Wall-Mount Canopy Grill Vent Hood
PRODUCT MODEL NUMBERS
UXG7360V
UXG7480V
Electrical: 120-volt, 60-Hz, AC-only, 15-amp fused electrical circuit is required.
LOCATION REQUIREMENTS
Canopy grill vent hood location should be away from strong draft areas, such as windows, doors and strong heating vents.
Venting methods
This canopy grill vent hood is factory set for venting through the roof or through the wall. A 10" (25.4 cm) round vent system is needed for installation (not included). The hood exhaust opening is 10" (25.4 cm) round.
NOTE: Flexible vent is not recommended. Flexible vent creates back pressure and air turbulence that greatly reduce performance. Vent system can terminate either through the roof or through the wall. To vent through a wall, a 90° elbow is needed.
Rear discharge
A 90° elbow may be installed immediately above the hood.
Roof Venting |
Wall Venting |
|
C |
|
|
B |
B |
C |
|
||
A |
A |
|
D |
|
D |
A. Optional decorative duct cover |
A. Optional decorative duct cover |
B. 10" (25.4 cm) round vent |
B. 10" (25.4 cm) round vent and |
C. Roof cap |
elbow |
D. 10" (25.4 cm) round vent |
C. Wall cap |
transition |
D. 10" (25.4 cm) round vent |
|
transition |
Calculating Vent System Length
To calculate the length of the system you need, add the equivalent feet (meters) for each vent piece used in the system.
Vent Piece |
10" (25.4 cm) Round |
45° elbow |
2.5 ft |
|
(0.8 m) |
90° elbow |
5.0 ft |
|
(1.5 m) |
Maximum equivalent vent length is 35 ft (10.7 m).
PRODUCT DIMENSIONS
Vented installations
12"
(30.
18" (45.7 cm)
4" (10.2 cm)
30" (76.2 cm) |
24" |
||
36" |
(91.4 cm) |
||
(61.0 cm) |
|||
48" |
(121.9 cm) |
||
|
INSTALLATION DIMENSIONS
|
|
*NOTE:The grill vent hood |
|
|
duct cover is designed to add |
|
|
12" (30.5 cm) to meet the |
|
|
ceiling or soffit height. |
A |
X |
Depending on your model, |
order: |
Part Number W10153151 for 30" (76.2 cm) models,
Part Number W10153152 for 36" (91.4 cm) models,
Part Number W10153153 for 48" (121.9 cm).
IMPORTANT:
Minimum distance “X”: 30" (76.2 cm)
Suggested maximum distance “X”: 36" (91.4 cm)
Example vent system
90 elbow |
|
|
|
|
|
|
Wall cap |
||
|
|
6 ft (1.8 m) |
|
|
|||||
|
|
|
|
|
|
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2 ft
(0.6 m)
The following example falls within the maximum recommended vent length of 35 ft (10.7 m).
1 |
- 90° elbow |
= 5.0 ft (1.5 m) |
1 |
- wall cap |
= 0.0 ft (0.0 m) |
8 ft (2.4 m) straight |
= 8.0 ft (2.4 m) |
|
|
|
|
Length of system |
= 13.0 ft (3.9 m) |
Because Whirlpool Corporation policy includes a continuous commitment to improve our products, we reserve the right to change materials and specifications without notice.
Dimensions are for planning purposes only. For complete details, see Installation |
Ref. W10153187 |
Instructions packed with product. Specifications subject to change without notice. |
02-20-09 |