American Standard Bathroom Faucet User Manual

Size:
316.05 Kb
Download

Speed Connect™ Drain

Troubleshooting Guide

If sink does not hold water even though Stopper is in the “down” position:

• Follow CABLE ADJUSTMENT PROCEDURE.

If Stopper does not raise up fully or sink drains too slowly:

• Follow CABLE ADJUSTMENT PROCEDURE.

If you need to remove the Stopper:

• Follow STOPPER REMOVAL PROCEDURE.

If you would like the ability to remove your Stopper simply by lifting it out of the drain:

Follow STOPPER INSTALLATION PROCEDURE for“Unlocked” mode.

CABLE ADJUSTMENT PROCEDURE

Disconnect the Cable from the Drain by threading the Cable Connector (1) counter-clockwise.Fig. A.

Look at the area on the Drain Body where the Cable was attached and locate the component labeled as “Cam” in the illustration. Fig. B.

Use a small screwdriver to rotate the Cam in the clockwise direction as far as it will go. At this point the Stopper should be in the UP position. Fig. B, C.

Push DOWN on the Lift-Knobto make sure it is fully down.Fig. C.

Re-attachthe Cable to the Drain Body Connection(2) by threading the Cable Connector(1) clockwise onto the Drain Body Connection(2) andhand-tighten.Fig. A.

Fig. A.

 

Fig. B. Fig. C.

DOWN

1

CAM

 

 

 

 

 

RE-ATTACH

 

 

1

DISCONNECT

CAM CAP

STOPPER

 

 

 

 

2

 

 

 

STOPPER REMOVAL PROCEDURE

Disconnect the Cable from the Drain by threading the Cable Connector (1) counter-clockwise.Fig. A.

Look at the area on the Drain Body where the Cable was attached and locate the component labeled as “Cam” and“Cam Cap” in the illustration.Fig. B.

Use fingers or small screwdriver under either side of the Cam Cap to pry it out from the Drain. Fig. D.

Remove the Cam by pulling it straight out while wiggling gently to loosen the Rubber Seal. Fig. E.

The Stopper can now be removed by lifting it out of the Drain. Fig. F.

Fig. D.

Fig. E.

 

REMOVE

 

CAM CAP

Fig. F.

REMOVE CAM

51314 Rev . 1 . 3

5

STOPPER INSTALLATION PROCEDURE

The Stopper can be installed two ways, “Locked” Mode (Stopper cannot be removed) or “Unlock” Mode (Stopper is removable).

Locked Mode:

Look at the Plastic Loop at the bottom of the Stopper and notice

Fig. G.

that the Loop is on one side of the Stopper. Fig. G.

To install the stopper in “Locked” mode, insert the Stopper into

the Drain so that the Plastic Loop is facing toward the rear of the LOGO Sink and the American Standard logo is facing front. Rotate

Stopper slightly if necessary so that the Stopper slides all the way down.Fig. G.

Re-installthe Cam into the Drain, rotating the Cam if necessary

to make sure it is fully inserted. Fig. J. LOOP TOWARD

REAR OF SINK

Re-installthe Cam Cap, making sure the guide teeth are facing

outward. If the Cam Cap does not “snap” into place, then rotate DRAIN the Cam to make sure it is fully inserted.Fig. K.

Re-attachCable. See “CABLE ADJUSTMENT PROCEDURE” in Troubling Shooting Guide to complete installation. Stopper will be in“Locked” mode and not be removable.

Unlocked Mode:

Look at the Plastic Loop at the bottom of the Stopper and notice that the Loop is on one side of the Stopper. Fig. H.

To install the stopper in “Unlocked” mode, insert the Stopper into the Drain so that the Plastic Loop is facing toward the front of the

Sink and the American Standard logo is facing rear. Rotate Stopper slightly if necessary so that the Stopper slides all the way down.

Fig. H.

