Addonics Technologies JUPITER CIPHER EXDRIVE JCEDIF64, JUPITER CIPHER EXDRIVE JCEDIF128, JUPITER CIPHER EXDRIVE JCEDIS128, JUPITER CIPHER EXDRIVE JCEDIF192, JUPITER CIPHER EXDRIVE JCEDIU64, JUPITER CIPHER EXDRIVE JCEDIU128, JUPITER CIPHER EXDRIVE JCEDIS192, JUPITER CIPHER EXDRIVE JCEDIS64, JUPITER CIPHER EXDRIVE JCEDIU192 User Manual

5.08 Mb
Loading...

Addonics

T E C H N O L O G I E S

Jupiter Cipher ExDrive

For the following models: JCEDIU64, JCEDIF64, JCEDIS64

JCEDIU128, JCEDIF128, JCEDIS128 JCEDIU192, JCEDIF192, JCEDIS192

User’s Guide

Version 1.0

FCC Warning Statement

This equipment has been tested and found to comply with the limits for a class B digital device pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If the equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment on and off, the user is encouraged to try and correct the interference by one or more of the following suggestions.

Reorient or relocate the receiving antenna

Increase the distance between the equipment and the receiver

Connect the equipment to a different power outlet other than the one where receiver is connected

Consult a certified television or radio technician

LIMITED WARRANTY

Addonics guarantees that every product is free from physical defects in material and workmanship during the warranty period specified for each product when used within the limits set forth in the Specifications section in the user guide. Unauthorized tampering of the product or using it outside the scope of the product specifications will result in voiding the warranty. If the product proves defective during this warranty period, call Addonics Technical Support to obtain a Return Authorization number. BE SURE TO HAVE YOUR PROOF OF PURCHASE ON HAND WHEN CALLING. RETURN REQUESTS CANNOT BE PROCESSED WITHOUT PROOF OF PURCHASE. When returning a product, mark the Return Authorization number clearly on the outside of the package and include your original proof of purchase. Customers are responsible for paying the shipping and handling of the products to Addonics warranty service location.

IN NO EVENT SHALL ADDONICS’ LIABILITY EXCEED THE PRICE PAID FOR THE PRODUCT FROM DIRECT, INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THE PRODUCT, ITS ACCOMPANYING SOFTWARE, OR ITS DOCUMENTATION. Addonics makes no warranty or representation, expressed, implied, or statuary, with respect to its products or the contents or use of the user guide and all accompanying software, and specifically disclaims its quality, performance, merchantability, or fitness for any particular purpose. Addonics reserves the right to revise or update its products, software, or documentation without obligation to notify any individual or entity.

Addonics Technologies – Jupiter Cipher ExDrive User’s Guide v1.0

1

Contents

FCC Warning ...................................................................................

1

Limited Warranty ............................................................................

1

Contents............................................................................................

2

Chapter 1 General Information .........................................................

3

Features............................................................................

3

Jupiter Cipher Models ......................................................

4

Chapter 2 Jupiter Cipher ExDrive key...............................................

5

Chapter 3 Keeping track of the hard drive.........................................

6

Chapter 4 Jumper Setting for Jupiter Cipher ExDrive .......................

7

Chapter 5 Hardware Installation Guide ........................................

8-10

Chapter 6 Attaching USIB Interface Cable .....................................

11

Chapter 7 USB2.0 USIB Interface Cable Driver Installation ......

12-13

Serial ATA USIB Interface Cable Driver Installation

.... 14

Firewire USIB Interface Cable Driver Installation .........

15

How to use Disk Management ...................................

16-17

Technical Support & Contact Information................................

…18

Addonics Technologies – Jupiter Cipher ExDrive User’s Guide v1.0

2

Chapter 1

General Information

The Addonics Technologies Jupiter Cipher ExDrive is a portable 2.5” Hard Disk Drive kit. The unit is external and uses the USB2.0, Firewire/iLink, and Serial ATA interfaces.

