d
OPERATING INSTRUCTIONS MANUAL DE INSTRUCCIONES MODE D’EMPLOI
CT-X410 YU
STEREO CAR CASSETTE RECEIVER RADIO-CASSETTE ESTEREOFONICO PARA AUTOMOVIL
ENGLISH
ESPAÑOL
FRANÇAIS
OWNER’S RECORD
For your convenience, record the model number and serial number (you will find them on the right side of your set) in the space provided below. Please refer to them when you contact your AIWA dealer in case of difficulty.
Model No. CT-X410
Serial No.
Welcome
Thank you for your purchasing this AIWA product.
To optimize the performance of this unit, please read through this manual carefully.
In addition to this operating instructions manual, be sure to refer to the separate installation and connections manuals as well.
PRECAUTIONS
•This unit is designed to be operated on a 12-volt DC negative-ground electrical system only.
•To prevent short-circuiting, disconnect the negative car battery terminal until the unit has been mounted and connected completely.
•When replacing the fuse, be sure to use one whose amperage rating is identical. Use of a fuse of higher amperage may cause serious damage to the unit.
•Keep screwdrivers, etc. and other metallic or magnetic objects away from the playback head.
•When your car was parked in direct sunlight resulting in a considerable rise in temperature inside the car, allow the unit to cool off before operating it.
•Keep the volume at such a level that you can hear outside warning sounds (horns, sirens, etc.).
Notes on cassettes
Do NOT expose cassettes to direct sunlight, extremely high or cold temperature or moisture. Keep cassettes away from equipment with builtin magnets to avoid unwanted noise or loss of sound quality.
Do NOT touch the tape of a cassette, as any dirt or dust will contaminate the heads.
Be sure to remove any cassette from the unit if you are not using it.
NOTE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/
TV technician for help.
CAUTION
Modifications or adjustments to this product, which are not expressly approved by the manufacturer, may void the user’s right or authority to operate this product.
Caution on the transit protection pad
The unit is shipped with a transit protection pad in the cassette compartment.
Be sure to press EJECT z to remove the pad before operating the unit.
Transit protection pad
1 ENGLISH
CTX410(YU)-total-En-2
TABLE OF CONTENTS |
|
PARTS AND CONTROLS .................................................................................................................. |
3 |
DETACHING AND ATTACHING THE FRONT PANEL ...................................................................... |
4 |
SETTING THE CLOCK ....................................................................................................................... |
5 |
RADIO OPERATION .......................................................................................................................... |
5 |
PRESETTING STATIONS .................................................................................................................. |
6 |
MY INFORMATION SWITCH ............................................................................................................. |
8 |
TAPE PLAYBACK ............................................................................................................................... |
9 |
SOUND ADJUSTMENTS ................................................................................................................. |
10 |
CONNECTING A PORTABLE CD/MD/MP3 PLAYER OR OTHER EQUIPMENT ........................... |
12 |
SETTING THE BEEP TONE ............................................................................................................. |
13 |
MAINTENANCE ................................................................................................................................ |
13 |
SPECIFICATIONS ............................................................................................................................ |
14 |
ENGLISH
ENGLISH 2
CTX410(YU)-total-En-3
PARTS AND CONTROLS
Front panel
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Display window |
|
Rear panel |
|
|
|
|
|
|
||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Front panel |
Display window |
1FUNC (function) button |
&Band indicator |
2PWR (power on/off)/MUTE button |
*VOL (volume) indicator |
3Jog Dial |
(BASS (bass) indicator |
4z(eject) button |
)TRE (treble) indicator |
5TUNE ibutton |
-BAL (balance) indicator |
6TUNE kbutton |
=FAD (fader) indicator |
7Cassette compartment |
qMUTE indicator |
8DIRECTION f/gbutton |
wMY INFO (My Information) indicator |
9A.ME (Auto Memory)/PS (Preset Scan) |
eAUX indicator |
button |
rH-BASS (High BASS) indicator |
0%(release) button |
tMain display section |
!LO (local) button |
yAM/PM (clock) indicator |
@SEL (select) button |
uST (stereo) indicator |
#Preset station buttons (1 – 6) |
iSubdisplay section |
$AUX IN jack (3.5-mm dia.) |
od (tape direction) indicators |
%DISP (display) button |
pLO (local) indicator |
^INFO (My Information) button |
[Audio level indicator |
Rear panel
]Antenna jack
\REAR preout jacks
aPower supply/speaker connector sFuse
3 ENGLISH
CTX410(YU)-total-En-4
DETACHING AND ATTACHING THE FRONT PANEL
You can detach the front panel from the unit and carry it with you when you leave your car unattended.
