Size:
394.14 Kb
Download

 

 

 

 

 

 

For more detailed documentation, visit us online at www.adtran.com

 

 

 

 

ATLAS 830

 

P/N 1200780L1 (AC)/1200781L1 (DC)

 

Quick Start Guide

 

 

 

 

 

 

 

 

Reviewing the Front Panel

Network Ports LEDs

Option Module LEDs

Controller LEDs

 

NE TW O RK

 

 

 

 

 

 

 

 

 

1

2

 

 

 

 

MODULES

 

 

ATLAS 830

PO WER

OK

OK

1

2

3

4

5

6

7

8

SYSTEM

TEST

TEST

STATUS

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ACO

 

 

 

 

 

 

 

 

 

 

CRAFT

 

 

ONLINE

 

 

 

 

 

 

 

ETHERNET

ERROR

ERROR

 

 

 

 

 

 

 

REMOTE

ALARM

ALARM

TEST

 

 

 

 

 

 

 

ACO Switch Craft Interface

Connecting to the ATLAS 830

Connecting a VT100 terminal (or VT100 terminal emulator) to the CRAFT interface (on the front panel of the unit) or the ADMIN interface (on the rear panel of the unit) allows access to the terminal menus and management features of the ATLAS 830.

Perform Steps Below in the Order Listed:

1.Configure a VT100 terminal (or terminal emulation software) with the following settings:

Data Rate:

9600 baud

Stop Bits:

1

Data Bits:

8

Flow Control:

None

Parity Bits:

None

 

 

If the terminal has a parallel setting, disable it and use serial.

2.Connect the DB-9 male end of the data cable into the ATLAS 830 CRAFT or ADMIN port. Make the connection to the VT100 terminal as appropriate for your connection.

3.Initiate a terminal session and the LOGIN screen displays. The default password is password. (Passwords in the ATLAS 830 are case sensitive.)

Craft Pinout

PIN

NAME

DESCRIPTION

1, 4, 6-9

N/A

Not Connected

2

RD

Receive Data (output)

3

TD

Transmit Data (input)

5

SG

Signal Ground

System Status LEDs

The System Status LEDs display the status of the power supply, controller, and other system parameters for the ATLAS 830. For a more detailed discussion of the front panel LEDs, refer to Section 2, Engineering Guidelines, of the ATLAS 830 System Manual.

LED

Description

Power

Indicates the status of the power supply

System

Indicates the status of the unit controller and other system parameters.

Ethernet

Indicates the status of the ethernet port.

Remote

Indicates whether a user (Telnet or VT100) is logged in to the unit.

Quick Start Guide, 61200780L1-13A, August 2002

Technical Support 1-888-4ADTRAN (1-888-423-8726)

Copyright 2002 ADTRAN, All Rights Reserved

For more detailed documentation, visit us online at www.adtran.com

 

 

 

 

ATLAS 830

 

 

 

 

 

 

 

 

 

P/N 1200780L1 (AC)/1200781L1 (DC)

 

Quick Start Guide

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Reviewing the Rear Panel Design

T1/PRI Monitor Jacks

Network T1/PRI Ports

Optional DC

 

 

Alarm Relay Connection

 

 

 

 

 

Power Supply

 

 

 

 

 

 

 

 

 

 

 

 

 

P/N 1200229L1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CAUTION: FOR CONTINUED PROTECTION

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

AGAINST RISK OF FIRE, REPLACE

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ONLY WITH SAMETYPE AND RATING

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

OF FUSE.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Admin Interface

 

 

 

 

 

 

 

 

Option Module Slots

Power Supply Slot

 

 

ON

OFF

12A/125V

-

+

48 VDC, 6A

USE COPPER

CONDUCTORS ONLY

SEE MANUAL BEFORE

REMOVING POWER SUPPLY

Admin Pinout

PIN

NAME

DESCRIPTION

1

DCD

Data Carrier Detect (output)

2

RD

Receive Data (output)

3

TD

Transmit Data (input)

4

DTR

Data Terminal Ready (input)

5

SG

Signal Ground

6

DSR

Data Set Ready (output) -- not connected

7

RTS

Request to Send (input)

8

CTS

Clear to Send (output)

9

RI

Ring Indicate (output) -- not connected

10/100BaseT Ethernet Pinout

PIN

NAME

DESCRIPTION

1

TX1

Transmit Positive

2

TX2

Transmit Negative

3

RX1

Receive Positive

4,5

Unused

6

RX2

Receive Negative

7, 8

Unused

Alarm Relay Connection Pinout

PIN

NAME

DESCRIPTION

1

Normaly Closed (NC)

Opens when a selected alarm condition is present.

2

Normally Open (NO)

Closes when a selected alarm condition is present.

3

Common (COM)

Common connection between external circuitry

 

 

and NC or NO terminal.

 

 

 

4

Chassis Ground (GND)

 

DC Power Supply Connection

(Optional P/N 1200229L1)

PIN

NAME

DESCRIPTION

1

+

Ground (GND)

2

-

-48VDC

Quick Start Guide, 61200780L1-13A, August 2002

Technical Support 1-888-4ADTRAN (1-888-423-8726)

Copyright 2002 ADTRAN, All Rights Reserved