4RF XE757M170 User Manual

Loading...

August 2017

Version 8.8.84a

Copyright

Copyright © 2017 4RF Limited. All rights reserved.

This document is protected by copyright belonging to 4RF Limited and may not be reproduced or republished in whole or part in any form without the prior written permission of 4RF Limited.

Trademarks

Aprisa and the 4RF logo are trademarks of 4RF Limited.

Windows is a registered trademark of Microsoft Corporation in the United States and other countries. Java and all Java-related trademarks are trademarks or registered trademarks of Sun Microsystems, Inc. in the United States and other countries. All other marks are the property of their respective owners.

GoAhead WebServer. Copyright © 2000 GoAhead Software, Inc. All Rights Reserved.

Disclaimer

Although every precaution has been taken preparing this information, 4RF Limited assumes no liability for errors and omissions, or any damages resulting from use of this information. This document or the equipment may change, without notice, in the interests of improving the product.

RoHS and WEEE compliance

The Aprisa XE is fully compliant with the European Commission’s RoHS (Restriction of Certain Hazardous

Substances in Electrical and Electronic Equipment) and WEEE (Waste Electrical and Electronic Equipment) environmental directives.

Restriction of hazardous substances (RoHS)

The RoHS Directive prohibits the sale in the European Union of electronic equipment containing these hazardous substances: lead*, cadmium, mercury, hexavalent chromium, polybrominated biphenyls (PBBs), and polybrominated diphenyl ethers (PBDEs).

4RF Limited has worked with its component suppliers to ensure compliance with the RoHS Directive which came into effect on the 1st July 2006.

*The European Commission Technical Adaptation Committee (TAC) has exempted lead in solder for highreliability applications for which viable lead-free alternatives have not yet been identified. The exemption covers communications network infrastructure equipment, which includes 4RF Limited’ Aprisa XE microwave radios.

End-of-life recycling programme (WEEE)

The WEEE Directive concerns the recovery, reuse, and recycling of electronic and electrical equipment. Under the Directive, used equipment must be marked, collected separately, and disposed of properly.

4RF Limited has instigated a programme to manage the reuse, recycling, and recovery of waste in an environmentally safe manner using processes that comply with the WEEE Directive (EU Waste Electrical and Electronic Equipment 2002/96/EC).

4RF Limited invites questions from customers and partners on its environmental programmes and compliance with the European Commission’s Directives (sales@4RF.com).

Aprisa XE Product Description 8.8.84 NA

Compliance general

The Aprisa XE digital radio predominantly operates within frequency bands that require a site license be issued by the radio regulatory authority with jurisdiction over the territory in which the equipment is being operated.

It is the responsibility of the user, before operating the equipment, to ensure that where required the appropriate license has been granted and all conditions attendant to that license have been met.

Changes or modifications not approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Equipment authorizations sought by 4RF Limited are based on the Aprisa XE radio equipment being installed at a fixed restricted access location and operated in a continuous point-to-point mode within the environmental profile defined by EN 300 019, Class 3.2. Operation outside these criteria may invalidate the authorizations and / or license conditions.

The term ‘Terminal’ with reference to the Aprisa XE User Manual, is a generic term for one end of a fixed point-to-point Aprisa XE link and does not confer any rights to connect to any public network or to operate the equipment within any territory.

Aprisa XE Product Description 8.8.84 NA

Compliance FCC

The Aprisa XE radio terminal is designed to comply with the Federal Communications Commission (FCC) specifications as follows:

Radio

 

47CFR part 90 Private Land Mobile Radio Services

 

 

47CFR part 101 Fixed Microwave Services

 

 

47CFR part 27 Misc Wireless Communication Services

 

 

 

 

 

 

EMC

 

47CFR part 15 Radio Frequency Devices

 

 

 

 

 

 

 

Environmental

 

EN 300 019, Class 3.4

 

 

 

 

 

 

 

Safety

 

EN 60950-1:2006

 

 

 

 

 

 

 

 

 

 

 

 

 

Frequency band

Channel

Power

Authorization

 

FCC ID

limits

size

input

 

 

 

 

 

 

 

 

 

 

421 to 512 MHz

25 kHz

48

VDC

Part 90 Certification

 

UIPN0400025A0200A

 

 

 

 

 

 

 

Lower 700 MHz

500 kHz,

24

VDC,

Part 27 Certification

 

UIPN0700AAAA0000A

698 to 746 MHz

1.0 MHz

48

VDC,

 

 

 

 

1.75 MHz

110 VAC

 

 

 

 

 

 

 

 

 

 

Upper Block A 700 MHz

100 kHz,

24

VDC,

Part 27 Certification

 

Pending

757 to 758 MHz

200 kHz

48

VDC,

 

 

 

787 to 788 MHz

500 kHz

110 VAC

 

 

 

 

 

 

 

 

 

 

932.5 to 960 MHz

100 kHz,

24

VDC,

Part 101 Verification

 

-

 

200 kHz

48

VDC,

 

 

 

 

 

110 VAC

 

 

 

 

 

 

 

 

 

 

2314.5 to 2317.5 MHz

250 kHz,

24

VDC,

Part 27 Certification

 

UIPN2500AAAA0200A

2346.5 to 2349.5 MHz

500 kHz

48

VDC,

 

 

 

 

 

110 VAC

 

 

 

 

 

 

 

 

 

2180 to 2290 MHz

500 kHz

110 VAC

Part 101 Certification

 

UIPXE20001300

 

 

 

 

 

 

 

NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Aprisa XE Product Description 8.8.84 NA

Compliance Industry Canada

The Aprisa XE radio terminal is designed to comply with Industry Canada (IC) specifications as follows:

Radio

 

RSS-GEN

 

 

 

 

RSS-119

 

 

 

 

 

 

 

 

EMC

 

This Class A digital apparatus complies with Canadian

 

 

standard ICES-003.

 

 

 

 

Cet appareil numérique de la classe A est conforme à la

 

 

norme NMB-003 du Canada.

