Allied Telesis AT-8000S User Manual 2

0 (0)

Layer 2

Ethernet Switch

Allied Telesis AT-8000S

Installation Guide

AT-8000S Series Stackable Gigabit Ethernet Switches

613-001106 Rev C

Copyright 2011 Allied Telesis, Inc.

All rights reserved. No part of this publication may be reproduced without prior written permission from Allied Telesis, Inc.

Allied Telesis and the Allied Telesis logo are trademarks of Allied Telesis, Incorporated. All other product names, company names, logos or other designations mentioned herein are trademarks or registered trademarks of their respective owners.

Allied Telesis, Inc. reserves the right to make changes in specifications and other information contained in this document without prior written notice. The information provided herein is subject to change without notice. In no event shall Allied Telesis, Inc.be liable for any incidental, special, indirect, or consequential damages whatsoever, including but not limited to lost profits, arising out of or related to this manual or the information contained herein, even if Allied Telesis, Inc. has been advised of, known, or should have known, the possibility of such damages.

Table of Contents

Table of Contents

 

Preface....................................................................................................................................

6

How This Guide is Organized..........................................................................................................

6

Document Conventions ...................................................................................................................

6

Product Description.................................................................................................................

8

Features ..........................................................................................................................................

9

IEEE Standards ...............................................................................................................................

9

AT-8000S/16 Front Panel..............................................................................................................

10

AT-8000S/16 Back Panel ..............................................................................................................

10

AT-8000S/24 Front Panel..............................................................................................................

11

AT-8000S/24 Back Panel ..............................................................................................................

11

AT-8000S/24POE Front Panel ......................................................................................................

12

AT-8000S/24POE Back Panel.......................................................................................................

12

AT-8000S/48 Front Panel..............................................................................................................

13

AT-8000S/48 Back Panel ..............................................................................................................

13

AT-8000S/48POE Front Panel ......................................................................................................

14

AT-8000S/48POE Back Panel.......................................................................................................

14

Ports Description ...........................................................................................................................

15

10/100Base-T Fast Ethernet Ports ..........................................................................................................

15

10/100/1000Base-T Uplink Ethernet Ports ..............................................................................................

15

SFP Port ..................................................................................................................................................

15

DB-9 Console Port...................................................................................................................................

15

LED Definitions..............................................................................................................................

15

Front Panel LEDs ....................................................................................................................................

15

Port LEDs ................................................................................................................................................

17

24/48 Port Device System LEDs .............................................................................................................

20

Stacking Ports LEDs................................................................................................................................

21

Installation.............................................................................................................................

22

Preparing for Installation................................................................................................................

22

Safety Precautions...................................................................................................................................

22

Site Requirements ...................................................................................................................................

24

Unpacking................................................................................................................................................

24

Installing the Device ......................................................................................................................

25

Desktop or Shelf Installation ....................................................................................................................

25

Rack Installation ......................................................................................................................................

26

Connecting the Device ..................................................................................................................

27

Connecting the Switch to a Terminal .......................................................................................................

27

AC Power Connection .............................................................................................................................

28

Page 3

Allied Telesis AT-8000S Switch

Switch Installation Guide

Stacking ................................................................................................................................

30

Understanding the Stack Topology ...............................................................................................

30

Stacking Chain Topology ..............................................................................................................

31

Stacking Members and Unit ID .....................................................................................................

31

Configuring Stacking.....................................................................................................................

32

Initial Configuration ...............................................................................................................

34

Configuration Overview.................................................................................................................

34

Configuration.................................................................................................................................

34

Static IP Address and Subnet Mask .......................................................................................................

34

User Name..............................................................................................................................................

35

Troubleshooting ....................................................................................................................

36

Technical Specifications .......................................................................................................

38

Physical Specifications ...........................................................................................................................

38

Weight.....................................................................................................................................................

38

Environmental Specifications..................................................................................................................

