Acer ASPIRE 1650Z, ASPIRE 1690-DDR2, EXTENSA-6700, ASPIRE 3020, ASPIRE 4310 User Manual

...
0 (0)

Modem

User’s Guide Manuel d’utilisation Benutzerhandbuch Mauale dell’utente Guía del usuario

Part No.: HMU.0550.003

Doc No.: NB235-0110A

Copyright © 2001 Acer Incorporated.

All Rights Reserved.

Modem User’s Guide

Original Issue: September 2001

Changes may be made periodically to the information in this publication without obligation to notify any person of such revision or changes. Such changes will be incorporated in new editions of this manual or supplementary documents and publications. This company makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims the implied warranties of merchantability or fitness for a particular purpose.

Record the model number, serial number, purchase date, and place of purchase information in the space provided below. The serial number and model number are recorded on the label affixed to your computer. All correspondence concerning your unit should include the serial number, model number, and purchase information.

No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopy, recording, or otherwise, without the prior written permission of Acer Incorporated.

Model number : _________________________________

Serial number: ___________________________________

Purchase date: ___________________________________

Place of purchase: ________________________________

Acer and the Acer logo are registered trademarks of Acer Incorporated. Other brands and product names are trademarks and/or registered trademarks of their respective owners.

1

Modem user’s guide

Introduction

This V.90 modem provides the highest speed access to the Internet and online services, and especially accelerates downloading of graphics, telegaming, and collaborative computing. It’s the highest speed international FAX/modem available. It has worldwide homologation support which allows you to instantly configure the modem for telephone lines, so you don’t have to pay additional, up-front, monthly costs for special lines.

Features

Highest Internet connection rates, downstream speeds to 56kbps, backward compatible with V.34 modems

Data mode capabilities:

ITU-T V.90 data rates: 28000bps ~ 56000bps

Ultrahigh compression throughput due to parallel access directly to the host PC

ITU-T V.34 extended rates: 33600bps ~ 24000bps

V.32terbo, V.32bis

TIA/EIA 602 standard for AT command set

V.42 error correction (LAPM and MNP)

V42bis and MNP Class 5 data compression

Fax mode capabilities:

ITU-T V.17, V.29, V.27ter, and V.21 Channel 2 standards

TIA/EIA 578 Class 1 FAX

Auto-dial, call progress monitor

Ring, line break detection

Low Power consumption

ITU standard V.92 software upgradeability

Worldwide homologation support

Software support

2

Note: Execute this program to match the country you are currently in for the modem to function properly.

Installing and Testing the Modem

Installing and Configuring the Software

Install the communications software according to the software user’s modem of the same COM port and IRQ line used by the modem. You may be prompted by the software to configure certain communication

parameters. We suggest the following settings:

Item

Suggested Setting

 

 

Baud rate

115200 bps

 

 

Data bits

8

 

 

Parity

none

 

 

Stop bit

1

 

 

Flow control

Xon./Xoff

 

 

initialization string

AT&F

 

 

Testing Your Modem

In order to check if the modem is installed properly, make sure that the COM Port and IRQ settings of the modem match the software. Type AT on your terminal screen and press ENTER. The modem should respond by displaying an OK (or 0). If it does not, either the modem may not have been installed properly or the software has not been properly configured.

Using Your Modem

The communications software included with your modem provides a user friendly interface to access the data and fax. The modem may also perform basic communication functions (such as dialing) via the AT commands. Please refer to “AT Commands” on page 4 for detailed

Acer ASPIRE 1650Z, ASPIRE 1690-DDR2, EXTENSA-6700, ASPIRE 3020, ASPIRE 4310 User Manual

3

descriptions. Since the communication software is designed to shield the user from the difficult and cumbersome AT commands, we strongly suggest that all modem operations be performed via the software.

Troubleshooting

If you encounter problems while using your modem, please read this chapter. If you cannot resolve your difficulties after reading this

chapter, contact your dealer or vendor for assistance.

Problem Solution

Modem does not respond to commands

1Make sure the communications software is configured with the correct COM port and IRQ setting (same COM port and IRQ setting as the modem). Your communications software will not be able to send or receive any data if it is not configured to match the COM and IRQ settings for the modem.

2Make sure that your modem is initialized correctly. Your modem may have been improperly initialized by the software because you have selected an incorrect modem type. You may also be prompted to enter an initialization string by the software. Use AT&F as your initialization string.

