American Standard 4 2023, 4 2443, 4 2627, 4 2074, 4 2367 User Manual

...
0 (0)

INSTALLATION INSTRUCTIONS

CARE AND MAINTENANCE

Champion® 4 2-piece Toilets

Models - 2002, 2018, 2023, 2414, 2585, 2792, 2586, 2793, 3186, 3404

Doral ClassicChampion® 4 2-piece Toilets Models - 2058, 2074, 2076, 2473

Doral ClassicChampion® 4 2-piece Toilets

Models - 2367, 2368, 2369, 2443

OakmontChampion® 4 2-piece Toilets

Models - 2625, 2627, 2738

TownsendChampion® 4 2-piece Toilets

Models - 2733, 2735

Thank you for selecting American Standard - the benchmark of fine quality for over 100 years.To ensure this product is installed properly, please read these instructions carefully before you begin. (Certain installations may require professional help.) Also be sure your installation conforms to local codes.

!CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!

NOTE: Pictures may not exactly define contour of china and components.

NOTE: BACK-TO-BACK INSTALLATION

Depending upon your plumbing and venting conditions, the flow from the Champion in a back-to-back installation may create a vacuum on the system and draw water from the opposing bowl. The National Standards Plumbing Code prohibits the use of a cross fitting for drainage as throw over is possible. The code does approve a directional "Y" style fitting with proper venting to direct the water downward and away from the other toilet.

Recommended fitting type for back-to-back installations.

RECOMMENDED TOOLS AND MATERIALS

Putty Knife

Regular Screwdriver

Adjustable Wrench

Sealant

Hacksaw

Wax Ring/Gasket

Flexible Supply Tube

1/2" Deep Well Nut Driver or

Closet Bolts

Tape Measure

Carpenters Level

Deep Well Socket Wrench

1REMOVE OLD TOILET

a.Close toilet supply valve and flush tank completely. Towel or sponge remaining water from tank and bowl.

b.Disconnect and remove supply line. NOTE: If replacing valve, first shut off main water supply!

c.Remove old mounting hardware, remove toilet and plug floor waste opening to prevent escaping sewer gases.

d.Remove closet bolts from flange and clean away old wax, putty, etc. from base area. NOTE: Mounting surface must be clean and level before new toilet is installed!

P r o d u c t n a m e s l i s t e d h e r e i n a r e t r a d e m a r k s o f A S A m e r i c a , I n c .

730529-100 Rev. U

© A S A m e r i c a , I n c . 2 011

 

S A V E F O R F U T U R E U S E

American Standard 4 2023, 4 2443, 4 2627, 4 2074, 4 2367 User Manual

2 NOTE: DRAWINGS ARE FOR DIMENSIONAL PURPOSES ONLY. THEY ARE NOT EXACT REPRESENTATIONS.

ROUGHING-IN DIMENSIONS: Right HeightElongated Two Piece Toilet

ROUGHING-IN DIMENSIONS: Normal Height Elongated Two Piece Toilet

FINISHED WALL

Right HeightRound Front Two Piece Toilet

FINISHED WALL

Normal Height Round Front Two Piece Toilet

772mm

 

 

 

 

 

 

772mm

 

 

 

(30-3/8")

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(30-3/8")

 

 

 

* 721mm

 

 

 

*

 

 

 

 

 

 

 

721mm

 

 

 

 

 

(28-3/8")

 

 

 

 

 

 

 

 

19mm ± 6mm

 

 

D

 

(28-3/8")

 

 

 

 

(1 ± 1/4")

 

 

 

19mm ± 6mm

 

 

 

 

 

 

 

 

 

 

D

 

 

 

 

 

 

(1 ± 1/4")

 

 

 

A

 

 

 

 

 

 

 

 

 

 

 

 

 

A

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

470mm

 

 

 

 

470mm

 

 

 

 

(18-1/2")

 

 

 

 

(18-1/2")

 

 

 

 

 

 

356mm

 

 

 

* 419mm

 

 

 

 

* 419mm

 

 

 

 

(16-1/2")

 

