INSTALLATION INSTRUCTIONS
ANTIQUITY CADET® 3 - 1.6 GPF ONE-PIECE TOILET, MODEL 2907 COMPACT CADET® 3 - 1.6 GPF ONE-PIECE TOILET
COMPACT CADET® 3 FloWise™ - 1.28 GPF ONE-PIECE TOILET
Model 2568 – Compact Elongated Right Height™ with Seat
Thank you for selecting American Standard – the benchmark of fine quality for over 100 years. To ensure this product is installed properly, please read these instructions carefully before you begin. (Certain installations may require professional help.) Also be sure your installation conforms to local codes.
!CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!
NOTE: Pictures may not exactly define contour of china and components.
RECOMMENDED TOOLS AND MATERIALS
Putty Knife |
Regular Screwdriver |
Adjustable Wrench |
Sealant |
Tape Measure |
Hacksaw |
Wax Ring/Gasket |
Flexible Supply Tube |
Closet Bolts |
Carpenters Level |
1REMOVE OLD TOILET
a.Close toilet supply valve and flush tank completely. Towel or sponge remaining water from tank and bowl.
b.Disconnect and remove supply line. NOTE: If replacing valve, first shut off main water supply!
c.Remove old mounting hardware, remove toilet and plug floor waste opening to prevent escaping sewer gases.
d.Remove closet bolts from flange and clean away old wax, putty, etc. from base area. NOTE: Mounting surface must be clean and level before new toilet is installed!
2 ROUGHING-IN DIMENSIONS NOTE: Distance from wall to closet flange centerline must be as listed below:
12.7mm |
(1/2") |
83mm (3-1/4")
ANTIQUITY CADET 3
FINISHED WALL
225mm
(8-7/8")
737mm
(29")
C/L OF SEAT POST HOLES 140mm (5-1/2) CENTERS
462mm (18-3/16)
419mm (16-1/2)
235mm |
|
360mm |
|
(9-1/4) |
|
(14-3/16) |
|
305mm |
|
C/L OF OUTLET |
(12") |
|
|
|
|
457mm
(18")
C/L
|
|
714mm |
|
|
|
(28-1/8") |
|
127mm |
|
|
|
(5") |
|
|
|
C/L OF SUPPLY |
276mm |
FINISHED |
|
AS REQUIRED |
(10-7/8) |
||
FLOOR |
|||
|
|
|
COMPACT CADET 3 |
FINISHED WALL |
|
|
724mm |
16 ± 6mm |
(28-1/2) |
381mm |
|
(5/8 ± 1/4) |
(15) |
|
159mm |
|
(6-1/4) |
|
C/L OF SEAT |
|
POST HOLES |
|
140mm (5-1/2) |
|
CENTERS |
79mm (3-1/8)
267mm (10-1/2)
305mm 
(12)
422mm |
|
|
|
|
(16-5/8) |
|
|
|
|
419mm |
|
|
|
724mm |
|
SUPPLY |
|
(28-1/2) |
|
(16-1/2) |
|
|
|
|
|
|
AS |
|
|
|
|
REQ'D |
|
|
292mm |
140mm |
241mm |
|
|
(11-1/2) |
* |
(5-1/2) |
(9-1/2) |
FINISHED |
C/L OF OUTLET |
|
|
|
FLOOR |
|
|
394mm |
|
|
|
|
|
(15-1/2) |
|
3 |
|
4 |
|
CLOSET FLANGE |
|
A
CLOSET BOLTS 
INSTALL CLOSET BOLTS
Install closet bolts in flange channel, turn 90°, and slide into place 6" (152 mm) apart and parallel to wall.
WAX RING
SEALANT
INSTALL WAX SEAL
Invert toilet on floor (cushion to prevent damage), and install wax ring evenly around waste flange (horn), with tapered end of ring facing toilet. Apply a thin bead of sealant around toilet base.