When you carry the front panel out of your car, use the supplied carrying case.
Before detaching the front panel, remove the cassette to prevent possible damage to the unit.
1 Press and hold PWR for more than 2 seconds to turn the unit off.
2 While supporting the front panel with one hand, press % to release one side of the panel. Care must be taken not to drop the panel. It may suddenly become detached at this point.
3 When the front panel is lifted from the unit, remove it by pulling it away from the unit.
Do NOT touch the connector on the reverse side of the front panel, as doing so may contaminate the connector and cause poor connection, resulting in a malfunction.
Attaching the front panel
Security Lamp
When the front panel is detached, you can find an LED lamp on the front side of the unit. This lamp is designed to deter theft, and continues to flash when the front panel is detached. This unit is not equipped with any other security system, such as a security alarm, so there are limitations to its effectiveness.
LED lamp
ENGLISH 4
CTX410(YU)-total-En-5
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
SETTING THE CLOCK |
RADIO OPERATION |
|
|
|
|
|
|
|
||||||||
|
|
|
|
|
|
|
||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
1 Press PWR to turn the unit on.
2 Press DISP to have the clock displayed.
If the clock indication is already displayed, skip this step.
3 Press and hold DISP for more than 2 seconds.
4 Press TUNE i, then rotate the Jog Dial to set the hour.
Press TUNE k, then rotate the Jog Dial to set the minute.
Rotate the Jog Dial clockwise to go forward.
Rotate the Jog Dial counterclockwise to go backward.
5 Press DISP.
The clock starts working from 0 second.
To have the clock displayed when the unit is on
Press DISP. To return the unit to its former display, press DISP again.
5 ENGLISH
1 Press PWR to turn the unit on.
2 Press FUNC repeatedly to select the band from among FM1, FM2, FM3, AM1, and AM2.
The band indicators appear cyclically in order.
•FM1, FM2 and FM3 share the same frequency range.
•AM1 and AM2 share the same frequency range.
Band indicator |
Frequency indication |
3 Press (and hold for more than 2 seconds) either TUNE i or TUNE k to tune in the desired station.
The unit starts scanning and tunes in a station automatically (seek tuning).
Press TUNE i to increase and TUNE k to decrease the frequency.
Press the button again to cancel seek tuning.
Repeat the procedure until the desired station is tuned in.
Note
If you press (for less than 0.5 second at a time) either TUNEior TUNE k, the frequency increase or decrease step by step.
4 Adjust the volume with the Jog Dial.
CTX410(YU)-total-En-6
To turn the unit off
Press and hold PWR for more than 2 seconds. If you press this button for less than 2 seconds, it functions as MUTE.
Note
The unit turns on in the last mode selected when you turned off the unit.
LO (local/DX) button
You can use Local mode when you wish to tune in only strong stations during seek tuning. In
Radio mode, press LO to select Local mode. The “LO” indicator lights up.
•Press LO to cancel Local mode and switch to
DX (distance) mode.
•The “ST” (stereo) indicator lights up when the tuned-in station is broadcasting in stereo and the reception is good.
FUNC (function) button
Each time you press FUNC, the unit switches to one of the following modes, in cyclic order.
FM1
FM2
FM3
AM1
AM2 
*Tape Play mode (available while a cassette is in the unit)
PRESETTING STATIONS
To preset stations automatically
(Auto Memory)
1 Press PWR to turn the unit on.
2 Press FUNC repeatedly to select a desired band from among FM1, FM2, FM3, AM1, and AM2.
3 Press and hold A.ME/PS for more than
2 seconds to activate the automatic presetting function.
This unit can store up to 6 stations in memory for the preset station buttons 1 to 6 (with the
“LO” (local) indicator lit).
If the unit could not find strong stations, the “LO” (local) indicator goes off, and a search begins for weaker stations.
Use this function to automatically preset up to 6 stations each for FM1, FM2, FM3, AM1, and AM2
(up to a total of 30 stations).
•When the auto memory operation is completed, the station assigned to preset station button 1 is tuned in.
•To stop the auto memory operation, press A.ME/
PS again.
To check the preset stations (Preset Scan)
•If you wish to check the preset stations, press A.ME/PS for less than 2 seconds. The preset stations stored in memory will be tuned in for 5 seconds each in order.
