Altec Lansing VS2121 User Manual

VS•2121	User’s guide	Guía del usuario
	Mode d’emploi	Guia do Usuário

The lightning flash with arrowhead, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

Caution: To prevent the risk of electric shock, do not remove cover (or back). No user-serviceable parts inside. Refer servicing to qualified service personnel.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

CAUTION

To prevent electric shock do not use this (polarized) plug with an extension cord, receptacle or other outlet unless the blades can be fully inserted to prevent blade exposure.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

CONNECTING THE POWER CORD (AC WALL SOCKET)

Long slot is neutral (ground) side.

Insert the wide blade into the ground side slot.

IMPORTANT SAFETY INSTRUCTIONS

1.Read Instructions — All the safety and operating instructions should be read before the appliance is operated.

2.Retain Instructions — The operating instructions should be retained for future reference.

3.Heed Warning — All warnings on the appliance and in the operating instructions should be adhered to.

4.Follow Instructions — All operating and use instructions should be followed.

5.Water and Moisture — The appliance should not be used near water — for example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool, etc.

6.Outdoor Use — Warning: To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.

15.Lightning Storms — Unplug the apparatus during lightining storms.

16.Object and Liquid Entry — Care should be taken so that objects do not fall and liquids are not spilled into the enclosure through openings.

17.Accessories — Only use attachment acessories specified by Altec Lansing Technolgies, Inc.

18.Damage Requiring Service — The appliance should be serviced by qualified service personnel when:

•The power-supply cord or the plug has been damaged.

•Objects have fallen, or liquid has been spilled into the appliance.

•The appliance has been exposed to rain.

•The appliance does not appear to operate normally or exhibits a marked change in performance.

•The appliance has been dropped or the enclosure damaged.

19.Servicing — The user should not attempt to service the appliance. Servicing should be referred to qualified service personnel or returned to the dealer or call the Altec Lansing service line for assistance.

ONE-YEAR LIMITED WARRANTY

Altec Lansing Technologies, Inc. warrants to the end user that all of its powered audio, PC audio, portable audio, TV or gaming speaker systems are free from defects in material and workmanship in the course of normal and reasonable use for a term of one year from the date of purchase.

This warranty is the exclusive and only warranty in effect relative to Altec Lansing powered audio, PC audio, portable audio, TV or gaming speaker systems and any other warranties, either expressed or implied, are invalid. Neither Altec Lansing Technologies, Inc. nor any authorized Altec Lansing Technologies, Inc. reseller is responsible for any incidental damages incurred in the use of the speakers. (This limitation of incidental or consequential damage is not applicable where prohibited.)

Altec Lansing Technologies, Inc.’s obligation under this warranty does not apply to any defect, malfunction or failure as a result of misuse, abuse, improper installation, use with faulty or improper equipment or the use of the speaker systems with any equipment for which they were not intended.

The terms of this warranty apply only to powered audio, PC audio, portable audio, TV or gaming speaker systems when such speakers are returned to the respective authorized Altec Lansing Technologies, Inc. reseller where they were purchased.

7.Location — The appliance should be installed in a stable location.

8.Ventilation — The appliance should be situated so that its location or position does not interfere with its proper ventilation. For example, the appliance should not be situated on a bed, sofa, rug, or similar surface that may block the ventilation openings; or placed in a built-in installation, such as a closed bookcase or cabinet that may impede the flow of air through the ventilation openings.

9.Heat — The appliance should be situated away from heat sources such as radiators, heat registers, stoves, or other appliances (including amplifiers) that produce heat.

10.Power Sources — The appliance should be connected to a power supply only of the type described in the operating instructions or as marked on the appliance.

11.Power-Cord Protection — Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them. Pay particular attention to cords at plugs, convenience receptacles, and the point where they exit from the appliance.

12.Grounding or Polarization — The precautions that should be taken so that the grounding or polarization means of an appliance is not defeated.

13.Cleaning — The appliance should be cleaned only with a polishing cloth or a soft dry cloth. Never clean with furniture wax, benzene, insecticides or other volatile liquids since they may corrode the cabinet.

14.Non-Use Periods — The power cord of the appliance should be unplugged from the outlet when left unused for a long period of time.

CUSTOMER SERVICE

The answers to most setup and performance questions can be found in the Troubleshooting guide. You can also consult the FAQs in the customer support section of our Web site at www.alteclansing.com. If you still can’t find the information you need, please call our customer service team for assistance before returning the speakers to your retailer under their return policy.

1-800-ALTEC-88 (1-800-258-3288)

Email: [e-mail]

For the most up-to-date information, be sure to check our Web site at www.alteclansing.com.

