9-INCH ADVANCED NAVI STATION
X209D
8-INCH ADVANCED NAVI STATION
X208U
7-INCH ADVANCED NAVI STATION
INE-W977HD
• OWNER’S MANUAL
Please read before using this equipment.
• MODE D’EMPLOI
Veuillez lire avant d’utiliser cet appareil.
• MANUAL DE OPERACIÓN
Léalo antes de utilizar este equipo.
Thank you for purchasing this Alpine product. Please take a moment to protect your purchase by registering your product now at the following address: www.alpine-usa.com/registration.
You will be informed of product and software updates (if applicable), special promotions, news about Alpine.
Merci d’avoir acheté ce produit Alpine. Nous vous invitons à consacrer un moment à la protection de votre achat en enregistrant votre produit dès maintenant à l’adresse suivante : www.alpine-usa.com/registration.
Vous serez tenu informé des mises à jour des produits et des logiciels (le cas échéant), des promotions spéciales et de l’actualité d’Alpine.
Gracias por adquirir este producto Alpine. Con solo unos pocos pasos podrá proteger su producto, registrándolo a través de la siguiente dirección: www.alpine-usa.com/registration.
Recibirá información sobre nuevos productos y software, promociones especiales y novedades sobre Alpine.
EN
FR
ES
ALPINE ELECTRONICS OF AMERICA, INC. |
|
19145 Gramercy Place, Torrance, |
Designed by ALPINE Japan |
California 90501, U.S.A. |
|
Phone 1-800-ALPINE-1 (1-800-257-4631) |
68-34732Z02-A |
Resistant to Dust and Fresh Water (X209D Only)
IP53 rating |
Resistant to Dust and Fresh Water. Rated IP53 under IEC standard 60529. |
|
|
|
|
|
This product has been tested in a controlled, laboratory environment with an IP (Ingress Protection) rating of IP53 |
|
|
under IEC standard 60529, which is an international standard for measuring the level of protection from dust and |
|
|
fresh water. |
|
IP test condition |
The IP rating is a 2-digit code – the first digit indicates the protection level against dust, and the second digit |
|
|
indicates the protection level against fresh water. |
|
|
IP53 means protected against dust with limited ingress, and protected against spraying fresh water up to 60 |
|
|
degrees from vertical. |
|
|
|
|
|
Although this product is rated IP53, it is not impervious to dust or water damage in all situations. |
|
|
• Dust and water resistance is not permanent; resistance may decrease as a result of normal wear or other |
|
|
damage to the product. |
|
Terms of Use and Risk |
• Do not expose to sea/salt water, chlorinated water, mud, detergent or other liquids. |
|
• Do not expose to prolonged rain, fog, humidity, temperature changes or other prolonged weather and |
||
|
||
|
environmental conditions. Condensation, moisture or debris may accumulate in the product. Close vehicle |
|
|
windows, roof and other openings to avoid exposure to the product. |
|
|
• If the product gets wet, dry thoroughly with a soft cloth. |
|
|
• Open/close the product nose with care – dust or water may enter the product. |
|
|
|
|
|
Liquid and dust damage are not covered under warranty. |
|
Disclaimers |
|
|
|
Failure to install the product as directed in the installation manual may degrade dust and water resistance. |
|
|
|
X208U/INE-W977HD
X209D
ENGLISH
Contents |
|
Operating Instructions |
|
PRECAUTIONS |
|
IMPORTANT INFORMATION ........................ |
8 |
WARNING |
|
Points to Observe for Safe Usage ........................ |
8 |
WARNING ...................................................... |
9 |
CAUTION ..................................................... |
10 |
NOTICE ........................................................ |
10 |
Features |
|
Favorite Function ................................................ |
13 |
About Swiping the Touch Screen ...................... |
13 |
Switching the Audio Sources Screen to a |
|
Dedicated Screen ............................................. |
14 |
About Dual Screen .............................................. |
15 |
Dual Screen Display Position ......................... |
15 |
Getting Started |
|
Location of Controls ........................................... |
16 |
Turning Power On or Off .................................. |
17 |
Turning the System On ...................................... |
17 |
Initial System Start-Up ....................................... |
17 |
Adjusting the Volume ......................................... |
17 |
Lowering Volume Quickly ................................. |
17 |
Touch Screen Operation .................................... |
18 |
Switching Sources ................................................ |
18 |
Operating the Function Button on the Audio/ |
|
Video Main Screen .......................................... |
19 |
About Basic Operation for List Screen ............. |
19 |
About the Shortcut Setup Screen ...................... |
20 |
Sound Setup Function ..................................... |
20 |
Rear Seat Entertainment Function ................ |
21 |
About the Menu Screen ...................................... |
22 |
Edit Menu ......................................................... |
22 |
About the Indicator Display .............................. |
23 |
Opening screen Customization ......................... |
23 |
How to Input Characters and Numbers |
|
(Keypad) ........................................................... |
24 |
Favorite Function |
|
Using the Favorite Function .............................. |
25 |
Editing the Favorite Screen ................................ |
25 |
Registering Items ............................................. |
25 |
Changing Item Names .................................... |
26 |
Changing Icons (only the Shortcut Dialing |
|
and Navigation icons) ................................. |
26 |
Changing the Layout ....................................... |
27 |
Deleting Items .................................................. |
27 |
Applying Alpine TuneIt App |
|
Adjusting the sound via the Smartphone ........ |
28 |
Facebook Notification Function ....................... |
28 |
Setup |
|
Setup Operation .................................................. |
30 |
Wireless (Bluetooth) Setup |
|
Bluetooth Setup ................................................... |
31 |
Displaying Bluetooth Information ................ |
31 |
Pairing a Bluetooth Device ............................. |
31 |
Hands-free Device Primary/Secondary |
|
Setting ............................................................ |
32 |
iPhone Auto Pairing Setting .......................... |
32 |
Device Setup ......................................................... |
32 |
Setting the Passcode ........................................ |
32 |
Changing the Character Code of the Phone |
|
Book ............................................................... |
33 |
Selecting the Output Speaker ......................... |
33 |
Setting the Microphone Select (X208U/ |
|
INE-W977HD only) .................................... |
33 |
General Setup |
|
Sound Setup ......................................................... |
34 |
Setting the Balance/Fader/Rear Speaker/ |
|
Subwoofer ..................................................... |
34 |
Setting the Media Xpander (MX HD) .......... |
35 |
Equalizer Presets .............................................. |
35 |
Adjusting the Parametric Equalizer Curve |
|
(Dual HD EQ) .............................................. |
35 |
Adjusting the Crossover Settings |
|
(X-Over) ........................................................ |
36 |
Adjusting the Time Correction (TCR) ......... |
37 |
Setting Defeat ................................................... |
37 |
Setting the Volume for Each Source ............. |
37 |
3-EN
Adjusting the Caller Level .............................. |
37 |
Adjusting the Microphone Level ................... |
37 |
Adjusting the Ring Tone Level ...................... |
38 |
Volume Setting ................................................ |
38 |
Setting Audio Mute On/Off while Backing |
|
up ................................................................... |
38 |
Setting the Microphone Effect ....................... |
38 |
Default Sound Settings ................................... |
38 |
About the Crossover ........................................... |
38 |
About Time Correction ...................................... |
39 |
Picture Quality Setup .......................................... |
40 |
Selecting the Visual EQ Mode |
|
(Factory’s setting) ........................................ |
40 |
Adjusting Brightness ....................................... |
40 |
Adjusting Color of Picture ............................. |
40 |
Adjusting Tint of Picture ............................... |
40 |
Adjusting Image Contrast .............................. |
40 |
Adjusting Picture Quality .............................. |
40 |
Saving and calling the adjusted picture |
|
quality ............................................................ |
40 |
Display/Key Setup ............................................... |
41 |
Screen/Lighting Customize ............................ |
41 |
Switching the Display Color .......................... |
41 |
Switching the Illumination Color (X208U/ |
|
INE-W977HD only) .................................... |
41 |
Setting the Text Scroll ..................................... |
41 |
Switching the Artwork Position .................... |
41 |
General Setup ....................................................... |
42 |
Setting the Menu Language ........................... |
42 |
Format settings ................................................ |
42 |
About X209D/X208U/INE-W977HD .......... |
42 |
Setting Demo mode to Off/On ...................... |
42 |
Vehicle Setup ....................................................... |
42 |
Steering wheel Setting ..................................... |
42 |
Installation Setup ............................................. |
42 |
Source Setup |
|
Radio Setup .......................................................... |
43 |
Setting the TUNER (FM) Tone Quality |
|
(Tuner Condition) ....................................... |
43 |
Setting the TUNER (FM) Frequency Step ... |
43 |
SiriusXM Setup .................................................... |
43 |
Setting the Alert individually for an Artist/ |
|