38

Power Specifications...............................................................................................................................

38

Safety and Electromagnetic Emissions Certifications.............................................................................

38

Compliance Standards............................................................................................................................

39

Cable, Port, and Pinout Information........................................................................................................

39

Pin Connections for the 10/100/1000 Ethernet Interface ........................................................................

39

Safety Statements.................................................................................................................

42

Laser Safety Notices .....................................................................................................................

42

Electrical Safety Notices ...............................................................................................................

42

Telecommunications Compliance Notices ....................................................................................

47

Page 4

Table of Contents

Page 5

Allied Telesis AT-8000S Switch

Installation Guide

Preface

This guide contains the hardware installation instructions for the AT-8000S/16, AT-8000S/24, AT-8000S/24POE, AT-8000S/48 and AT-8000S/48POE Fast Ethernet Switches.

How This Guide is Organized

This manual contains the following chapters:

Chapter 1 Product Description describes the features and components of the switches.

Chapter 2 Installation describes the installation instructions for the switches.

Chapter 3 Stacking describes the stacking instructions for the switches.

Chapter 4 Initial Configuration describes the instructions for initially configuring the switches.

Chapter 5 Troubleshooting provides information on how to resolve problems that might occur with the switches.

Appendix A Technical Specifications contain the technical specifications for the switches.

Appendix B Translated Safety Standards contain the safety standards for the device.

Document Conventions

This document uses the following conventions to highlight important information:

Note

Notes provide additional information.

Caution

Cautions inform you that performing or omitting a specific action may result in equipment damage or loss of data.

Warning

Warnings inform you that performing or omitting a specific action may result in bodily injury.

Page 6

Contacting Allied Telesis

Contacting Allied Telesis

This section provides Allied Telesis contact information for technical support as well as sales or corporate information.

Online Support You can request technical support online by accessing the Allied Telesis Knowledge Base from the following web site: www.alliedtelesis.com/kb. You can use the Knowledge Base to submit questions to our technical support staff and review answers to previously asked questions.

Email and Telephone

Support

Returning Products

For Sales or

Corporate

Information

Warranty

For Technical Support via email or telephone, refer to the Allied Telesis web site: www.alliedtelesis.com. Select your country from the list displayed on the website. Then select the appropriate menu tab..

Products for return or repair must first be assigned a Return Materials Authorization (RMA) number. A product sent to Allied Telesis without a RMA number will be returned to the sender at the sender’s expense.

To obtain an RMA number, contact the Allied Telesis Technical Support group at our web site: www.alliedtelesis.com/support/rma. Select your country from the list displayed on the website. Then select the appropriate menu tab..

You can contact Allied Telesis for sales or corporate information at our web site: www.alliedtelesyn.com. Select your country from the list displayed on the website. Then select the appropriate menu tab.

Go to the Allied Telesis web site at www.alliedtelesis.com/warranty for the AT8000S hardware warranty information.

Page 7

Allied Telesis AT-8000SSwitch

Switch Installation Guide

Chapter 1. Product Description

The new AT-8000S series combines the best of the previous L2 series; stackability and affordability.

The new AT-8000S series is an entry level managed switch for the SMB, Small Office/Field Office offering managed desktop connectivity. The fiber uplink provides connectivity between workgroups over a larger distances. In addition the AT-8000S series is also equipped with a copper 10/100/1000Base-T port for connectivity to gigabit aggregation switches.

The new AT-8000S series combines value with the necessary management features for networked applications. There are five device models which provide different hardware configurations and include the following:

AT-8000S/16 device which supports 16 built-in 10/100Base-T ports, and a Combo port functionality that supports both copper and SFP interfaces.

AT-8000S/24 device with stacking ports which supports 24 built-in 10/100Base-T ports, two Gigabit stackable and 2 Combo Ports, inclusive of a Combo port functionality that supports both copper and SFP interface.