INTERNATIONAL DISTRIBUTION

International customers: For information regarding the distribution of Altec Lansing products in your country, please visit www.alteclansing.com and click on “International.”

1

VS2121	THREE-PIECE POWERED
	AUDIO SYSTEM

Thank you for purchasing this Altec Lansing product. For generations, Altec Lansing has been first in audio innovation. Today, our line of powered speakers has received more performance awards than any other brand. In all kinds of desktop environments, in every price range, Altec Lansing offers sound of distinction — giving even the most demanding customers the audio enjoyment they seek. Just listen to this!

BOX CONTENTS

•2 Speakers

•Subwoofer

•User’s Guide

•Quick Connect Card (may be located on internal box flaps)

PLACING SPEAKERS

SUBWOOFER

All stereo-encoded information is heard through the satellite speakers. The subwoofer contains no stereo imaging, and its sound is non-directional. As a result, the subwoofer doesn’t have to be placed in any particular relationship to the satellites. However, placing the subwoofer on the floor close to a wall or room corner provides better bass efficiency and optimum sound.

Warning: The subwoofer is not magnetically shielded. As such, it SHOULD be placed at least 2 feet (0.6m) from TVs, computer monitors, computer hard drives or any other magnetic media (e.g. floppy disks, Zip disks, computer or audio tapes, etc.).

SATELLITE SPEAKERS

Arrange the satellite speakers to suit your listening tastes — from right next to the monitor to as far apart as the speaker cords allow. Use the key hole on the back of each speaker if you choose to mount them on the wall.

For optimum sound, satellite speakers should be placed at or slightly above ear level, and in an arrangement that offers the most satisfying results.

Note: The satellite speakers ARE magnetically shielded and can be placed close to video displays such as TVs and computer monitors without distorting the image.

MAKING CONNECTIONS

Warning: Do not insert the speaker system’s power plug into a wall outlet until all connections are made. Also, turn off audio source (i.e., your PC, MP3 player, Sony PlayStation, etc.) before connecting the outputs to the speaker system’s inputs.

To ensure first-time operation as expected, please carefully follow the connection sequences described below in the order indicated.

SPEAKER SYSTEM

The satellites are connected together. To set-up the speaker system, insert the orange DIN connector (hardwired into the right satellite) into the input marked RIGHT SPEAKER on the rear of the subwoofer.

Notice that the DIN plug has an arrow. For easy insertion of the DIN connector, the arrow on the connector must face up.

INPUTS

Various connection schemes between your audio source and the speaker system are available. Determine if you’ll be setting up the speaker system for PC audio/PC gaming, DVD playback, console gaming or with portable audio devices (such as MP3 or portable CD players), then skip to the appropriate section.

PC AUDIO/PC GAMING/DVD PLAYBACK

All PC sound cards have audio outputs. Typically, the outputs will be marked as “front output” and “rear output.” In some cases, slightly different terminology may be used. The sound card’s documentation should help you determine which outputs to use with your speaker system.

Connect the lime green 3.5mm stereo cable (hardwired into the right satellite) to the lime green input labeled “FRONT” on your sound card.

CONSOLE GAMING

(Requires the Console Gaming Y-Adapter, which is not included but can be purchased on our Web site at www.alteclansing.com)

Most console game systems feature dual-RCA outputs. To connect your speakers, follow the steps below:

1.Make sure the power to your console gaming system is turned off.

2.The Console Gaming Y-Adapter has a lime green 3.5 mm stereo jack on one end and two RCA jacks on the otheræone red and one white.

3.Connect the red and white RCA cable that came with your console gaming system to the matching red and white RCA jacks on the Console Gaming Y-Adapter.

4.Connect the lime green 3.5mm stereo cable (hardwired into the right satellite) to the lime green input on the Console Gaming Y-Adapter.

PORTABLE AUDIO DEVICES (MP3, PORTABLE CD PLAYERS, ETC.)

Connect the lime green 3.5mm stereo cable (hardwired into the right satellite) to the headphone jack on your portable audio device.

POWERING ON

1.After all other connections are made, plug the AC power cord (on the back of subwoofer) into a wall outlet. The speaker system is now ready to operate.

2.Turn on the audio source.

3.Turn on the speaker system by turning the VOLUME knob on the right satellite until you hear a click sound. An LED will light on the front of the right satellite when the power is ON.

Note: To avoid hearing a popping sound when you turn on your Altec Lansing speaker system, always turn on your audio source first.

VOLUME

The VOLUME knob on the right satellite controls the master volume. Turn the knob clockwise to increase the volume and counterclockwise to decrease the volume.