 

 

 

 

 

 

 

 

Environmental

 

EN 300 019, Class 3.4

 

 

 

 

 

 

 

 

 

Safety

 

EN 60950-1:2006

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Frequency Band

Channel size

Power

 

Authorization

IC ID

 

 

 

input

 

 

 

 

 

 

 

 

 

406.1 to 430 MHz and

25 kHz, 50 kHz

24 VDC,

 

RSS-119

6772A-N04AAAEC

450 to 470 MHz

75 kHz, 150 kHz

48 VDC,

 

 

 

 

 

 

110 VAC

 

 

 

 

 

 

 

 

 

932.5 to 944 MHz

100 kHz,

24 VDC,

 

RSS-119

6772A-N09AAACC

 

200 kHz

48 VDC,

 

 

 

 

 

 

110 VAC

 

 

 

 

 

 

 

 

 

1427 to 1452 MHz and

3.50 MHz

24 VDC,

 

SRSP-301.4

 

1492 to 1518 MHz

 

 

48 VDC,

 

 

 

 

 

 

110 VAC

 

 

 

 

 

 

 

 

 

2025 to 2110 MHz and

500 kHz, 1.0 MHz,

24 VDC,

 

SRSP-302.0

 

2200 to 2285 MHz

1.75 MHz, 3.50 MHz,

48 VDC,

 

 

 

 

7 MHz

110 VAC

 

 

 

 

 

 

 

 

 

 

Aprisa XE Product Description 8.8.84 NA

RF Exposure Warning

WARNING:

The installer and / or user of Aprisa XE radio terminals shall ensure that a separation distance as given in the following table is maintained between the main axis of the terminal’s antenna and the body of the user or nearby persons.

Minimum separation distances given are based on the maximum values of the following methodologies:

1.Maximum Permissible Exposure non-occupational limit (B or general public) of

47 CFR 1.1310 and the methodology of FCC’s OST/OET Bulletin number 65.

2.Reference levels as given in Annex III, European Directive on the limitation of exposure of the general public to electromagnetic fields (0 Hz to 300 GHz) (1999/519/EC). These distances will ensure indirect compliance with the requirements of EN 50385:2002.

Frequency

Maximum power

Maximum

Maximum power

Minimum

(MHz)

(dBm)

antenna gain

density

separation

 

 

(dBi)

(mW/cm2)

distance

 

 

 

 

(m)

 

 

 

 

 

400

+ 35

15

0.20

2.0

 

 

 

 

 

512

+ 35

15

0.26

1.8

 

 

 

 

 

715

+ 34

10

0.23

1.0

 

 

 

 

 

806

+ 34

28

0.40

5.6

 

 

 

 

 

890

+ 34

28

0.45

5.3

 

 

 

 

 

960

+ 34

28

0.48

5.1

 

 

 

 

 

1550

+ 34

33

0.78

7.2

 

 

 

 

 

 

 

DRAFT

 

 

2300

+ 34

37

1.00

10.0

2700

+ 34

38

1.00

11.2

Aprisa XE Product Description 8.8.84 NA

Contents

 

1.

Introduction................................................................................

1

 

The 4RF Aprisa XE Terminal ....................................................................

1

 

Key Features ......................................................................................

2

 

Robust Transmission Performance ......................................................

3

 

Flexible Multiplexing......................................................................

3

 

Interface Types ............................................................................

3

 

In-built Cross-Connect ....................................................................

4

 

RF Specifications .................................................................................

5

 

Radios FCC..................................................................................

5

 

Radios IC ...................................................................................

11

 

Duplexers ..................................................................................

17

 

Protection System Specifications .............................................................

18

 

MHSB Protection..........................................................................

18

 

HSD Protection............................................................................

18

 

Power Specifications............................................................................

19

 

AC Power Supply..........................................................................

19

 

DC Power Supply..........................................................................

19

 

Power Consumption ......................................................................

20

 

Environmental ............................................................................

22

 

Mechanical ................................................................................

22

 

Compliance................................................................................

23

2.

Applications ..............................................................................

25

 

Extending Telecommunications and Cellular Networks....................................

26

 

Delivering POTS and Broadband to Remote Subscribers ...................................

27

 

Extending DSL Services in Remote Areas.....................................................

28

 

Supporting Mobile Radio Networks............................................................

29

 

Digital Mobile Radio Networks..........................................................

29

 

Analogue Trunked Radio.................................................................

29

 

Conventional Radio ......................................................................

30

 

Supporting Utility Networks ...................................................................

31

 

Linking Offices in Private Networks ..........................................................

32

Aprisa XE Product Description 8.8.84 NA

3.

Architecture .............................................................................

33

 

Modules ...........................................................................................

33

 

Front Panel Connections and Indicators .....................................................

35

 

Transceiver.......................................................................................

36

 

Receiver ...................................................................................

36

 

Transmitter................................................................................

37

 

Duplexer ..........................................................................................

37

 

Modem ............................................................................................

38

 

Motherboard .....................................................................................

39

 

Power Supplies...................................................................................

40

 

AC Power Supply..........................................................................

40

 

DC Power Supply..........................................................................

40

 

Mounting Options................................................................................

40

 

Heat Dissipation .................................................................................

40

4.

Interfaces .................................................................................

41

 

Interface Specifications ........................................................................

41

 

Ethernet Interface Connections ...............................................................

41

 

QETH Interface Connections ...................................................................

42

 

QJET Quad E1 / T1 Interface ...........................................................

44

 

Q4EM Quad 4 Wire E&M Interface......................................................

45

 

DFXO Dual Foreign Exchange Office Interface .......................................

49

 

DFXS Dual Foreign Exchange Subscriber Interface...................................

51

 

QV24 Quad V.24 Serial Data Interface ................................................

53

 

HSS Single High Speed Synchronous Interface........................................

55

5.

SuperVisor ................................................................................

59

 

Configuring the Aprisa XE Terminal...........................................................

59

 

Monitoring the Aprisa XE Terminal............................................................