Features

Stylished and rugged black anodized aluminum housing

Compact size and light weight

Shock proof - up to 3 feet drop damage protection for the hard drive

Easy hard drive installation

Choice of standard or encryption drive enclosure

The most versatile hard drive kit in the market

Connect as an External Hard drive to any computer via USB2.0, CardBus, Firewire/iLink and Serial ATA port (only one of these cables is included in

Turn any 2.5” hard drives into external hard drive or removable hard drive

Use as a removable Hard Drive on Desktops PC with an optional IDE drive cradle.

Plug & Play Operation under Windows 98SE, Me, 2000, XP and 2003 Server

Portable: Fits any Briefcase or Notebook PC Case.

Encryption

Hardware based 64-bit DES and 128-bit or 192-bit TDES full disk encryption

High performance - Data is encrypted and decrypted on the fly by a certified cryptographic engine inside an ASIC without taking any CPU resources

Encryption / Decryption via a hardware key, just like using a regular key to open a door.

Simple to deploy with no training required, no software to install and no password to remember

Platform independency - There is no software or driver to install to use Addonics encryption products. As a result, it can be deployed in any systems running any OS. This is important in organization with multi platform computing and legacy systems.

Addonics Technologies – Jupiter Cipher ExDrive User’s Guide v1.0

3

Jupiter Cipher ExDrive

Item Number

Product Description

JCEDIU64

Jupiter Cipher ExDrive 64-bit for 2.5” IDE hdd, USB 2.0

JCEDIF64

Jupiter Cipher ExDrive 64-bit for 2.5” IDE hdd,

 

Firewire/iLink

JCEDIS64

Jupiter Cipher ExDrive 64-bit for 2.5” IDE hdd, SATA

JCEDIU128

Jupiter Cipher ExDrive 128-bit for 2.5” IDE hdd, USB 2.0

JCEDIF128

Jupiter Cipher ExDrive 128-bit for 2.5” IDE hdd,

 

Firewire/iLink

JCEDIS128

Jupiter Cipher ExDrive 128-bit for 2.5” IDE hdd, SATA

JCEDIU192

Jupiter Cipher ExDrive 192-bit for 2.5” IDE hdd, USB 2.0

JCEDIF192

Jupiter Cipher ExDrive 192-bit for 2.5” IDE hdd,

 

Firewire/iLink

JCEDIS192

Jupiter Cipher ExDrive 192-bit for 2.5” IDE hdd, SATA

Addonics Technologies – Jupiter Cipher ExDrive User’s Guide v1.0

4

Chapter 2 Jupiter Cipher ExDrive key

Check to make sure you have the correct version of Jupiter Cipher ExDrive key. The key should match the label at the bottom of the drive enclosure.

Yellow label DES-64 stands for Jupiter Cipher ExDrive 64-bit key

Green label TDES-128 stands for Jupiter Cipher ExDrive 128bit key

Red label TDES-192 stands for Jupiter Cipher ExDrive 192bit key

IMPORTANT

There is no back door for the Jupiter Cipher ExDrive encrypted hard drive if the key is lost or stolen.

To ensure that there is a spare key, your Jupiter Cipher ExDrive bundled kit comes with one pair of Jupiter Cipher ExDrive keys. These 2 keys have identical encryption code. One of these keys should be kept in a safe and secure location and can be sent back to Addonics for duplicating additional keys. If you are down to the last key, be sure to make a back up of all the data stored inside your encrypted hard drive prior to sending the last key to Addonics. Addonics is not responsible for key lost in the mail or retrieval of the data inside the encrypted hard drive.

ØThe CIPHER key MUST be inserted at the front of the drive enclosure in order for the drive to be ACTIVATED.

ØOnce the drive is INITIALIZED using the Cipher Key that comes with the kit, the drive can only be accessed by the original key.

ØThe 2 keys that come with each Jupiter Cipher ExDrive bundled kit has their own unique encryption code. So the keys among different kits are not interchangeable.

If you have multiple sets of Jupiter Cipher ExDrive kits and would like all the keys to have the same encryption code, you may make this request at the time of your order or mail the keys together with master key back to Addonics to recode them for you. Again be sure that you keep a spare key with you. Make a back up of your data if you are mailing in your last key.