Song/Favorite Team .................................... |
44 |
Setting ON/OFF of all Songs/Artists/Games |
|
Alert ............................................................... |
44 |
Deleting all stored Alert .................................. |
44 |
Setting the Favorite Sports Team Alerts ...... |
44 |
Setting the Parental Lock ................................ |
44 |
Signal Strength Information .......................... |
45 |
AUX Setup ........................................................... |
45 |
Setting the Auxiliary (AUX) Name ............... |
45 |
Switching the Visual Input Signal System ... |
45 |
HDMI Setup ........................................................ |
46 |
Setting the Bluetooth Pandora® ......................... |
46 |
Apple CarPlay Setup ........................................... |
46 |
System Setup |
|
Camera Setup ....................................................... |
47 |
Setting the Camera Input ............................... |
47 |
Setting the Camera Signal Input ................... |
47 |
Switching Video Source for Multi View |
|
Camera .......................................................... |
47 |
Adjusting the Rear/Front/Side Camera |
|
Guide ............................................................. |
47 |
Camera Interrupt Setting (Power OFF Mode) |
|
(Rear Camera Only) .................................... |
48 |
Setting Multi Camera to On/Off ................... |
49 |
Factory System Setup .......................................... |
49 |
Setting the Source Category ........................... |
49 |
Setting the Default Vehicle Screen ................ |
49 |
Setting the Maestro Module ........................... |
49 |
Rear Seat Entertainment Setup ......................... |
50 |
Remote Sensor Setting .................................... |
50 |
External Accessories Setup ................................ |
50 |
Setting the External Audio Processor ........... |
50 |
Setting the HDMI Selector On/Off ............... |
50 |
Setting the External Accessory Control ....... |
50 |
Smartphone Apps Setup ..................................... |
51 |
Apple CarPlay (Optional) |
|
Access to Apple CarPlay .................................... |
51 |
Android Auto (Optional) |
|
What is Android Auto ........................................ |
52 |
Activate Android Auto ....................................... |
52 |
Alpine Connect App (Optional) |
|
Activate Alpine Connect App ........................... |
52 |
Radio/HD Radio™/RBDS |
|
Radio Basic Operation |
|
Listening to the Radio ........................................ |
54 |
Presetting Stations Manually ............................. |
54 |
Presetting Stations Automatically ..................... |
54 |
Tuning to Preset Stations ................................... |
54 |
Inputting Frequency Directly and Receiving |
|
the Radio Station ............................................. |
55 |
4-EN
Receiving a Multicast (HD Radio™ Mode |
|
only) .................................................................. |
55 |
Selecting the Receivable Program Type (RBDS |
|
FM Radio mode only) ..................................... |
55 |
Forced Analog Mode .......................................... |
55 |
Displaying Radio Text (RBDS FM Radio mode |
|
only) .................................................................. |
55 |
Using Ballgame Mode (HD Radio™ Mode |
|
only) .................................................................. |
56 |
About the Feature Logos .................................... |
56 |
USB Flash drive (Optional) |
|
Playback ................................................................ |
58 |
Fast-forwarding/Fast-reversing (USB Video |
|
only) .................................................................. |
58 |
Stopping Playback (USB Video only) .............. |
58 |
Repeat Play ........................................................... |
58 |
Random Play (USB Audio only) ....................... |
58 |
Searching for a Desired Song ............................. |
58 |
Switching Display Modes (During Video File |
|
Play Back) ......................................................... |
59 |
About USB Video format ................................... |
59 |
iPod/iPhone (Optional) |
|
Playback ................................................................ |
61 |
Searching for a Music File .................................. |
61 |
Quick Search Mode ......................................... |
61 |
Full Search Mode ............................................. |
61 |
Alphabet Search Function ................................. |
62 |
Repeat Play ........................................................... |
62 |
Random Play (Shuffle) ....................................... |
62 |
Pandora® internet radio (optional) |
|
Listening to Pandora® ......................................... |
63 |
“Thumbs” Feedback ........................................... |
64 |
Searching for a Desired Station ......................... |
64 |
Shuffle ................................................................... |
64 |
Creating a New Station ....................................... |
64 |
Bookmarking a Desired Track or Artist .......... |
64 |
Connecting a Bluetooth Device (Bluetooth |
|
Pandora® Only) ................................................ |
65 |
Disconnecting the Bluetooth Connection ... |
65 |
Changing the connecting Bluetooth |
|
Device ............................................................ |
65 |
SiriusXM Satellite Radio Operation |
|
(Optional) |
|
Receiving Channels with the SiriusXM |
|
Tuner ................................................................. |
67 |
Tuning Channels by Category ........................... |
67 |
Changing the Display ......................................... |
67 |
Checking the SiriusXM Radio ID Number ..... |
67 |
Storing Channel Presets ..................................... |
67 |
Tuning Channels using Presets ......................... |
67 |
SmartFavorites Functions .................................. |
68 |
TuneStart™ Function ....................................... |
68 |
TuneScan™ Function ....................................... |
68 |
Search Function ................................................... |
68 |
Selecting the Channel Directly .......................... |
69 |
Storing the desired Song/Artist ......................... |
69 |
Receiving and Tuning to an Alert ..................... |
69 |
Replay Function .................................................. |
70 |
Parental Lock Function ...................................... |
70 |
Using Jump Memory and Jump Recall |
|
function ............................................................. |
70 |
HDMI Device |
|
About HDMI selector (Optional) ................. |
71 |
DVD Player Operation |
|
Inserting/Ejecting a Disc .................................... |
71 |
Inserting the Disc ............................................ |
71 |
Removing the Disc .......................................... |
71 |
DVD Player SETUP ............................................ |
71 |
System Setup .................................................... |
72 |
DVD Contents Setup ...................................... |
72 |
CD Contents Setup ......................................... |
73 |
Audio Setup ...................................................... |
73 |
CD/MP3/WMA/AAC/WAV |
|
Playback ................................................................ |
74 |
Stopping Playback ............................................... |
74 |
Repeat Play ........................................................... |
74 |
MIX (Random Play) ........................................... |
75 |
File/Folder Name Search (Concerning MP3/ |
|
WMA/AAC/WAV) ......................................... |
75 |
Selecting Folders (Concerning MP3/WMA/ |
|
AAC/WAV) ..................................................... |
75 |
Info Mode Function ............................................ |
75 |
5-EN
DVD |
|
Playing a Disc .................................................... |
76 |
If a Menu Screen Appears .............................. |
77 |
Numeric Keypad Input Operations ............. |
77 |
Displaying the Top Menu Screen ................. |
77 |
Displaying the Menu Screen ........................ |
77 |
Playing Still Frames (Pausing) ........................ |
77 |
Stopping Playback ............................................. |
78 |
Fast-forwarding/Fast-reversing ...................... |
78 |
Finding the Beginnings of Chapters/Tracks/ |
|
Files .................................................................. |
78 |
Forward/Reverse frame-by-frame |
|
Playback .......................................................... |
78 |
Repeat Playback ................................................. |
78 |
Searching by Title Number ............................... |
79 |
Searching Directly by Chapter Number ......... |
79 |
Switching the Angle ........................................... |
79 |
Switching the Audio Tracks ............................ |
79 |
Switching the Subtitles (Subtitle Language) |
... 79 |
Info Mode Function ............................................ |
79 |
Switching Display Modes ................................... |
79 |
HDMI Operation |
|
Bluetooth Operation |
|
Setup Before Using .............................................. |
81 |
About Bluetooth .............................................. |
81 |
About the Hands-free Phone ......................... |
81 |
Before Using Bluetooth .................................. |
81 |
Hands-free Phone Control |
|
Answering a Call ................................................. |
82 |
Hanging up the Telephone ................................ |
82 |
Call Waiting Function ........................................ |
82 |
Calling ................................................................... |
83 |
Calling by Favorite Function ......................... |
83 |
Making a phone call using the Phone |
|
Menu ............................................................. |
83 |
Using Voice Recognition function ................... |
84 |
Using Siri .......................................................... |
84 |
Voice Dial Function ........................................ |
84 |
