4IPNET 130001 User Manual

Loading...
4IPNET 130001 User Manual

EAP220 V1.00

Enterprise Access Point

Quick Installation Guide

EAP220 Enterprise Access Point ENGLISH

Copyright Notice

This document is protected by USA copyright laws and other laws. Besides, the document is the property of 4IPNET, INC. You may not copy, reproduce, distribute, publish, display, perform, or modify any part of this publication in any form or by any means without prior written permission from 4IPNET, INC. You may not alter or remove any copyright or other notice from copies of the content. All other brand and product names are claimed or registered marks of their respective companies or organizations.

All rights reserved.

To download up-to-date version, please visit www.4ipnet.com.

Copyright © 4IPNET, INC. All rights reserved.

i

Quick Installation Guide

EAP220 Enterprise Access Point ENGLISH

FCC CAUTION

This equipment has been tested and proven to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

---Reorient or relocate the receiving antenna.

---Increase the separation between the equipment and receiver.

---Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

---Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

The device contains a low power transmitter which will send out Radio Frequency (RF) signal when transmitting. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.

This device and its antennas(s) must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC multi-transmitter product procedures. For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible. This device is going to be operated in 5.15~5.25GHz frequency range, it is restricted in indoor environment only.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

Copyright © 4IPNET, INC. All rights reserved.

ii

Quick Installation Guide

EAP220 Enterprise Access Point ENGLISH

CE CAUTION

Declaration of Conformity with Regard to the 1999/5/EC (R&TTE Directive) for European Community, Switzerland, Norway, Iceland, and Liechtenstein Model: EAP220

For 2.4 GHz radios, the device has been tested and passed the requirements of the following standards, and hence fulfills the EMC and safety requirements of R&TTE Directive within the CE marking requirement.

Radio: EN 300.328:

EMC: EN 301.489-1, EN 301.489-17,

EMC: EN 55022 Class B, EN 55024:+ A1 + A2 including the followings: EN 61000-3-2, EN 61000-3-3.

EN 61000-4-2, EN 61000-4-3, EN 61000-4-4, EN 61000-4-5, EN 61000-4-6, EN 61000-4-11

Safety: EN 60950-1 + A11,

Caution:

This declaration is only valid for configurations (combinations of software, firmware, and hardware) provided and supported by 4ipnet Inc. The use of software or firmware not provided and supported by 4ipnet Inc. may result in the equipment no longer being compliant with the regulatory requirements.

European standards dictate maximum radiated transmit power of 100mW EIRP and frequency range 2.400-2.4835 GHz. This equipment is intended to be used in all EU and EFTA countries. Outdoor use may be restricted to certain frequencies and/or may require a license for operation. Contact your local regulatory authority for compliance.

Taiwan NCC Statement

NCC :

變更原設計之特性及功能。

第十四條

低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之擾。

Copyright © 4IPNET, INC. All rights reserved.

iii

Quick Installation Guide

EAP220 Enterprise Access Point ENGLISH

Preface

4ipnet EAP220 is a high-end 802.11a/b/g/n 2.4GHz/ 5GHz MIMO Access Point (AP) with two RF cards (2.4GHz RF Card A / 5GHz RF Card B) embedded to maximize deployment flexibility and feasibility for IT administrators.

Complying with the latest industrial wireless security standards that are required in the tightly secured enterprise network environments, EAP220 makes the wireless communication fast, secure and easy. It supports business-grade secure encryption - 802.1X and Wi-Fi Protected Access (WPA and WPA2) ; by pushing a purposely built button, the

4ipWES (Press-n-Connect) feature makes it easy to bridge wireless links of multiple EAP220s for forming a wider wireless network coverage.

EAP220 also features multiple ESSIDs with VLAN tags and multiple Virtual APs; great for enterprise applications, such as separating traffic from different departments using different ESSIDs. The PoE LAN port is able to receive power from Power over Ethernet (PoE) sourcing devices. Its metal case is IP50 anti-dust compliant, which means that EAP220 is well suited to WLAN deployment in industrial environments.

This Quick Installation Guide provides instructions and reference materials to get you started with 4ipnet EAP220.

Package Contents

1.4ipnet EAP220 x 1

2.Quick Installation Guide (QIG) x 1

3.CD-ROM (with User’s Manual and QIG) x 1

4.Ethernet Cable x 1

5.Console Cable x 1

6.Power Adapter (DC 12V) x 1

7.Detachable Antenna x 4

It is recommended to keep the original packing material for possible future shipment when repair or maintenance is required. Any returned product should be packed in its original packaging to prevent damage during delivery.

Copyright © 4IPNET, INC. All rights reserved.

1

+ 11 hidden pages