59

 

Operator Rights and Access Levels............................................................

60

 

Viewing the Status of the Link ................................................................

60

 

Configuring the Basic Terminal Settings .....................................................

61

 

Configuring the Interface Ports and Cross Connect ........................................

62

 

Interface Ports............................................................................

62

 

Loopback Functionality..................................................................

63

 

Configuring the Cross Connects ........................................................

63

 

Monitoring Performance and Troubleshooting Problems ..................................

64

6.

Network Management..................................................................

67

7.

Protected Options ......................................................................

69

 

Monitored Hot Stand By (MHSB) ...............................................................

69

 

Hitless Space Diversity (HSD) ..................................................................

71

Aprisa XE Product Description 8.8.84 NA

Introduction | 1

1.Introduction

The 4RF Aprisa XE Terminal

The 4RF Aprisa XE point-to-point digital access radio provides robust wireless transmission of Internet, voice and data traffic over distances of up to 250 kilometres.

The Aprisa XE Terminal is the flexible, functional answer to the low-medium capacity challenges in today’s wireless networks.

Easy to use and customer-configurable, the Aprisa XE terminal provides solutions from simple trunking applications to complete complex network designs.

Our design priority is to reduce network operators’ costs. To this end, we engineer into all Aprisa XE terminals high-performance characteristics and operating features that deliver:

Superior spectral efficiency

Customer-configurable interfaces

Straightforward integration into existing networks

The SuperVisorTM software is an embedded element manager for the Aprisa XE terminal, meaning that is easily accessed using any standards-compliant web browser.

The SuperVisor software is graphical and intuitive, and requires no ongoing training. SNMP connectivity is standard with the SuperVisor software, allowing easy integration of the Aprisa XE terminal into higherlevel management systems.

The Aprisa XE terminal is small and powerful, with eight interface slots and up to 65 Mbit/s of capacity, ideal for use in busy network sites where vertical rack space is limited.

Aprisa XE Product Description 8.8.84 NA

4RF XE757M170 User Manual

2 | Introduction

Key Features

Spectrally efficient 16, 32 and 64 QAM modulation types

QPSK modulation for higher system gain

Capacities from 72 kbit/s (1 x timeslot) to 65 Mbit/s (32 x E1)

Channel sizes from 25 kHz to 14 MHz

A full E1 (2 Mbit/s) bearer in just 500 kHz of spectrum (64 QAM)

In-built 4-port Ethernet switch

In-built digital cross-connect with 8 kbit/s granularity

Frequency bands from 300 MHz to 2.7 GHz

Customer-configurable interface options for data and voice traffic

19-inch rack mounting

Complies with international standards, including ETSI, FCC and Industry Canada

Modular design to reduce the mean time to repair (MTTR)

Embedded Java™-enabled element management software (the SuperVisor software)

Integrated SNMP for network management

Protection options of Monitored Hot Standby (MHSB) and Hitless Space Diversity (HSD)

Aprisa XE Product Description 8.8.84 NA

Introduction | 3

Robust Transmission Performance

The Aprisa XE terminal provides robust, reliable, ‘carrier-class’ transmission performance for long and challenging paths:

Reed-Solomon Forward Error Correction delivers an unfaded BER of 10-12 , a performance more commonly associated with fibre optics.

Multi-tap equalizers optimize multi-path performance.

Advanced digital filters provide optimum protection against adjacent channel interference, and allow maximum frequency reuse.

Spectrum-efficient 16, 32 and 64 QAM modulation maximizes data throughput in narrow radio channels, thereby reducing frequency licensing costs.

QPSK modulation provides increased gain for very long obstructed paths.

Flexible Multiplexing

The Aprisa XE terminal provides primary multiplexing options without the need for external equipment. It features eight interface card slots and an in-built cross-connect.

Interface Types

The Aprisa XE terminal’s range of analogue and digital customer interface types makes it suitable for many applications.

It comes with an in-built 4-port Ethernet switch, which supports VLAN tagging and QoS for customer and management traffic.

Other interface card options include:

QETH Quad port Ethernet interface card supporting 10Base-T or 100Base-TX for transport of user Ethernet traffic

DFXO Dual 2 wire Foreign Exchange Office (PCM / ADPCM)

DFXS Dual 2 wire Foreign Exchange Subscriber (PCM / ADPCM)

Q4EM Quad 4 wire E&M (PCM / ADPCM)

QJET Quad E1 / T1 - G.703 / G.704

QV24 Quad V.24 asynchronous and synchronous Serial Data Interface.

HSS Single Synchronous Serial interface including V.35, X.21, RS-449 and RS-530

Aprisa XE Product Description 8.8.84 NA

4 | Introduction

In-built Cross-Connect

The Aprisa XE terminal’s in-built micro cross-connect distributes capacity to each of the interfaces. It can distribute traffic to any of the possible 32 interface ports as well as the integrated Ethernet interface. This allows operators to reconfigure traffic as network demand changes, and to groom user traffic onto E1 bearers between equipment.

For example, a typical E1 bearer can be distributed as follows:

Four 64 kbit/s PCM 2 wire voice circuits

CAS signalling using 64 kbit/s

Four 9600 bit/s V.24 circuits, each using 24 kbit/s

One X.21 circuit using 128 kbit/s

One Ethernet 100/10Base-T circuit using 384 kbit/s

16 timeslots for fractional E1 traffic using 1024 kbit/s

One management channel using 64 kbit/s

Aprisa XE Product Description 8.8.84 NA

 

 

 

 

 

 

 

Introduction | 5

RF Specifications

 

 

 

 

 

 

Radios FCC

 

 

 

 

 

 

Frequency Bands FCC

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Frequency Bands

 

Frequency

 

Frequency

Synthesizer

 

 

 

Band

 

Tuning Range

Step Size

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

400 MHz

 

421 - 512 MHz

6.25 kHz

 

 

 

 

 

 

 

 

 

 

 

 

 

Lower 700 MHz

 

698 - 746 MHz

12.5 kHz

 

 

 