Modem dials but

1

Make sure the IRQ setting is identical on both the

does not connect.

 

modem and the software.

 

2

Make sure the phone line is working properly. A

 

 

noisy line will prevent proper modem operation.

Modem makes a connection but no data appears on your screen.

1Make sure all communication parameters (baud rate, data, stop, and parity bits) are properly configured and are identical on both sides. Be certain software flow control (Xon-Xoff - default) is enabled in both the modem and the communication software.

2Press the ENTER key several times. The remote system may be waiting to receive your data before it begins.

4

Problem

Solution

 

 

 

Modem

1

Make sure Call Waiting is turned off.

experiences errors

2

Make sure to use Xon/Xoff software flow control

while on-line with

 

when transferring binary files.

a remote modem.

 

 

 

 

 

 

AT Commands

Basic AT Commands

A summary of the commands implemented by the modem are shown in the following table labeled “AT Command Set Summary”. Commands may be executed when the modem is in COMMAND mode. COMMAND mode is entered upon one of the following conditions:

After power up

At the termination of a connection

After the execution of a command other than dial or answer commands (ATO or AT&T)

Upon the receipt of the ESCAPE SEQUENCE (three consecutive characters matching the contents of S register 2) while in online mode

Upon the on-to-off transition of DTR if D1, &D2, or &D3 has been set

5

AT Commands Set Summary

Command

Description

Command

Description

 

 

 

 

A/

Re-execute command

&Dn

Data terminal ready

 

 

 

(DTR) option

 

 

 

 

AT=X

Write to Selected

&Fn

Restore default

 

S-register

 

configuration

 

 

 

 

AT?

Read selected

&Gn

Select guard tone

 

S-register

 

 

 

 

 

 

A

Answer

&Kn

Flow control

 

 

 

 

Bn

CCITT/Bell mode

&Mn

Mode selection

 

 

 

 

Cn

Carrier control

 

 

 

 

 

 

Dn

Dial

&Pn

Pulse dialing control

 

 

 

 

En

Command echo

&Qn

Mode selection

 

 

 

 

Hn

Disconnect and hook

&Tn

Test and diagnostics

 

control

 

 

 

 

 

 

In

Modem identification

&Sn

Data set ready (DSR)

 

 

 

option

 

 

 

 

Ln

Speaker volume

&V

Display current

 

 

 

configuration

 

 

 

 

Mn

Speaker control

&Wn

Store current

 

 

 

configuration

 

 

 

 

On

Return to on-line data

&Yn

Select default reset

 

mode

 

profile

 

 

 

 

P

Set pulse dialing as

&Zn=x

Store telephone

 

the default

 

number

 

 

 

 

Qn

Result code control

%En

Auto fallback/

 

 

 

fallforward control

 

 

 

 

Sn

Access S-register

\An

Select maximum MNP

 

 

 

block size

 

 

 

 

6

Command

Description

Command

Description

 

 

 

 

T

Set tone dial as the

\Bn

Transmit break to

 

default

 

remote

 

 

 

 

Vn

Result code form

\Jn

DCE rate adjustment

 

 

 

 

Wn

Connect result code

\Kn

Break control

 

control

 

 

 

 

 

 

Xn

Extended result code

&Cn

Data carrier detect

 

control

 

(DCD) control

 

 

 

 

Yn

Long-space disconnect

Zn

Reset

 

 

 

 

7

FAX Command Table

Command

Function

Command

Function

 

 

 

 

 

+FCLASS=n

Set service class

+FTH=98

V.17

9600 bps (short

 

 

 

 

train)

 

 

 

 

+FCLASS=0

Select data mode

+FTH=121

V.17 12000 bps (long

 

(Default)

 

train)

 

 

 

 

 

+FCLASS=1

Select FAX Class 1

+FTH=122

V.17

12000 bps

 

 

 

 

(short train)

 

 

 

 

+FTS=n

Stop transmission and

+FTH=145

V.17 14400 bps (long

 

wait

 

 

train)

 

 

 

 

 

+FRS=n

Receive silence

+FTH=146

V.17

14400 bps

 

 

 

 

(short train)

 

 

 

 

+FTH=n

Transmit data with

+FRH=n

Receive data with

 

HDLC framing

 

HDLC framing

 

 

 

 

