American Standard 7038.400 User Manual

Size:
1.43 Mb
Download
• Fewer parts, installs in less time
• Never needs adjustment
• Guaranteed to seal properly the first time, every time.
SpeedConnect Drain*

 

Installation

TROPIC

Instructions

7038.400

Bidet Faucet and Transfer Valve with EverClean™ Finish & SpeedConnect™ Drain

Congratulations on purchasing your American Standard faucet with EverClean finish and Speed Connect drain, two features found only on American Standard faucets.

EverClean Finish

One wipe effortlessly removes spots

Eliminates the need for cleaners and scrubbing

Permanent surface protectant remains beautiful for the life of the faucet

EverClean™ available on: Polished Chrome, Satin Nickel,

Stainless Steel, Polished Brass (or any combination of these finishes)

Certified to comply with ANSI A112.18.1

M 9 6 8 8 9 3

*Your new American Standard faucet is designed to work only with the SpeedConnect drain.

To ensure that your installation proceeds smoothly-pleaseread these instructions carefully before you begin.

Roughing-in

 

 

FINISHED

8 TO 12

 

Required tools

 

Dimensions

TRANSFER VALVE

 

 

 

 

WALL

 

 

 

 

(FOR FLUSHING

 

 

 

 

BIDET OUTLINE

RIM OR SPRAY)

 

 

2-1/4

 

 

 

 

(C)

(H)

 

 

IS SYMBOLIC

7/8 DIA.

Screwdriver

Plumbers' Putty or

DIA.

 

 

 

1-3/16

 

 

 

Caulking

DOUCHE ADJ.1-1/4

 

 

 

 

 

2-1/8

DIA.

 

4-1/4

 

 

SPRAY

TO 2-1/4

DIA.

1-1/4

 

 

 

 

 

 

 

 

 

Phillips Screwdriver

 

 

1-3/8

 

MAX.

 

 

 

3-7/8

 

 

 

FOR GROUND JOINT

 

Channel Locks

DIA.

 

 

 

CONNECTION OR 1/2 "

 

 

 

 

 

 

 

O.D. SLIP (INLETS)

 

 

 

 

 

FINISHED

 

REAR VIEW WITH

 

 

 

5-1/2

FLOOR

 

WALL REMOVED

Adjustable Wrench

 

 

 

 

 

 

 

 

1-1/4O.D. TAILPIECE

 

 

 

Tubing Cutter

1

 

 

Turn off hot and cold water

 

BIDET FAUCET INSTALLATION

CAUTION

 

supplies before beginning.

6

 

 

 

 

 

 

Place RUBBER RING (10) into DECK ADAPTER(4).

Install LOCKNUT (1) and RUBBER WASHER(2) onto VALVE BODIES(3, 3a). From under side of mounting surface, install VALVE BODY(3, 3a) through valve mounting holes. Threads of VALVE BODY(3, 3a) should extent at least 5/16 of a inch above mounting surface top.Fig. A. Thread DECK ADAPTER(4) onto VALVE BODIES(3, 3a) until snug against internal stop. If necessary, adjust LOCKNUT(1).

410

7

BIDET

LEDGE

8

Tighten LOCKNUTS (1) with WRENCH(5) (supplied) to secure VALVE BODIES(3, 3a).

Remove ESCUTCHEON (6), WASHER(7) and UPPER GASKET(8) from TRANSFER VALVE(9). Insert TRANSFER VALVE(9) into the center forward hole of BIDET.

Replace UPPER GASKET (8) and WASHER(7) and ESCUTCHEON(6) until it locks against internal stop. Position the side threaded outlet rearward and secure MOUNTING NUT(11).

Fig. A.

4

10

 

5/16''

MOUNTING

 

 

3

3a

MIN.

 

 

 

SURFACE

2

HOT

 

COLD

 

 

 

 

 

 

 

1

 

 

9

 

2

 

 

 

 

 

 

 

 

 

1

 

5

 

11

3, 3a

 

 

 

 

 

 

 

 

 

 

 

 

2 SPRAY INSTALLATION

Assemble SPRAY BODY (1) to BIDET. Using putty, seal underside

6

of SPRAY BODY FLANGE (2) and secure with NUT(3).

Thread SPRAY HOSE (4) with SEAL WASHER(5) to SPRAY BODY(1). Connect other end of HOSE(4) with SEAL WASHER(6) to side outlet NIPPLE(7) of the TRANSFER VALVE(8).