Operations During a Conversation .................. |
85 |
Adjusting the Speech Volume ....................... |
85 |
Changing the Voice Output ........................... |
85 |
DTMF (Touch-Tone) Function .................... |
85 |
Phone Book Function ......................................... |
85 |
Synchronizing the Phone Book ..................... |
85 |
Adding the Phone Book ................................. |
85 |
Deleting the Phone Book Entries .................. |
86 |
Searching in the Phone Book ......................... |
86 |
Bluetooth Audio |
|
Playback ................................................................ |
87 |
Repeat Play ........................................................... |
87 |
Random Play ........................................................ |
87 |
Search Function ................................................... |
87 |
Connecting a Bluetooth Device ........................ |
88 |
Disconnecting the Bluetooth Connection ... |
88 |
Changing the connecting Bluetooth |
|
Device ............................................................ |
88 |
Auxiliary Device (Optional) |
|
Operating Auxiliary Devices (Optional) .......... |
89 |
Operating an AUX, AUX DVD or |
|
GAME ........................................................... |
89 |
Operating an External DVD Player .............. |
89 |
Camera Operation (Optional) |
|
Rear Camera Operation ..................................... |
91 |
Displaying the Rear Camera Image from the |
|
Menu screen ................................................. |
91 |
Displaying the rear view video while the car |
|
is in reverse ................................................... |
91 |
Switching the Image for the Rear Camera ... |
91 |
Guide Display ON/OFF Setting .................... |
91 |
Adjusting the Caution Display Location ...... |
92 |
About the Rear Camera Guide .......................... |
92 |
Front Camera Operation ................................... |
93 |
Displaying the Front Camera image from |
|
the Menu screen. .......................................... |
93 |
Switching the Image Pattern for the Front |
|
Camera .......................................................... |
93 |
About the adjustment of guide display |
|
ON/OFF setting and adjustment of |
|
Caution display location ............................. |
94 |
Side Camera Operation ...................................... |
94 |
Displaying the Side Camera image from the |
|
Menu screen. ................................................ |
94 |
Switching the Image Pattern for the Side |
|
Camera .......................................................... |
94 |
iDataLink Operation |
|
Access to iDataLink Mode ................................. |
95 |
About Parking Sensor screen ......................... |
96 |
External Accessory Control Operation ............ |
97 |
6-EN
About Remote Control Operation |
|
(X209D only) |
|
When Using the Remote Control ..................... |
98 |
Battery Replacement ........................................... |
98 |
Operating the DVD Player ................................ |
99 |
Information |
|
Product Software Update ................................. |
100 |
Cautions about Discs (X209D only) ............... |
100 |
Discs Playable on This Unit (X209D only) ... |
101 |
About the Supported Formats ......................... |
102 |
About MP3/WMA/AAC/FLAC .................. |
102 |
About WAV (Disc) ....................................... |
103 |
About DVDs .................................................. |
104 |
List of Language Codes ..................................... |
105 |
In Case of Difficulty .......................................... |
106 |
If this Message Appears .................................... |
107 |
Specifications ..................................................... |
110 |
END USER LICENSE AGREEMENT |
|
(HERE) ............................................................ |
112 |
LIMITED WARRANTY |
|
7-EN
If there is anything in the manual about the operation of the navigation system which you are uncertain about, please contact your local Alpine authorized navigation dealer or Alpine at 1-888-NAV-HELP (1-888-628-4357) before using the navigation system.
PLEASE READ CAREFULLY BEFORE USING THIS PRODUCT
This product is intended to provide turn by turn instructions to get you to a desired destination. Please make certain that all persons using this navigation system carefully read these precautions and the following instructions fully.
•This product is not a substitute for your personal judgment. Any route suggestions made by this navigation system may never supersede any local traffic regulations or your personal judgment and/or knowledge of safe driving practices. Do not follow route suggestions if the navigation system instructs you to perform an unsafe or illegal maneuver, places you in an unsafe situation, or routes you into an area which you consider unsafe.
•Glance at the screen only when necessary and safe to do so. If prolonged viewing of the screen is necessary, pull over in a safe and legal manner and location.
•Do not input destinations, change settings, or access any functions requiring a prolonged view of the monitor and/or remote control while you are driving. Pull over in a safe and legal manner and location before attempting to access the system.
•Do not use the navigation system to route you to emergency services. Not all locations of emergency services such as police and fire stations, hospitals and clinics are contained in the database. Please use your own judgment and ask for directions in these situations.
•The map database used in the navigation system is the most recent map data available at the time of production. Because of changes in streets and neighborhoods, there may be situations where the navigation system is not able to route you to your desired destination. In these cases, use your own judgment.
•The map database is designed to provide you with route suggestions and does not take into account the relative safety of a suggested route or of factors which may affect the time required to reach your destination. The system does not reflect road closures or construction, road characteristics (i.e. type of road surface, slope or grade, weight or height restrictions, etc.), traffic congestion, weather conditions, or any other factors which may affect the safety or timing of your driving experience. Use your own personal judgment if the navigation system is unable to provide you with an alternate route.
•There may be situations where the navigation system displays the vehicle’s location erroneously. Use your own driving judgment in this situation, taking into account current driving conditions.
Please be aware that in this situation the navigation system should correct the vehicle’s position automatically. However, there may be times where you may have to correct the position yourself. If this is the case, pull over in a safe and legal manner and location before attempting operation.
•Make certain that the volume level of the navigation system is set to a level which still allows you to hear outside traffic and emergency vehicles.
FCC COMPLIANCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide more reasonable protection against harmful interference in a residential installation, and are more stringent than “outdoor” requirements.
Operation is subjected to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, you are encouraged to try to correct the interference by one of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and the receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•Consult an experienced radio/TV technician.
•Read this manual carefully before using this disc and the system components. They contain instructions on how to use this product in a safe and effective manner. Alpine cannot be responsible for problems resulting from failure to observe the instructions in this manual.
•This manual uses various pictorial displays to show you how to use this product safely and to alert you to potential dangers resulting from improper connections and operation. Following are the meanings of these pictorial displays. It is important to fully understand the meanings of these pictorial displays in order to use this manual and the system properly.
•This product may be used with software applications. Please follow all usage instructions and warnings when using this product at all times. Do not use this product or any software application in a manner which will hinder safe operation of your vehicle.
•This product may be used in conjunction with the Alpine KAC-001 External Accessory Control module, which works with various accessory products manufactured by third parties. Please review and follow all manufacturer's instructions and warnings for all accessory products.
8-EN
•Operation of the system while driving is dangerous. Users should stop vehicle before operating the software.
•Road conditions and regulations take precedence over information contained on the map display: observe actual traffic restrictions and circumstances while driving.
•This software is designed for use exclusively in the unit. It cannot and may not be used in conjunction with other hardware.
WARNING
This symbol means important instructions. Failure to heed them can result in serious injury or death.
INSTALL THE PRODUCT CORRECTLY SO THAT THE DRIVER CANNOT WATCH TV/VIDEO UNLESS THE VEHICLE IS STOPPED AND THE EMERGENCY BRAKE IS APPLIED.
It is dangerous for the driver to watch TV/Video while driving a vehicle. Installing this product incorrectly enables the driver to watch TV/Video while driving. This may cause a distraction, preventing the driver from looking ahead, thus causing an accident. The driver or other people could be severely injured.
DO NOT WATCH VIDEO WHILE DRIVING.
Watching the video may distract the driver from looking ahead of the vehicle and cause an accident.
DO NOT OPERATE ANY FUNCTION THAT TAKES YOUR ATTENTION AWAY FROM SAFELY DRIVING YOUR VEHICLE.
Any function that requires your prolonged attention should only be performed after coming to a complete stop. Always stop the vehicle in a safe location before performing these functions. Failure to do so may result in an accident.
