUT NUT (8) and remove SPOUT(7).

Take SPOUT CLIP (9) off SPOUT(7) and remove RUBBER RING(10).

Replace RUBBER RING (10) with seperate PLASTIC RING(11) packed with faucet.

Put SPOUT CLIP (9) on SPOUT (7).

Reassemble SPOUT (7) to SPOUT BASE(3).

7

8

10

9

311

4

5

6

M968508 REV.1.3

2 VALVE ASSEMBLY

Install LOCKNUTS (1), BRASS WASHERS(2) and RUBBER WASHERS(3) onto valve shanks.

Push TUBING (4) ends into VALVE(5) side outlets. Insert VALVES(5) into mounting holes from underside of ledge.

Press TEE (6) onto SPOUT SHANK(7) making certain that theO-RING(8) is properly seated on SHANK(7). Push COUPLING(9) into TEE(6) and attach to SPOUT SHANK(7) and tighten.

Place RUBBER RING (11) into DECK ADAPTERS(10) and thread onto valves until snug against internal stop.

Tighten LOCKNUT (1) to secure VALVE(5) position.

Slide FERRULE (13) and COUPLING NUT(14) to outlet of VALVE(5) and tighten COUPLING NUT(14) firmly.

Connect HOT water supply to inlet of left VALVE and COLD water supply to inlet of right VALVE using appropriate connector.

11

10

 

5/16'' MIN. 5

MOUNTING SURFACE

3

2

1

10

11

10

 

 

11

 

3

 

MOUNTING

 

 

 

LEDGE

 

 

5

8

 

 

 

 

2

13

7

 

 

 

1

14

 

 

HOT

 

14

5

 

 

13

 

6

 

4

 

 

9

 

 

 

 

 

 

 

 

 

 

 

COLD

3 DRAIN ASSEMBLY (6542.140/.170)

1

4 INSTALL HANDLES

7

 

6

 

 

PUTTY

 

 

2

 

Apply a bead of PUTTY around underside

 

 

Turn VALVES (1) to off position.

 

of DRAIN FLANGE (1) flange. Insert DRAIN

 

SINK

Insert ADAPTOR (8) with larger diameter

 

PLUG (2) into SINK drain hole.

 

 

 

Hold DRAIN PLUG (2) to prevent turning and

 

2

over the VALVE STEM (4).

7

 

3

Align LEVER (2) or WRIST BLADE

 

assemble GASKET (3), WASHER(4), and

 

5

 

 

HANDLE (3) and install onto VALVE

 

LOCKNUT (5) from underneath sink.

4

 

STEM (4).

3

 

Apply sealant to threaded end of TAILPIECE

 

 

 

 

 

Insert BLUE INDEX (5) into

8

 

and thread into lower end of DRAIN PLUG.

5

 

 

 

cold valve (right side) and red

4

 

Connect other end to trap.

 

SEALANT

INDEX (6) into hot valve (left

 

 

 

 

side).

1

 

 

 

6

 

Insert HANDLE SCREW (7) into

 

 

 

 

 

 

 

 

 

 

HANDLES and tighten with

 

 

 

 

 

 

screwdriver.

 

5 TEST INSTALLED FAUCET

 

 

 

Operate both handles to flush water lines thoroughly. Check

 

 

 

spout mounting and hose connections for leaks.

 

Remove AERATOR.

 

 

 

Turn handles into OFF position and replace AERATOR.

 

With handle in OFF position, turn on water supplies and check

 

 

 

all connections for leaks.

 

 

 

 

 

6

SERVICE

STOP

90°

 

If spout drips, operate handles several times from OFF to ON

 

 

 

WASHER

 

 

position. Do not force - handles turn only 90°.

 

To change direction of handle rotation,

 

SPRING

Plastic SCREEN in CARTRIDGE may accumulate

 

proceed as follows:

 

 

 

 

 

dirt causing reduced water flow. To clean, first

 

 

 

 

CLIP

 

Turn valve to OFF position.

 

 

turn off hot and cold water supplies, then:

 

 

Remove HANDLE and BONNET NUT.

 

 

Remove HANDLE and BONNET NUT.

CARTRIDGE

 

Remove SPRING CLIP.

 

 

 

Remove CARTRIDGE by pulling up.

 

 

 

 

 

 

Lift STOP WASHER, turn 90° and replace.

 

 

Thoroughly rinse plastic SCREEN at

 

 

Replace SPRING CLIP.

 

 

 

base of CARTRIDGE.

 

 

Replace BONNET NUT, HANDLE, SCREW,

 

 

 

 

 

and INDEX.

 

 

 

Replace CARTRIDGE until flange is

 

 

AERATOR may accumulate dirt causing distorted and reduced

 

tight against valve body.

 

 

 

Turn valves OFF.

 

 

water flow. Remove AERATOR and rinse clean.

 

 

 

 

 

 

Replace BONNET NUT, HANDLE, SCREW

 

 

 

 

 

 

 

 

 

 

and INDEX.

SCREEN

CARE INSTRUCTIONS:

DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.

DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A CLOTH WITH A COARSE SURFACE.