Thread SPRAY CAP (9) onto SPRAY BODY(1).

8

2

9

 

PUTTY

1

7

3

5

4

4

1

3 POP-UPDRAIN

Remove CLEAR PLASTIC COVER (1).

Remove CARDBOARD SPACER (2) from under DRAINPOP-UP(3).

Tighten TAILPIECE (4) on DRAIN BODY before installing DRAIN BODY.Fig. B.

Fig. A.

Fig. B.

1

 

3

DRAIN

 

BODY

2

4

 

4 REMOVE FLANGE

Thread FLANGE (1) counter-clockwiseand remove FLANGE(1) and FOAM GASKET(2) from drain body.Fig. A.

Thread LOCKNUT (3) clock-wiseto bottom of drain body. Push GASKET(4) down against LOCKNUT(3). Fig. B.

Fig. A.

Fig. B.

1

4

2

3

5

INSTALL DRAIN FROM

6

BELOW FIXTURE

 

From under side of BIDET

 

 

install DRAIN BODY (1) up

4

 

through drain outlet.

 

 

Note: No plumber’s putty

3

 

or caulk is required.

 

 

The CABLE ATTACHMENT

DRAIN

 

POINT (2) must face towards

OUTLET

 

the rear of the BIDET.

1

 

 

 

Install FOAM GASKET (3) and

2

 

FLANGE (4) onto drain body

 

 

 

from above BIDET and tighten

 

 

FLANGE (4) firmly.

 

TIGHTEN LOCKNUT

Tighten LOCKNUT (1) firmly with Adjustable Wrench or Channel Locks.

1

7 FLANGE GASKET

Fig. A.

Fig. B.

1

Check DRAIN FLANGE in BIDET to ensure that WHITE

 

 

3

FOAM GASKET (1) is fully compressed and not visible.

 

 

 

Fig. A.

DRAIN

 

 

POP-UPROD ASSEMBLY

FLANGE

 

 

 

 

SLOTTED

Insert LIFT ROD GUIDE (1) and CABLE CONNECTOR(2)

 

 

MOUNTING

 

 

NUT

through rear hole, making sure SEAL WASHER (3) is

 

 

4

properly seated. Fig. B.

1 WHITE FOAM

ILLUSTRATION

 

GASKET

2

From below slip slot in MOUNTING NUT (4) over CABLE(5).

NOT VISIBLE

SHOWN LESS

 

VALVES

 

Thread NUT (4) onto lift rod guide shank to secure ROD

 

 

 

GUIDE (1) to bidet. Hand tighten only.Fig. B.

 

 

M 9 6 8 8 9 3

 

2

 

 

FLEXIBLE
SUPPLIES
1/2" PIPE
THREAD

8

ATTACH CABLE

Fig. A.

CONNECTOR

 

POP-UPKNOB(1) must be fully

DOWN

 

down. Fig. A.

 

 

Thread CABLE CONNECTOR (1)

 

 

clockwise onto DRAIN BODY

 

 

CONNECTION (2) and hand

 

 

tighten. Fig. B.

 

 

Your new POP-UPDRAIN

 

 

installation is now complete.

 

 

Fig. C.

 

 

Note: Tailpeice onpop-updrain

 

 

is 1-1/4”O.D.Fig. C.

 

Fig. B.

1

2

Fig. C.

1-1/4”O.D.

9 CHECK OPERATION OFPOP-UP

 

5

Operate LIFT KNOB (1) to verify that STOPPER(2)

 

opens and closes.

 

4

Note: If STOPPER(2) does not open and close properly

1

3

then refer to the “troubleshooting section” of these

 

1

instructions.

 

 

 

INSTALL DIVERTER KNOB

 

2

 

 

Push DIVERTER KNOB (1) onto HANDLE ADAPTER(2).

2

 

Push on RING (3) and tighten with SCREW(4).

 

 

Press on KNOB CAP (5).

 

 

Note: Screwdriver gap is for disassembling and should

 

 

point downwards.

 

 

10 TEE AND HOSE CONNECTION

OUTLINE OF BIDET

Insert SEAL (1) into ADAPTER(2) and tighten ADAPTER(2) to

5

 

side of TRANSFER VALVE (3).