DO NOT FOLLOW ROUTE SUGGESTIONS IF THE NAVIGATION SYSTEM INSTRUCTS YOU TO PERFORM AN UNSAFE OR ILLEGAL MANEUVER, OR PLACES YOU IN AN UNSAFE SITUATION OR AREA.
This product is not a substitute for your personal judgement. Any route suggestions by this system should never supersede any local traffic regulations or your personal judgement or knowledge of safe driving practice.
KEEP THE VOLUME AT A LEVEL WHERE YOU CAN STILL HEAR OUTSIDE NOISES WHILE DRIVING.
Excessive volume levels that obscure sounds such as emergency vehicle sirens or road warning signals (train crossings, etc.) can be dangerous and may result in an accident. LISTENING AT LOUD VOLUME LEVELS IN A CAR MAY ALSO CAUSE HEARING DAMAGE.
MINIMIZE DISPLAY VIEWING WHILE DRIVING.
Viewing the display may distract the driver from looking ahead of the vehicle and cause an accident.
DO NOT DISASSEMBLE OR ALTER.
Doing so may result in an accident, fire or electric shock.
USE ONLY IN CARS WITH A 12 VOLT NEGATIVE GROUND.
(Check with your dealer if you are not sure.) Failure to do so may result in fire, etc.
KEEP SMALL OBJECTS SUCH AS SCREWS OUT OF THE REACH OF CHILDREN.
Swallowing them may result in serious injury. If swallowed, consult a physician immediately.
USE THE CORRECT AMPERE RATING WHEN REPLACING FUSES.
Failure to do so may result in fire or electric shock.
DO NOT BLOCK VENTS OR RADIATOR PANELS.
Doing so may cause heat to build up inside and may result in fire.
USE THIS PRODUCT FOR MOBILE 12V APPLICATIONS.
Use for other than its designed application may result in fire, electric shock or other injury.
MAKE THE CORRECT CONNECTIONS.
Failure to make the proper connections may result in fire or product damage.
BEFORE WIRING, DISCONNECT THE CABLE FROM THE NEGATIVE BATTERY TERMINAL.
Failure to do so may result in electric shock or injury due to electrical shorts.
DO NOT ALLOW CABLES TO BECOME ENTANGLED IN SURROUNDING OBJECTS.
Arrange wiring and cables in compliance with the manual to prevent obstructions when driving. Cables or wiring that obstruct or hang up on places such as the steering wheel, gear lever, brake pedals, etc. can be extremely hazardous.
DO NOT SPLICE INTO ELECTRICAL CABLES.
Never cut away cable insulation to supply power to other equipment. Doing so will exceed the current carrying capacity of the wire and result in fire or electric shock.
DO NOT DAMAGE PIPE OR WIRING WHEN DRILLING HOLES.
When drilling holes in the chassis for installation, take precautions so as not to contact, damage or obstruct pipes, fuel lines, tanks or electrical wiring. Failure to take such precautions may result in fire.
DO NOT USE BOLTS OR NUTS IN THE BRAKE OR STEERING SYSTEMS TO MAKE GROUND CONNECTIONS.
Bolts or nuts used for the brake or steering systems (or any other safety-related system), or tanks should NEVER be used for installations or ground connections. Using such parts could disable control of the vehicle and cause fire etc.
DO NOT INSTALL IN LOCATIONS WHICH MIGHT HINDER VEHICLE OPERATION, SUCH AS THE STEERING WHEEL OR GEARSHIFT.
Doing so may obstruct forward vision or hamper movement etc. and results in serious accident.
9-EN
This symbol means important instructions. Failure to heed them can result in injury or material property damage.
HALT USE IMMEDIATELY IF A PROBLEM APPEARS.
Failure to do so may cause personal injury or damage to the product. Return it to your authorized Alpine dealer or the nearest Alpine Service Center for repairing.
HAVE THE WIRING AND INSTALLATION DONE BY EXPERTS.
The wiring and installation of this unit requires special technical skill and experience. To ensure safety, always contact the dealer where you purchased this product to have the work done.
USE SPECIFIED ACCESSORY PARTS AND INSTALL THEM SECURELY.
Be sure to use only the specified accessory parts. Use of other than designated parts may damage this unit internally or may not securely install the unit in place. This may cause parts to become loose resulting in hazards or product failure.
ARRANGE THE WIRING SO IT IS NOT CRIMPED OR PINCHED BY A SHARP METAL EDGE.
Route the cables and wiring away from moving parts (like the seat rails) or sharp or pointed edges. This will prevent crimping and damage to the wiring. If wiring passes through a hole in metal, use a rubber grommet to prevent the wire’s insulation from being cut by the metal edge of the hole.
DO NOT INSTALL IN LOCATIONS WITH HIGH MOISTURE OR DUST.
Avoid installing the unit in locations with high incidence of moisture or dust. Moisture or dust that penetrates into this unit may result in product failure.
Product Cleaning
Use a soft dry cloth for periodic cleaning of the product. For more severe stains, please dampen the cloth with water only. Anything else has the chance of dissolving the paint or damaging the plastic.
Temperature
Be sure the temperature inside the vehicle is between +45°C (+113°F) and 0°C (+32°F) before turning your unit on.
Maintenance
If you have problems, do not attempt to repair the unit yourself. Return it to your Alpine dealer or the nearest Alpine Service Station for servicing.
Protecting the USB connector
•Only an iPod/iPhone or USB flash drive can be connected to the USB connector on this unit. Correct performance using other USB products cannot be guaranteed.
•If the USB connector is used, be sure to use only the supplied connector cable with the unit. A USB hub is not supported.
•Depending on the connected USB flash drive, the unit may not function or some functions may not be performed.
•The audio file format that can be played back on the unit is MP3/WMA/AAC/FLAC.
•Artist/song name, etc., can be displayed. Certain, special characters may not be correctly displayed.
10-EN
CAUTION
Alpine accepts no responsibility for lost data, etc., even if data, etc., is lost while using this product.
On Handling USB Flash drive
•This unit can control a memory storage device that supports the USB Mass Storage Class (MSC) protocol. Playable audio file formats are MP3, WMA, AAC and FLAC.
•USB Flash drive function is not guaranteed. Use USB flash drive according to the terms of agreement. Read the USB flash drive Owner’s Manual thoroughly.
•Avoid usage or storage in the following locations:
Anywhere in the car exposed to direct sunlight or high temperatures.
Anywhere the possibility of high humidity or corrosive substances are present.
•Fix the USB flash drive in a location where driver operation will not be hindered.
•USB Flash drive may not function correctly at high or low temperature.
•Use only certified USB flash drive. Note that even certified USB flash drive, may not function correctly depending on its type or state.
•Depending on the settings of the USB flash drive type, memory state or encoding software, the unit may not play back or display properly.
•USB Flash drive may take time to start playback. If there is a particular file other than audio in the USB flash drive, it may take considerable time before the file is played back or searched.
•The unit can play back “mp3,” “wma” or “m4a” file extensions.
•Do not add the above extensions to a file other than audio data. This non-audio data will not be recognized. The resulting playback may contain noise that can damage speakers and/or amplifiers.
•It is recommended to back up important data on a personal computer.
•Do not remove the USB device while playback is in progress. Change SOURCE to something other than USB, then remove the USB device to prevent possible damage to its memory.
•Windows Media and the Windows logo are trademarks, or registered trademarks of Microsoft Corporation in the United States and/or other countries.
•Apple, iPhone, iPod, and iPod touch are trademarks of Apple Inc., registered in the U.S. and other countries. Apple CarPlay is a trademark of Apple Inc.
•“Made for iPod” and “Made for iPhone” mean that an electronic accessory has been designed to connect specifically to iPod, or iPhone, respectively, and has been certified by the developer to meet Apple performance standards.
•Use of the Apple CarPlay logo means that a vehicle user interface meets Apple performance standards. Apple is not responsible for the operation of this vehicle or its compliance with safety and regulatory standards. Please note that the use of this product with iPhone, or iPod may affect wireless performance.
•Pandora, the Pandora logo, and the Pandora trade dress are trademarks or registered trademarks of Pandora Media, Inc., used with permission. Pandora is currently available in the U.S., Australia and New Zealand.
•HD Radio Technology manufactured under license from iBiquity Digital Corporation. U.S. and Foreign Patents. For patents see http://patents.dts.com/. HD Radio and the HD, HD Radio, and “ARC” logos are registered trademarks or trademarks of iBiquity Digital Corporation in the United States and/or other countries.