AT-8000S/24POE device with stacking port which supports 24 built-in 10/100Base-T ports, two Gigabit stackable and 2 Combo Ports, inclusive of a Combo port that supports both copper and SFP interface. The PoE function is supported on RJ-45 ports.

AT-8000S/48 device with stacking ports which supports 48 built-in 10/100Base-T ports, two Gigabit stackable and 2 Combo Ports, inclusive of a Combo port functionality that supports both copper and SFP interface.

AT-8000S/48POE device with stacking port which supports 48 built-in 10/100Base-T ports, two Gigabit stackable and 2 Combo Ports, inclusive of a Combo port that supports both copper and SFP interface. The PoE function is supported on RJ-45 ports.

The AT-8000S/24, AT-8000S/24POE, AT-8000S/48 and AT-8000S/48POE can be joined together into a stack of up to six units. For more information, see Chapter 3 Stacking.

Device configuration is performed through an Embedded Web Server (EWS) or through a Command Line Interface (CLI). The device management is performed through a DB-9 RS-232 interface.

Page 8

Product Description

Features

The AT-8000S/16, AT-8000S/24, AT-8000S/24POE, AT-8000S/48 and AT-8000S/48POE features include the following:

Wirespeed switching traffic across all ports

Auto MDI/MDIX enabled

802.1d, 1w, 1s priority tags supported

Broadcast storm control

IEEE 802.1Q tagged VLANs supported

GARP/GVRP supported

Port/MAC based VLANs supported

802.3ad link aggregation Static and Dynamic (LACP) supported

IEEE 802.1P based QoS supported

Ingress rate limiting

Egress rate shaping (WRR)

802.1x port/MAC based authentication support

RFC 2618 RADIUS Authentication

SSL/ SSLv3

RFC 1492 TACACS+

Management ACL support

Industry standard CLI

Browser based management interface (HTTP)

Telnet access supported

SNMP v1, v2 and v3

RFC1757 RMON support

Port Mirroring support

PVE

Port Security

DHCP support

Static IP Multicast support

IGMP Snooping

IEEE Standards

IEEE 802.3 10Base-T

IEEE 802.3u 100Base-TX

IEEE 802.3ab — 1000Base-TX Gigabit Ethernet

IEEE 802.3z — Full Duplex

IEEE 802.3u — Auto-Negotiation

IEEE 802.3x — Flow Control, Symmetric and Asymmetric

Page 9

Allied Telesis AT-8000SSwitch

Switch Installation Guide

AT-8000S/16 Front Panel

The following figure illustrates the AT-8000S/16 front panel.

Figure 1: AT-8000S/16 Front Panel

The AT-8000S/16 front panel is configured as follows:

16 10/100Mbps Ports — RJ-45 ports designated as 10/100Base-T. The RJ-45 ports are designated as ports Ports 1 - 16.

1 10/100/1000Base-T Copper Port — There is one copper 10/100/100Base-T port designated on the switch as port 17R. This port is paired with the SFP slot designated on the switch as port 17. Together these two ports form the Combo ports shown in Figure 1.

1 SFP Port — There is one SFP slot supports either a 100Base-FX or a 1000Base-X (fiber) connection and is designated on the switch as port 17. This SFP slot is paired with the 10/100/1000Base-T copper port which is designated on the switch as port 17R. Together these two ports form the Combo ports shown in Figure 1.

DB-9 Console port — An asynchronous serial console port supporting the RS-232 electrical specification. The port is used to connect the device to the console managing the device.

Reset Button — Button to reset the device.

Mode Button — Selects the port LED indications.

AT-8000S/16 Back Panel

The following figure illustrates the AT-8000S/16 back panel.

Figure 2: AT-8000S/16 Back Panel

The AT-8000S/16 back panel is configured as follows:

Power Connector — AC power supply interface.

Page 10

Product Description

AT-8000S/24 Front Panel

The following figure illustrates the AT-8000S/24 front panel.