•To stop this function, press A.ME/PS again or press any of the preset station buttons 1 to 6.
continued
ENGLISH 6
CTX410(YU)-total-En-7
PRESETTING STATIONS
To preset stations manually
You can manually preset stations that have not been selected by an auto memory operation.
1 Press PWR to turn the unit on.
2 Press FUNC repeatedly to select the band from among FM1, FM2, FM3, AM1, and AM2.
3 Tune in the station that you wish to preset with TUNE i or TUNE k.
4 Press and hold one of the preset station buttons 1 to 6 for approximately 2 seconds.
While the station you are presetting is being registered in memory, the unit beeps.
The preset station number appears to the right of the frequency indication.
Frequency |
Preset station |
||||
indication |
number |
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Repeat these procedures to preset up to 6 stations each for FM1, FM2, FM3, AM1, and AM2.
•If you preset a station on a preset station button on which another station of the same band has already been preset, the previously preset station will be erased.
7 ENGLISH
To tune in a preset station
1 Press PWR to turn the unit on.
2 Press FUNC repeatedly to select a desired band from among FM1, FM2, FM3, AM1, and AM2.
3 Press the desired preset station button.
The preset station number appears to the right of the frequency indication.
Active tuning reception control (ATRC)
This unit automatically suppresses FM noise caused by varying signal strength resulting from movement of the car.
•The built-in automatic blending circuit mixes the left and right channel signals according to the strength of the reception. At the same time, the high-cut circuit activates to maintain sound quality.
•If the reception becomes even weaker, the unit automatically switches to Monaural mode to reduce noise.
CTX410(YU)-total-En-8
MY INFORMATION
SWITCH
You can timer-activate the radio for a daily radio program. The unit turns on and off in Radio mode at the preset turn-on and turn-off times automatically.
Setting the timer
1
2
3
With the unit off, press and hold INFO for more than 2 seconds.
The “PO” indication flashes in the display window.
Press SEL.
The timer indication flashes.
Set the time you wish the unit to turn on in Radio mode.
Press TUNE i, then rotate the Jog Dial to set the hour.
Press TUNE k, then rotate the Jog Dial to set the minute.
MY INFORMATION SWITCH
Activating the timer
1 With the unit on, press INFO.
The “MY INFO” indicator lights up and the timer is activated.
The “MY INFO” indicator flashes between turn-on time and turn-off time.
To cancel the timer
Press INFO again so that the “MY INFO” indicator disappears.
To check the setting
With the unit off, press INFO.
The turn-on time, followed by the radio frequency and the turn-off time, appears in the display window, each for 1 second, then the unit turns off.
Notes
•Even if the unit is in a mode other than Radio mode, the unit switches to Radio mode and tunes in the preset radio program at the preset time automatically. When the program is over, the unit returns to the former mode automatically.
•When this function is activated, TUNE i/k, A.ME/PS, LO, and the preset number buttons do not work for tuning in stations.
•Even if the unit is turned off and on, or the front panel is detached and attached, this function is active until turn-off time.
•Even if you are listening to a radio program with this function, pressing FUNC switches the unit to another mode. If you switch modes with FUNC, the unit does not turn off at the turn-off time of the timer.
9 ENGLISH
TAPE PLAYBACK
1 Insert a cassette to start playback.
If a cassette is already inserted, press FUNC repeatedly to select Tape Play mode to start playback.
Playback starts in the direction that the unit played back previously.
2 Adjust the volume with the Jog Dial.
Press the following buttons to operate tape transport.
To do this |
Press this button |
Eject the cassette* |
|
|
|
Change the playback |
and |
side |
simultaneously |
|
|
|
|
Fast-forward the upper |
|
side (l) of the tape |
|
Rewind the lower side |
|
(j) of the tape |
|
Rewind the upper side (l) of the tape Fast-forward the lower side (j) of the tape
Stop fast transport and |
or |
lightly** |
resume playback |
|
|
*When you eject the cassette, the unit switches to the previous mode.
**Do not press 
or 
all the way. Doing so may change the direction of tape transport.
CTX410(YU)-total-En-10
Auto Reverse function
When the end of the tape is reached during playback or fast tape transport, the direction of the tape is automatically reversed, and playback starts on the other side.
Tape direction indications
Playback |
Fastforward |
|
or rewind |
Upper side
Lower side
Switching modes
When the unit is in a mode other than Tape Play mode, inserting a cassette switches the unit to
Tape Play mode automatically.