•Sirius, XM and all related marks and logos are trademarks of Sirius XM Radio Inc. All rights reserved.
•Google, Android, Android Auto, Google Play and other marks are trademarks of Google Inc.
•The Bluetooth® word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and any use of such marks by Alpine Electronics, Inc. is under license.
•The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing, LLC in the United States and other countries.
•MPEG Layer-3 audio coding technology licensed from Fraunhofer IIS and Thomson. Supply of this product only conveys a license for private,non-commercial use and does not convey a license nor imply any right to use this product in any commercial (i.e. revenue-generation) real time broadcasting (terrestrial, satellite, cable and/or any other media), broadcasting/streaming via internet, intranets and/or other networks or in other electronic content distribution systems, such as pay-audio or audio-on-demand applications. An independent license for such use is required. For details, please visit http://www.mp3licensing.com
•©1987-2015 HERE. All rights reserved.
11-EN
X209D only
•This item incorporates copy protection technology that is protected by U.S. patents and other intellectual property rights of Rovi Corporation. Reverse engineering and disassembly are prohibited.
•Manufactured under license from Dolby Laboratories. Dolby, Dolby Audio and the double-D symbol are trademarks of Dolby Laboratories.
•For DTS patents, see http://patents.dts.com. Manufactured under license from DTS Licensing Limited. DTS, the Symbol, & DTS and the Symbol together are registered trademarks, and DTS 2.0+Digital Out is a trademark of DTS, Inc. © DTS, Inc. All Rights Reserved.
• is a trademark of DVD Format/Logo Licensing Corporation.
12-EN
The screen design used in the Owner’s Manual may differ from the actual screen.
Frequently used functions can be easily recalled. For details, see “Favorite Function” (page 25).
Favorite screen example
•Frequently used functions and useful functions can be customized for your convenience.
•You can register up to 54 functions.
•You cannot register a function more than once.
You can change a screen or a page by swiping the touch screen vertically or horizontally with your finger. For details, see “Touch Screen Operation” (page 18).
Swipe the display with your finger lightly.
13-EN
You can switch the Audio Sources screen to a dedicated screen by touching the icon on one of the four edges of the screen, or by swiping vertically or horizontally. For details on how to swipe the screen, see “Touch Screen Operation” (page 18).
• The operation is not available when using Apple CarPlay or Android Auto.
Shortcut Setup Screen (page 20) |
Dual Screen (page 15) |
You can set the Sound Setup or Rear Seat Entertainment |
You can switch between the displayed screens on |
System. |
the Dual Screen. |
<Audio Sources Screen>
(USB Audio)
Preset button or Quick Search mode Screen *1 |
Menu Screen *2 (page 22) |
You can make settings on the Menu Screen.
*1 The Search mode differs depending on the audio source. For details, see the operating instructions of the audio source. *2 The screen also switches by pressing the Menu button.
14-EN
Dual Screen allows you to display the Navigation and Audio/Visual screens simultaneously.
Audio full Screen
Touch [ ], or |
Touch [ ], or |
swipe to the right. |
swipe to the left. |
Dual Screen
Touch [ ], or |
Touch [ ], or swipe to |
swipe to the right. |
the left. |
Navigation full Screen
*Touch [ ], or swipe to the left to switch to the Navigation menu screen. For details of navigation operations, refer to “Navigation System OM” in the website at http://www.alpine-usa.com.
You can switch the left/right positions of the Audio/Visual screen and Navigation screen.
Each time you touch , the positions of Audio/Visual screen and Navigation screen switch.
• When is not displayed, touch [ ].
15-EN
For X208U/INE-W977HD |
For X209D
Microphone (X208U/INE-W977HD only)
Used for Hands-free or Voice Control modes.
(AUDIO) button
Displays the Audio/Visual screen. If the Audio/Visual screen is already displayed, changes the source.
or VOICE button
Depending on the connected smartphone, press to recall Siri function or voice recognition mode.
/ or / (UP/DOWN) button
Press to adjust the volume.
(Favorite) button
Recalls the Favorite screen.
•Press and hold this button for at least 2 seconds to switch to the iDataLink mode screen. (When connected to the optional iDataLink module.)
MENU/ (Power Off) button
Recalls the Menu screen.
Press and hold this button for at least 5 seconds to turn the power off.
/ button
Press to seek down/up a station in radio mode or down/up a track, chapter, etc., in other audio/visual sources.
RESET switch
The system of this unit is reset.
(NAV) button
Recalls the navigation map screen.
Press again to switch to Navigation menu screen.
Press and hold this button for at least 2 seconds to change to Go Home route screen. (If Home is not set yet, it will change to the Home setting screen.)
When the Apple CarPlay or Android Auto is used, the operation may differ. Press (NAV) to change the map screen between smartphone and this unit.
For details of navigation operations, refer to “Navigation System OM” in the website at http://www.alpine-usa.com.
Remote Sensor
Point the remote control transmitter towards the remote sensor within a range of 2 meters.
(Eject) button (X209D only)
Ejects a disc.
Controllable with Remote Control
This unit can be controlled with an optional Alpine remote control. For details, consult your Alpine dealer. Point the optional remote control transmitter at the remote control sensor.
About the button descriptions used in this Owner’s Manual
The buttons found on the face of the unit are expressed in bold (e.g. MENU). The buttons found on the touch-screen display are shown in bold within brackets, [ ] (e.g. [ ]).
16-EN
Some of this unit’s functions cannot be performed while the vehicle is in motion. Be sure to stop your vehicle in a safe location and apply the parking brake, before attempting these operations.
1Turn the ignition key to the ACC or ON position.
The system turns on.
•When turned on, the system displays the last screen that was displayed before the ignition key was turned off. For example, if the unit is in radio mode when ignition is turned off, it will remain in radio mode when ignition is turned back on.
2Press and hold the MENU/ (Power Off) button for at least 5 seconds to turn the power off.
•The unit can be turned on by pressing any button.
•The unit is a precision device. Careful handling of the unit should provide you with years of trouble-free operation.
Be sure to press the RESET switch when using the unit for the first time, after changing the car battery, etc.
1Turn off the unit power.
2Press the RESET switch with a ballpoint pen or similar pointed object.
For X208U/INE-W977HD
RESET switch
For X209D
When the system is used for the first time, the language selection menu is displayed. Swipe the Language list screen vertically, then touch your choice from the list of 23 languages.
•Some of this unit’s functions cannot be performed while the vehicle is in motion. Be sure to stop your vehicle in a safe location and apply the parking brake before attempting these operations.
RESET switch
Adjust the volume by pressing/or /.
Volume decreases/increases continuously by pressing and holding / or /.
Volume: 0 - 35
Audio Mute function instantly lowers the volume level to 0.
1 Press/or /to display the Volume adjunstment screen.
2Touch the speaker icon to activate the MUTE mode and the speaker icon change to .
The audio level will be 0.
3Press and hold or button continuously to increase the volume.
17-EN
You can operate the system by using the touch panel on the screen.
•Be sure to touch the onscreen button lightly with the pad of your finger to avoid scratching the display.
Touch operation
Touch a button or list item on the screen lightly.
•If you touch a button and there is no reaction, remove your finger.
•Onscreen buttons that cannot be operated are dimmed.
Swipe operation
Move your finger lightly with a swipe.
Drag & Drop operation
Touch and hold the desired item, then drag it to its new location by moving your finger, then release your finger to place the item.
•It is not possible to narrow the screen with two fingers (pinch in) or spread the screen (pinch out).
Press the (AUDIO) button to change the source.
Switching sources using the (AUDIO) button
During audio/visual playback, press the (AUDIO) button repeatedly to switch to the desired source.
Radio USB/iPod*1 Factory Media (USB/iPod)*2 HDMI/ DVD*1, 3 Pandora*1 Bluetooth Pandora*1, 4 SiriusXM*1 or Factory SiriusXM*2 AUX*3, 5 Bluetooth Audio*1 Apple CarPlay Music/Google Play Music*6 Radio
*1 When no USB flash drive/iPod/HDMI device/Smartphone/Bluetooth compatible device/SiriusXM Tuner is connected, this option is not available. When using Apple CarPlay, some option may not available.