Figure 3: AT-8000S/24 Front Panel

The AT-8000S/24 front panel is configured as follows:

24 10/100Mbps Ports — RJ-45 ports designated as 10/100Base-T. The RJ-45 ports are designated as ports Ports 1 - 24.

2 10/100/1000Base-T Copper Ports — There are two copper 10/100/100Base-T ports designated on the switch as ports 25R and 26R. These ports are paired with the two SFP slots designated on the switch as ports 25 and 26. Together these four ports form the Combo ports shown in Figure 3.

2 SFP Ports— There are two SFP slots which support either a 100Base-FX or a 1000Base-X (fiber) connection and are designated on the switch as ports 25 and 26. This SFP slot is paired with the two 10/100/ 1000Base-T copper ports which is designated on the switch as port 25R and 26R. Together these four ports form the Combo ports shown in Figure 3.

DB-9 Console port — An asynchronous serial console port supporting the RS-232 electrical specification. The port is used to connect the device to the console managing the device.

Reset Button — Button to reset the device.

Mode Button — Selects the port LED indications.

AT-8000S/24 Back Panel

The following figure illustrates the AT-8000S/24 back panel.

Figure 4: AT-8000S/24 Back Panel

The AT-8000S/24 back panel is configured as follows:

Power Connector — AC power supply interface.

2 Stacking Ports — Two RJ-45 ports device stacking.

Page 11

Allied Telesis AT-8000SSwitch

Switch Installation Guide

AT-8000S/24POE Front Panel

The following figure illustrates the AT-8000S/24POE front panel.

Figure 5: AT-8000S/24POE Front Panel

The AT-8000S/24POE front panel is configured as follows:

24 10/100Mbps Ports — RJ-45 ports designated as 10/100Base-T. The RJ-45 ports are designated as ports Ports 1 - 24.

2 10/100/1000Base-T Copper Ports — There are two copper 10/100/100Base-T ports designated on the switch as ports 25R and 26R. These ports are paired with the two SFP slots designated on the switch as ports 25 and 26. Together these four ports form the Combo ports shown in Figure 5.

2 SFP Ports— There are two SFP slots which support either a 100Base-FX or a 1000Base-X (fiber) connection and are designated on the switch as ports 25 and 26. This SFP slot is paired with the two 10/100/ 1000Base-T copper ports which is designated on the switch as port 25R and 26R. Together these four ports form the Combo ports shown in Figure 5.

DB-9 Console port — An asynchronous serial console port supporting the RS-232 electrical specification. The port is used to connect the device to the console managing the device.

Reset Button — Button to reset the device.

AT-8000S/24POE Back Panel

The following figure illustrates the AT-8000S/24POE back panel.

Figure 6: AT-8000S/24POE Back Panel

The AT-8000S/24POE device back panel is configured as follows:

Power Connector — AC power supply interface.

2 Stacking Ports — Two RJ-45 ports device stacking.

Page 12

Allied Telesis AT-8000S User Manual 2

Product Description

AT-8000S/48 Front Panel

The following figure illustrates the AT-8000S/48 front panel.

Figure 7: AT-8000S/48 Front Panel

The AT-8000S/48 device front panel is configured as follows:

48 10/100Mbps Ports — RJ-45 ports designated as 10/100Base-T. The RJ-45 ports are designated as ports Ports 1 - 48.

2 10/100/1000Base-T Copper Ports — There are two copper 10/100/100Base-T ports designated on the switch as ports 49R and 50R. These ports are paired with the two SFP slots designated on the switch as ports 49 and 50. Together these four ports form the Combo ports shown in Figure 7.

2 SFP Ports — There are two SFP slots which support either a 100Base-FX or a 1000Base-X (fiber) connection and are designated on the switch as ports 49 and 50. This SFP slot is paired with the two 10/100/ 1000Base-T copper ports which is designated on the switch as port 49R and 50R. Together these four ports form the Combo ports shown in Figure 7.