 

 

 

 

 

 

 

 

 

 

Upper Block A 700 MHz

 

757 – 758 and

12.5 kHz

 

 

 

 

 

787 – 788 MHz

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

900 MHz

 

928 - 960 MHz

12.5 kHz

 

 

 

 

 

 

 

 

 

 

 

 

 

1800 MHz

 

1755 - 1850 MHz

62.5 kHz

 

 

 

 

 

 

 

 

 

 

 

 

 

2000 MHz

 

1900 - 2300 MHz

62.5 kHz

 

 

 

 

 

 

 

 

 

 

 

 

2500 MHz

250 / 500 kHz channels

 

2314 - 2350 MHz

62.5 kHz

 

 

 

 

 

 

 

 

 

 

 

2500 MHz All other channels

 

2305 - 2360 MHz

62.5 kHz

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Modulation

 

16 / 32 / 64 QAM and QPSK (software configurable)

 

 

 

 

 

 

 

 

 

Frequency stability (short term)

 

< ±1 ppm

 

 

 

 

 

 

 

 

 

 

 

Frequency stability (long term)

 

< ±2 ppm

 

 

 

 

 

 

 

 

 

 

Antenna connector

 

N-type female 50 Ω

 

 

 

 

 

 

 

 

 

 

 

Notes

Frequency Ranges

Country specific frequency ranges within the above tuning ranges can be accommodated

Frequency stability

Short term frequency stability is defined as changes in frequency due to environmental effects and power supply variations

Long term frequency stability is defined as changes in frequency due to aging of crystal oscillators approx over 5 years

Aprisa XE Product Description 8.8.84 NA

6 | Introduction

Product Range FCC

The Aprisa XE terminal provides the following FCC frequency bands / channel sizes:

 

Channel Size

kHz

MHz

Frequency Band MHz

 

25

50

100

200

250

500

1.00

1.75

 

 

 

 

 

 

 

 

 

400

Part 90

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

700

 

 

Part 27

Part 27

 

Part 27

Part 27

Part 27

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

900

Part 101

Part 101

Part 101

Part 101

 

 

 

 

 

 

 

 

 

 

 

 

 

2500

 

Part 27

Part 27

 

 

 

 

 

 

Released

Product Release Pending

Aprisa XE Product Description 8.8.84 NA

 

 

 

 

 

 

Introduction | 7

Link Capacity FCC part 27

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Channel size

 

QPSK

16 QAM

32 QAM

64 QAM

 

 

 

 

 

 

 

 

 

 

100 kHz

Gross

168 kbit/s

344 kbit/s

432 kbit/s

520 kbit/s

 

 

 

T1

2 timeslots

5 timeslots

6 timeslots

8 timeslots

 

 

 

Wayside

40 kbit/s

24 kbit/s

48 kbit/s

8 kbit/s

 

 

 

 

 

 

 

 

 

 

200 kHz

Gross

336 kbit/s

680 kbit/s

840 kbit/s

1024 kbit/s

 

 

 

T1

5 timeslots

10 timeslots

13 timeslots

16 timeslots

 

 

 

Wayside

16 kbit/s

40 kbit/s

8 kbit/s

0 kbit/s

 

 

 

 

 

 

 

 

 

 

250 kHz

Gross

408 kbit/s

824 kbit/s

1032 kbit/s

1240 kbit/s

 

 

 

 

 

 

 

 

 

 

 

T1

6 timeslots

12 timeslots

16 timeslots

19 timeslots

 

 

 

Wayside

24 kbit/s

56 kbit/s

8 kbit/s

24 kbit/s

 

 

 

 

 

 

 

 

 

 

500 kHz

Gross

792 kbit/s

1592 kbit/s

1992 kbit/s

2392 kbit/s

 

 

 

T1

12 timeslots

1 T1

1 T1

1 T1

 

 

 

Wayside

24 kbit/s

8 kbit/s

408 kbit/s

808 kbit/s

 

 

 

 

 

 

 

 

 

 

1.0 MHz

Gross

1656 kbit/s

3320 kbit/s

4152 kbit/s

4984 kbit/s

 

 

 

T1

1 T1

2 T1s

2 T1s

3 T1s

 

 

 

Wayside

72 kbit/s

152 kbit/s

984 kbit/s

232 kbit/s

 

 

 

 

 

 

 

 

 

 

1.75 MHz

Gross

2872 kbit/s

5752 kbit/s

7192 kbit/s

8632 kbit/s

 

 

 

T1

1 T1

3 T1s

4 T1s

5 T1s

 

 

 

Wayside

1288 kbit/s

1000 kbit/s

856 kbit/s

712 kbit/s

 

 

 

 

 

 

 

 

 

Link Capacity FCC part 90

 

 

 

 

 

 

 

 

 

 

 

 

 

Channel size

 

QPSK

16 QAM

32 QAM

64 QAM

 

 

 

 

 

 

 

 

 

 

25 kHz

Gross

 

56 kbit/s

72 kbit/s

88 kbit/s

 

 

 

T1

 

0 timeslots

1 timeslot

1 timeslot

 

 

 

Wayside

 

56 kbit/s

8 kbit/s

24 kbit/s

 

 

 

 

 

 

 

 

 

Link Capacity FCC part 101

 

 

 

 

 

 

 

 

 

 

 

 

 

Channel size

 

QPSK

16 QAM

32 QAM

64 QAM

 

 

 

 

 

 

 

 

 

 

25 kHz

Gross

 

72 kbit/s

96 kbit/s

112 kbit/s

 

 

 

T1

 

1 timeslot

1 timeslot

1 timeslot

 

 

 

Wayside

 

8 kbit/s

32 kbit/s

48 kbit/s

 

 

 

 

 

 

 

 

 

 

50 kHz

Gross

80 kbit/s

168 kbit/s

208 kbit/s

256 kbit/s

 

 

 

T1

1 timeslot

2 timeslots

3 timeslots

4 timeslots

 

 

 