+FTH=3

V.21 channel 2 300 bps

+FRH=3

V.21 channel 2 300

 

 

 

 

bps

 

 

 

 

 

+FTH=24

V.27ter 2400 bps

+FRH=24

V.27ter 2400 bps

 

 

 

 

+FTH=48

V.27ter 4800 bps

+FRH=48

V.27ter 4800 bps

 

 

 

 

 

 

+FTH=72

V.29

7200 bps

+FRH=72

V.29

7200 bps

 

 

 

 

 

 

+FTH=96

V.29

9600 bps

+FRH=96

V.29

9600 bps

 

 

 

 

 

 

+FTH=73

V.17

7200 bps (long

+FRH=73

V.17

7200 bps (long

 

train)

 

train)

 

 

 

 

 

 

+FTH=74

V.17

7200 bps (short

+FRH=74

V.17

7200 bps (short

 

train)

 

train)

 

 

 

 

 

 

+FTH=97

V.17

9600 bps (long

+FRH=97

V.17

9600 bps (long

 

train)

 

train)

 

 

 

 

 

+FRH=98

V.17

9600 bps (short

+FTM=145

V.17 14400 bps (long

 

train)

 

train)

 

 

 

 

 

 

+FRH=121

V.17

12000 bps (long

+FTM=146

V.17

14400 bps

 

train)

 

(short train)

 

 

 

 

 

 

8

Command

Function

Command

Function

 

 

 

 

 

+FRH=122

V.17

12000 bps (short

+FRM=n

Receive raw Fax data

 

train)

 

 

 

 

 

 

 

 

+FRH=145

V.17

14000 bps (long

+FRM=24

V.27ter 2400 bps

 

train)

 

 

 

 

 

 

 

 

+FRH=146

V.17

14000 bps (short

+FRM=48

V.27ter 4800 bps

 

train)

 

 

 

 

 

 

 

 

+FTM=n

Transmit raw FAX

+FRM=72

V.29

7200 bps

 

data

 

 

 

 

 

 

 

 

 

+FTM=24

V.27ter 2400 bps

+FRM=96

V.29

9600 bps

 

 

 

 

 

+FTM=48

V.27ter 4800 bps

+FRM=73

V.17

7200 bps (long

 

 

 

 

train)

 

 

 

 

 

 

+FTM=72

V.29

7200 bps

+FRM=74

V.17

7200 bps (short

 

 

 

 

train)

 

 

 

 

 

 

+FTM=96

V.29

9600 bps

+FRM=97

V.17

9600 bps (long

 

 

 

 

train)

 

 

 

 

 

 

+FTM=73

V.17

7200 bps (long

+FRM=98

V.17

9600 bps (short

 

train)

 

train)

 

 

 

 

 

+FTM=74

V.17

7200 bps (short

+FRM=121

V.17 12000 bps (long

 

train)

 

train)

 

 

 

 

 

 

+FTM=97

V.17

9600 bps (long

+FRM=122

V.17

12000 bps

 

train)

 

(short train)

 

 

 

 

 

+FTM=98

V.17

9600 bps (short

+FRM=145

V.17 14400 bps (long

 

train)

 

train)

 

 

 

 

 

 

+FTM=121

V.17

12000 bps (long

+FRM=146

V.17

14400 bps

 

train)

 

(short train)

 

 

 

 

 

+FTM=122

V.17

12000 bps (short

+F34=?

FAX V.34 Half

 

train)

 

Duplex

 

 

 

 

 

 

9

Note: +F34=? ---- +F34=<maxp>[[,<minp>],<prefc>] will report the current values for the parameters.

Parameters

Function

 

 

maxp:

The maximum allowed primary data rate in multiples of

 

2400 bps. The valid range is 0 to 14 inclusive, 0 means that

 

the modem will choose the maximal rate possible.

 

 

minp:

The minimum allowed primary data rate in multiples of

 

2400 bps. The valid range is 0 to 14 inclusive. 0 means that

 

the modem will choose the rate.

 

 

prefc:

The preferred control channel data rate in multiples of

 

1200 bps. The valid values are 0, 1, and 2, 0 means that the

 

modem will choose the rate.