Addonics Technologies – Jupiter Cipher ExDrive User’s Guide v1.0

5

Chapter 3 Keeping track of the hard drive

If you are using the Jupiter Cipher ExDrive drive enclosure to encrypt multiple hard drives, it is important to label your hard drive if you are taking the drive out of the enclosure. The hard drive with Jupiter Cipher ExDrive encryption will look like a brand new drive when attach directly to the IDE or SATA controller of a computer. There will be no partition or any hint to indicate that the drive contains encrypted data. When the drive is partitioned, all the encrypted data will be lost.

The same holds true if a hard drive already has data on it is installed into the Jupiter Cipher ExDrive drive enclosure. The computer detects the hard drive as a brand new drive or a drive that is unallocated. Once you proceed to partition the drive, the data that was on the hard drive will be erased and cannot be recovered.

A Jupiter Cipher ExDrive encrypted hard drive can be moved to another Jupiter Cipher ExDrive drive enclosure. But the same key used in encrypting the hard drive must be used in the new drive enclosure in order to access the drive.

If you are installing multiple Jupiter Cipher ExDrive drive kits into a large organization, it is important to keep track of the drive and the encryption key. Once it gets mixed up, there is no possible way to recover the data on the encrypted hard drive.

Addonics Technologies – Jupiter Cipher ExDrive User’s Guide v1.0

6

Chapter 4

Jumper settings inside the Jupiter Cipher ExDrive Drive Case

A.If the Jupiter Cipher ExDrive will be used externally with the external AC adapter, the switch from the case must be switch to the right, labeled EXT to grab power from external power supply.

Application: Jupiter Cipher ExDrive can be set to receive power EXT and be used with all three types of USIB cables.

B.If the Jupiter Cipher ExDrive will be used externally without the external AC adapter, the switch from the case must be switch to the left, labeled INT to grab power from system.

Application: Jupiter Cipher ExDrive can be set to receive power INT and be used with the following types of USIB cables: USB2.0 USIB & Firewire USIB

Note: We recommend setting the hard drive to MASTER mode/setting at all times. (Default setting)

J4 Pin Definition for Master Setting

Hard Drive Brand

Master Setting

Hitachi

Pin 1~6 Open

NEC

 

Fujitsu

 

Toshiba

 

Seagate

Pin 3 - Pin 4 Short

J1 Pin Definition for USIB Interface

 

 

Hard Drive Setting

J1 Jumper Setting

Master

Pin 3 - Pin 5 Short

 

 

Addonics Technologies – Jupiter Cipher ExDrive User’s Guide v1.0

7

Chapter 5

Hardware Installation Guide

Exploded View of Enclosure shown with various components

top cover

hard drive

shock absorbers

switch

PCB

bottom cover

screw

cipher slot

Step 1

Separate the top from the bottom cover of the drive enclosure by loosening the screw as shown on the photo.

Addonics Technologies – Jupiter Cipher ExDrive User’s Guide v1.0

8

Step 2

Align the male IDE connector on the 2.5” hard drive with the female IDE connector on the PCB. Push the hard drive till the connector pins on the hard drive is fully seated inside the connector on the PCB.

Step 3

Wrap the shock absorber around the hard drive and PCB.

Step 4

Turn over the PCB and secure the hard drive to the PCB with the mounting screws that come with the kit.

Step 5

Mount the board to the bottom cover.

Addonics Technologies – Jupiter Cipher ExDrive User’s Guide v1.0

9

Step 6

Put the top cover on by holding it in near vertical position and sliding the two metal clips inside the two small slots on the rear of the bottom cover.

Step 7

Lower the front of the top cover and making sure the two covers lined up properly. Tighten the small retaining screw on the front of the bottom cover to close the enclosure.

Addonics Technologies – Jupiter Cipher ExDrive User’s Guide v1.0

10

Chapter 6 Attaching USIB interface cable

USIB connector for use with the Addonics USIB interface cable

External power input jack (for use as external hard drive)

Addonics USIB interface cable

Be sure the Jupiter Cipher ExDrive key is inserted into the drive enclosure prior to turning on the power or attaching the USIB interface cable to the computer. Hard drive will not be detected if the interface cable is attached to the computer without the Cipher key inserted first. Under such condition, the power to the drive enclosure will have to be turned off and turned back on with the Cipher key already inserted into the drive enclosure in order for the hard drive to be detected by the system.