Re-installthe Cam into the Drain, rotating the Cam if necessary to make sure it is fully inserted.Fig. J.

Re-installthe Cam Cap, making sure the guide teeth are facing outward. If the Cam Cap does not “snap” into place, then rotate the Cam to make sure it is fully inserted.Fig. K.

Locked Mode

(Vandal Proof)

Fig. H.

LOGO

180˚

LOOP TOWARD

FRONT OF SINK

DRAIN

Re-attachCable. See “CABLE ADJUSTMENT PROCEDURE” in “Troublingshooting Guide” to complete installation. Stopper will be in“Unlocked” mode and removable.

Fig. J.

INSTALL CAM

Unlocked Mode

Fig. K.

CAM

INSTALL

CAM CAP

51314 Rev . 1 . 3

6

Single Control Lavatory Faucet

with Pop-upDrain

023529-0070A

MODEL NUMBERS

CARTRIDGE KIT

 

3808.101

M962527-YYY0A

POP-UPROD

 

066124-YYYOA

 

DECORATIVE RING

909719-YYY0A

066070-YYY0A

SPOUT ESCUTCHEON

AERATOR

 

A912699-0070A

060275-YYY0A

RUBBER RING

HANDLE ASSEMBLY

 

030746-0020A

 

HANDLE SCREW KIT

M962541-0070A

A907086-YYY0A

ESCUTCHEON CAP

MOUNTING KIT

 

060277-YYYOA

023527-0070A

ESCUTCHEON KIT

CARTRIDGE SCREWS

 

 

Replace the "YYY" with

 

 

 

appropriate finish code

 

 

066116-YYY0A

CHROME

002

 

DRAIN STOPPER

WHITE

020

 

 

M953450-YYY0A

066117-YYY0A

WHITE/CHROME

025

WHITE/POL. BRASS

028

2" FLANGE KIT

COMPLETE

 

 

 

DRAIN ASSEMBLY

060276-YYY0A

BLACK NICKEL/BRASS MIX (PVD)

062

 

LIFT ROD

 

BLACK SMITH (PVD)

078

 

 

 

072574-0070A

POLISHED BRASS

099

066118-0070A

EXTENSION ROD

SATIN (PVD)/CHROME

221

 

PIVOT ROD KIT

 

 

 

SATIN NICKEL

295

 

 

SATIN BRASS (PVD)

297

 

 

CHROME/POL BRASS

299

070847-0070A

 

 

 

CLIP

 

M952425-YYY0A

 

M961711-0070A

 

DRAIN ASSEMBLY

 

TAILPIECE INSERT

 

 

 

 

070532-0040A

 

 

 

TAILPIECE

 

 

POP-UPDRAIN ASSEMBLY

M919660-0020A

 

 

BEFORE 01/07

6” TAILPIECE

 

 

 

(NOT INCLUDED

 

 

 

WITH FAUCET)

 

HOT LINE FOR HELP

For toll-freeinformation and answers to your questions, call:1-800-442-1902

Weekdays 8:00 a.m. to 6:00 p.m. EST

IN CANADA 1-800-387-0369(TORONTO1-905-306-1093)Weekdays 8:00 a.m. to 7:00 p.m. EST

IN MEXICO 01-800-839-12-00

P r o d u c t n a m e s l i s t e d h e r e i n a r e t r a d e m a r k s o f A m e r i c a n S t a n d a r d I n c . © A S A m e r i c a , I n c . 2 0 0 8

M962544-YYY0A

STOPPER

ASSEMBLY

M952430-0070A

CABLE ASSEMBLY

M962457-YYYOA

FLANGE ASSEMBLY

M922872-0070A

CAM SEAT INSERT

M962430-0070A

CAM ASSEMBLY

M913207-0070A

TAILPIECE INSERT

A919661-0020A

TAILPIECE

M962458-0070A

DRAIN MOUNTING KIT

51314 Rev . 1 . 3

7