 

 

10

S-Registers

Register

Default

Description

Range/Units

 

 

 

 

S0

0

Number of rings to auto-

0-255/rings

 

 

answer

 

 

 

 

 

S1

0

Ring counter

0-255/rings

 

 

 

 

S2

43

Escape character

0-255/ASCII

 

 

 

 

S3

13

Carriage return character

0-127/ASCII

 

 

 

 

S4

10

Line feed character

0-127/ASCII

 

 

 

 

S5

8

Backspace character

0-255/ASCII

 

 

 

 

S6

3

Wait time for dial tone

3-255/seconds

 

 

 

 

S7

50

Wait time for carrier

1-255/seconds

 

 

 

 

S8

2

Pause time for dial delay

0-255/seconds

 

 

modifier

 

 

 

 

 

S9

 

Reserved

 

 

 

 

 

S10

 

Reserved

 

 

 

 

 

S11

95

DTMF tone duration

50-255/.001

 

 

 

seconds

 

 

 

 

S12

50

Escape guard time

0-255/.02seconds

 

 

 

 

S14

138

General bit-mapped

 

 

 

options status

 

 

 

 

 

S20

0

Sync underrun fill character

0-255

 

 

 

 

S21

48

V.24/general bit-mapped

 

 

 

options status

 

 

 

 

 

S22

70

Speaker/results bit-mapped

 

 

 

options status

 

 

 

 

 

S23

54

General bit-mapped

 

 

 

options status

 

 

 

 

 

11

Register

Default

Description

Range/Units

 

 

 

 

S27

73

General bit-mapped

 

 

 

options status

 

 

 

 

 

S28

160

General bit-mapped

 

 

 

options status

 

 

 

 

 

S29

70

Flash Dial Modifier Time

0-255/.01 seconds

 

 

 

 

S30

0

Inactivity Timer

0-255

 

 

 

 

S31

10

General bit-mapped

105

 

 

options status

 

 

 

 

 

S32

17(11h)

XON character

0-255/ASCII

 

 

 

 

S33

19(13h)

XOFF character

0-255/ASCII

 

 

 

 

S35

0

Unused

 

 

 

 

 

S36

7

LAPM failure control

 

 

 

 

 

S37

0

Line connection speed

 

 

 

 

 

S48

7

V.42 negotiation control

 

 

 

 

 

S49

26(1Ah)

Link layer capabilities

 

 

 

 

 

S53

47

General bit-mapped

 

 

 

options

 

 

 

 

 

S54

2

Blind dialing delay

2-255

 

 

 

 

S91

10

PSTN transmit attenuation

6-25/dBm

 

 

level

 

 

 

 

 

S92

10

FAX transmit attenuation

6-25/dBm

 

 

level

 

 

 

 

 

S93

6

DTMF transmit attenuation

5-25/dBm

 

 

level

 

 

 

 

 

S94

0

DTMF transmit attenuation

0-25/dBm

 

 

level for high DTMF group

 

 

 

 

 

12

Result Code Summary

Long-Form Code

Short-From Code

Description

 

 

 

OK

0

Acknowledges the execution of

 

 

a command line.

 

 

 

CONNECT

1

Sent upon connecting when the

 

 

line speed is 300 bps and the

 

 

modem has been instructed to

 

 

report the line speed upon

 

 

connecting, or when the range

 

 

of result code responses is

 

 

restricted by the X command

 

 

such that no speed reporting is

 

 

allowed.

 

 

 

RING

2

Incoming ring is detected on the

 

 

line as per the interface

 

 

description.

 

 

 

NO CARRIER

3

When attempting to establish a

 

 

call, no ringback is detected

within the period of time determined by register S7, it is also used when the modem auto-disconnects due to loss of carrier. Under X0, if busy to detection is enforced, this result code is used as a response to the detection of busy or reorder. Under X0, if dial tone detection is enforced or selected, this result code is used to indicate that a dial tone has not been detected.

 

 

13

 

 

 

Long-Form Code

Short-From Code

Description

 

 

 

ERROR

4

Command line contains a syntax

 

 

error, or LU97 is unable to

 

 

execute a command contained

 

 

in a command line. This code is

 

 

issued if a command does not

 

 

exist or if the parameter

 

 

supplied is outside the

 

 

permitted range. Under X0, X1,

 

 

X2, and X3, this result is used

 

 

instead of DELAYED and

 

 

BLACKLISTED.

 

 

 

CONNECT 1200

5

For X1, X2, X3, and X4, line

 

 

speed is 1200 bps, and LU97 has

 

 

been instructed to report the

 

 

line speed upon connecting.

