Amana W10252706B, AER5823XA, AER5830VA, AER5523XA, AER3311WA, AER5524XA Installation Guide

867.54 Kb
Loading...

INSTALLATION INSTRUCTIONS

30" (76 CM) FREESTANDING ELECTRIC RANGES

Table of Contents

 

RANGE SAFETY ...................................................................................

2

INSTALLATION REQUIREMENTS ......................................................

3

Tools and Parts ..................................................................................

3

Location Requirements......................................................................

3

Electrical Requirements - U.S.A. Only ...............................................

4

INSTALLATION INSTRUCTIONS ........................................................

6

Unpack Range....................................................................................

6

Install Anti-Tip Bracket.......................................................................

6

Electrical Connection - U.S.A. Only...................................................

7

Verify Anti-Tip Bracket Location ......................................................

12

Level Range......................................................................................

12

Storage Drawer ................................................................................

12

Complete Installation .......................................................................

13

Moving the Range ............................................................................

14

ANTI-TIP BRACKET TEMPLATE .....................................................

15

IMPORTANT:

Save for local electrical inspector's use.

W10252706B

RANGE SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.” These words mean:

DANGER

WARNING

You can be killed or seriously injured if you don't immediately follow instructions.

You can be killed or seriously injured if you don't follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

WARNING

Tip Over Hazard

A child or adult can tip the range and be killed.

Connect anti-tip bracket to rear range foot.

Reconnect the anti-tip bracket, if the range is moved.

Failure to follow these instructions can result in death or serious burns to children and adults.

2

INSTALLATION REQUIREMENTS

Tools and Parts

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.

Tools needed

Tape measure

Flat-blade screwdriver

Level

Hammer

Hand or electric drill

Wrench or pliers

Marker or pencil

Masking tape

Parts supplied

¼" drive ratchet

¼" nut driver

³⁄" and ⁄" nut driver

¹⁄" (3.2 mm) drill bit (for wood floors)

³⁄" (4.8 mm) carbide-tipped masonry drill bit (for concrete/ceramic floors)

Tin snips or large wire cutters (for cutting ground strap if necessary)

Check that all parts are included.

3 - 10-32 hex nuts (attached to terminal block)

3 - Terminal lugs

A

B

C

A.Anti-tip bracket

B.Plastic anchors (2)

C.#10 x 1¹⁄" screws (2)

Anti-tip bracket kit

Anti-tip bracket must be securely mounted to subfloor. Thickness of flooring may require longer screws to anchor bracket to subfloor. Longer screws are available from your local hardware store.

Parts needed

If using a power supply cord kit:

A UL listed power supply cord kit marked for use with ranges. The cord should be rated at 250 volts minimum, 40 amps or 50 amps that is marked for use with nominal 1³⁄" (3.5 cm) diameter connection opening and must end in ring terminals or open-end spade terminals with upturned ends.

A UL listed strain relief.

Check local codes. Check existing electrical supply. See “Electrical Requirements” section.

It is recommended that all electrical connections be made by a licensed, qualified electrical installer.

Location Requirements

IMPORTANT: Observe all governing codes and ordinances.

It is the installer’s responsibility to comply with installation clearances specified on the model/serial rating plate. The model/serial rating plate is located on the left side frame behind the storage drawer panel.

The range should be located for convenient use in the kitchen.

To eliminate the risk of burns or fire by reaching over heated surface units, cabinet storage space located above the surface units should be avoided. If cabinet storage is to be provided, the risk can be reduced by installing a range hood that projects horizontally a minimum of 5" (12.7 cm) beyond the bottom of the cabinets.

Cabinet opening dimensions that are shown must be used. Given dimensions are minimum clearances.

The floor anti-tip bracket must be installed. To install the antitip bracket shipped with the range, see “Install Anti-Tip Bracket” section.

Grounded electrical supply is required. See “Electrical Requirements” section.

IMPORTANT: To avoid damage to your cabinets, check with your builder or cabinet supplier to make sure that the materials used will not discolor, delaminate or sustain other damage. This oven has been designed in accordance with the requirements of UL and CSA International and complies with the maximum allowable wood cabinet temperatures of 194° (90°C).

Mobile Home - Additional Installation Requirements

The installation of this range must conform to the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280 (formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD Part 280). When such standard is not applicable, use the Standard for Manufactured Home Installations, ANSI A225.1/NFPA 501A or local codes.

Mobile home installations require:

When this range is installed in a mobile home, it must be secured to the floor during transit. Any method of securing the range is adequate as long as it conforms to the standards listed above.

Four-wire power supply cord or cable must be used in a mobile home installation. The appliance wiring will need to be revised. See “Electrical Connection” section.

3

Product Dimensions

A

B

C

F

E

D

A.27¹ ⁄" (69.9 cm) max. depth with handle

B.46" (119.1 cm) overall height (max.) with leveling legs screwed all the way in*

C.36" (91.4 cm) cooktop height (max.) with leveling legs screwed all the way in*

D.29" (75.9 cm) width

E.25" (63.5 cm) depth

F.Model/serial rating plate (located on the left side frame behind storage drawer panel)

*Range can be raised approximately 1" (2.5 cm) by adjusting the leveling legs.

Cabinet Dimensions

Cabinet opening dimensions shown are for 25" (64.0 cm) countertop depth, 24" (61.0 cm) base cabinet depth and 36" (91.4 cm) countertop height.

IMPORTANT: If installing a range hood or microwave hood combination above the range, follow the range hood or microwave hood combination installation instructions for dimensional clearances above the cooktop surface.

A freestanding range may be installed next to combustible walls with zero clearance.

4

A

C

 

B

 

 

D

E

F

A.13" (33.0 cm) max. upper cabinet depth

B.30" (76.2 cm) min. opening width

C.For minimum clearance to top of cooktop, see NOTE*.

D.30¹⁄" (76.5 cm) min. opening width

E.Outlet - 8" (20.3 cm) to 22" (55.9 cm) from either cabinet, 5¹⁄" (14.0 cm) max. from floor

F." (2.2 cm) min. required between cutout and cabinet door or hinge.

*NOTE: 24" (61.0 cm) minimum when bottom of wood or metal cabinet is covered by not less than ¹⁄" (0.64 cm) flame retardant millboard covered with not less than No. 28 MSG sheet steel, 0.015" (0.4 mm) stainless steel, 0.024" (0.6 mm) aluminum or 0.020" (0.5 mm) copper.

30" (76.2 cm) minimum clearance between the top of the cooking platform and the bottom of an uncovered wood or metal cabinet.

Electrical Requirements - U.S.A. Only

If codes permit and a separate ground wire is used, it is recommended that a qualified electrical installer determine that the ground path and wire gauge are in accordance with local codes.

Do not use an extension cord.

Be sure that the electrical connection and wire size are adequate and in conformance with the National Electrical Code, ANSI/ NFPA 70-latest edition and all local codes and ordinances.

A copy of the above code standards can be obtained from: National Fire Protection Association

One Batterymarch Park Quincy, MA 02269.

WARNING: Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service technician if you are in doubt as to whether the appliance is properly grounded. Do not modify the power supply cord plug. If it will not fit the outlet, have a proper outlet installed by a qualified electrician.

+ 12 hidden pages