SFX TECHNOLOGY™

Sound Field Xpander™ technology allows your speaker system to deliver a wider stereo image for bigger sound at the touch of a button. Press the SFX button on the right satellite to turn it on. Press it again to turn it off.

Note: This feature does not work when using headphones.

HEADPHONES

To use headphones with the system, plug them into the labeled jack

on the right satellite. When headphones are connected, the speaker system is muted.

2

SYSTEM SPECIFICATIONS*

Altec Lansing’s superior sound comes from our patented Dynamic EQ technology, which utilizes custom-built, high-fidelity drivers, state-of-the-art equalization circuitry, and a harmonious mix of the following specifications:

	Sound Pressure Level (SPL):	97 dB		POWER REQUIREMENTS
	Total Continuous Power:	28 Watts RMS		USA, Canada and applicable
				Latin American countries:	120 V AC @ 60 Hz
	• Front Speakers:	6 Watts/channel @ 4 ohms
		@ 10% THD @ 180 – 18000 Hz
		2 Channels Loaded		Europe, United Kingdom,
	• Subwoofer:	16 Watts @ 8 ohms @ 10% THD		applicable Asian countries,
		@ 50 – 180 Hz		Argentina, Chile and Uruguay:	230 V AC @ 50 Hz
		Single Channel Loaded
				ETL/cETL/CE/NOM Approved
	System Response:	40 Hz – 20 kHz (-10 dB)
	Signal to Noise Ratio
	@ 1 kHz input:	> 75 dB
	Drivers (per satellite):	One 2" full-range driver
	Subwoofer:	One 4" woofer

*Power rating conforms to FTC Amplifier Rule #16 C.F.R. Part 432.

TROUBLESHOOTING

SYMPTOM	POSSIBLE PROBLEM	SOLUTION
No LEDs are lit.	Power isn’t turned on.	Turn the VOLUME knob on the right speaker until you hear a click sound.
		An LED will light next to the knob when the power is ON.
	AC power cord isn’t connected to the wall outlet.	Check to see if the “Power On” LED is illuminated on the right satellite. If not,
		connect AC power.
	Surge protector (if used) isn’t powered on.	If the AC power cord is plugged into a surge protector, make sure the surge
		protector is switched on.
	Wall outlet not functioning.	Plug another device into the wall outlet (same jack) to verify the wall outlet
		is working.
No sound from	Power isn’t turned on.	Verify the AC power cord is plugged into the wall outlet.
one or more
		Turn the VOLUME knob on the right speaker until you hear a click sound.
speakers.
		An LED will light next to the knob when the power is ON.
	Volume is set too low.	Turn the VOLUME knob clockwise to raise the volume.
		Check volume level on the computer sound card or alternate audio source
		device, and set at mid-level.
	3.5mm stereo cable isn’t connected to audio source.	Check plug connections on the audio source. Make sure the signal cables are
		inserted firmly into the correct jacks.
	3.5mm stereo cable is connected to wrong output on	Make sure the 3.5mm stereo cable is connected and fully inserted into the
	audio source.	“line-out,” “audio-out,” or the headphone jack of the audio source.
	Problem with audio source device.	Test the speakers on another audio device. Remove the 3.5mm stereo cable
		from the audio source device and connect it to “line-out,” “audio-out,” or the
		headphone jack of another audio source.
Crackling sound	Bad connection.	Check all cables. Make sure they are connected to “line-out” or “audio-out”
from speakers.		jack on your sound card or other audio source — NOT “speaker-out.”
	Volume level in computer operating system is set	Check the computer operating system volume level and decrease it if necessary.
	too high.
	A problem with your audio source device.	Unplug the stereo cable from the audio source. Then plug it into the
		headphone jack of an alternate audio source (e.g., Walkman, Discman or
		FM radio).