 

 

 

NOT DIALTONE

6

For X2 and X4, LU97 has been

 

 

instructed to wait for a dial tone

 

 

during dialing, but none is

 

 

received.

 

 

 

BUSY

7

For X3 and X4, busy tone

 

 

detection is enforced, but a busy

 

 

signal is detected when

 

 

attempting to originate a call.

 

 

 

DELAYED

88

For X4 and X5, a call fails to

 

 

connect, and the number dialed

 

 

is considered “delayed” due to

 

 

country blacklisting

 

 

requirements.

 

 

 

CONNECT 2400

10

Line speed of 2400 bits/s.

 

 

 

CONNECT 4800

11

Line speed of 4800 bits/s.

 

 

 

CONNECT 9600

12

Line speed of 9600 bits/s.

 

 

 

CONNECT 7200

24

Line speed of 7200 bits/s.

 

 

 

CONNECT 12000

25

Line speed of 12000 bits/s.

 

 

 

CONNECT 14400

13

Line speed of 14400 bits/s.

 

 

 

14

Long-Form Code

Short-From Code

Description

 

 

 

CONNECT 19200

14

Line speed of 19200 bits/s.

 

 

 

CONNECT 38400

28

Line speed of 38400 bits/s.

 

 

 

CONNECT 57600

18

Line speed of 57600 bits/s.

 

 

 

CONNECT 115200

87

Line speed of 115200 bits/s.

 

 

 

CONNECT 230400

 

Line speed of 230400 bits/s.

 

 

 

CONNECT 460800

 

Line speed of 460800 bits/s.

 

 

 

CONNECT 921600

 

Line speed of 921600 bits/s.

 

 

 

CONNECT 16800

86

Line speed of 16800 bits/s.

 

 

 

CONNECT 21600

55

Line speed of 21600 bits/s.

 

 

 

CONNECT 24000

56

Line speed of 24000 bits/s.

 

 

 

CONNECT 26400

57

Line speed of 26400 bits/s.

 

 

 

CONNECT 28800

58

Line speed of 28800 bits/s.

 

 

 

CONNECT 31200

59

Line speed of 31200 bits/s.

 

 

 

CONNECT 33600

60

Line speed of 33600 bits/s.

 

 

 

CONNECT 28000

100

Line speed of 28000 bits/s.

 

 

 

CONNECT 29333

101

Line speed of 29333 bits/s.

 

 

 

CONNECT 30666

102

Line speed of 30666 bits/s.

 

 

 

CONNECT 32000

70

Line speed of 32000 bits/s.

 

 

 

CONNECT 33333

103

Line speed of 33333 bits/s.

 

 

 

CONNECT 34666

104

Line speed of 34666 bits/s.

 

 

 

CONNECT 36000

72

Line speed of 36000 bits/s.

 

 

 

CONNECT 37333

105

Line speed of 37333 bits/s.

 

 

 

CONNECT 38666

106

Line speed of 38666 bits/s.

 

 

 

15

Long-Form Code

Short-From Code

Description

 

 

 

CONNECT 40000

74

Line speed of 40000 bits/s.

 

 

 

CONNECT 41333

107

Line speed of 41333 bits/s.

 

 

 

CONNECT 42666

108

Line speed of 42666 bits/s.

 

 

 

CONNECT 44000

76

Line speed of 44000 bits/s.

 

 

 

CONNECT 45333

109

Line speed of 45333 bits/s.

 

 

 

CONNECT 46666

110

Line speed of 46666 bits/s.

 

 

 

CONNECT 48000

78

Line speed of 48000 bits/s.

 

 

 

CONNECT 49333

111

Line speed of 49333 bits/s.

 

 

 

CONNECT 50666

112

Line speed of 50666 bits/s.

 

 

 

CONNECT 52000

80

Line speed of 52000 bits/s.

 

 

 

CONNECT 53333

113

Line speed of 53333 bits/s.

 

 

 

CONNECT 54666

114

Line speed of 54666 bits/s.

 

 

 

CONNECT 56000

82

Line speed of 56000 bits/s.

 

 

 

Note: For X1, X2, X3, and X4, codes (short-form) 9-19, 153-155, 59, 61-64, 68, 70, and 98-122, are sent when LU97 has been instructed to report the line speed when connecting, and the line speed is as indicated. These codes are also reported when the API-controlled virtual DTE speed is reported upon connection. For X1, X2, X3, and X4, Soft Mode returns these codes upon establishing a V.23 originate or answer connection when it has been instructed to report the line speed upon connection.