Wayside

16 kbit/s

40 kbit/s

16 kbit/s

0 kbit/s

 

 

 

 

 

 

 

 

 

 

100 kHz

Gross

136 kbit/s

280 kbit/s

352 kbit/s

424 kbit/s

 

 

 

T1

2 timeslots

4 timeslots

5 timeslots

6 timeslots

 

 

 

 

 

 

 

 

 

 

 

Wayside

8 kbit/s

24 kbit/s

32 kbit/s

40 kbit/s

 

 

 

 

 

 

 

 

 

 

200 kHz

Gross

312 kbit/s

632 kbit/s

792 kbit/s

952 kbit/s

 

 

 

T1

4 timeslots

9 timeslots

12 timeslots

14 timeslots

 

 

 

Wayside

56 kbit/s

56 kbit/s

24 kbit/s

56 kbit/s

 

 

 

 

 

 

 

 

 

Notes The capacities specified are for unframed T1 and so require 1584 kbit/s to transport via the radio. The management ethernet capacity must be subtracted from the gross capacity (default 64 kbit/s). See Product Range table for Channel Size / Frequency Band cross reference

NA (Not Available)

Aprisa XE Product Description 8.8.84 NA

8 | Introduction

Receiver Sensitivity FCC

 

Channel size

 

QPSK

 

16 QAM

 

 

32 QAM

 

64 QAM

 

 

 

 

 

 

 

 

 

 

 

 

25 kHz

 

NA

 

-105 dBm

 

 

-102 dBm

 

-99 dBm

 

 

 

 

 

 

 

 

 

 

 

 

50 kHz

 

-109 dBm

 

-103 dBm

 

 

-100 dBm

 

-97 dBm

 

 

 

 

 

 

 

 

 

 

 

 

100 kHz

 

-106 dBm

 

-100 dBm

 

 

-97 dBm

 

-94 dBm

 

 

 

 

 

 

 

 

 

 

 

 

200 kHz

 

-102 dBm

 

-96 dBm

 

 

-93 dBm

 

-90 dBm

 

 

 

 

 

 

 

 

 

 

 

 

250 kHz

 

-101 dBm

 

-95 dBm

 

 

-92 dBm

 

-89 dBm

 

 

 

 

 

 

 

 

 

 

 

 

500 kHz

 

-99 dBm

 

-93 dBm

 

 

-90 dBm

 

-87 dBm

 

 

 

 

 

 

 

 

 

 

 

 

1.0 MHz

 

-96 dBm

 

-90 dBm

 

 

-87 dBm

 

-84 dBm

 

 

 

 

 

 

 

 

 

 

 

 

1.75 MHz

 

-94 dBm

 

-88 dBm

 

 

-85 dBm

 

-82 dBm

 

 

 

 

 

 

 

 

 

 

 

Notes Typical performance specified at the antenna port for 10-6 BER.

 

 

 

The receiver is typically 1 dB more sensitive for a BER of 10-3.

 

 

 

NA (Not Available)

 

 

 

 

 

 

 

 

 

 

Transmitter Power FCC

 

 

 

 

 

 

 

 

 

 

1+0 Radio

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Frequency Band

QPSK

16 QAM

 

32 QAM

 

64 QAM

 

 

 

 

 

 

 

 

 

 

400

MHz

NA

17 to 31 dBm

 

15 to 29 dBm

 

15 to 29 dBm

 

 

 

 

 

 

 

 

 

Lower 700 MHz

21 to 35 dBm

17 to 31 dBm

 

15 to 29 dBm

 

15 to 29 dBm

 

 

 

 

 

 

 

 

 

Upper 700 MHz

21 to 31 dBm

17 to 31 dBm

 

15 to 29 dBm

 

15 to 29 dBm

 

 

 

 

 

 

 

 

 

 

700

MHz

21 to 35 dBm

17 to 31 dBm

 

15 to 29 dBm

 

15 to 29 dBm

 

 

 

 

 

 

 

 

 

 

900

MHz

15 to 29 dBm

15 to 29 dBm

 

15 to 29 dBm

 

15 to 29 dBm

 

 

 

 

 

 

 

 

 

 

2500

MHz

15 to 29 dBm

15 to 29 dBm

 

15 to 29 dBm

 

15 to 29 dBm

 

 

 

 

 

 

 

 

 

 

 

 

1+1 Radio

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Frequency Band

QPSK

16 QAM

 

32 QAM

 

64 QAM

 

 

 

 

 

 

 

 

 

 

400

MHz

NA

15 to 29 dBm

 

15 to 29 dBm

 

15 to 28 dBm

 

 

 

 

 

 

 

 

 

Lower 700 MHz

21 to 35 dBm

15 to 29 dBm

 

15 to 29 dBm

 

15 to 28 dBm

 

 

 

 

 

 

 

 

 

Upper 700 MHz

21 to 31 dBm

15 to 29 dBm

 

15 to 29 dBm

 

15 to 28 dBm

 

 

 

 

 

 

 

 

 

 

900

MHz

15 to 28 dBm

15 to 28 dBm

 

15 to 28 dBm

 

15 to 28 dBm

 

 

 

 

 

 

 

 

 

 

2500

MHz

15 to 28 dBm

15 to 28 dBm

 

15 to 28 dBm

 

15 to 28 dBm

 

 

 

 

 

 

 

 

 

 

 

 

Aprisa XE Product Description 8.8.84 NA

 

 

 

 

 

 

 

 

 

 

 

 

Introduction | 9

System Gain FCC

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Frequency Band

 

Channel size

 

QPSK

16 QAM

 

32 QAM

 

64 QAM

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

400 MHz

 

25 kHz

 

NA

136 dB

 

132 dB

 

128 dB

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Upper 700 MHz

 

100 kHz

 

137 dB

131 dB

 

127 dB

 

123 dB

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Upper 700 MHz

 

200 kHz

 

133 dB

127 dB

 

123 dB

 

119 dB

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Lower 700 MHz

 

500 kHz

 

134 dB

124 dB

 

120 dB

 

