Allied Telesis AT-AR020 PRI EI-TI, AT-AR021SBRI-S-I, AT-AR027VOLP-FXS User Manual

0 (0)
Allied Telesis AT-AR020 PRI EI-TI, AT-AR021SBRI-S-I, AT-AR027VOLP-FXS User Manual

Port Interface Card

Installation and Safety Guide

AT-AR020 PRI E1/T1 AT-AR021 (S) BRI-S/T AT-AR021 (U) BRI-U AT-AR022 ETH AT-AR023 SYN AT-AR024 ASYN4 AT-AR026 4ETH AT-AR027 VoIP-FXS

Port Interface Card

Installation and Safety Guide

AT-AR020 PRI E1/T1

AT-AR021(S) BRI-S/T

AT-AR021(U) BRI-U

AT-AR022 ETH

AT-AR023 SYN

AT-AR024 ASYN4

AT-AR026 4ETH

AT-AR027 VoIP-FXS

Download the complete document set from www.alliedtelesis.com/support/software

2

Port Interface Card

Port Interface Card Installation and Safety Guide

Document Number 613-000601 Rev C.

© 2007 Allied Telesis, Inc. All rights reserved. No part of this publication may be reproduced without prior written permission from Allied Telesis, Inc.

Allied Telesis, Inc. reserves the right to change specifications and other information in this document without prior written notice. The information provided herein is subject to change without notice. In no event shall Allied Telesis, Inc. be liable for any incidental, special, indirect, or consequential damages whatsoever, including but not limited to lost profits, arising out of or related to this manual or the information contained herein, even if Allied Telesis, Inc. has been advised of, known, or should have known, the possibility of such damages.

Allied Telesis and AlliedWare are trademarks or registered trademarks in the United States and elsewhere of Allied Telesis, Inc. Adobe, Acrobat, and Reader are either registered trademarks or trademarks of Adobe Systems Incorporated in the United States and/or other countries. Microsoft and Visio are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. Additional brands, names and products mentioned herein may be trademarks of their respective companies.

Installation and Safety Guide

3

About this Guide

Port Interface Cards (PICs) are a cost effective and flexible mechanism for adding new or additional network interfaces to your switch or router.

This Installation and Safety Guide describes how to install the following PICs:

AT-AR020 PRI E1/T1, a single ISDN Primary Rate E1/T1 interface

AT-AR021(S) BRI-S/T, a single ISDN Basic Rate S/T interface

AT-AR021(U) BRI-U, a single ISDN Basic Rate U interface

AT-AR022 ETH, a dual Ethernet 10BASE-T/AUI port

AT-AR023 SYN, a single 2Mbps synchronous interface

AT-AR024 ASYN4, four asynchronous ports

AT-AR026 4ETH, four Ethernet 10BASE-T ports

AT-AR027 VoIP-FXS, two Foreign Exchange Voice over IP ports

You can download the complete documentation for Port Interface Cards from www.alliedtelesis.com/support/software. For more information about the documentation and other resources, see “Obtaining Documentation and Resources” on page 11.

Compatible Switches and Routers

You can install a PIC into a PIC bay on the base unit of your switch or router, or into a PIC bay on an AT-AR040 NSM (Network Service Module) installed in your switch or router.

The following table shows which PICs are appropriate for different expansion bays and models of switch and router.

This expansion bay ...

Accepts ...

 

 

PIC bays in the AR415S, AR440S, AR441S,

All PICs.

AR442S, AR725, and AR745 router

 

 

 

PIC bays in the AR750S, AR750S-DP, and

AT-AR020, AT-AR021, AT-AR023,

AR770S router

and AT-AR024.

 

 

AT-AR040 NSM in the AR745 router,

All PICs except AT-AR022 and

Rapier 16fi and Rapier 24i switch

AT-AR026.

 

 

AT-AR040 NSM in the Rapier 48w switch

AT-AR020, AT-AR021, and AT-AR024.

 

 

The AT-AR021(S) V3 hardware revision, identified by the label “AR021v3” on the board, requires a switch or router running AlliedWare® Operating System version 2.9.1-13 or later.

Loading...
+ 9 hidden pages