6

Install SEAL (4) into coupling nut of TEE(5) and tighten

3

7a

connection to ADAPTER (2).

 

 

Connect HOSE COUPLING NUTS (6) to Hot and Cold valve bodies and securely tighten.

WATER SUPPLY CONNECTION

NOTE: FLEXIBLE SUPPLIES OR BULL-NOSERISERS NOT INCLUDED AND MUST BE PURCHASED SEPARATELY.

Connect water supply to VALVE BODIES (7,7a) with

1/2" IPS FLEXIBLE SUPPLIES (8) or 3/8" O.D.BULL-NOSERISERS(9). Use adjustable wrench to tighten connections. Do not over tighten. Be careful not to kink copper supply when bending. Use tubing cutter to cut to proper length.

Connect HOT water supply to inlet of left SHANK and COLD water supply to right SHANK using sealant, appropriate connectors, and COUPLING NUTS.

Connect 1-1/4”O.D. tailpiece onPOP-UPDRAIN to waste outlet.

 

4

 

 

COUPLING

 

2

 

NUT

 

Front

 

7

6

1

9

 

 

 

 

 

3/8 O.D.

 

 

 

 

BULL-NOSE

 

 

 

 

RISERS

 

 

 

 

COMPRESSION

2

 

 

 

NUT

 

 

 

 

 

 

 

 

FERRULE

COLD

CONNECT TO

WASTE OUTLET

3/8 COMPRESSION HOT CONNECTION

M 9 6 8 8 9 3

3

11 INSTALL HANDLES

Push ADAPTER (1) on VALVE STEM(2), so that the hole of the ADAPTER(1) without a spline is facing up.Fig. A. Tighten STEM SCREW(3) to secure ADAPTER(1).

Find correct position of LEVER HANDLE ASSEMBLY (4) by adjusting male teeth on ADAPTER(1) to female teeth in HANDLE(4).

Thread LEVER HANDLE ASSEMBLY (4) onto DECK ADAPTER(5) until snug against mounting surface.

Fig. A.

SPLINE END DOWN

THREAD ON 4 TO DECK

ADAPTER

TOP

1

3

2

5

12 TEST INSTALLED FITTING

With HANDLES (1) in OFF position, turn on WATER SUPPLIES(2) and check all connections for leaks.

Operate both HANDLES (1) to flush water lines thoroughly.

Rotate TRANSFER VALVE (5) from rim wash to spray several times to check operation.

13 CHECK DRAIN CONNECTIONS

OUTLINE OF BIDET

3

1

Pull up POP-UPKNOB(3) and fill Bidet with water. Check

4

that DRAIN STOPPER (4) makes a good seal and retains

water in Bidet. If STOPPER (4) does not seal properly, please refer to “Troubleshooting Guide” in these instructions.

Push POP-UPKNOB(3) down and check all drain connections and "P" trap for leaks. Tighten

if necessary.

2

1

2

SPRAY

14 EverClean™ Finish

Care Instructions

American Standard’s EverClean finish will wipe clean with a soft, dry cloth.

A soft cloth with clean water may also be used, if desired. No additional cleaning products are required.

DO NOT USE: Soaps, acid, polish, abrasives, harsh cleaners, or a cloth with a coarse surface.

15 SERVICE

To change direction of handle rotation, proceed as follows:

 

Turn valve to OFF position. Unthread HANDLE

UNTHREAD

 

 

 

 

 

BASE (1) from DECK ADAPTER(2).

1

 

Pull HANDLE ASSEMBLY off VALVE STEM (3).

 

 

 

Remove SPRING CLIP (4). Lift STOP WASHER(5),

 

 

 

turn 90˚ and replace. Replace SPRING CLIP (4).

 

 

Find correct position of HANDLE ASSEMBLY by adjusting

 

 

male teeth on VALVE STEM (3) to female teeth in HANDLE.

Thread HANDLE ASSEMBLY onto DECK ADAPTER (2)

until snug against mounting surface.

4

 

If spout drips, operate handles several times from

2

OFF to ON position. Do not force - handles turn

 

only 90˚.

HANDLE

ASSEMBLY

90˚

3

 

5

M 9 6 8 8 9 3

4

SpeedConnect™ Drain

Troubleshooting Guide

If sink does not hold water even though Stopper is in the “down” position:

• Follow CABLE ADJUSTMENT PROCEDURE.