S A V E F O R F U T U R E U S E
P r o d u c t n a m e s l i s t e d h e r e i n a r e t r a d e m a r k s o f A S A m e r i c a , I n c . © A S A m e r i c a , I n c . 2 0 0 9
7301270-100 Rev. D
5 POSITION TOILET ON FLANGE |
6 |
INSTALL TOILET |
|
|
a. Position toilet squarely to wall and, with a rocking |
a. Unplug floor waste opening and install toilet on closet |
|
motion, press bowl down fully on wax ring and flange. |
|
Alternately tighten nuts until toilet is firmly seated on floor. |
|
flange so bolts project through mounting holes. |
|
|
|
|
|
|
|
! CAUTION: |
b. Loosely install retainer washers and nuts. Side of |
|
DO NOT OVERTIGHTEN NUTS |
washers marked "THIS SIDE UP" must face up! |
|
OR BASE MAY BE DAMAGED! |
|
|
b. Install caps on washers. (If necessary, cut bolt height to |
|
|
size before installing caps.) |
|
|
c. Smooth off the bead of sealant around base. Remove |
|
|
excess sealant. |
NUT |
|
|
WASHER
THIS SIDEUP
BOLT
BOLT CAP |
|
FLANGE |
|
BOLTS |
CLOSET FLANGE |
7 INSTALL TOILET SEAT Install toilet seat in accordance with manufacturer's directions.
8a |
|
|
|
|
|
|
|
8b |
|
|
Before continuing, determine the type of water supply connecation you have from |
|
|||||||
|
the chart below and use the appropriate assembly parts required to properly |
|
|||||||
|
reconnect the water supply. DO NOT use plumber's putty to seal these fittings. |
|
|||||||
|
METAL/COPPER |
METAL FLANGED |
METAL SPIRAL |
VINYL/BRAIDED |
|
||||
|
FLARED TUBING |
|
TUBING |
TUBING |
CONNECTOR |
|
|||
|
LOCK NUT |
|
LOCK NUT |
|
LOCK NUT |
LOCK NUT |
|
||
|
CONE |
|
EXISTING |
|
EXISTING |
COUPLING |
|
||
|
|
WASHER |
|
|
|||||
|
WASHER |
|
|
CONE |
NUT |
|
|||
|
|
|
|
|
|
||||
|
COUPLING |
|
EXISTING |
|
WASHER |
|
|
|
|
|
|
|
|
|
|
|
|||
|
|
COUPLING |
|
COUPLING |
|
|
|
||
|
NUT |
|
|
|
|
|
|||
|
|
|
NUT |
|
NUT |
|
|
|
|
|
WATER |
|
WATER |
|
WATER |
WATER |
|
||
|
SHUT-OFF |
|
SHUT-OFF |
|
SHUT-OFF |
SHUT-OFF |
|
||
|
These parts must be used as |
|
Use existing |
|
Use existing spiral |
Captive cone |
|
||
|
illustrated to insure water-tight |
coupling nut |
|
cone washer. |
washers already |
|
|||
|
connection. Use of existing |
|
and washer. |
|
Fluidmaster cone |
included. No |
|
||
|
coupling nut may result in |
|
|
|
|
washer may not |
additional washers |
|
|
|
water leakage. Water supply |
|
|
|
|
seal completely on |
needed. |
|
|
|
tube or pipe must extend at |
|
|
|
|
spiral type supply |
|
|
|
|
least 1/2" inside threaded |
|
|
|
|
line. |
|
|
|
|
shank of valve (does not apply |
|
|
|
|
|
|
|
|
|
to flanged tubing). |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||
|
CAUTION: DO NOT USE |
|
|
CAUTION: Overtightening of |
|
|
|||
|
CONE WASHER WITH |
|
|
LOCK NUT or COUPLING NUT |
|
|
|||
|
|
|
could result in breakage and |
|
|
||||
|
PLASTIC SUPPLY LINE. |
|
|
potential flooding. |
|
|
|||
|
|
|
|
|
|
|
|
|
|
With correct washers in place (see Step 8a), tighten COUPLING NUT 1/4 turn beyond hand tight. DO NOT OVERTIGHTEN.
- 2 - |
7301270-100 Rev. D |
Loading...