16

FCC Notice

This equipment complies with Part 68 of the FCC rules. Located on the bottom side of the modem is a label that contains, among other information, the FCC Registration Number and Ringer Equivalence Number (REN) for this equipment. Upon request, you must provide this information to your telephone company.

If your telephone equipment causes harm to the telephone network, the telephone company may discontinue your service temporarily. If possible, they will notify you in advance. But, if advance notice is not practical, you will be notified as soon as possible. You will also be informed of your right to file a complaint with the FCC.

Your telephone company may make changes in its facilities, equipment, operations, or procedures that could affect the proper functioning of your equipment. If they do, you will be notified in advance to give you an opportunity to maintain uninterrupted telephone service.

If this equipment should fail to operate properly, disconnect the equipment from the phone line to determine if it is causing the problem. If the problem is with the equipment, discontinue use and contact your dealer or vendor.

17

Modem manuel d’utilisation

Introduction

Ce modem V.90 interne fournit l’accès le plus rapide à Internet et aux services en ligne, et accélère plus particulièrement le téléchargement des graphiques,. le jeu en ligne, et l’informatique coopérative. C’est le fax/modem international le plus rapide sur le marché. Il est homologué dans le monde entier ce qui vous permet de configurer instantanément le modem, quel que soit le pays où vous êtes. Ce modem fonctionne sur les lignes de téléphone standard, il ne vous est donc pas nécessaire de faire des dépenses supplémentaires, en avance, et mensuelles pour des lignes spéciales.

Fonctionnalités

Taux de connexion à Internet le plus élevé, vitesse de téléchargement allant jusqu’à 56 Kbits/s, rétrocompatible avec les modems V.34

Capacités de mode données:

Taux de transfert des données ITU-T V9.0: 28000 bits/s à 56000 bits/s

Compression ultra élevée grâce à un accès parallèle directement à l’ordinateur hôte

Taux étendus ITU-T V.34: 33600 bits/s à 24000 bits/s

V.32terbo, V3.2bis

Standard TIA/EIA 602 pour le jeu de commandes AT

Correction d’erreurs V.42 (LAPM et MNP)

Compression de données V.42bis et MNP classe 5

Capacités de mode télécopie:

Standards ITU-T V.17, V.29, V.27ter, et V.21 canal 2

Télécopie TIA/EIA 578 classe 1

Appel automatique, gestion du déroulement de l’appel

Détection de sonnerie, de coupure

Faible consommation

Prise en charge de la mise à niveau logicielle au standard ITU V.92

18

Agréments mondiaux

Prise en charge logicielle

Remarque: Exécutez ce programme pour choisir le pays dans lequel vous êtes, afin que le modem puisse bien fonctionner.

Installation et test du modemm

Installation et configuration du logiciel

Installez le logiciel de communication en suivant son manuel d’utilisation et avec le même port COM et la même IRQ que ceux utilisés par le modem. Vous serez peut-être invité à configurer certains

paramètres de communication. Les valeurs suivantes sont suggérées:

Élément

Valeur suggérée

 

 

Vitesse

115200 bits/s

 

 

Bits de données

8

 

 

Parité

aucune

 

 

Bits d’arrêt

1

 

 

Contrôle de flux

Xon./Xoff

 

 

Chaîne d’initialisation

AT&F

Test de votre modem

Afin de pouvoir vérifier si le modem fonctionne de manière appropriée, assurez-vous que les valeurs du port COM et de l’IRQ de votre modem correspondent à celles de votre logiciel. Saisissez AT sur l’écran de votre terminal et appuyez sur ENTRÉE. Le modem doit répondre en affichant OK (ou 0). S’il ne le fait pas, soit le modem n’a pas été bien installé, soit le logiciel n’a pas été bien configuré.

Utilisation de votre modem

Le logiciel de communication inclus avec votre modem fournit une interface conviviale pour accéder aux données et à la télécopie. Le modem peut également accomplir des fonctions de communications de base (telles que la numérotation) par l’intermédiaire des

19

commandes AT. Veuillez consulter “Commandes AT” à la page 20 pour des descriptions détaillées. Le logiciel de communication étant conçu pour protéger l’utilisateur de la difficulté pesante des commandes AT, il est fortement conseillé de faire fonctionner le modem par l’intermédiaire du logiciel.