Before turning the ignition off
Be sure to eject any cassette.
To prevent tape problems
Before inserting a cassette into the unit, make sure that there is no slack in the tape. If necessary, take up the slack by inserting a pencil through the spindle hole and winding.
Tapes of 90 minutes or longer are extremely thin and easily deformed or damaged. They are not recommended.
SOUND ADJUSTMENTS
1 Press PWR to turn the unit on.
2 Press SEL repeatedly to select the mode that you wish to adjust from: BASS, TRE (treble), BAL (balance), FAD (fader) and VOL (volume).
Each time you press SEL, one of the following indicators appears, in cyclic order.
If you do not proceed with the following step
3 within 5 seconds, the selected mode is canceled, and the indication returns to the current source mode.
3 Rotate the Jog Dial to adjust the level.
Adjust each mode referring to the audio control indications in the display window.
Counterclockwise
Decreases the bass level
Decreases the treble level
Decreases the level of the right speaker(s)
Decreases the level of the front speakers
Decreases the volume level
Clockwise
Increases the bass level
Increases the treble level
Decreases the level of the left speaker(s)
Decreases the level of the rear speakers
Increases the volume level
Without selecting any mode with SEL, only the volume level can be adjusted by rotating the Jog Dial.
continued
ENGLISH 10
CTX410(YU)-total-En-11
SOUND ADJUSTMENTS
MUTE button
Press this button to temporarily lower the volume. Press it again to restore the previous volume. The “MUTE” indicator in the display window flashes while the mute function is active.
H-BASS (High BASS)
You can enjoy music with strong bass sound.
1 Press PWR to turn the unit on.
2 Press SEL repeatedly to select H-BASS (High BASS) mode.
3 Rotate Jog Dial to select on or off.
Select “On” to obtain powerful bass.
The “H-BASS” indicator lights up.
Select “OFF” to cancel H-BASS.
11 ENGLISH
Source Level Adjuster
You can adjust the output level in each mode to equalize the volume level.
1 Press PWR to turn the unit on.
2 Press FUNC repeatedly to select the desired mode.
3 Press DISP while pressing SEL.
The “LA 0” indication appears.
4 Rotate the Jog Dial to adjust the level.
Rotate clockwise to increase the output level. Rotate counterclockwise to decrease the output level.
If you do not operate the Jog Dial within 5 seconds, this function is canceled, and the indication returns to the current source mode.
CTX410(YU)-total-En-12
Returning to the factory settings
Adjusted settings of VOL, BASS, TRE, BAL, FAD, H-BASS, and source level can be returned to the factory settings with a simple operation.
1 With the unit off, press and hold DISP for more than 2 seconds.
The “LA--” indication appears, and all sound settings are returned to the factory settings.
CONNECTING A PORTABLE CD/MD/MP3 PLAYER OR OTHER EQUIPMENT
1 Press PWR to turn the unit on.
2 If a cassette is inserted, remove it to prevent possible damage to the unit.
3 Connect a portable CD/MD/MP3 player, etc. via the AUX IN jack (3.5-mm dia.) of the unit.
4 Press FUNC repeatedly to select AUX IN mode to output sound received from the connected equipment.
The “AUX” indicator lights up.
The clock display appears.
•For further information on the portable CD/MD/
MP3 player, etc., refer to the operating instructions for that equipment.
ENGLISH 12
CTX410(YU)-total-En-13
SETTING THE BEEP TONE
The unit is preset at the factory to beep each time you press any button on the front panel except %, z, f, or g(no beep with the Jog Dial). You can mute this beeping by following the procedure below.
1 With the unit off, press and hold SEL for more than 2 seconds.
The “BEEP” indication appears.
2 Rotate the Jog Dial to select on or off.
The beep function is activated when the “BEEP” indication appears with the audio level indicator lit, and canceled when not displayed.
Audio level indicator
3 Press and hold SEL for more than 2 seconds.
The unit turns off.
13 ENGLISH
MAINTENANCE
Cleaning the front panel
When the front panel is soiled, wipe the surface with a soft, dry cloth.
Cleaning the tape head
Use a cleaning cassette to clean the playback head and capstans approximately once a month.
If the head is dirty, the high tones may not be reproduced properly.
Cleaning the connector
The connector on the reverse side of the front panel needs to be cleaned occasionally. Wipe the surface of the connector with a cotton swab slightly moistened with alcohol.
CTX410(YU)-total-En-14
Loading...