Size:
220.32 Kb
Download

Table of Contents

 

Important Safety Instructions..............................................................................

3

Federal Communications Commission ................................................................

4

Connecting the Monitor and Swivel Base ..........................................................

5

Removing the Monitor and Swivel Base ............................................................

5

Introduction...........................................................................................................

6

Installation.............................................................................................................

7

User Controls.........................................................................................................

8

Adjusting the Brightness and Contrast...............................................................

9

OSD Function Description ....................................................................................

9

OSD Icon Summary .............................................................................................

10

Specification ........................................................................................................

11

Troubleshooting..................................................................................................

12

2

Important Safety Instructions

1.Please read these instructions thoroughly.

2.Please keep this guide for future use.

3.Please disconnect the device from the main power supply before cleaning. Do not use any liquids or aerosol sprays to clean this device. Use a clean dampened cloth in stead.

4.To avoid damaging the device, only use factory-approvedaccessories.

5.Protect the device against moisture.

6.In order to set up the device, first place it on a stable surface. Tipping it over or dropping can harm the monitor and cause injuries. Please follow the setup instructions of the manufacturer while setting up your monitor.

7.The ventilation openings are used for air circulation to protect the device against overheating.

8.When connecting the device, obey the maximum connected load values of the main power supply.

9.The wall socket must be equipped with a non-fusedgrounded conductor contact for electrical safety.

10.The power cable must be laid in such a way nobody can trip over it. Please do not place any objects on the cable.

11.Follow all instructions and warning remarks that are printed on the device.

12.If the device will not be used for a long period of time, please disconnect it from the main power supply to avoid power surge damage such as lightning.

13.Make sure no sharp objects or liquids enter the device via its air circulation openings. This could result in a fire or an electric shock.

14.Never open the device casing yourself, there are no user serviceable parts inside. Only authorized technical service personnel should open the casing of this device.

15.If any of the following conditions occur, the device must be disconnected from the main supply, and be checked by a qualified service center:

a- Power cable or power plug are damaged;b- Liquid has entered the device;

c- The device was exposed to moisture;

d- The device does not operate according to the user’s guide, or you do not achieve any improvement with the aid of this guide;

e- The device has been dropped and/or the casing is damaged;f- The device shows obvious signs of a defect.

16.Use only approved original spare parts, or parts in accordance with the original parts, for repairs. The use of incorrect/unauthorized spare parts may cause further damage.

17.Please contact your service center for any questions regarding service and repairs to guarantee the device’s performance and reliability.

18.The power socket must be installed near the equipment to be easily accessible.

3

Federal Communications Commission

( FCC Statement )

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorientate or relocate the receiving antenna;

Increase the separation between the equipment and receiver;

Connect the equipment with a power socket on a circuit different from that to which the receiver is connected;

Consult the dealer or an experienced radio/TV technician for help.

Any changes or modifications not expressly approved by the manufacturers may void the user’s authority to operate this equipment.

A shielded-typevideo signal cable is required in order to meet the FCC emission limits and also to prevent interference to nearby radio and television reception. It is essential that only the supplied power cord be used.

Use only shielded cables to connect I/O devices to this equipment.

Canadian DOC Notice

For Class B Computing Devices

This Class B digital apparatus meets all requirements of the Canadian InterferenceCausing Equipment Regulations.

Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.

4

Connecting the Monitor and Swivel Base

1.Place the monitor with its tube down on a stable surface.

2.Align the four tabs of the swivel base with the slots in the bottom of the monitor.

3.Insert the tabs into the slots of the monitor

4.Now slowly slide the swivel base toward the front of the monitor till you hear the spring lock click into place.

Removing the Monitor and Swivel Base

If you need to remove the swivel base, push the spring lock and then pull the swivel base away from the monitor.

NOTE: Special attention should be paid to the control knobs and LED indicators on the front panel when you place the monitor with its tube down. This will prevent damage to these control knobs and LED indicators from excessive pressure.

5

Introduction

Congratulations on your purchase of this new high performance 15” Monitor. Using state-of-the-artelectronics, this monitor supports a 1280 x 1024 resolution. Theon-screendisplay allows you to customize the display settings to suit your individual taste.

Features

15-inchmonitor with a large, viewable screen for comfortable viewing.

OSD user controls for easy and accurate adjustment of the screen image.

Energy Star compliant for reduced power consumption.

Package Overview

Please make sure the following items are in the packing it was shipped in, and found in good working condition:

15” Monitor

Power Cord

Tilt and Swivel Base

This User’s manual

Please contact your dealer or nearest service centers if any of the above items is missing or damaged.

6

Installation

1.Connect the monitor signal cable 1 to the15-pinminiD-sub(VGA) on the back of the computer.

2.Connect the power cord to the power connector on the back panel of the monitor, then plug the other end into an electrical outlet that is easily accessible, and close to the monitor.

3.First turn on the power of the computer, then that of the monitor.

4.Adjust the tilt of the swivel base for maximum viewing comfort.

The installation of your monitor is now complete.

7

User Controls

Control

Function

Power Switch

Turns the monitor on

Power LED Indicator

GreenOn

AmberSleep

 

OSD ON/OFF Control

Turn the OSD Display ON or OFF

Brightness Control/ OSD

Adjust Brightness level or OSD

Function selection

Function selection Control

Contrast Control/OSD

Adjust Contract level or OSD Function

Function adjustment

Level Control

8

Adjusting the Brightness and Contrast

To adjust the contrast and/or brightness, Press the Contrast Control or theBrightness Control, to call up the followingon-screendisplay:

OSD Function Description

1. Press the OSD On/Off control buttonto display the OSD Menu.

2.

To select

function, press

button until the function you want is

 

highlighted.

 

3.

Use the

button to increase or decrease the adjustment of this

 

function.

 

 

4.If you want to exit the OSD function then press the OSD On/Off control buttononce.

9

OSD Icon Summary

Icon

Function

Function Description

 

 

 

 

Brightness

Adjusts display brightness

 

 

 

 

Contrast

Adjusts display contrast

 

 

 

 

H. Size

Increases and decreases screen width

 

 

 

 

H. Position

Shifts display image right or left

 

 

 

 

V. Size

Increase and decrease screen height

 

 

 

 

V. Position

Shifts display image up or down

 

 

 

 

Pincushion

Adjusts concave and convex portion of

 

pincushion effect

 

 

 

Trapezoid

Adjusts the top and bottom display widths

 

 

 

 

Rotation

Adjusts the rotation of the display clock or

 

anti-clockwise

 

 

 

Parallelogram

Adjusts the tilt of the display sides to the left

 

or right

 

 

 

Reset

Resets to default values

 

 

 

 

Degauss

Demagnetizes the screen to reduce color

 

 

impurities

 

 

 

10