Dépannage

Si vous avez des problèmes d’utilisation avec votre modem, veuillez lire ce chapitre. Si vous ne pouvez pas résoudre vos difficultés après la

lecture de ce chapitre, contactez votre revendeur pour assistance.

Problème

Solution

 

 

Le modem ne

1 Assurez-vous que le logiciel de communication est

répond pas aux

configuré avec les bonnes valeurs pour le port COM

commandes.

et l’IRQ (mêmes valeurs de port COM et d’IRQ que

 

pour le modem). Votre logiciel de communication ne

 

pourra pas envoyer ni recevoir de données s’il n’est

 

pas configuré en accord en accord avec les valeurs de

 

COM et d’IRQ du modem.

 

2 Assurez-vous que votre modem est bien initialisé.

 

Votre modem peut avoir été initialisé de manière

 

inappropriée par le logiciel parce que vous avez

 

sélectionné un mauvais type de modem. Vous pouvez

 

également être invité à entrer une chaîne

 

d’initialisation par le logiciel. Utilisez la chaîne

 

d’initialisation AT&F.

 

 

Le modem

1 Assurez-vous que la valeur d’IRQ est la même pour le

numérote mais ne

modem comme pour le logiciel.

se connecte pas.

2 Assurez-vous que la ligne téléphonique fonctionne

 

de manière appropriée. Une ligne avec des parasites

 

empêche un bon fonctionnement du modem.

Le modem établit une connexion, mais aucune donnée n’apparaît à l’écran.

1Assurez-vous que les paramètres de communication (vitesse de transfert, bits de données et d’arrêt, parité) sont bien configurés et identiques des deux côtés. Assurez-vous que le contrôle du flux logiciel du modem (XON/XOFF par défaut) est activé sur le modem comme sur le logiciel de communication.

2Appuyez sur la touche ENTRÉE plusieurs fois. Le modem à distance attend peut-être de recevoir vos données avant de commencer.

Le modem rencontre

1

Assurez-vous que la fonction de signal d’appel est

des erreurs lors de la

 

désactivée.

communication avec

2

Assurez-vous d’utiliser le contrôle de flux logiciel

un modem à

 

Xon/Xoff lors du transfert des fichiers binaires.

distance.

20

Commandes AT

Commandes AT de base

Un résumé des commandes prises en charge par le modem est présenté dans le tableau suivant intitulé “Résumé du jeu de commandes AT”. Les commandes peuvent être exécutées lorsque le modem est en mode COMMAND. Le mode COMMAND est accédé lors d’une des conditions suivantes:

Après la mise sous tension

À la fin d’une connexion

Après l’exécution d’une commande autre que la numérotation ou d’une commande de réponse (ATO ou AT&T)

À la réception d’une séquence d’échappement (trois caractères consécutifs correspondant au contenu du registre S 2) pendant le mode en ligne

Lors d’une transition marche à arrêt de DTR si D1, &D2 ou &D3 a été défini

21

Résumé du jeu de commandes AT

Commande

Description

Commande

Description

 

 

 

 

A/

Répète la dernière

&Dn

Option de contrôle

 

commande

 

du terminal données

 

 

 

prêt

 

 

 

 

AT=X

Écrit dans le registre S

&Fn

Retourne à la

 

sélectionné

 

configuration par

 

 

 

défaut

 

 

 

 

AT?

Lit le registre S

&Gn

Sélectionne la

 

sélectionné

 

tonalité de grade

 

 

 

 

A

Réponse

&Kn

Contrôle de flux

 

 

 

 

Bn

Mode CCITT/Bell

&Mn

Sélection du mode

 

 

 

 

Cn

Contrôle de la

 

 

 

porteuse

 

 

 

 

 

 

Dn

Numérotation

&Pn

Contrôle de la

 

 

 

numérotation par

 

 

 

impulsion

 

 

 

 

En

Écho de la commande

&Qn

Sélection du mode

 

 

 

 

Hn

Contrôle du

&Tn

Test et diagnostics

 

décrochement et du

 

 

 

raccrochement

 

 

 

 

 

 

In

Identification du

&Sn

Option de poste de

 

modem

 

données prêt (PDP)

 

 

 

 

Ln

Volume du haut-

&V

Affiche la

 

parleur

 

configuration

 