356mm

 

 

 

(14")

 

 

 

 

 

 

 

 

 

 

 

 

(14")

 

 

(16-1/2")

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SUPPLY

E

 

 

 

SUPPLY

 

E

 

 

 

 

 

 

 

 

 

 

 

 

AS

 

 

 

 

AS

 

 

83mm (3-1/4")

 

 

REQ'D

83mm (3-1/4")

 

 

 

REQ'D

 

 

 

419mm

 

 

 

 

387mm

 

 

 

(16-1/2")

 

 

 

 

(15-1/4")

 

 

 

 

254mm

 

 

 

254mm

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(10")

 

 

 

 

 

(10")

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

16mm

 

 

152mm

 

 

 

16mm

152mm

 

 

 

 

 

 

 

(5/8")

(6")

 

 

(5/8")

 

 

(6")

 

B

C

FINISHED

 

 

B

C

 

 

 

F

* ROUND FRONT

FINISHED

 

 

 

 

 

FLOOR

305mm

 

F

305mm

 

 

 

FLOOR

 

 

 

 

MODELS

 

 

(12")

 

 

 

 

(12")

 

 

 

 

 

 

 

 

 

 

 

 

 

DIMENSIONS

 

 

 

 

 

MODEL

 

A

B

C

 

 

D

E

 

F

2002, 2414, 2586,

 

235mm (9-1/4)

264mm (10-3/8)

362mm (14-1/4)

464mm (18-1/4)

825mm (32-1/2)

254mm (10)

2793, 3186, 3404

 

2018, 2023, 2585, 2792

235mm (9-1/4)

264mm (10-3/8)

362mm (14-1/4)

464mm (18-1/4)

797mm (31-3/8)

254mm (10)

2058

 

216mm (8-1/2)

264mm (10-3/8)

362mm (14-1/4)

479mm (18-7/8)

873mm (34-3/8)

254mm (10)

2074, 2076

 

216mm (8-1/2)

264mm (10-3/8)

362mm (14-1/4)

479mm (18-7/8)

851mm (33-1/2)

254mm (10)

2367

 

216mm (8-1/2)

264mm (10-3/8)

362mm (14-1/4)

492mm (19-3/8)

872mm (34-5/16)

254mm (10)

2368, 2369

 

216mm (8-1/2)

264mm (10-3/8)

362mm (14-1/4)

492mm (19-3/8)

844mm (33-1/4)

254mm (10)

2625, 2627

 

216mm (8-1/2)

273mm (10-3/4)

381mm (15)

492mm (19-3/8)

844mm (33-1/4)

286mm (11-1/4)

2738

 

216mm (8-1/2)

275mm (10-13/16)

384mm (15-1/8)

492mm (19-3/8)

872mm (34-5/16)

295mm (11-5/8)

2733, 2735

 

216mm (8-1/2)

267mm (10-1/2)

379mm (14-7/8)

479mm (18-7/8)

873mm (34-3/8)

284mm (11-3/16)

3

 

 

 

4

 

 

 

 

 

 

 

CLOSET FLANGE

 

 

 

 

SEALANT

WAX RING

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

A

 

 

 

 

 

 

 

CLOSET BOLTS

 

 

 

 

 

 

 

 

 

INSTALL CLOSET BOLTS

INSTALL WAX SEAL

Invert toilet on floor (cushion to prevent damage), and install wax

Install closet bolts in flange channel, turn 90°, and slide into

ring evenly around waste flange, with tapered end of ring facing

place 6" (152 mm) apart and parallel to wall.

toilet. Apply a thin bead of sealant around toilet base.

5 MANIFOLD INSIDE WATERWAY – DO NOT REMOVE

NUT

TAPERED

WASHER

CLOSET

BOLT

FLANGE

POSITION TOILET ON FLANGE

a.Unplug floor waste opening and install toilet on closet flange so bolts project through mounting holes.

b.Loosely install retainer washers and nuts. Side of washers marked "THIS SIDE UP" must face up!

- 2 -

730529-100 Rev. U

Loading...
+ 3 hidden pages