If Stopper does not raise up fully or sink drains too slowly:

• Follow CABLE ADJUSTMENT PROCEDURE.

If you need to remove the Stopper:

• Follow STOPPER REMOVAL PROCEDURE.

If you would like the ability to remove your Stopper simply by lifting it out of the drain:

Follow STOPPER INSTALLATION PROCEDURE for“Unlocked” mode.

CABLE ADJUSTMENT PROCEDURE

Disconnect the Cable from the Drain by threading the Cable Connector (1) counter-clockwise.Fig. A.

Look at the area on the Drain Body where the Cable was attached and locate the component labeled as “Cam” in the illustration. Fig. B.

Use a small screwdriver to rotate the Cam in the clockwise direction as far as it will go. At this point the Stopper should be in the UP position. Fig. B, C.

Push DOWN on the Lift-Knobto make sure it is fully down.Fig. C.

Re-attachthe Cable to the Drain Body Connection(2) by threading the Cable Connector(1) clockwise onto the Drain Body Connection(2) andhand-tighten.Fig. A.

Fig. A.

 

Fig. B.

Fig. C.

DOWN

 

 

 

 

 

1

CAM

 

 

 

 

 

1

 

 

 

 

 

RE-ATTACH

 

 

 

 

 

CAM CAP

 

 

 

DISCONNECT

 

 

 

 

2

 

 

 

STOPPER REMOVAL PROCEDURE

Disconnect the Cable from the Drain by threading the Cable Connector (1) counter-clockwise.Fig. A.

Look at the area on the Drain Body where the Cable was attached and locate the component labeled as “Cam” and “Cam Cap” in the illustration. Fig. B.

Use fingers or small screwdriver under either side of the Cam Cap to pry it out from the Drain. Fig. D.

Remove the Cam by pulling it straight out while wiggling gently to loosen the Rubber Seal. Fig. E.

The Stopper can now be removed by lifting it out of the Drain. Fig. F.

Fig. D.

Fig. E.

REMOVE

Fig. F.

 

 

CAM

 

 

REMOVE

 

 

 

CAM CAP

 

 

 

 

 

M 9 6 8 8 9 3

 

 

5

 

STOPPER INSTALLATION PROCEDURE

The Stopper can be installed two ways, “Locked” Mode (Stopper cannot be removed) or “Unlock” Mode (Stopper is removable).

Locked Mode:

Look at the Plastic Loop at the bottom of the Stopper and notice that the Loop is on one side of the Stopper. Fig. G.

To install the stopper in “Locked” mode, insert the Stopper into the Drain so that the Plastic Loop is facing toward the rear of the Sink and the American Standard logo is facing front. Rotate

Stopper slightly if necessary so that the Stopper slides all the way down.Fig. G.

Re-installthe Cam into the Drain, rotating the Cam if necessary to make sure it is fully inserted.Fig. J.

Re-installthe Cam Cap, making sure the guide teeth are facing outward. If the Cam Cap does not “snap” into place, then rotate the Cam to make sure it is fully inserted.Fig. K.

Re-attachCable. See “CABLE ADJUSTMENT PROCEDURE” in Troubling Shooting Guide to complete installation. Stopper will be in“Locked” mode and not be removable.

Fig. G.

LOGO

LOOP TOWARD

REAR OF BIDET

DRAIN

Locked Mode

(Vandal Proof)

Unlocked Mode:

Look at the Plastic Loop at the bottom of the Stopper and notice that the Loop is on one side of the Stopper. Fig. H.

To install the stopper in “Unlocked” mode, insert the Stopper into the Drain so that the Plastic Loop is facing toward the front of the

Sink and the American Standard logo is facing rear. Rotate Stopper slightly if necessary so that the Stopper slides all the way down.

Fig. H.

Re-installthe Cam into the Drain, rotating the Cam if necessary to make sure it is fully inserted.Fig. J.

Re-installthe Cam Cap, making sure the guide teeth are facing outward. If the Cam Cap does not “snap” into place, then rotate the Cam to make sure it is fully inserted.Fig. K.

Re-attachCable. See “CABLE ADJUSTMENT PROCEDURE” in “Troublingshooting Guide” to complete installation. Stopper will be in“Unlocked” mode and removable.

Fig. H.

LOGO

180˚

LOOP TOWARD

FRONT OF BIDET

DRAIN

Unlocked Mode

Fig. J.