The Jupiter Cipher ExDrive drive enclosure can be used as an internal removable hard drive or as a drive cartridge by installing the optional drive cradle into the drive bay of a Desktop, Server or any computing equipment.

Addonics Technologies – Jupiter Cipher ExDrive User’s Guide v1.0

11

Chapter 7

7.1USB2.0 USIB Cable (Model: AAUSBC-309)

Note: USB Jupiter Cipher ExDrive is Plug and Play under Windows XP, 2000 and 98Me. There is no third party driver needed.

Since USB 2.0 Hi-Speed is an evolution of the existing USB 1.1 specification, it is fully forward and backward compatible with current USB systems.

If you do not have an USB2.0 port, you may install an optional USB2.0 adapter or controller

Driver Installation for Win98 and Win98SE

Downloading the USB2.0 USIB Cable Driver from the Addonics Driver Disk

1.Insert the Addonics Driver Disk in the CDROM drive. The Addonics Driver Disk window opens.

2.Select Drivers > Interface Cables Drivers > USB2.0 Cable (AAUSBC-309) Win98/98SE Only.

3.The Winzip Self-Extractor –AT2LP.exe window opens. Unzip file in My Documents.

Addonics Technologies – Jupiter Cipher ExDrive User’s Guide v1.0

12

Driver Installation for Win98 and Win98SE

1.Make sure your computer is up and running.

2.Insert the USB2.0 USIB cable to the USB Port.

3.A "New Hardware Found" message shall pop up, click Next.

4.“What do you want Windows to do?” message opens. Select “Search for the best driver for your device,” click Next.

5.“Specify Location” message opens. Point to the location of C:\My Documents\mass_storage_601where you unzip the files for the driver. Click Next.

6.“Driver file search for the device %VID_ODBF&PID_0303%” then Building a driver database message opens. Let Windows finish the installation and click Finish.

Disk Management for Windows 98

1.Select Start > Setting > Control Panel > System. The System Properties window opens.

2.Select the Device Manager tab, under Device type, Disk Drives, select your new hard drive. Click the Properties button.

3.Select the Settings tab and under the Options box, click the Removable check box. The Reserved drive letters box becomes active. Select the drive letter for your new drive. Click Ok.

4.Click Yes to restart your system to make changes take effect.

5.Double click My Computer icon and there should be an extra drive letter for the Jupiter Cipher ExDrive drive. You may now access the drive.

Addonics Technologies – Jupiter Cipher ExDrive User’s Guide v1.0

13

7.2SATA USIB Cable (Model: AASAC-605)

For Win98SE, Me, 2000 and XP

Note: There are no drivers needed to use the Serial ATA cable as long as the drivers are installed for the Serial ATA Controller card/chip. It is plug and play.

Disk Management for Windows 98

Note: Refer to the SATARAID Management Utility Manual

SATARAID Manual V1.30 (for non-RAID5 Controllers) found in the Addonics Technologies website

Addonics Technologies – Jupiter Cipher ExDrive User’s Guide v1.0

14

7.3FIREWIRE USIB Cable (Model: AAFWC-406)

Note: Firewire Jupiter Cipher ExDrive is Plug and Play under Windows XP, 2000 and 98Me. There is no third party driver needed.

Driver Installation for Win98 and Win98SE

After plugging in the cable some system might prompt you for Win98SE CD, in case you don’t have the Win98SE CD and the wizard prompts you for:

NTMAP.SYS please type C:\WINDOWS\SYSTEM32\DRIVERS NTMAPHLP.PDR please type C:\WINDOWS\SYSTEM\IOSUBSYS

Reboot your system.

Disk Management for Window 98

1.Select Start > Setting > Control Panel > System. The System Properties window opens.

2.Select the Device Manager tab, under Device type, Disk Drives, select QTS FIREWIRE CABLE. Click the Properties button.