 

 

actuelle

 

 

 

 

Mn

Contrôle du haut-

&Wn

Enregistre la

 

parleur

 

configuration

 

 

 

actuelle

 

 

 

 

On

Retourne au mode de

&Yn

Sélectionne le profil

 

données en ligne

 

de réinitialisation par

 

 

 

défaut

 

 

 

 

22

Commande

Description

Commande

Description

 

 

 

 

P

Numérotation par

&Zn=x

Enregistre le numéro

 

impulsion par défaut

 

de téléphone

 

 

 

 

Qn

Contrôle du code de

%En

Contrôle

 

résultat

 

automatique reprise/

 

 

 

abandon

 

 

 

 

Sn

Accède au registre S

\An

Sélectionne la taille

 

 

 

maximale de bloc

 

 

 

MNP

 

 

 

 

T

Numérotation par

\Bn

Transmet la coupure

 

tonalité par défaut

 

à distance

 

 

 

 

Vn

Forme du code de

\Jn

Ajustement du taux

 

résultat

 

de I’ETCD

 

 

 

 

Wn

Contrôle du code de

\Kn

Contrôle de la

 

résultat de connexion

 

coupure

 

 

 

 

Xn

Contrôle du code de

&Cn

Contrôle de détection

 

résultat étendu

 

de la porteuse

 

 

 

 

Yn

Déconnexion à long

Zn

Réinitialisation

 

espacement

 

 

 

 

 

 

23

Tableau des commandes FAX

Commande

Fonction

Commande

Fonction

 

 

 

 

 

+FCLASS=n

Sélection de la classe de

+FTH=98

V.17

9600 bits/s

 

service

 

(porteuse courte)

 

 

 

 

 

+FCLASS=0

Sélection du mode

+FTH=121

V.17

12000 bits/s

 

données (Défaut)

 

(porteuse longue)

 

 

 

 

 

+FCLASS=1

Sélection du FAX

+FTH=122

V.17

1200 bits/s

 

Classe 1

 

(porteuse courte)

 

 

 

 

 

+FTS=n

Arrêt de la transmission

+FTH=145

V.17

14400 bits/s

 

et pause

 

(porteuse longue)

 

 

 

 

 

+FRS=n

Réception d’un silence

+FTH=146

V.17

14400 bits/s

 

 

 

 

(porteuse courte)

 

 

 

 

+FTH=n

Transmission des

+FRH=n

Réception des données

 

données en cadre HDLC

 

en cadre HDLC

 

 

 

 

+FTH=3

V.21 canal 2300 bits/s

+FRH=3

V.21 canal 2300 bits/s

 

 

 

 

+FTH=24

V.27ter 2400 bits/s

+FRH=24

V.27ter 2400 bits/s

 

 

 

 

+FTH=48

V.27ter 4800 bits/s

+FRH=48

V.27ter 4800 bits/s

 

 

 

 

 

 

+FTH=72

V.29

7200 bits/s

+FRH=72

V.29

7200 bits/s

 

 

 

 

 

 

+FTH=96

V.29

9600 bits/s

+FRH=96

V.29

9600 bits/s

 

 

 

 

 

 

+FTH=73

V.17

7200 bits/s

+FRH=73

V.17

7200 bits/s

 

(porteuse longue)

 

(porteuse longue)

 

 

 

 

 

 

+FTH=74

V.17

7200 bits/s

+FRH=74

V.17

7200 bits/s

 

(porteuse courte)

 

(porteuse courte)

 

 

 

 

 

 

+FTH=97

V.17

9600 bits/s

+FRH=97

V.17

9600 bits/s

 

(porteuse longue)

 

(porteuse longue)

 

 

 

 

 

 

+FRH=98

V.17

9600 bits/s

+FTM=145

V.17

14400 bits/s

 

(porteuse courte)

 

(porteuse longue)

 

 

 

 

 

 

+FRH=121

V.17

12000 bits/s

+FTM=146

V.17

14400 bits/s

 

(porteuse longue)

 

(porteuse courte)

 

 

 

 

+FRH=122

V.17 12000 bits/s

+FRM=n

Réception de

 

(porteuse courte)

 

données FAX brutes

 

 

 

 

 

+FRH=145

V.17

14400 bits/s

+FRM=24

V.27ter 2400 bits/s

(porteuse longue)

Loading...
+ 57 hidden pages