CAM

Fig. K.

INSTALL CAM

 

INSTALL

 

 

CAM CAP

M 9 6 8 8 9 3

6

 

Installation

 

Instructions

TROPIC

7038.401

Bidet Faucet and Vacuum Breaker with EverClean™ Finish & SpeedConnect™ Drain

Congratulations on purchasing your American Standard faucet with EverClean finish and Speed Connect drain, two features found only on American Standard faucets.

EverClean Finish

Certified to comply with ANSI A112.18.1

• One wipe effortlessly removes spots

SpeedConnect Drain*

M 9 6 8 8 9 4

• Eliminates the need for cleaners and scrubbing

 

• Permanent surface protectant remains beautiful

• Fewer parts, installs in less time

• Never needs adjustment

for the life of the faucet

• Guaranteed to seal properly the first time, every time.

• EverClean™ available on: Polished Chrome, Satin Nickel,

 

Stainless Steel, Polished Brass (or any combination of these finishes)

*Your new American Standard faucet is designed to work only with the SpeedConnect drain.

To ensure that your installation proceeds smoothly-pleaseread these instructions carefully before you begin.

Roughing-inDimensions

 

 

 

8 TO 12

TRANSFER VALVE (FOR FLUSHING

 

 

 

 

 

RIM OR SPRAY)

 

 

 

 

BIDET OUTLINE

 

 

 

(C)

(H)

IS SYMBOLIC

7/8 DIA.

 

 

 

 

 

 

1-3/16DIA.

 

 

DOUCHE SPRAY

ADJ. 1-1/4

2-1/8

 

1-1/4MAX.

 

 

 

TO 2-1/4

DIA.

 

 

 

 

 

 

 

 

3-7/8

1-3/8

 

 

 

 

 

DIA.

 

 

 

 

 

 

 

 

 

 

 

 

5-1/2

 

FINISHED

FINISHED

 

 

 

 

 

 

 

 

 

 

FLOOR

 

 

 

 

 

WALL

 

 

 

 

 

 

 

 

 

 

1-1/4O.D. TAILPIECE

 

 

DIVERTER AND

VACUUM BREAKER

ASSEMBLY

2-1/4DIA.

4-1/4

FOR GROUND JOINT CONNECTION OR 1/2 " O.D. SLIP (INLETS)

REAR VIEW WITH

WALL REMOVED

Required tools

Screwdriver

Plumbers' Putty or

 

Caulking

Phillips Screwdriver

 

 

Channel Locks

Adjustable Wrench

Tubing Cutter

1

 

 

Turn off hot and cold water

BIDET FAUCET INSTALLATION

CAUTION

supplies before beginning.

 

 

Place RUBBER RING (10) into DECK ADAPTER(4).

Install LOCKNUT (1) and RUBBER WASHER(2) onto VALVE BODIES(3, 3a). From under side of mounting surface, install VALVE BODY(3, 3a) through valve mounting holes. Threads of VALVE BODY(3, 3a) should extent at least 5/16 of a inch above4 mounting surface top.Fig. A. Thread DECK ADAPTER(4) onto VALVE BODIES(3, 3a)10 until snug against internal stop. If necessary, adjust LOCKNUT(1).

 

Tighten LOCKNUTS (1) with WRENCH(5) (supplied)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

to secure VALVE BODIES (3, 3a).

 

Fig. A.

 

 

 

 

 

 

 

 

Remove MOUNTING NUT (6), WASHER(7) and

 

 

 

 

 

 

 

 

 

 

 

 

5/16''

 

 

 

 

 

UPPER GASKET (8) from TRANSFER VALVE(9).

 

 

 

MIN.

 

 

 

 

 

Insert TRANSFER VALVE (9) into the center forward

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

hole of BIDET.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Replace UPPER GASKET (8) and WASHER(7) . Position the side threaded outlet rearward and secure MOUNTING

NUT (6). Thread ESCUTCHEON(11) onto TRANSFER3, 3a VALVE(9) until it seats against the BIDET LEDGE.

4

10

MOUNTING

SURFACE

 

2

2

1

1

 

5

11

6

7

BIDET

LEDGE

 

3

3a

 

 

HOT

 

COLD

8

9

2 SPRAY INSTALLATION

Assemble SPRAY BODY (1) to BIDET. Using putty, seal underside of SPRAY BODY FLANGE(2) and secure with NUT(3).