*2 Not displayed when your car does not support the source or “Setting the Source Category” (page 49) is set to “Aftermarket.” This is also not displayed when the iDataLink module is not connected.
*3 The name set for “HDMI Setup” (page 46), “Setting the Auxiliary (AUX) Name” (page 45), is displayed.
*4 When Bluetooth Pandora is set to “Off”, this option is not available. (page 46)
*5 When AUX is set to “Off,” this option is not available. (page 45) When the iDataLink module (sold separately) is connected, the Auxiliary (AUX) mode is not available.
*6 Available when Apple CarPlay is used/Android™ smartphone which installed Android Auto App is connected.
To play Apple CarPlay music shall impact iPod source when an iPhone 5 or later is connected and vice versa. Refer to “Apple CarPlay Setup” (page 46).
Switching Sources from the Menu screen
1Press the MENU button.
The menu screen is displayed.
•You can also display the menu screen by touching the lower part of the Audio source screen or by swiping upward.
The Audio source selecting area
2Touch your desired source in the Audio source selecting area.
•In the menu screen, you can change the Audio source directly or change the order in which sources change. For details, see “About the Menu Screen” (page 22).
18-EN
Operating the Function Button on the Audio/ Video Main Screen
Using the Function button on the Audio/Visual main screen.
Touch [ ] to change to the Function mode.
HD Radio main screen example
Function mode
Swipe to the right or left to change to the Function mode.
To close the Function mode, touch [ ].
•Depending on the Audio source, the Function mode displays from the beginning.
Basic operations on the Setup list screen and the Search list screen. How to display on the list screen differs depending on the selected item.
Switches to the menu screen or the previous screen. Item select button
Closes the window. Displays the next list page.
•When the next selection item does not exist, the list item is not displayed.
Lists items for selection
•When there are more than five list items, the page can be changed by swiping vertically.
Returns to the list screen of the page that you touched.
•The list screens that can be displayed are up to the 2 previous pages. If you touch [], you can recall your desired page.
Changes the page of the Item select button |
above. |
•“ ” indicates the total number of pages, “ ” indicates the location of the current page.
List screen close button
•Touch or swipe to the left on the search screen, etc. to close the list screen.
19-EN
Displaying the Sound Setup screen, or the Shortcut Setup screen of the Rear Seat Entertainment System screen.
Touch the top part of the Audio source screen or swipe downward.
The Sound Setup screen or the Rear Seat Entertainment System Setup Screen is displayed.
Sound Setup screen (Tone Adjustment mode) example
You can adjust the attention tone (Ding) before the voice navigation starts and Navi voice interrupt volume (Navi Guide).
Volume: 0 - 35
Button for Display Off *
Displays the registered Bluetooth Device List screen.
• See “Pairing a Bluetooth Device” (page 31).
Touch this or swipe upward to change to the currently playing source screen.
Displays the Hands-free Device Primary/Secondary setting screen.
•See “Hands-free Device Primary/Secondary Setting” (page 32).
* Display Off mode
-To cancel Display Off mode, touch the screen or press any button.
-Display Off mode is canceled when the power or ACC is turned off.
-When the gear lever is shifted to the reverse (R) position and the rear camera is connected, the rear camera image is displayed.
-When a call is received on a Bluetooth-connected phone, the incoming call screen is displayed.
Tone Adjustment mode
BASS ENGINE SQ mode
Button for changing the BASS ENGINE SQ mode screen Balance/Fader Image area*1
• To reset to the initial settings (Balance: 0, Fader: 0), touch [].
Rear Seat Entertainment Function screen switch button
•When Setting the Rear Seat Entertainment is “Off,” you cannot change the screen. For details on Rear Seat Entertainment setting, see “Rear Seat Entertainment Setup” (page 50).
Buttons for switching between Front/Rear when adjusting Bass/Treble*2
Buttons for adjusting Bass Level/Treble Level*3, 4 Buttons for adjusting Media Xpander *1, 3, 5 Buttons for adjusting Subwoofer Level *1, 3, 6
Button for changing the Tone Adjustment mode screen
•If changing to the Tone Adjustment mode, BASS ENGINE SQ mode will be disabled.
Buttons for adjusting the BASS ENGINE Level*4
Buttons for selecting the BASS ENGINE type *4
*1 You can perform a more detailed set up in “Sound Setup” (page 34). *2 You cannot switch when Front/Rear Sync in “Adjusting the Parametric
Equalizer Curve (Dual HD EQ)” (page 35) is “On.”
*3 When you switch to the BASS ENGINE SQ mode, the value you have set is ignored.
*4 When the Defeat setting is “On,” you cannot perform the set up.
*5 Not available during an interruption such as traffic announcement is broadcasting.
*6 If the Subwoofer setting is “Off,” the setting cannot be changed. See “Turning Subwoofer ON/OFF” (page 34).
20-EN
Adjusting Bass Level/Treble Level
Bass Level and Treble Level can be set independently set for Front and Rear speakers by touching [Front] or [Rear].
Setting item:
Bass / Treble
Setting contents:
-14 to +14 (Initial setting: 0)
•When “BASS ENGINE SQ” is selected in the Shortcut Setup, this setting is disabled.
•Adjustment cannot be performed when Defeat is set to “On.”
•The Bass adjusted setting value is interlinked with Band2 of Dual HD EQ, and the Treble adjusted setting value is interlinked with Band8.
Setting the BASS ENGINE SQ
Setting the BASS ENGINE Type
Creating the ideal Bass impact for your musical taste using BASS ENGINE SQ.
Setting contents:
Standard (Initial setting) / Punch / Rich / Mid Bass / Low Bass
Standard: |
Mild low-end boost with mid-range focus for front- |
|
center staging. |
Punch: |
Mid-bass punched up with mid-range impact. |
Rich: |
Accented highs and mid-bass giving outstanding |
|
balance for all types of music. |
Mid Bass: |
Strong high frequency emphasis with mid-bass boost |
|
for more low-end attack. |
Low Bass: |
Strong, low-bass boost with extended highs for a very |
|
dynamic sound. |
Adjusting the BASS ENGINE Level
You can adjust the BASS ENGINE Level.
Setting item:
BASS ENGINE Level
Setting contents:
0 to 6 (Initial setting: 3)
•The BASS ENGINE Level 0 of the BASS ENGINE SQ is common to all the types.
About setup when the external power amplifier is connected
In order to optimize the BASS ENGINE SQ mode, we recommend the following procedure to set up the power amplifier.
Use your favorite music to make the following amplifier adjustment.
1)Set GAIN of the power amplifier to “MIN.”
2)Set the Crossover Mode Selector switch to “OFF.”
•If the switch has no “OFF” position, set as near as possible to full range.
3)Set the BASS ENGINE Level to “03.”
4)Play a song of the genre you frequently listen to, and adjust GAIN of the power amplifier.
The Rear Seat Entertainment function independently routes different sources to the front and the rear side of the car. For example, while listening to the radio or other audio sources in the front, HDMI can be enjoyed at the rear with optional rear monitors and headphones.
Rear Seat Entertainment System Setup screen
Button for changing to the Sound Setup screen.
Visual source selection area that is displayed on the Rear monitor.*1
Touch the source icon displayed on the Rear monitor.
Front: The image and sound of the same visual source as the unit are output.
Off: Stops output to the Rear monitor.
Illumination Color button
The color coordination select button of the Rear monitor: White/Blue/Green/Amber/Red/Purple/Skyblue/Off
(This function is depended on Over Head Monitor)
Plasmacluster air volume adjustment button*2
Whenever you touch the button, you can change the air volume. Off Low Mid High Off
•While the plasmacluster is operating, the indicator is displayed on the Audio source screen.
Remote Sensor
You can set whether the sensor on Rear monitor receives remote control operation, or the unit receives it.
*1 The visual source that can be output to the Rear monitor is “HDMI/ DVD,” and “AUX.” When the unit plays back the visual source, you can only select the same visual source as the unit.
*2 When the Plasmacluster in “Setting the Rear Seat Entertainment System” (page 50) is set to “Off,” the Plasmacluster air volume adjustment button is not displayed.
•If the same visual source is being output to both the unit and the Rear monitor when an incoming/outgoing call is made, the visual/audio output to the Rear monitor is interrupted temporarily depending on the source.