116 dB

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Upper 700 MHz

 

500 kHz

 

130 dB

124 dB

 

120 dB

 

116 dB

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Lower 700 MHz

 

1.0 MHz

 

131 dB

121 dB

 

117 dB

 

113 dB

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Lower 700 MHz

 

1.75 MHz

 

129 dB

119 dB

 

115 dB

 

111 dB

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

900 MHz

 

25 kHz

 

NA

134 dB

 

131 dB

 

128 dB

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

900 MHz

 

50 kHz

 

138 dB

132 dB

 

129 dB

 

126 dB

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

900 MHz

 

100 kHz

 

135 dB

129 dB

 

126 dB

 

123 dB

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

900 MHz

 

200 kHz

 

131 dB

125 dB

 

122 dB

 

119 dB

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2500 MHz

 

250 kHz

 

130 dB

124 dB

 

121 dB

 

118 dB

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2500 MHz

 

500 kHz

 

128 dB

122 dB

 

119 dB

 

116 dB

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Notes

 

Typical performance specified at the antenna port for 10-6 BER.

 

 

 

 

 

 

 

 

The system gain is typically 1 dB greater for a BER of 10-3.

 

 

 

 

 

 

 

 

System Gain = maximum transmit power - receiver sensitivity

 

 

 

 

 

 

 

 

NA (Not Available)

 

 

 

 

 

 

 

 

 

 

Receiver Performance FCC

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Maximum input level

 

-20 dBm

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Dynamic range

 

 

58 to 87 dB (at 10-6 BER)

 

 

 

 

 

 

 

 

 

 

depending on modulation type and channel size

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

C/I ratio

 

 

C/I ratio =

CdB - IdB

 

 

 

 

 

 

 

 

(carrier to interference ratio)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Co-channel

 

 

better than 16 dB at QPSK

 

 

 

 

 

 

 

 

 

 

 

 

better than 20 dB at 16 QAM

 

 

 

 

 

 

 

 

 

 

 

 

better than 23 dB at 32 QAM

 

 

 

 

 

 

 

 

 

 

 

 

better than 27 dB at 64 QAM

 

 

 

 

 

 

 

 

1st adjacent channel

 

better than -5 dB

 

 

 

 

 

 

 

 

2nd adjacent channel

 

better than -30 dB

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Notes

 

Typical performance specified at the antenna port for 10-6 BER.

 

 

 

 

 

 

 

 

The dynamic range is typically 2 dB greater for a BER of 10-3

 

 

 

 

 

Aprisa XE Product Description 8.8.84 NA

10 | Introduction

Link Delays FCC

Note: The default Modem Interleaver Mode setting is on for channel sizes of 250 kHz and greater and off for channel sizes of 200 kHz and less.

Typical 1+0, MHSB end-to-end link delay - interleaver off

Channel size

QPSK

16 QAM

32 QAM

64 QAM

FCC Part

 

 

 

 

 

 

25 kHz

NA

64.4 ms

52.3 ms

44.2 ms

Part 90

 

 

 

 

 

 

25 kHz

NA

51.8 ms

40.6 ms

35.7 ms

Part 101

 

 

 

 

 

 

50 kHz

46.2 ms

24.3 ms

20.2 ms

16.9 ms

Part 101

 

 

 

 

 

 

100 kHz

28.8 ms

15.3 ms

12.7 ms

10.9 ms

Part 101

 

 

 

 

 

 

200 kHz

15.9 ms

8.8 ms

7.3 ms

6.4 ms

Part 101

 

 

 

 

 

 

250 kHz

10.8 ms

6.5 ms

5.5 ms

4.9 ms

Part 27

 

 

 

 

 

 

500 kHz

6.3 ms

3.9 ms

3.4 ms

7.1 ms

Part 27

 

 

 

 

 

 

1.0 MHz

3.8 ms

2.6 ms

2.3 ms

2.2 ms

Part 27

 

 

 

 

 

 

1.75 MHz

3.1 ms

2.3 ms

2.1 ms

2.0 ms

Part 27

 

 

 

 

 

 

Typical 1+0, MHSB end-to-end link delay - interleaver on

Channel size

QPSK

16 QAM

32 QAM

64 QAM

FCC Part

 

 

 

 

 

 

25 kHz

NA

191.6 ms

154.1 ms

129.1 ms

Part 90

 

 

 

 

 

 

25 kHz

NA

153.6 ms

118.9 ms

103.5 ms

Part 101

 

 

 

 

 

 

50 kHz

138.8 ms

70.5 ms

57.9 ms

47.8 ms

Part 101

 

 

 

 

 

 

100 kHz

85.3 ms

43.6 ms

35.3 ms

29.7 ms

Part 101

 

 

 

 

 

 

200 kHz

45.8 ms

23.7 ms

19.3 ms

16.4 ms

Part 101

 

 

 

 

 

 

250 kHz

30.4 ms

17.7 ms

14.5 ms

12.4 ms

Part 27

 

 

 

 

 

 

500 kHz

16.5 ms

9.5 ms

8.2 ms

3.2 ms

Part 27

 

 

 

 

 

 

1.0 MHz

8.8 ms

5.1 ms

4.3 ms

3.9 ms

Part 27

 

 

 

 

 

 

1.75 MHz

5.6 ms

3.5 ms

3.1 ms

2.8 ms

Part 27

 

 

 

 

 

 

Notes The end to end link delays are measured from T1 interface to T1 interface

The delay figures are typical and can vary when the system re-synchronizes

NA (Not Available)

Aprisa XE Product Description 8.8.84 NA

 

 

 

 

 

 

 

 

Introduction | 11

Radios IC

 

 

 

 

 

 

 

Frequency Bands IC

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Frequency Bands

 

Frequency

 

Frequency

Synthesizer

 

 

 

Band

 

Tuning Range

Step Size

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

400

MHz

400 - 470

MHz

6.25 kHz

 

 

 

 

 

 

 

 

 

 

 

 

 

 