Mode Button — Selects the port LED indications.

AT-8000S/48 Back Panel

The following figure illustrates the AT-8000S/48 back panel.

Figure 8: AT-8000S/48 Back Panel

The AT-8000S/48 back panel is configured as follows:

Power Connector — AC power supply interface.

2 Stacking Ports — Two RJ-45 ports device stacking.

Reset Button — Button to reset the device.

DB-9 Console port — An asynchronous serial console port supporting the RS-232 electrical specification. The port is used to connect the device to the console managing the device.

Page 13

Allied Telesis AT-8000SSwitch

Switch Installation Guide

AT-8000S/48POE Front Panel

The following figure illustrates the AT-8000S/48POE front panel.

Figure 9: AT-8000S/48POE Front Panel

The AT-8000S/48 device front panel is configured as follows:

48 10/100Mbps Ports — RJ-45 ports designated as 10/100Base-T. The RJ-45 ports are designated as ports Ports 1 - 48.

2 10/100/1000Base-T Copper Ports — There are two copper 10/100/100Base-T ports designated on the switch as ports 49R and 50R. These ports are paired with the two SFP slots designated on the switch as ports 49 and 50. Together these four ports form the Combo ports shown in Figure 9.

2 SFP Ports — There are two SFP slots which support either a 100Base-FX or a 1000Base-X (fiber) connection and are designated on the switch as ports 49 and 50. This SFP slot is paired with the two 10/100/ 1000Base-T copper ports which is designated on the switch as port 49R and 50R. Together these four ports form the Combo ports shown in Figure 9.

AT-8000S/48POE Back Panel

The following figure illustrates the AT-8000S/48POE back panel.

Figure 10: AT-8000S/48POE Back Panel

The AT-8000S/48POE back panel is configured as follows:

Power Connector — AC power supply interface.

2 Stacking Ports — Two RJ-45 ports device stacking.

Reset Button — Button to reset the device.

DB-9 Console port — An asynchronous serial console port supporting the RS-232 electrical specification. The port is used to connect the device to the console managing the device.

Page 14

Product Description

10/100Base-T Fast Ethernet Ports

Ports Description

10/100Base-T Fast Ethernet Ports

The 10/100Base-T Fast Ethernet ports are RJ-45. The 10/100 Mbps port supports halfand full-duplex mode.

10/100/1000Base-T Uplink Ethernet Ports

The 24/48 port devices contains two 10/100/100Base-T Gigabit ports, and the 16 port device contains one 10/100/100Base-T port. The RJ-45 1000 Mbps port supports 1000 mbps in full-duplex mode and 10/100 mbps halfand full-duplex mode.

SFP Port

Small Form Factor Pluggable (SFP) Optical Transceivers are integrated duplex data links for bi-directional communication over optical fiber, designed for high-speed Fiber Channel data links. The SFP port is designated as 1000Base-FX.

DB-9 Console Port

The DB-9 port is an asynchronous serial console port supporting the RS-232 electrical specification. The port is used to connect the device to a console managing the device. This interface configuration is as follows:

Eight data bits.

One stop bit.

No parity.

Baud rate is 115,200 (default). The user can change the rate from 115,200 down to 2400 bps.

LED Definitions

The device front panels contain Light Emitting Diodes (LED) that indicate the device status. The different LED types are as follows:

Port LEDs — Indicates each port status.

Power LED — Indicates the device power supply status.

Mode LEDs — Indicates which information the LED displays - only on non-PoE devices.

Stacking LEDs — Indicates the device location in a stack.

Front Panel LEDs

The front panels have two types of LEDs, excluding the LEDs attached to the ports. The two types are as follows:

Mode LEDs — Indicates which information the LED displays.

Stacking LEDs — Indicates the device location in a stack.

Page 15

Loading...
+ 33 hidden pages