If different visual sources are being output to the unit and the Rear monitor, visual/audio output to the Rear monitor continues without interrupting playback.
21-EN
In the menu screen, you can select the audio source and perform various setups or operations on the unit.
Press the MENU button.
The menu screen is displayed.
•You can also display the menu screen by touching the lower part of the Audio source screen or by swiping upward.
Menu screen example
Setup button
Displays the Setup screen. (page 30)
Phone button*2
Displays the Phone menu screen. (page 81)
•Depending on the setting and connected devices, the displayed
icons and orders may differ. Touch to display more icons such as [Notifications]*3, [Android Auto]*4, [Apple CarPlay]*5, [Vehicle Info]*6 and [Alpine Connect]*7.
*1 Displays when the Camera Select is set to “Front,” “Rear,” or “Other.” (page 47)
*2 Displays when the Bluetooth setting is set to “On.” (page 31) *3 Use to display the Facebook Notification List on the connected
smartphone via this unit. (page 29)
Displays when Alpine TuneIt App is set to “USB (iPhone)” or “Bluetooth (Android),” and when a smartphone with Alpine TuneIt App installed is connected. (page 28)
*4 Displays the Android Auto screen, displayed when an Android Smartphone installed Android Auto App is connected. (page 52)
*5 Displays the Apple CarPlay screen, displayed when Apple CarPlay is turned on and an iPhone 5 or later is connected. (page 51)
*6 Displays the iDataLink mode screen. (page 95)
*7 Set Connectivity Setting or Alpine Connect to USB (iPhone) or Bluetooth (Android) depending on the connected Smartphone. For details, see “Alpine Connect App (Optional)” (page 52).
Displays the currently playing audio source.
Displays the total number of the audio sources that can be selected. Also displays the current position, counting from the leftmost audio source.
Touch or swipe downward to return to the Audio source screen.
Audio source select area
Touch your desired source icon to change the audio source.
•Swiping to the right or left in the Audio source select area, you can change one audio source at a time. Moreover, swiping to the right or left outside the Audio source select area (upper and lower sides), you can change pages of the Audio source select area.
•The source icon displayed in the Audio source select area is the one checked on the Edit menu screen. For details on how to display/ hide the source icon, see “Edit Menu” (page 22).
Displays Preset No, and information of the Search mode, etc., located in the middle of the Audio source select area.
•Touch the desired preset number or the Search mode to change the audio source directly.
•The displayed information differs depending on the audio source. Some sources are not displayed.
Touch to display more icons. (Displayed only when icons’ number over 5.)
External Accessory Control button
Is displayed when the optional External Accessory Control module is connected and “Setting the External Accessory Control” is set to “On” (page 50).
•You can operate the external accessories from this unit. For details, see “External Accessory Control Operation” (page 97).
Camera button*1
Displays camera images. (page 91)
22-EN
You cannot operate the Edit Menu screen while driving.
Your vehicle must be parked with the ignition key in the ACC or ON position. For details, see “To display the Setup Menu screen” in “Setup Operation” (page 30).
In the Edit Menu screen, you can change the audio source order or set the display/hide settings.
1Touch the desired source icon in the Menu screen for at least 2 seconds.
A checkbox ( or ) is displayed on the upper left area of the source icon and switches to the edit mode.
•The source icon displayed in the Edit Menu screen is displayed only when usable setup and conditions of each Audio source are fulfilled. For details on setup and conditions of each audio source, see “Switching Sources” (page 18).
Changing the order of Audio source
Drag and drop the source icon to the desired location.
Hiding/Displaying Audio source
Place a check in the checkbox () to display the Audio source icon. Uncheck the checkbox () to hide it.
• You cannot hide the icon of a source that is currently playing.
2Touch [Done].
The editing content is confirmed, and returns to the menu screen.
•Editing here is reflected in the order of (AUDIO) button touching and change of the Audio source. (page 18)
The Indicator Bar at the bottom of the screen displays various types of information, like the current time.
Lights up when connected to a Bluetooth compatible device. (Does not display when connection is set to OFF.)
: Bluetooth connection to audio device
: Bluetooth connection to Hands Free Phone Blinks while reconnecting.
Indicates the battery level of the connected Bluetooth device*.
Battery |
Level 3 |
Level 2 |
Level 1 |
No Battery |
|
Level |
|||||
|
|
|
|
||
|
|
|
|
|
|
Icon |
|
|
|
|
|
|
|
|
|
|
This may not be displayed depending on the connected Bluetooth device. Whenever one battery level decreases, the alarm sounds.
Indicates the signal strength level of the connected Bluetooth compatible device*.
Displayed when Bluetooth setting is ON.
0 |
1 |
2 |
3 |
No Service |
|
|
|
|
|
|
|
|
|
|
Plasmacluster indicator
Indicates the setting value (Low/Mid/High) selected in “Plasmacluster air volume adjustment.”
The clock display
You can switch between the 12 hour display and 24 hour display options.
For details of navigation operations, refer to “Navigation System OM” in the website at http://www.alpine-usa.com.
Bluetooth devices Name*
*When you connect two Hands-Free Phones, the information of the Bluetooth device set to Primary is displayed.
You can set a BMP image that is stored on a USB flash drive as the opening screen.
This setting requires the following image format, folder name and file name.
Usable file format:
-BMP image
-Image size: 800 × 480 pixels (RGB 24 bit or less/number of color bit: 24, 8, 1 bit)
-Compression format: non-compressed
-Folder name*1: OPENINGFILE
-File name*2: openingfile.bmp
1 Connect the USB flash drive to the USB extension cable.
A message confirming the opening screen change is displayed.
2Touch [OK].
An update indicator “ (Loading)” is displayed, and update for the opening screen starts.
3After the update is complete, the following message is displayed.*3
“The logo has been updated successfully! Please remove Flash Memory and press OK.”
4After removing the USB flash drive, touch [OK].
The opening screen setting is complete.
*1 Be sure to save the folder to the first layer of the USB flash drive. *2 Only one BMP image can be set as the opening screen.
*3 If “Customization failed,” is displayed, touch [OK] and then check that the folder name, file name and file format are correct.
•Do not perform the following actions during the update.
-Do not turn off the ACC to the car.
-Do not unplug the USB flash drive.
-Do not turn off or operate the unit.
•To return the opening screen to its original image, you must Clear All Settings. Be careful of this operation, as your other settings are also initialized. For details, see “Initializing the System” (page 42).
23-EN
The displayed screens and procedures may vary slightly depending on the function used, but the basic input method is the same.
Input screen area.
Cursor position alteration switch Cancel
Keypad mode finishes.
(Delete)
Returns to the previous character and erases it.
Touching here for more than 2 seconds will erase all input characters.
Input number is confirmed. Character keypad
Space
Special character selector switch
The Alphanumeric/Special characters/Symbols selection popup is displayed.
Touch the desired character type.
24-EN
This unit enables you to recall functions easily by registering frequently used items such as the Audio source, the navigation search function, etc. to the Favorite screen. You can recall any of these items easily.
1Press the (Favorite) button.
The Favorite screen is displayed.
Favorite screen example
Changes to the Edit screen used for registering items or changing names.
Favorite registration item
Swipe to the left and right to change the pages. You can add up to 6 pages.
Indicates the location of the currently displayed Favorite screen.
2Touch your desired Favorite registered item.
The desired item is displayed.
•When making a phone call by choosing shortcut dialing, after the message of confirmation of outgoing phone calls is displayed, touch [Call]. For details, see “Calling by Favorite Function” (page 83).
You cannot edit the Favorites screen while driving.
Your vehicle must be parked with the ignition key in the ACC or ON position. For details, see “To display the Setup Menu screen” in “Setup Operation” (page 30).
1Touch [] (Edit).
A checkbox is displayed on the upper left area of the registration icon and it changes to Edit mode.
Setting item:
Item registration / Item name change / Icon change / Layout change / Item deletion
2After editing is complete, touch [] (Back).
3After the caption for the confirmation is displayed, touch
[OK].
4Editing is complete and the screen switches to the Favorite screen.
•If you touch [] (Cancel) while editing, the edits are reset and the screen returns to the previous Edit screen.
1Touch [] (Add).