900

MHz

928 - 960

MHz

12.5 kHz

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2000

MHz

1900 - 2300

MHz

62.5 kHz

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Modulation

 

16 / 32 / 64 QAM and QPSK (software configurable)

 

 

 

 

 

 

 

 

 

 

Frequency stability (short term)

 

< ±1 ppm

 

 

 

 

 

 

 

 

 

 

 

 

 

Frequency stability (long term)

 

< ±2 ppm

 

 

 

 

 

 

 

 

 

 

 

 

Antenna connector

 

N-type female 50 Ω

 

 

 

 

 

 

 

 

 

 

 

 

 

Notes

Frequency Ranges

Country specific frequency ranges within the above tuning ranges can be accommodated

Frequency stability

Short term frequency stability is defined as changes in frequency due to environmental effects and power supply variations

Long term frequency stability is defined as changes in frequency due to aging of crystal oscillators approx over 5 years

Aprisa XE Product Description 8.8.84 NA

12 | Introduction

Product Range IC

The Aprisa XE terminal provides the following IC frequency bands / channel sizes:

Channel Size

Frequency Band MHz

 

 

 

 

 

 

 

 

 

 

 

kHz

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

MHz

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

25

 

50

 

75

 

100

 

150

 

200

 

500

 

1.00

 

1.75

 

3.50

 

7.00

 

14.00

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

400

 

RSS

 

 

RSS

 

 

RSS

 

 

 

 

 

RSS

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

119

 

 

119

 

 

119

 

 

 

 

 

119

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

900

 

 

 

 

 

 

 

 

 

 

RSS

 

 

 

 

 

RSS

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

119

 

 

 

 

 

119

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2000

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SRSP-

 

 

SRSP-

 

 

SRSP-

 

 

SRSP-

 

 

SRSP-

 

 

SRSP-

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

302

 

 

302

 

 

302

 

 

302

 

 

302

 

 

302

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Aprisa XE Product Description 8.8.84 NA

 

 

 

 

 

 

Introduction | 13

Link Capacity IC

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Channel size

 

QPSK

16 QAM

32 QAM

64 QAM

 

 

 

 

 

 

 

 

 

 

25 kHz

Gross

NA

56 kbit/s

72 kbit/s

88 kbit/s

 

 

 

T1

 

0 timeslots

1 timeslot

1 timeslot

 

 

 

Wayside

 

56 kbit/s

8 kbit/s

24 kbit/s

 

 

 

 

 

 

 

 

 

 

50 kHz

Gross

72 kbit/s

152 kbit/s

192 kbit/s

232 kbit/s

 

 

 

T1

1 timeslot

2 timeslots

3 timeslots

4 timeslots

 

 

 

Wayside

8 kbit/s

24 kbit/s

0 kbit/s

40 kbit/s

 

 

 

 

 

 

 

 

 

 

75 kHz

Gross

128 kbit/s

264 kbit/s

312 kbit/s

400 kbit/s

 

 

 

 

 

 

 

 

 

 

 

T1

2 timeslots

4 timeslots

4 timeslots

6 timeslots

 

 

 

Wayside

0 kbit/s

8 kbit/s

56 kbit/s

16 kbit/s

 

 

 

 

 

 

 

 

 

 

100 kHz

Gross

136 kbit/s

280 kbit/s

352 kbit/s

424 kbit/s

 

 

 

T1

2 timeslots

4 timeslots

5 timeslots

6 timeslots

 

 

 

Wayside

8 kbit/s

24 kbit/s

32 kbit/s

40 kbit/s

 

 

 

 

 

 

 

 

 

 

150 kHz

Gross

264 kbit/s

536 kbit/s

672 kbit/s

808 kbit/s

 

 

 

T1

4 timeslots

8 timeslots

10 timeslots

12 timeslots

 

 

 

Wayside

8 kbit/s

24 kbit/s

32 kbit/s

40 kbit/s

 

 

 

 

 

 

 

 

 

 

200 kHz

Gross

312 kbit/s

632 kbit/s

792 kbit/s

952 kbit/s

 

 

 

T1

4 timeslots

9 timeslots

12 timeslots

14 timeslots

 

 

 

Wayside

56 kbit/s

56 kbit/s

24 kbit/s

56 kbit/s

 

 

 

 

 

 

 

 

 

 

500 kHz

Gross

792 kbit/s

1592 kbit/s

1992 kbit/s

2392 kbit/s

 

 

 

 

 

 

 

 

 

 

 

T1

12 timeslots

1 T1

1 T1

1 T1

 

 

 

Wayside

24 kbit/s

8 kbit/s

408 kbit/s

808 kbit/s

 

 

 

 

 

 

 

 

 

 

1.0 MHz

Gross

1624 kbit/s

3256 kbit/s

4072 kbit/s

4888 kbit/s

 

 

 

T1

1 T1

2 T1s

2 T1s

3 T1s

 

 

 

Wayside

40 kbit/s

88 kbit/s

904 kbit/s

136 kbit/s

 

 

 

 

 

 

 

 

 

 

1.75 MHz

Gross

2872 kbit/s

5752 kbit/s

7192 kbit/s

8632 kbit/s

 

 

 

 

 

 

 

 

 

 

 

T1

1 T1

3 T1s

4 T1s

5 T1s

 

 

 

 

 

 

 

 

 

 

 

Wayside

1288 kbit/s

1000 kbit/s

856 kbit/s

712 kbit/s

 

 

 

 

 

 

 

 

 

 

3.5 MHz

Gross

5720 kbit/s

11448 kbit/s

14312 kbit/s

17176 kbit/s

 

 

 

T1

3 T1s

7 T1s

9 T1s

10 T1s

 

 

 

Wayside

968 kbit/s

360 kbit/s

56 kbit/s

1336 kbit/s

 

 

 

 

 

 

 

 

 

 

7.0 MHz

Gross

11832 kbit/s

23672 kbit/s

29592 kbit/s

35512 kbit/s

 

 

 

T1

7 T1s

14 T1s

18 T1s

22 T1s

 