Thread SPRAY HOSE (4) with SEAL WASHER(5) to SPRAY BODY(1). Connect other end of HOSE(4) with SEAL WASHER(6) to side outlet NIPPLE(7) of the TRANSFER VALVE(8).

Thread SPRAY CAP (9) onto SPRAY BODY(1).

8

2

9

7

PUTTY

1

6

3

4

5

 

 

4

1

3 POP-UPDRAIN

Remove CLEAR PLASTIC COVER (1).

Remove CARDBOARD SPACER (2) from under DRAINPOP-UP(3).

Tighten TAILPIECE (4) on DRAIN BODY before installing DRAIN BODY.Fig. B.

Fig. A.

Fig. B.

1

 

3

DRAIN

 

BODY

2

4

 

4 REMOVE FLANGE

Thread FLANGE (1) counter-clockwiseand remove FLANGE(1) and FOAM GASKET(2) from drain body.Fig. A.

Thread LOCKNUT (3) clock-wiseto bottom of drain body. Push GASKET(4) down against LOCKNUT(3). Fig. B.

Fig. A.

Fig. B.

1

4

2

3

5

INSTALL DRAIN FROM

6

BELOW FIXTURE

 

From under side of BIDET

 

 

install DRAIN BODY (1) up

4

 

through drain outlet.

 

 

Note: No plumber’s putty

3

 

or caulk is required.

 

 

The CABLE ATTACHMENT

DRAIN

 

POINT (2) must face towards

OUTLET

 

the rear of the BIDET.

1

 

 

 

Install FOAM GASKET (3) and

2

 

FLANGE (4) onto drain body

 

 

 

from above BIDET and tighten

 

 

FLANGE (4) firmly.

 

TIGHTEN LOCKNUT

Tighten LOCKNUT (1) firmly with Adjustable Wrench or Channel Locks.

1

7 FLANGE GASKET

Fig. A.

Fig. B.

1

Check DRAIN FLANGE in BIDET to ensure that WHITE

 

 

3

FOAM GASKET (1) is fully compressed and not visible.

 

 

 

Fig. A.

DRAIN

 

 

POP-UPROD ASSEMBLY

FLANGE

 

 

 

 

SLOTTED

Insert LIFT ROD GUIDE (1) and CABLE CONNECTOR(2)

 

 

MOUNTING

 

 

NUT

through rear hole, making sure SEAL WASHER (3) is

 

 

4

properly seated. Fig. B.

1 WHITE FOAM

ILLUSTRATION

 

GASKET

2

From below slip slot in MOUNTING NUT (4) over CABLE(5).

NOT VISIBLE

SHOWN LESS

 

VALVES

 

Thread NUT (4) onto lift rod guide shank to secure ROD

 

 

 

GUIDE (1) to bidet. Hand tighten only.Fig. B.

 

 

M 9 6 8 8 9 4

 

2

 

 

8

ATTACH CABLE

Fig. A.

CONNECTOR

 

POP-UPKNOB(1) must be fully

DOWN

 

down. Fig. A.

 

 

Thread CABLE CONNECTOR (1)

 

 

clockwise onto DRAIN BODY

 

 

CONNECTION (2) and hand

 

 

tighten. Fig. B.

 

 

Your new POP-UPDRAIN

 

 

installation is now complete.

 

 

Fig. C.

 

 

Note: Tailpeice onpop-updrain

 

 

is 1-1/4”O.D.Fig. C.

 

Fig. B.

1

2

Fig. C.

1-1/4”O.D.

9 CHECK OPERATION OFPOP-UP

5

Operate LIFT KNOB (1) to verify that STOPPER(2)

4

opens and closes.

3

 

Note: If STOPPER(2) does not open and close properly

1

then refer to the “troubleshooting section” of these

 

instructions.

 

INSTALL DIVERTER KNOB

2

 

Push DIVERTER KNOB (1) onto HANDLE ADAPTER(2).

2

Push on RING (3) and tighten with SCREW(4).

 

Press on KNOB CAP (5).

 

Note: Screwdriver gap is for disassembling and should

 

point downwards.

 

10 TEE AND HOSE CONNECTION

Insert SEAL (1) into ADAPTER(2) and tighten ADAPTER(2) to bottom of TRANSFER VALVE(3).