The items to be added (categories) are displayed.
2Touch the desired item to be added (category).
3Choose the desired item to be added.
•You can add up to 54 items.
•You cannot register an item more than once.
25-EN
Audio/Visual
[Radio]*1 / [USB/iPod] / [Factory Media (USB/iPod)]*2 / [HDMI/DVD] / [Pandora] / [Bluetooth Pandora] / [SiriusXM]*3 or [Factory SiriusXM]*2, 3 / [AUX]*4 / [Bluetooth Audio] / [Apple CarPlay]*5 / [Android Auto]*5
*1 Choose a frequency from Preset 1 - 12 in any of the tuner preset bands. *2 Not displayed when your car does not support the source or “Setting the Source Category” (page 49) is set to “Aftermarket.” This is also not
displayed when the iDataLink module is not connected. *3 You can choose a channel registered to Presets 1 - 18.
*4 When “AUX” is selected, the source name set in “Setting the Auxiliary (AUX) Name” (page 45) is also displayed in the Favorite screen. When the iDataLink module (sold separately) is connected, the Auxiliary (AUX) mode is not available.
*5 You can register now playing Apple CarPlay Music or Google Play Music depending on the connected Smartphone.
•When using Apple CarPlay, some option may not available.
•You can also register directly by touching [ ] in the Audio source screen.
However, if it is already registered, [ ] is not displayed.
Navigation
[Specific Place]:
You can display places registered in Favorite and set your destination.
[Quick Place Search]:
Displays the address search keypad. [Help Nearby]:
Displays the nearby search screen. [Place Categories]:
Displays the selected Place Categories list.
•For details of navigation operations, refer to “Navigation System OM” in the website at http://www.alpine-usa.com.
Phone (Shortcut Dialing)*6
You can register the user’s shortcut dialing stored in the Phone Book.
•If multiple phone numbers are stored, select a number you want to register.
•You can register directly by touching [ ] of the Contacts list. (page 81)
•You can change the icon you registered. (page 26)
*6 You can only select Phone when a mobile phone is connected.
For details on how to register a mobile phone and downloading Phone Book, see “Bluetooth Operation” (page 81).
1Touch the text area of the registered item.
The Input User Name screen (Keypad) is displayed.
2Input the name and touch [OK].
•For details on how to input characters using the keypad, see “How to Input Characters and Numbers (Keypad)” (page 24).
You can change the icons of Shortcut Dialing and Navigation category. The following example explains how to change the Shortcut Dialing icon. Perform the same procedure to change the Navigation category icon.
1Touch the icon that you want to change.
The icon list is displayed.
2Touch the icon you want to change from the icon list.
The icon is changed to the selected icon.
26-EN
Drag and drop the item to the desired location.
The item location is changed.
•When you move to other pages, switch pages, or when you make a new page and move to another, drag to the end of the screen, and lift your finger after the page changes.
When deleting a selected item
1Touch the checkbox at the left of the item you want to delete and place a check () in it.
2Touch [] (Delete).
The selected item will be deleted.
When deleting all items
Touch [ ] (Delete All).
All items are deleted.
27-EN
Applying Alpine
TuneIt App
This unit’s sound tuning is programmable from a connected Smartphone. It is also possible to download specific parameters for certain vehicles from Alpine’s TuneIt database stored in the Cloud. Using the Alpine TuneIt App, customized parameters can also be uploaded for others to share and rate.
Through this unit, it is also possible to receive and respond to information from Alpine’s Social Network Service (SNS) available through the connected Smartphone.
The installed Alpine TuneIt App should be launched on the Smartphone before connection to the head unit.
Alpine TuneIt App, is downloadable from Apple’s App Store; the Android user can download it from Google Play™. For details, consult your Alpine dealer.
Before these operations, set TuneIt to USB (iPhone) or Bluetooth (Android) depending on the connected Smartphone. For details, see “Smartphone Apps Setup” (page 51).
•The application program and related specifications and data may be deleted or terminated without notice.
•Some Alpine TuneIt App functions may not be available if the Smartphone is not in a service area or receives no signal.
•Turn Apple CarPlay to Off before using Alpine TuneIt App. Refer to “Apple CarPlay Setup” (page 46).
After setting the above procedure, you can adjust the unit’s sound function on the Smartphone.
1Make sure the unit is powered on.
2Launch the Alpine TuneIt App on the Smartphone. Adjust the unit’s sound accordingly on the Smartphone.
•The setting cannot be done on both the Smartphone and this unit at the same time. While the sound function of this unit is set via Smartphone, the sound function settings on the unit will be displayed as “Sound APP Connected.”
•In some situations, such as the unit is powered off or during a call, etc., sound setting cannot be done via the Smartphone.
•This function may not be available depending on the paired Smartphone.
•Please obey all local traffic laws while using this function.
•When “Setting the External Audio Processor” (page 50) “On,” this function is not available.
Some functions may be available in a future version of Alpine TuneIt App.
•Depending on the paired Smartphone, the following functions may not be available even though the Alpine TuneIt App version is updated.
Receiving Notification
When the smartphone connected to the unit receives new notifications from Facebook, the unit emits a notification sound or displays the notification screen. Set this up in the Alpine TuneIt App settings.
Notification Incoming screen example
Poster’s picture and name
Touch here to switch to Facebook screen. Facebook screen is not displayed while driving.
Read (Stop) button
Touch to play the notification using TTS (Text to Speech) (Depending on the status, operation may not be available). During TTS play mode, touch [Stop] to stop play.
Like button
For “Like” operation. (Valid when Wall Posts or Comments is received)
Notifications button
Touch to switch to Notifications List screen.
Close button
Close the notification screen.
Touch the desired button to operate.
•A new received Notification prompt will last for 15 seconds. If there is no operation within 15 seconds, the unit will return to normal mode.
•Touching current main screen will close the notification screen.
•Volume adjustment during TTS play can be adjusted by / or / (0-35). Settings will be reflected at the next TTS reproduction.
•The TTS volume is output via the car’s front right and left speakers.
28-EN
Displaying Facebook Screen
During Notification incoming or Notification List screen, you can switch to Facebook screen.
Facebook screen example
Message content
Poster’s photo
Close button: Close the Facebook screen.
Touch the poster’s picture and name to switch to the Facebook screen.
The detailed information of Notification is displayed.
•Touch [ ] (Back) to return to Notifications List screen.
•Depending on the status, contents of message and photo may not be displayed.
•In some situations, such as the unit is powered off or during a call, etc., Notification of the Smartphone will not be prompted by this unit.
•Facebook screen is not displayed while driving.
Displaying Notification List
You can view the received Notification from Facebook in the connected Smartphone via this unit.
Notification List screen example
Poster’s Name and Message
Messages are not displayed while driving.
Touch [Read All]/[Stop] to play/stop all Notifications.
•You can switch to the Notification List screen from the Menu screen.
•Touch [ ] to return to Current screen.
•Depending on the status, some functions may not be available.
•The displayable amount of the Notification list depends on the connected Smartphone.
29-EN
To display the Setup Menu screen:
Your vehicle must be parked with the ignition key in the ACC or ON position. To do this, follow the procedures below.
1Bring your vehicle to a complete stop at a safe location. Engage the parking brake.
2Release the parking brake. (For safety, release the parking brake while depressing the foot brake pedal).
3Engage the parking brake again.
•For automatic transmission vehicles, place the transmission lever in the Park position.
Now, the locking system for the Setup operation has been released. Engaging the parking brake can reactivate the Setup Menu, as long as the car’s ignition has not been turned off. It is not necessary to repeat the above procedure (1 through 3) of “To display the Setup Menu screen.”
Each time the ignition is turned OFF, perform the procedure of “To display the Setup Menu screen.”
1Press the MENU button.
The Menu screen is displayed.
•You can also display the menu screen by touching the lower part of the Audio source screen or by swiping upward.
[Setup] button
2Touch [Setup].
The Setup main screen is displayed.
3Touch the required setting icon on the upper part of the Setup main screen or swipe the list area vertically, then touch the setting item.
Setting items:
Wireless: See “Wireless (Bluetooth) Setup” (page 31).
General: See “General Setup” (page 33).
Source: See “Source Setup” (page 43).
System: See “System Setup” (page 46).
30-EN