 

 

Wayside

744 kbit/s

1496 kbit/s

1080 kbit/s

664 kbit/s

 

 

 

 

 

 

 

 

 

 

14 MHz

Gross

NA

47992 kbit/s

59992 kbit/s

65464 kbit/s

 

 

 

T1

 

30 T1s

32 T1s

32 T1s

 

 

 

Wayside

 

472 kbit/s

9304 kbit/s

14776 kbit/s

 

 

 

 

 

 

 

 

 

Notes The capacities specified are for unframed T1 and so require 1584 kbit/s to transport via the radio. The management ethernet capacity must be subtracted from the gross capacity (default 64 kbit/s). See Product Range table for Channel Size / Frequency Band cross reference

NA (Not Available)

Aprisa XE Product Description 8.8.84 NA

14 | Introduction

Receiver Sensitivity IC

 

Channel size

QPSK

16 QAM

 

32 QAM

64 QAM

 

 

 

 

 

 

 

 

25 kHz

NA

-105 dBm

 

-102 dBm

-99 dBm

 

 

 

 

 

 

 

 

50 kHz

-109 dBm

-103 dBm

 

-100 dBm

-97 dBm

 

 

 

 

 

 

 

 

75 kHz

-107 dBm

-101 dBm

 

-98 dBm

-95 dBm

 

 

 

 

 

 

 

 

100 kHz

-106 dBm

-100 dBm

 

-97 dBm

-94 dBm

 

 

 

 

 

 

 

 

150 kHz

-104 dBm

-98 dBm

 

-95 dBm

-92 dBm

 

 

 

 

 

 

 

 

200 kHz

-102 dBm

-96 dBm

 

-93 dBm

-90 dBm

 

 

 

 

 

 

 

 

500 kHz

-99 dBm

-93 dBm

 

-90 dBm

-87 dBm

 

 

 

 

 

 

 

 

 

1.0

MHz

-96 dBm

-90 dBm

 

-87 dBm

-84 dBm

 

 

 

 

 

 

 

 

 

1.75

MHz

-94 dBm

-88 dBm

 

-85 dBm

-82 dBm

 

 

 

 

 

 

 

 

 

3.5

MHz

-90 dBm

-84 dBm

 

-81 dBm

-78 dBm

 

 

 

 

 

 

 

 

 

7.0

MHz

-87 dBm

-81 dBm

 

-78 dBm

-75 dBm

 

 

 

 

 

 

 

 

 

14

MHz

NA

-78 dBm

 

-75 dBm

-72 dBm

 

 

 

 

 

 

 

Notes Typical performance specified at the antenna port for 10-6 BER.

 

 

 

The receiver is typically 1 dB more sensitive for a BER of 10-3.

 

 

 

NA (Not Available)

 

 

 

 

 

Transmitter Power IC

Frequency Band

QPSK

16 QAM

32 QAM

64 QAM

 

 

 

 

 

 

400

MHz

21 to 35 dBm

17 to 31 dBm

16 to 30 dBm

15 to 29 dBm

 

 

 

 

 

 

900

MHz

15 to 29 dBm

15 to 29 dBm

15 to 29 dBm

15 to 29 dBm

 

 

 

 

 

 

2000

MHz

20 to 34 dBm

17 to 31 dBm

16 to 30 dBm

15 to 29 dBm

 

 

 

 

 

 

Aprisa XE Product Description 8.8.84 NA

 

 

 

 

 

 

 

 

 

Introduction | 15

System Gain IC

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Channel size

 

QPSK

 

16 QAM

 

32 QAM

64 QAM

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

25 kHz

 

NA

 

136 dB

 

132 dB

128 dB

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

50 kHz

 

144 dB

 

134 dB

 

130 dB

126 dB

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

75 kHz

 

142 dB

 

132 dB

 

128 dB

124 dB

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

100 kHz

 

135 dB

 

129 dB

 

126 dB

123 dB

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

150 kHz

 

139 dB

 

129 dB

 

125 dB

121 dB

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

200 kHz

 

131 dB

 

125 dB

 

122 dB

119 dB

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

500 kHz

 

133 dB

 

124 dB

 

120 dB

116 dB

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1.0 MHz

 

130 dB

 

121 dB

 

117 dB

113 dB

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1.75 MHz

 

128 dB

 

119 dB

 

115 dB

111 dB

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3.5 MHz

 

124 dB

 

115 dB

 

111 dB

107 dB

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

7.0 MHz

 

121 dB

 

112 dB

 

108 dB

104 dB

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

14 MHz

 

NA

 

109 dB

 

105 dB

101 dB

 

 

 

 

 

 

 

 

 

 

 

 

Notes Typical performance specified at the antenna port for 10-6 BER.

 

 

 

 

 

 

The system gain is typically 1 dB greater for a BER of 10-3.

 

 

 

 

 

 

System Gain = maximum transmit power - receiver sensitivity

 

 

 

 

 

 

NA (Not Available)

 

 

 

 

 

 

 

 

Receiver Performance

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Maximum input level

 

 

-20 dBm

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Dynamic range

 

 

58 to 87 dB (at 10-6 BER)

 

 

 

 

 

 

 

 

depending on modulation type and channel size

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

C/I ratio

 

 

C/I ratio = CdB - IdB

 

 

 

 

 

 

(carrier to interference ratio)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Co-channel

 

 

better than 16 dB at QPSK

 

 

 

 

 

 

 

 

 

better than 20 dB at 16 QAM

 

 

 

 

 

 

 

 

 

better than 23 dB at 32 QAM

 

 

 

 

 

 

 

 

 

better than 27 dB at 64 QAM

 

 

 

 

 

1st adjacent channel

 

 

better than -5 dB

 

 

 

 

 

 

2nd adjacent channel

 

 

better than -30 dB

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Notes Typical performance specified at the antenna port for 10-6 BER.

The dynamic range is typically 2 dB greater for a BER of 10-3

Aprisa XE Product Description 8.8.84 NA

+ 56 hidden pages