3

	SYMPTOM	POSSIBLE PROBLEM	SOLUTION
	Sound is	Volume level set too high.	Turn the VOLUME knob counterclockwise to lower the volume.
	distorted.
		Computer operating system volume level is set too high.	Adjust the computer operating system volume and balance levels to the
			center as a starting point, then adjust the level on the speaker using the
			volume control.
		Sound source is distorted.	WAV files are often of poor quality. So distortion and noise are easily noticed
			with high-powered speakers. Try a different sound source such as a music CD.
	Radio	Too close to a radio tower.	Move your speakers until the interference goes away.
	interference.
	No sound from	Bad connection.	Check to make sure that all cables are connected properly and are making a
	subwoofer.		clear connection.
		Sound source has little low-frequency content.	Many .WAV and .MID files often have little low-frequency content and sound
			flat when you listen to them on a computer. Try a song with more bass —
			something from your CD collection.
	Low hum from	The AC in your house is at 60 cycles per second, which is	Some low hum may be detected when your speaker system is powered on
	subwoofer.	within the audio frequency of the subwoofer.	without an audio source playing, or when the volume is set at an extremely
			low level.
	Loud hum from	Bad connection.	Unplug the AC power cord from the surge protector (if used), and plug directly
	subwoofer.		into an AC wall outlet.
			Move your cables. Check to ensure they are making a clear connection.
		Volume on your audio source device is set too high.	Disconnect your 3.5mm stereo cable from the audio source. If the loud hum
			goes away, lower the volume on the audio source.
			Lower the volume or bass level on your computer, portable device, etc.
	Distorted monitor.	Subwoofer too close to monitor.	Because the subwoofer is not magnetically shielded, it can cause distortion if
			it’s too close to your monitor. Move the subwoofer so it’s at least 2 feet from
			your monitor.

4

Le symbole figurant un éclair dans un triangle équilatéral est destiné à attirer l’attention de l’utilisateur sur la présence d’une “tension dangereuse” non isolée pouvant être d’amplitude suffisante pour constituer un risque d’électrocution.

Attention : Pour prévenir tout risque d’électrocution, ne retirez pas le couvercle (ou le dos) de l’appareil. Il ne se trouve à l’intérieur aucune pièce susceptible d’être réparée par l’utilisateur. Confiez la réparation et l’entretien à un personnel qualifié.

Le point d’exclamation à l’intérieur d’un triangle équilatéral est destiné à prévenir l’utilisateur qu’il trouvera d’importantes instructions concernant l’utilisation et la maintenance (entretien) dans la documentation jointe à l’appareil.

ATTENTION

Pour éviter tout risque d’électrocution, n’utilisez pas cette fiche (polarisée) avec une rallonge électrique, une prise de courant ou une autre sortie, si les lames ne peuvent pas être insérées complètement, afin d’éviter qu’elles ne soient exposées.

AVERTISSEMENT

AFIN DE LIMITER LE RISQUE D’INCENDIE OU D’ÉLECTROCUTION, N’EXPOSEZ PAS CET APPAREIL À LA PLUIE OU À L’HUMIDITÉ.

CONNEXION DU CÂBLE D’ALIMENTATION (PRISE MURALE CA)

La fente longue correspond au côté neutre (terre).

Insérez la lame la plus large dans la borne côté terre.

CONSIGNES DE SÉCURITÉ IMPORTANTES

1.Lisez les Instructions — Vous devez lire toutes les consignes de sécurité et le manuel d’utilisation avant de faire fonctionner l’appareil.

2.Conservez les Instructions — Conservez le manuel d’utilisation pour pouvoir vous y référer ultérieurement.

3.Tenez compte des Avertissements — Tous les avertissements figurant sur l’appareil et dans les consignes d’utilisation doivent être respectés.

4.Suivez les Instructions — Le manuel d’utilisation et toutes les consignes d’utilisation doivent être suivis.

5.Eau et Humidité — N’utilisez pas l’appareil près d’une source d’eau — par exemple, près d’une baignoire, d’un lavabo, d’un évier, d’un bac

àlaver, dans un sous-sol humide ou près d’une piscine, etc.

6.Utilisation à l’extérieur — Avertissement : Afin de limiter le risque d’incendie ou d’électrocution, n’exposez pas cet appareil à la pluie ou

àl’humidité.

7.Emplacement — L’appareil doit être installé sur une surface stable.

8.Aération — L’appareil doit être placé de manière à ce que son emplacement ou sa position n’entrave pas son aération correcte. Par exemple, l’appareil ne doit pas être placé sur un lit, un canapé, un tapis ni sur une surface de type similaire, qui pourrait bloquer les orifices d’aération ; ou placé dans une installation encastrée, notamment dans une bibliothèque fermée ou une armoire risquant d’empêcher la circulation de l’air à travers les orifices d’aération.

9.Chaleur — L’appareil doit être tenu éloigné de toute source de chaleur et notamment des radiateurs, des bouches d’air chaud, des réchauds ou des autres appareils (y compris les amplificateurs) produisant de la chaleur.

10.Sources d’Alimentation — Brancher l’appareil uniquement à une source d’alimentation du type mentionné dans le manuel d’utilisation ou indiqué sur l’appareil lui-même.