Install SEAL (4) into coupling nut of TEE(5) and tighten connection to ADAPTER(2).

Connect HOSE COUPLING NUTS (6) to Hot and Cold valve

 

 

3

7a

bodies and securely tighten.

 

1

 

26

 

 

4

 

 

 

Front

 

 

 

 

WATER SUPPLY CONNECTION

 

5

 

COUPLING

7

6

 

NOTE: FLEXIBLE SUPPLIES OR BULL-NOSERISERS NOT

 

NUT

 

 

 

3

INCLUDED AND MUST BE PURCHASED SEPARATELY.

 

 

 

Connect water supply to VALVE BODIES (7,7a) with

1/2" PIPE

 

 

3/8 O.D.

 

 

BULL-NOSE

1/2" IPS FLEXIBLE SUPPLIES (2) or 3/8" O.D.BULL-NOSE

THREAD

 

 

RISERS

 

 

 

 

 

 

 

RISERS (3). Use adjustable wrench to tighten connections.

 

 

 

COMPRESSION

Do not over tighten. Be careful not to kink copper supply when

2

 

 

NUT

bending. Use tubing cutter to cut to proper length.

FLEXIBLE

 

 

 

 

SUPPLIES

 

 

FERRULE

 

 

 

 

Connect HOT water supply to inlet of left SHANK and COLD water supply to right SHANK using sealant, appropriate

connectors, and COUPLING NUTS.

COLD

Connect 1-1/4”O.D. tailpiece onPOP-UPDRAIN to waste outlet.

 

CONNECT TO

HOT

WASTE OUTLET

 

3/8 COMPRESSION CONNECTION

M 9 6 8 8 9 4

3

11 INSTALL HANDLES

Push ADAPTER (1) on VALVE STEM(2), so that the hole of the ADAPTER(1) without a spline is facing up.Fig. A. Tighten STEM SCREW(3) to secure ADAPTER(1).

Find correct position of LEVER HANDLE ASSEMBLY (4) by adjusting male teeth on ADAPTER(1) to female teeth in HANDLE(4).

Thread LEVER HANDLE ASSEMBLY (4) onto DECK ADAPTER(5) until snug against mounting surface.

Fig. A.

SPLINE END DOWN

THREAD ON 4 TO DECK

ADAPTER

TOP

1

3

2

5

12 TEST INSTALLED FITTING

5

1

With HANDLES (1) in OFF position, turn on WATER

SUPPLIES (2) and check all connections for leaks.

Operate both HANDLES (1) to flush water

 

lines thoroughly.

1

3

Rotate TRANSFER VALVE (5) from rim wash to spray several times to check operation.

13 CHECK DRAIN CONNECTIONS

Pull up POP-UPKNOB(3) and fill Bidet with water. Check that DRAIN STOPPER(4) makes a good seal and retains water in Bidet. If STOPPER(4) does not seal properly, please refer to “Troubleshooting Guide” in these instructions.

Push POP-UPKNOB(3) down and check all drain connections and "P" trap for leaks. Tighten

if necessary.

2

4

SPRAY

2

14 EverClean™ Finish

Care Instructions

American Standard’s EverClean finish will wipe clean with a soft, dry cloth.

A soft cloth with clean water may also be used, if desired. No additional cleaning products are required.

DO NOT USE: Soaps, acid, polish, abrasives, harsh cleaners, or a cloth with a coarse surface.

15 SERVICE

To change direction of handle rotation, proceed as follows:

 

Turn valve to OFF position. Unthread HANDLE

UNTHREAD

 

 

 

 

 

BASE (1) from DECK ADAPTER(2).

1

 

Pull HANDLE ASSEMBLY off VALVE STEM (3).

 

 

 

Remove SPRING CLIP (4). Lift STOP WASHER(5),

 

 

 

turn 90˚ and replace. Replace SPRING CLIP (4).

 

 

Find correct position of HANDLE ASSEMBLY by adjusting

 

 

male teeth on VALVE STEM (3) to female teeth in HANDLE.

Thread HANDLE ASSEMBLY onto DECK ADAPTER (2)

until snug against mounting surface.

4

 

If spout drips, operate handles several times from

2

OFF to ON position. Do not force - handles turn

 

only 90˚.

HANDLE

ASSEMBLY

90˚

3

 

5

M 9 6 8 8 9 4

4