Adams Rite EX76-L313, EX76-L313M, EX76-L335, EX76-L335M, EX76-L628 Installation Instructions

...
0 (0)
EX76 Concealed Vertical Rod Exit Device
Box Contents
EX76 Concealed Vertical Rod Exit Device
Door Kit with Templates
Rod Assembly
Frame Kit with Installation Instructions
Mounting End Cap Kit
Recommended Installation Tools
Safety glasses Measuring tape Level Pencil Power drill Center punch Phillips screw driver Saw horse
Filler Plate
Back Bar
Active Push Bar
Preparation Guide and Installation Instructions
IMPORTANT NOTE 1: All work must be performed to applicable building, regulatory and life­safety codes. Please consult local Authority Having Jurisdiction (AHJ) for more information.
IMPORTANT NOTE 2: The Americans with Disabilities Act (ADA) guidelines specify door hardware be installed 34”minimum and 48” maximum above the finished floor.
Page | 1 P 800.872.3267 F 800.232.7329 E techsupport.adamsrite@assaabloy.com www.adamsrite.com
Sizing the Exit Device
Standard Door Widths and Mounting Hole Spacing
Exit Device Length
Regular (R)
Midlength (M)
Long (L)
Standard Door
Width
No Cut Required
36”
42”
48”
Minimum Door
Width Exit Device
Can Support
30”
30”
42”
NOTE: All EX Series Exit Devices are sized at the factory for 5/8” frame stop in narrow stile aluminum
applications.
1. DETERMINE cut off dimension “B” Back Bar extrusion length by subtracting 3-7/8” from door
opening width.
2. MARK cut off line “B” on Filler Plate and Back Bar.
3. REMOVE Filler Plate from Back Bar and CUT along lines on both pieces. REPLACE Filler Plate into
Back Bar.
IMPORTANT NOTE: Do not cut Active Push Bar
“B”
Page | 2 P 800.872.3267 F 800.232.7329 E techsupport.adamsrite@assaabloy.com www.adamsrite.com
Measuring the Backset
NOTE: Backset is always measured at the door centerline, and not edge.
Preparing the Inside of the Door
1. DETERMINE and MARK the applicable bar height centerline (horizontal line) of the exit device on the
interior of the door.
2. DETERMINE and MARK the backset required.
3. DETERMINE the location of the door templates by using the bar height centerline of the exit device
and aligning the template with the backset centerline (vertical line) of the door. AFFIX the templates to the door.
4. DETERMINE and MARK the hinge side preparation using dimension “A” as shown in the “Standard
Door Widths and Mounting Hole Spacing” chart below.
5. IF standard door widths, as shown in the Standard Door Widths and Mounting Hole Spacing” chart
below are not being used, THEN CUT to proper length using Sizing the Exit Device section on page 2.
6. MARK, CENTER PUNCH, DRILL all holes.
7. PREPARE door for cylinder escutcheon using Preparing the Door for Mortise Cylinder Escutcheon on
page 6, if required.
8. REMOVE the templates.
Standard Door Widths and Mounting Hole Spacing
Exit Device Length
Regular (R)
Midlength (M)
Long (L)
Standard Door
Opening Width
36”
42”
48”
Dimension “A”
33-¼”
39-¼”
45-¼”
Radius
Cylinder
Bevel
Flat
NOTE:
The backset required by this CVR exit device is 1-3/32”
Page | 3 P 800.872.3267 F 800.232.7329 E techsupport.adamsrite@assaabloy.com www.adamsrite.com
LHR Shown
Bar Height Centerline
“A”
Drill 5/32”dia pilot
holes for self-tapping screws, 2 places
11/16”
9/16” 9/32”
1-3/32” backset
17/32”
1”
1”
Lead Edge
13/64" dia thru c'sink 25/64" dia x 82 deg, 2 places
1-3/8”
1/8” x 45
deg chamfer, 2 places
0.45”
3/16”
dia thru, 4 places
5/8” dia
thru
13/64” dia thru c’sink 25/64”
dia x 82 deg, 2 places
Lead Edge
1-5/8”
Backset
7/8”
NOTE:
The backset required by this CVR exit device is 1-3/32”
3/8”
Page | 4 P 800.872.3267 F 800.232.7329 E techsupport.adamsrite@assaabloy.com www.adamsrite.com
RHR Shown
9/16” 9/32”
1-3/32” backset
17/32”
1”
1”
1/8” x 45 deg
chamfer, 2 places
13/64" dia thru c'sink 25/64" dia x 82 deg, 2 places
Lead Edge
0.45”
5/8” dia
thru
3/16”
dia thru, 4 places
1-5/8”
Lead Edge
7/8”
3/8”
Backset
13/64” dia thru c’sink 25/64” dia
x 82 deg, 2 places
NOTE:
The backset required by this CVR exit device is 1-3/32”
Bar Height Centerline
“A”
Drill 5/32”dia pilot
holes for self-tapping screws, 2 places
11/16” 1-3/8”
Page | 5 P 800.872.3267 F 800.232.7329 E techsupport.adamsrite@assaabloy.com www.adamsrite.com
Loading...
+ 11 hidden pages