11.Protection des Câbles d’alimentation — Veillez à ce que les câbles d’alimentation ne se trouvent pas dans un lieu de passage ni bloqués par d’autres objets. Veuillez prêter une attention toute particulière aux câbles au niveau des fiches, des prises de courants et de l’endroit duquel ils sortent de l’appareil.

12.Mise à la terre ou polarisation — Les précautions devant être prises pour que les moyens de mise à la terre ou de polarisation d’un

appareil fonctionnent.

13.Nettoyage — L’appareil ne doit être nettoyé qu’à l’aide d’un chiffon à lustrer ou d’un chiffon doux et sec. Ne le nettoyez jamais avec de la cire pour meubles, du benzène, des insecticides ou d’autres liquides volatiles qui pourraient attaquer le boîtier.

14.Périodes de non-utilisation — Le cordon d’alimentation de l’appareil doit être débranché de la prise lorsque celui-ci n’est pas utilisé pendant une

longue période.

15.Orages — Débranchez l’appareil en cas d’orage.

16.Chutes d’objets et de liquide — Vous devez prendre garde à ne pas faire tomber d’objets ou verser de liquide dans l’enveloppe de protection par les ouvertures.

17.Accessoires — N’utilisez que les équipements/accessoires indiqués par Altec Technologies, Inc.

18.Dommages nécessitant réparation — L’appareil doit être réparé par le personnel qualifié lorsque :

•Le cordon d’alimentation ou la prise ont été endommagés.

•Des objets sont tombés ou du liquide a été renversé dans l’appareil.

•L’appareil a été exposé à la pluie.

•L’appareil ne semble pas fonctionner normalement ou donne des signes de modification notoire de ses performances.

•L’appareil est tombé ou son boîtier a été endommagé.

19.Réparation — L’utilisateur ne doit pas tenter de réparer l’appareil. Les réparations doivent être effectuées par le personnel qualifié, l’appareil doit être retourné au distributeur ou vous devez appeler la ligne téléphonique d’assistance Altec Lansing pour obtenir de l’aide.

GARANTIE LIMITÉE À UN AN

Altec Lansing Technologies, Inc. garantit à l’utilisateur final que tous ses systèmes d’enceintes audio amplifiés, pour ordinateur, systèmes audio portables, pour TV ou consoles de jeux sont exempts de défauts matériels ou de fabrication dans le cadre d’une utilisation normale et raisonnable, et cela pour une durée d’un an à compter de la date d’achat.

Cette garantie est exclusive et tient lieu de seule garantie en vigueur sur les systèmes d’enceintes audio Altec Lansing amplifiés, pour PC, systèmes audio portables, pour TV ou jeux. Aucune autre garantie, explicite ou implicite, n’est valide. Ni Altec Lansing Technologies, Inc. ni aucun revendeur Altec agréé Lansing Technologies, Inc. ne pourra être tenu responsable de dommages accidentels provoqués par l’utilisation des enceintes. (Cette limitation des dommages accidentels ou consécutifs n’est pas applicable là où la loi l’interdit).

Les obligations de Altec Lansing Technologies, Inc. liées à cette garantie ne s’appliquent pas aux défauts, dysfonctionnements ou pannes résultant d’une mauvaise utilisation, d’une utilisation abusive, d’une installation incorrecte, d’une utilisation avec du matériel défectueux ou inapproprié ou d’une utilisation des systèmes d’enceintes avec des équipements pour lesquels ils ne sont pas prévus.

Les conditions de la présente garantie s’appliquent uniquement si les systèmes d’enceintes audio amplifiés, pour ordinateur, systèmes audio portables, pour TV ou jeux sont retournés aux revendeurs Altec Lansing Technologies, Inc. agréés auprès desquels ils ont été achetés.

SERVICE CLIENTÈLE

Vous trouverez les réponses à la plupart des questions concernant l’installation et les performances dans le guide des Conseils de dépannage. Vous pouvez également consulter les FAQ dans la section assistance clientèle de notre site Internet à l’adresse www.alteclansing.com. Si vous ne trouvez toujours pas les informations dont vous avez besoin, veuillez appeler par téléphone notre équipe d’assistance clientèle pour obtenir de l’aide avant de retourner les enceintes à votre détaillant, conformément aux conditions de retour.

1-800-ALTEC-88 (1-800-258-3288)

Email: [e-mail]

Pour obtenir les informations les plus récentes, veuillez consulter notre site Internet à l’adresse suivante www.alteclansing.com.

DISTRIBUTION INTERNATIONALE

Clients internationaux : pour obtenir des informations concernant la vente de produits Altec Lansing dans votre pays, veuillez visiter le site Internet www.alteclansing.com et cliquer sur « International ».

5