INSTALLATION INSTRUCTIONS
For Two-Piece Toilets with 
™ 2000
Repertoire 2266/2280 |
Ellisse 2184 |
Cadet 2798/2898 |
Heritage 2176 |
Infinity 2316/2319 |
Reminiscence 2311 |
Antiquity 2262/2264 |
Cascada 2321/2323 |
Cadet Specifier 2783/2883 |
Thank you for selecting American Standard - the benchmark of fine quality for over 100 years. To ensure this product is installed properly, please read these instructions carefully before you begin. (Certain installations may require professional help.) Also be sure your installation conforms to local codes.
! CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!
NOTE: Pictures may not exactly define contour of china and components.
RECOMMENDED TOOLS AND MATERIALS
Putty Knife |
Regular Screwdriver |
Adjustable Wrench |
Sealant |
Tape Measure |
Hacksaw |
Wax Ring/Gasket |
Flexible Supply Tube |
Closet Bolts |
Carpenters Level |
1REMOVE OLD TOILET
a.Close toilet supply valve and flush tank completely. Towel or sponge remaining water from tank and bowl.
b.Disconnect and remove supply line. NOTE: If replacing valve, first shut off main water supply!
c.Remove old mounting hardware, remove toilet and plug floor waste opening to prevent escaping sewer gases.
d.Remove closet bolts from flange and clean away old wax, putty, etc. from base area. NOTE: Mounting surface must be clean and level before new toilet is installed!
2 |
|
ROUGHING-IN DIMENSIONS: |
3 |
|
|
|
NOTE: Distance from wall to closet flange centerline must |
|
|
|
|
|
|
|
|
|
be as listed below: |
|
CLOSET FLANGE |
|
|
For 4110 Tanks: A = 254mm (10") |
|
|
|
|
|
|
|
|
FINISHED WALL |
For 4114 Tanks: A = 356mm (14") |
|
|
|
|
For all other Tanks: A = 305mm (12") |
|
|
A
|
|
CLOSET BOLTS |
|
SUPPLY |
|
|
AS |
|
|
REQ'D. |
|
|
|
INSTALL CLOSET BOLTS |
A |
FLOOR |
Install closet bolts in flange channel, turn 90°, and slide |
into place 6" (152 mm) apart and parallel to wall. |
||
|
FINISHED |
|
4 |
|
5 |
SEALANT |
WAX RING |
|
|
NUT |
|
|
|
|
|
|
TAPERED |
|
|
WASHER |
|
|
CLOSET |
|
|
BOLT |
|
|
FLANGE |
INSTALL WAX SEAL |
|
POSITION TOILET ON FLANGE |
Invert toilet on floor (cushion to prevent damage), and |
a. Unplug floor waste opening and install toilet on closet flange so bolts project |
|
install wax ring evenly around waste flange (horn), with |
through mounting holes. |
|
tapered end of ring facing toilet. Apply a thin bead of |
b. Loosely install retainer washers and nuts. Side of washers marked "THIS |
|
sealant around toilet base. |
|
SIDE UP" must face up! |
S A V E F O R F U T U R E U S E
Saniwares
P r o d u c t n a m e s l i s t e d h e r e i n a r e t r a d e m a r k s o f A m e r i c a n S t a n d a r d I n c . © A m e r i c a n S t a n d a r d I n c . 1 9 9 9
730451-100 Rev. A
6
BOLT CAP
CLOSET FLANGE
CLOSET BOLT
WASHER NUT
INSTALL TOILET
a. Position toilet squarely to wall and, with a rocking motion, press bowl down fully on wax ring and flange. Alternately tighten nuts until toilet is firmly seated on floor.
! CAUTION:
DO NOT OVERTIGHTEN NUTS OR BASE MAY BE DAMAGED!
b.Install caps on washers. (If necessary, cut bolt height to size before installing caps.)
c.Smooth off the bead of sealant around base. Remove excess sealant.
7a
For Tanks/Bowls using Speed Connect System (Tank mounting bolts pre-installed).
TANK MTG. |
RUBBER |
|
GASKET |
||
BOLTS PRE- |
||
|
||
INSTALLED |
|
WASHER
NUT
INSTALL TANK
a.Install large rubber gasket over threaded outlet on bottom of tank and lower tank onto bowl so that tapered end of gasket fits evenly into bowl water inlet opening, and tank mounting bolts go through mounting holes. Secure with metal washers and nuts.
b.With tank parallel to wall, alternately tighten nuts until tank is snugged down evenly against bowl surface.
! CAUTION:
DO NOT OVERTIGHTEN NUTS MORE THAN REQUIRED FOR A SNUG FIT!
7b
For all other Tanks/Bowls
RUBBER
WASHER
RUBBER TANK MTG. 
GASKET
BOLTS
WASHER
NUT
INSTALL TANK
a.Install large rubber gasket over threaded outlet on bottom of tank and lower tank onto bowl so that tapered end of gasket fits evenly into bowl water inlet opening.
b.Insert tank mounting bolts and rubber washers from inside tank, through mounting holes, and secure with metal washers and nuts.
c.With tank parallel to wall, alternately tighten nuts until tank is snugged down evenly against bowl surface.
! CAUTION:
DO NOT OVERTIGHTEN NUTS MORE THAN REQUIRED FOR A SNUG FIT!
8 |
INSTALL TOILET SEAT Install toilet seat in accordance with manufacturer's directions. |
|
9 |
TANK |
|
WATER INLET |
|
|
WASHER |
|
|
COUPLING NUT |
FLEXIBLE |
|
SUPPLY |
||
|
||
|
VALVE NUT |
|
|
COMPRESSION |
|
|
COLLAR |
|
TRIM |
|
|
PLATE |
|
|
VALVE |
|
CONNECT WATER SUPPLY |
10 |
OVERFLOW TUBE |
|
TRIP LEVER |
|
||
|
|
|
|
a. |
Connect water supply line between |
|
REFILL TUBE |
|
shutoff valve and tank water |
|
|
|
inlet fitting. Tighten coupling nuts |
|
|
|
securely. Check that refill tube is |
|
Fig. 10A |
|
inserted into overflow tube. |
WATER CONTROL |
|
|
|
ASSEMBLY |
|
b. |
Turn on supply valve and allow |
|
|
|
tank to fill until water rises to |
WATER LINE LEVEL |
|
|
shutoff position. |
|
|
|
|
FLUSH VALVE |
|
|
|
|
|
|
|
|
FLOAT |
c. |
Check for leakage at fittings, |
|
FLAPPER |
|
ASSEMBLY |
||
|
tighten or correct as needed. |
|
|
|
|
|
|
|
|
WATER INLET |
FLUSH VALVE |
|
|
|
|
ADJUSTMENTS
a.Adjust water level. Water level should be adjusted to level indicated on tank by adjusting valve height.
See Step 11 for valve height adjustment method
b.If bowl fails to siphon, an adjustment may be required with the lift chain. Simply remove the bead chain from the retainment clip (see Fig. 10A) and take up slack on the chain, and reinsert on lift rod. Make sure the chain is not too taught.
TOILET REQUIRES THAT THE TANK REFILLS IN NO LESS THAN ONE MINUTE. ADJUST WATER SUPPLY VALVE (FIG. 9) ACCORDINGLY.
- 2 - |
730451-100 Rev. A |
Loading...