3.Select the Settings tab and under the Options box, click the Removable check box. The Reserved drive letters box becomes active. Select the drive letter for your new drive. Click Ok.

4.Click Yes to restart your system to make changes take effect.

5.Double click My Computer icon and there should be an extra drive letter for the Jupiter Cipher ExDrive drive. You may now access the drive.

Addonics Technologies – Jupiter Cipher ExDrive User’s Guide v1.0

15

For Windows 2000 & XP Operating Systems

How to use Disk Management

To start Disk Management:

1.Log on as administrator or as a member of the Administrators group.

2.Click Start, click Run, type compmgmt.msc, and then click OK. In the console tree, click Disk Management. The Disk Management window appears. Your disks and volumes appear in a graphical view and list view.

3.To customize how you view your disks and volumes in the upper and lower panes of the window, point to Top or Bottom on the View menu, and then click the view that you want to use

How to create a new partition or a new logical drive

To create a new partition or logical drive on a basic disk:

1.In the Disk Management window, complete one of the following procedures, and then continue to step 2:

To create a new partition, right-click unallocated space on the basic disk where you want to create the partition, and then click New Partition.

To create a new logical drive in an extended partition, right-click free space on an extended partition where you want to create the logical drive, and then click New Logical Drive.

2.In the New Partition Wizard, click Next.

3.Click the type of partition that you want to create (either Primary partition, Extended partition, or Logical drive), and then click Next.

4.Specify the size of the partition in the Partition size in MB box, and then click Next.

5.Decide whether to manually assign a drive letter, let the system automatically enumerate the drive, or do not assign a drive letter to the new partition or logical drive, and then click Next.

6.Specify the formatting options you want to use by using one of the following procedures:

If you do not want to format the partition, click Do not format this partition, and then click Next.

If you want to format the partition, click Format this partition with the following settings, and then complete the following procedure in the Format dialog box:

a.Type a name for the volume in the Volume label box. This is an optional step. Click the file system that you want to use in the File system box.

b.You can change the disk allocation unit size, and then specify whether to perform a quick format, or enable file and folder compression on NTFS volumes.

Click Next.

Addonics Technologies – Jupiter Cipher ExDrive User’s Guide v1.0

16

7.Confirm that the options that selected are correct, and then click Finish.

The new partition or logical drive is created and appears in the appropriate basic disk in the Disk Management window. If you chose to format the volume in step 6, the format process now starts.

How to format a basic volume

To format a partition, logical drive or basic volume:

1.In the Disk Management window, right-click the partition or logical drive that you want to format (or reformat), and then click Format.

2.In the Format dialog box, type a name for the volume in the Volume label box. This is an optional step.

3.Click the file system that you want to use in the File system box. If you want, you can also change the disk allocation unit size, specify whether you want to perform a quick format, or enable file and folder compression on NTFS volumes.

4.Click OK.

5.Click OK when you are prompted to format the volume. The format process starts.

Addonics Technologies – Jupiter Cipher ExDrive User’s Guide v1.0

17

Technical Support

If you need assistance to get your unit functioning properly, please call Addonics Technical Support. Our technical staff will be happy to assist you, but they will need your help to do so. Calling the technical support staff without all the proper information can be both time consuming and frustrating. Here are some tips to help you out:

(1)MODEL NUMBER – Please have this number on hand.

(2)SYSTEM INFORMATION – Type of computer, peripherals, etc.

(3)OPERATING SYSTEM – What version of Windows

(4)WHAT’S THE TROUBLE? – Give enough information About your problem so that we can recreate and diagnose it.

FREE Software Drivers for all Addonics Technologies

Products are available 24 hours per day at the

World Wide Web Site: www.addonics.com.

Contact Information

Addonics Technologies

2466 Kruse Drive

San Jose CA, 95131

Phone: 408-433-3899

Fax: 408-433-3898

Email: sales-team@addonics.com

Internet: http://www.addonics.com

TECHNICAL SUPPORT

Phone: 408-433-3855

Hours: 9:00-6:00 PST

Email: techinfo@addonics.com

Addonics Technologies – Jupiter Cipher ExDrive User’s Guide v1.0

18